arch/arm/boot/dts/kirkwood-rd88f6281.dtsi

   1 /*
   2  * Marvell RD88F6181 Common Board descrition
   3  *
   4  * Andrew Lunn <andrew@lunn.ch>
   5  *
   6  * This file is licensed under the terms of the GNU General Public
   7  * License version 2.  This program is licensed "as is" without any
   8  * warranty of any kind, whether express or implied.
   9  *
  10  * This file contains the definitions that are common between the two
  11  * variants of the Marvell Kirkwood Development Board.
  12  */
  13
  14 #include "kirkwood.dtsi"
  15 #include "kirkwood-6281.dtsi"
  16
  17 / {
  18         memory {
  19                 device_type = "memory";
  20                 reg = <0x00000000 0x20000000>;
  21         };
  22
  23         chosen {
  24                 bootargs = "console=ttyS0,115200n8";
  25                 stdout-path = &uart0;
  26         };
  27
  28         mbus {
  29                 pcie-controller {
  30                         status = "okay";
  31
  32                         pcie@1,0 {
  33                                 status = "okay";
  34                         };
  35                 };
  36         };
  37
  38         ocp@f1000000 {
  39                 pinctrl: pin-controller@10000 {
  40                         pinctrl-0 = <&pmx_sdio_cd>;
  41                         pinctrl-names = "default";
  42
  43                         pmx_sdio_cd: pmx-sdio-cd {
  44                                 marvell,pins = "mpp28";
  45                                 marvell,function = "gpio";
  46                         };
  47                 };
  48
  49                 serial@12000 {
  50                         status = "okay";
  51
  52                 };
  53
  54                 sata@80000 {
  55                         status = "okay";
  56                         nr-ports = <2>;
  57                 };
  58                 mvsdio@90000 {
  59                         pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>;
  60                         pinctrl-names = "default";
  61                         status = "okay";
  62                         cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
  63                         /* No WP GPIO */
  64                 };
  65         };
  66
  67         dsa@0 {
  68                 compatible = "marvell,dsa";
  69                 #address-cells = <2>;
  70                 #size-cells = <0>;
  71
  72                 dsa,ethernet = <&eth0>;
  73                 dsa,mii-bus = <&ethphy1>;
  74
  75                 switch@0 {
  76                         #address-cells = <1>;
  77                         #size-cells = <0>;
  78
  79                         port@0 {
  80                                 reg = <0>;
  81                                 label = "lan1";
  82                         };
  83
  84                         port@1 {
  85                                 reg = <1>;
  86                                 label = "lan2";
  87                         };
  88
  89                         port@2 {
  90                                 reg = <2>;
  91                                 label = "lan3";
  92                         };
  93
  94                         port@3 {
  95                                 reg = <3>;
  96                                 label = "lan4";
  97                         };
  98
  99                         port@5 {
 100                                 reg = <5>;
 101                                 label = "cpu";
 102                         };
 103                 };
 104        };
 105 };
 106
 107 &nand {
 108         status = "okay";
 109
 110         partition@0 {
 111                 label = "u-boot";
 112                 reg = <0x0000000 0x100000>;
 113                 read-only;
 114         };
 115
 116         partition@100000 {
 117                 label = "uImage";
 118                 reg = <0x0100000 0x200000>;
 119         };
 120
 121         partition@300000 {
 122                 label = "data";
 123                 reg = <0x0300000 0x500000>;
 124         };
 125 };
 126
 127 &mdio {
 128         status = "okay";
 129
 130         ethphy0: ethernet-phy@0 {
 131                 reg = <0>;
 132         };
 133
 134         ethphy1: ethernet-phy@ff {
 135                 reg = <0xff>; /* No PHY attached */
 136                 speed = <1000>;
 137                 duple = <1>;
 138         };
 139 };
 140
 141 &eth0 {
 142         status = "okay";
 143         ethernet0-port@0 {
 144                 phy-handle = <&ethphy0>;
 145         };
 146 };
 147
 148 &eth1 {
 149         status = "okay";
 150         ethernet1-port@0 {
 151                 phy-handle = <&ethphy1>;
 152         };
 153 };