drivers/tty/synclink_gt.c

   1 /*
   2  * Device driver for Microgate SyncLink GT serial adapters.
   3  *
   4  * written by Paul Fulghum for Microgate Corporation
   5  * paulkf@microgate.com
   6  *
   7  * Microgate and SyncLink are trademarks of Microgate Corporation
   8  *
   9  * This code is released under the GNU General Public License (GPL)
  10  *
  11  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  12  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  13  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  14  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  15  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  16  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  17  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  18  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  19  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  20  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  21  * OF THE POSSIBILITY OF SUCH DAMAGE.
  22  */
  23
  24 /*
  25  * DEBUG OUTPUT DEFINITIONS
  26  *
  27  * uncomment lines below to enable specific types of debug output
  28  *
  29  * DBGINFO   information - most verbose output
  30  * DBGERR    serious errors
  31  * DBGBH     bottom half service routine debugging
  32  * DBGISR    interrupt service routine debugging
  33  * DBGDATA   output receive and transmit data
  34  * DBGTBUF   output transmit DMA buffers and registers
  35  * DBGRBUF   output receive DMA buffers and registers
  36  */
  37
  38 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  39 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  40 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  41 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  42 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  43 /*#define DBGTBUF(info) dump_tbufs(info)*/
  44 /*#define DBGRBUF(info) dump_rbufs(info)*/
  45
  46
  47 #include <linux/module.h>
  48 #include <linux/errno.h>
  49 #include <linux/signal.h>
  50 #include <linux/sched.h>
  51 #include <linux/timer.h>
  52 #include <linux/interrupt.h>
  53 #include <linux/pci.h>
  54 #include <linux/tty.h>
  55 #include <linux/tty_flip.h>
  56 #include <linux/serial.h>
  57 #include <linux/major.h>
  58 #include <linux/string.h>
  59 #include <linux/fcntl.h>
  60 #include <linux/ptrace.h>
  61 #include <linux/ioport.h>
  62 #include <linux/mm.h>
  63 #include <linux/seq_file.h>
  64 #include <linux/slab.h>
  65 #include <linux/netdevice.h>
  66 #include <linux/vmalloc.h>
  67 #include <linux/init.h>
  68 #include <linux/delay.h>
  69 #include <linux/ioctl.h>
  70 #include <linux/termios.h>
  71 #include <linux/bitops.h>
  72 #include <linux/workqueue.h>
  73 #include <linux/hdlc.h>
  74 #include <linux/synclink.h>
  75
  76 #include <asm/io.h>
  77 #include <asm/irq.h>
  78 #include <asm/dma.h>
  79 #include <asm/types.h>
  80 #include <linux/uaccess.h>
  81
  82 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
  83 #define SYNCLINK_GENERIC_HDLC 1
  84 #else
  85 #define SYNCLINK_GENERIC_HDLC 0
  86 #endif
  87
  88 /*
  89  * module identification
  90  */
  91 static char *driver_name     = "SyncLink GT";
  92 static char *slgt_driver_name = "synclink_gt";
  93 static char *tty_dev_prefix  = "ttySLG";
  94 MODULE_LICENSE("GPL");
  95 #define MGSL_MAGIC 0x5401
  96 #define MAX_DEVICES 32
  97
  98 static struct pci_device_id pci_table[] = {
  99         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 100         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 101         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 102         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 103         {0,}, /* terminate list */
 104 };
 105 MODULE_DEVICE_TABLE(pci, pci_table);
 106
 107 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 108 static void remove_one(struct pci_dev *dev);
 109 static struct pci_driver pci_driver = {
 110         .name           = "synclink_gt",
 111         .id_table       = pci_table,
 112         .probe          = init_one,
 113         .remove         = remove_one,
 114 };
 115
 116 static bool pci_registered;
 117
 118 /*
 119  * module configuration and status
 120  */
 121 static struct slgt_info *slgt_device_list;
 122 static int slgt_device_count;
 123
 124 static int ttymajor;
 125 static int debug_level;
 126 static int maxframe[MAX_DEVICES];
 127
 128 module_param(ttymajor, int, 0);
 129 module_param(debug_level, int, 0);
 130 module_param_array(maxframe, int, NULL, 0);
 131
 132 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 133 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 134 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 135
 136 /*
 137  * tty support and callbacks
 138  */
 139 static struct tty_driver *serial_driver;
 140
 141 static int  open(struct tty_struct *tty, struct file * filp);
 142 static void close(struct tty_struct *tty, struct file * filp);
 143 static void hangup(struct tty_struct *tty);
 144 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
 145
 146 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 147 static int put_char(struct tty_struct *tty, unsigned char ch);
 148 static void send_xchar(struct tty_struct *tty, char ch);
 149 static void wait_until_sent(struct tty_struct *tty, int timeout);
 150 static int  write_room(struct tty_struct *tty);
 151 static void flush_chars(struct tty_struct *tty);
 152 static void flush_buffer(struct tty_struct *tty);
 153 static void tx_hold(struct tty_struct *tty);
 154 static void tx_release(struct tty_struct *tty);
 155
 156 static int  ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
 157 static int  chars_in_buffer(struct tty_struct *tty);
 158 static void throttle(struct tty_struct * tty);
 159 static void unthrottle(struct tty_struct * tty);
 160 static int set_break(struct tty_struct *tty, int break_state);
 161
 162 /*
 163  * generic HDLC support and callbacks
 164  */
 165 #if SYNCLINK_GENERIC_HDLC
 166 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 167 static void hdlcdev_tx_done(struct slgt_info *info);
 168 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 169 static int  hdlcdev_init(struct slgt_info *info);
 170 static void hdlcdev_exit(struct slgt_info *info);
 171 #endif
 172
 173
 174 /*
 175  * device specific structures, macros and functions
 176  */
 177
 178 #define SLGT_MAX_PORTS 4
 179 #define SLGT_REG_SIZE  256
 180
 181 /*
 182  * conditional wait facility
 183  */
 184 struct cond_wait {
 185         struct cond_wait *next;
 186         wait_queue_head_t q;
 187         wait_queue_t wait;
 188         unsigned int data;
 189 };
 190 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 191 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 192 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 193 static void flush_cond_wait(struct cond_wait **head);
 194
 195 /*
 196  * DMA buffer descriptor and access macros
 197  */
 198 struct slgt_desc
 199 {
 200         __le16 count;
 201         __le16 status;
 202         __le32 pbuf;  /* physical address of data buffer */
 203         __le32 next;  /* physical address of next descriptor */
 204
 205         /* driver book keeping */
 206         char *buf;          /* virtual  address of data buffer */
 207         unsigned int pdesc; /* physical address of this descriptor */
 208         dma_addr_t buf_dma_addr;
 209         unsigned short buf_count;
 210 };
 211
 212 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 213 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 214 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 215 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 216 #define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
 217 #define desc_count(a)      (le16_to_cpu((a).count))
 218 #define desc_status(a)     (le16_to_cpu((a).status))
 219 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 220 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 221 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 222 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 223 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 224
 225 struct _input_signal_events {
 226         int ri_up;
 227         int ri_down;
 228         int dsr_up;
 229         int dsr_down;
 230         int dcd_up;
 231         int dcd_down;
 232         int cts_up;
 233         int cts_down;
 234 };
 235
 236 /*
 237  * device instance data structure
 238  */
 239 struct slgt_info {
 240         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 241         struct tty_port port;
 242
 243         struct slgt_info *next_device;  /* device list link */
 244
 245         int magic;
 246
 247         char device_name[25];
 248         struct pci_dev *pdev;
 249
 250         int port_count;  /* count of ports on adapter */
 251         int adapter_num; /* adapter instance number */
 252         int port_num;    /* port instance number */
 253
 254         /* array of pointers to port contexts on this adapter */
 255         struct slgt_info *port_array[SLGT_MAX_PORTS];
 256
 257         int                     line;           /* tty line instance number */
 258
 259         struct mgsl_icount      icount;
 260
 261         int                     timeout;
 262         int                     x_char;         /* xon/xoff character */
 263         unsigned int            read_status_mask;
 264         unsigned int            ignore_status_mask;
 265
 266         wait_queue_head_t       status_event_wait_q;
 267         wait_queue_head_t       event_wait_q;
 268         struct timer_list       tx_timer;
 269         struct timer_list       rx_timer;
 270
 271         unsigned int            gpio_present;
 272         struct cond_wait        *gpio_wait_q;
 273
 274         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 275
 276         struct work_struct task;
 277         u32 pending_bh;
 278         bool bh_requested;
 279         bool bh_running;
 280
 281         int isr_overflow;
 282         bool irq_requested;     /* true if IRQ requested */
 283         bool irq_occurred;      /* for diagnostics use */
 284
 285         /* device configuration */
 286
 287         unsigned int bus_type;
 288         unsigned int irq_level;
 289         unsigned long irq_flags;
 290
 291         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 292         u32 phys_reg_addr;
 293         bool reg_addr_requested;
 294
 295         MGSL_PARAMS params;       /* communications parameters */
 296         u32 idle_mode;
 297         u32 max_frame_size;       /* as set by device config */
 298
 299         unsigned int rbuf_fill_level;
 300         unsigned int rx_pio;
 301         unsigned int if_mode;
 302         unsigned int base_clock;
 303         unsigned int xsync;
 304         unsigned int xctrl;
 305
 306         /* device status */
 307
 308         bool rx_enabled;
 309         bool rx_restart;
 310
 311         bool tx_enabled;
 312         bool tx_active;
 313
 314         unsigned char signals;    /* serial signal states */
 315         int init_error;  /* initialization error */
 316
 317         unsigned char *tx_buf;
 318         int tx_count;
 319
 320         char *flag_buf;
 321         bool drop_rts_on_tx_done;
 322         struct  _input_signal_events    input_signal_events;
 323
 324         int dcd_chkcount;       /* check counts to prevent */
 325         int cts_chkcount;       /* too many IRQs if a signal */
 326         int dsr_chkcount;       /* is floating */
 327         int ri_chkcount;
 328
 329         char *bufs;             /* virtual address of DMA buffer lists */
 330         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 331
 332         unsigned int rbuf_count;
 333         struct slgt_desc *rbufs;
 334         unsigned int rbuf_current;
 335         unsigned int rbuf_index;
 336         unsigned int rbuf_fill_index;
 337         unsigned short rbuf_fill_count;
 338
 339         unsigned int tbuf_count;
 340         struct slgt_desc *tbufs;
 341         unsigned int tbuf_current;
 342         unsigned int tbuf_start;
 343
 344         unsigned char *tmp_rbuf;
 345         unsigned int tmp_rbuf_count;
 346
 347         /* SPPP/Cisco HDLC device parts */
 348
 349         int netcount;
 350         spinlock_t netlock;
 351 #if SYNCLINK_GENERIC_HDLC
 352         struct net_device *netdev;
 353 #endif
 354
 355 };
 356
 357 static MGSL_PARAMS default_params = {
 358         .mode            = MGSL_MODE_HDLC,
 359         .loopback        = 0,
 360         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 361         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 362         .clock_speed     = 0,
 363         .addr_filter     = 0xff,
 364         .crc_type        = HDLC_CRC_16_CCITT,
 365         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 366         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 367         .data_rate       = 9600,
 368         .data_bits       = 8,
 369         .stop_bits       = 1,
 370         .parity          = ASYNC_PARITY_NONE
 371 };
 372
 373
 374 #define BH_RECEIVE  1
 375 #define BH_TRANSMIT 2
 376 #define BH_STATUS   4
 377 #define IO_PIN_SHUTDOWN_LIMIT 100
 378
 379 #define DMABUFSIZE 256
 380 #define DESC_LIST_SIZE 4096
 381
 382 #define MASK_PARITY  BIT1
 383 #define MASK_FRAMING BIT0
 384 #define MASK_BREAK   BIT14
 385 #define MASK_OVERRUN BIT4
 386
 387 #define GSR   0x00 /* global status */
 388 #define JCR   0x04 /* JTAG control */
 389 #define IODR  0x08 /* GPIO direction */
 390 #define IOER  0x0c /* GPIO interrupt enable */
 391 #define IOVR  0x10 /* GPIO value */
 392 #define IOSR  0x14 /* GPIO interrupt status */
 393 #define TDR   0x80 /* tx data */
 394 #define RDR   0x80 /* rx data */
 395 #define TCR   0x82 /* tx control */
 396 #define TIR   0x84 /* tx idle */
 397 #define TPR   0x85 /* tx preamble */
 398 #define RCR   0x86 /* rx control */
 399 #define VCR   0x88 /* V.24 control */
 400 #define CCR   0x89 /* clock control */
 401 #define BDR   0x8a /* baud divisor */
 402 #define SCR   0x8c /* serial control */
 403 #define SSR   0x8e /* serial status */
 404 #define RDCSR 0x90 /* rx DMA control/status */
 405 #define TDCSR 0x94 /* tx DMA control/status */
 406 #define RDDAR 0x98 /* rx DMA descriptor address */
 407 #define TDDAR 0x9c /* tx DMA descriptor address */
 408 #define XSR   0x40 /* extended sync pattern */
 409 #define XCR   0x44 /* extended control */
 410
 411 #define RXIDLE      BIT14
 412 #define RXBREAK     BIT14
 413 #define IRQ_TXDATA  BIT13
 414 #define IRQ_TXIDLE  BIT12
 415 #define IRQ_TXUNDER BIT11 /* HDLC */
 416 #define IRQ_RXDATA  BIT10
 417 #define IRQ_RXIDLE  BIT9  /* HDLC */
 418 #define IRQ_RXBREAK BIT9  /* async */
 419 #define IRQ_RXOVER  BIT8
 420 #define IRQ_DSR     BIT7
 421 #define IRQ_CTS     BIT6
 422 #define IRQ_DCD     BIT5
 423 #define IRQ_RI      BIT4
 424 #define IRQ_ALL     0x3ff0
 425 #define IRQ_MASTER  BIT0
 426
 427 #define slgt_irq_on(info, mask) \
 428         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 429 #define slgt_irq_off(info, mask) \
 430         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 431
 432 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 433 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 434 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 435 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 436 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 437 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 438
 439 static void  msc_set_vcr(struct slgt_info *info);
 440
 441 static int  startup(struct slgt_info *info);
 442 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 443 static void shutdown(struct slgt_info *info);
 444 static void program_hw(struct slgt_info *info);
 445 static void change_params(struct slgt_info *info);
 446
 447 static int  register_test(struct slgt_info *info);
 448 static int  irq_test(struct slgt_info *info);
 449 static int  loopback_test(struct slgt_info *info);
 450 static int  adapter_test(struct slgt_info *info);
 451
 452 static void reset_adapter(struct slgt_info *info);
 453 static void reset_port(struct slgt_info *info);
 454 static void async_mode(struct slgt_info *info);
 455 static void sync_mode(struct slgt_info *info);
 456
 457 static void rx_stop(struct slgt_info *info);
 458 static void rx_start(struct slgt_info *info);
 459 static void reset_rbufs(struct slgt_info *info);
 460 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 461 static void rdma_reset(struct slgt_info *info);
 462 static bool rx_get_frame(struct slgt_info *info);
 463 static bool rx_get_buf(struct slgt_info *info);
 464
 465 static void tx_start(struct slgt_info *info);
 466 static void tx_stop(struct slgt_info *info);
 467 static void tx_set_idle(struct slgt_info *info);
 468 static unsigned int free_tbuf_count(struct slgt_info *info);
 469 static unsigned int tbuf_bytes(struct slgt_info *info);
 470 static void reset_tbufs(struct slgt_info *info);
 471 static void tdma_reset(struct slgt_info *info);
 472 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 473
 474 static void get_signals(struct slgt_info *info);
 475 static void set_signals(struct slgt_info *info);
 476 static void enable_loopback(struct slgt_info *info);
 477 static void set_rate(struct slgt_info *info, u32 data_rate);
 478
 479 static int  bh_action(struct slgt_info *info);
 480 static void bh_handler(struct work_struct *work);
 481 static void bh_transmit(struct slgt_info *info);
 482 static void isr_serial(struct slgt_info *info);
 483 static void isr_rdma(struct slgt_info *info);
 484 static void isr_txeom(struct slgt_info *info, unsigned short status);
 485 static void isr_tdma(struct slgt_info *info);
 486
 487 static int  alloc_dma_bufs(struct slgt_info *info);
 488 static void free_dma_bufs(struct slgt_info *info);
 489 static int  alloc_desc(struct slgt_info *info);
 490 static void free_desc(struct slgt_info *info);
 491 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 492 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 493
 494 static int  alloc_tmp_rbuf(struct slgt_info *info);
 495 static void free_tmp_rbuf(struct slgt_info *info);
 496
 497 static void tx_timeout(unsigned long context);
 498 static void rx_timeout(unsigned long context);
 499
 500 /*
 501  * ioctl handlers
 502  */
 503 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 504 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 505 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 506 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 507 static int  set_txidle(struct slgt_info *info, int idle_mode);
 508 static int  tx_enable(struct slgt_info *info, int enable);
 509 static int  tx_abort(struct slgt_info *info);
 510 static int  rx_enable(struct slgt_info *info, int enable);
 511 static int  modem_input_wait(struct slgt_info *info,int arg);
 512 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 513 static int  tiocmget(struct tty_struct *tty);
 514 static int  tiocmset(struct tty_struct *tty,
 515                                 unsigned int set, unsigned int clear);
 516 static int set_break(struct tty_struct *tty, int break_state);
 517 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 518 static int  set_interface(struct slgt_info *info, int if_mode);
 519 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 520 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 521 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 522 static int  get_xsync(struct slgt_info *info, int __user *if_mode);
 523 static int  set_xsync(struct slgt_info *info, int if_mode);
 524 static int  get_xctrl(struct slgt_info *info, int __user *if_mode);
 525 static int  set_xctrl(struct slgt_info *info, int if_mode);
 526
 527 /*
 528  * driver functions
 529  */
 530 static void add_device(struct slgt_info *info);
 531 static void device_init(int adapter_num, struct pci_dev *pdev);
 532 static int  claim_resources(struct slgt_info *info);
 533 static void release_resources(struct slgt_info *info);
 534
 535 /*
 536  * DEBUG OUTPUT CODE
 537  */
 538 #ifndef DBGINFO
 539 #define DBGINFO(fmt)
 540 #endif
 541 #ifndef DBGERR
 542 #define DBGERR(fmt)
 543 #endif
 544 #ifndef DBGBH
 545 #define DBGBH(fmt)
 546 #endif
 547 #ifndef DBGISR
 548 #define DBGISR(fmt)
 549 #endif
 550
 551 #ifdef DBGDATA
 552 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 553 {
 554         int i;
 555         int linecount;
 556         printk("%s %s data:\n",info->device_name, label);
 557         while(count) {
 558                 linecount = (count > 16) ? 16 : count;
 559                 for(i=0; i < linecount; i++)
 560                         printk("%02X ",(unsigned char)data[i]);
 561                 for(;i<17;i++)
 562                         printk("   ");
 563                 for(i=0;i<linecount;i++) {
 564                         if (data[i]>=040 && data[i]<=0176)
 565                                 printk("%c",data[i]);
 566                         else
 567                                 printk(".");
 568                 }
 569                 printk("\n");
 570                 data  += linecount;
 571                 count -= linecount;
 572         }
 573 }
 574 #else
 575 #define DBGDATA(info, buf, size, label)
 576 #endif
 577
 578 #ifdef DBGTBUF
 579 static void dump_tbufs(struct slgt_info *info)
 580 {
 581         int i;
 582         printk("tbuf_current=%d\n", info->tbuf_current);
 583         for (i=0 ; i < info->tbuf_count ; i++) {
 584                 printk("%d: count=%04X status=%04X\n",
 585                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 586         }
 587 }
 588 #else
 589 #define DBGTBUF(info)
 590 #endif
 591
 592 #ifdef DBGRBUF
 593 static void dump_rbufs(struct slgt_info *info)
 594 {
 595         int i;
 596         printk("rbuf_current=%d\n", info->rbuf_current);
 597         for (i=0 ; i < info->rbuf_count ; i++) {
 598                 printk("%d: count=%04X status=%04X\n",
 599                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 600         }
 601 }
 602 #else
 603 #define DBGRBUF(info)
 604 #endif
 605
 606 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 607 {
 608 #ifdef SANITY_CHECK
 609         if (!info) {
 610                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 611                 return 1;
 612         }
 613         if (info->magic != MGSL_MAGIC) {
 614                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 615                 return 1;
 616         }
 617 #else
 618         if (!info)
 619                 return 1;
 620 #endif
 621         return 0;
 622 }
 623
 624 /**
 625  * line discipline callback wrappers
 626  *
 627  * The wrappers maintain line discipline references
 628  * while calling into the line discipline.
 629  *
 630  * ldisc_receive_buf  - pass receive data to line discipline
 631  */
 632 static void ldisc_receive_buf(struct tty_struct *tty,
 633                               const __u8 *data, char *flags, int count)
 634 {
 635         struct tty_ldisc *ld;
 636         if (!tty)
 637                 return;
 638         ld = tty_ldisc_ref(tty);
 639         if (ld) {
 640                 if (ld->ops->receive_buf)
 641                         ld->ops->receive_buf(tty, data, flags, count);
 642                 tty_ldisc_deref(ld);
 643         }
 644 }
 645
 646 /* tty callbacks */
 647
 648 static int open(struct tty_struct *tty, struct file *filp)
 649 {
 650         struct slgt_info *info;
 651         int retval, line;
 652         unsigned long flags;
 653
 654         line = tty->index;
 655         if (line >= slgt_device_count) {
 656                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 657                 return -ENODEV;
 658         }
 659
 660         info = slgt_device_list;
 661         while(info && info->line != line)
 662                 info = info->next_device;
 663         if (sanity_check(info, tty->name, "open"))
 664                 return -ENODEV;
 665         if (info->init_error) {
 666                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 667                 return -ENODEV;
 668         }
 669
 670         tty->driver_data = info;
 671         info->port.tty = tty;
 672
 673         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
 674
 675         mutex_lock(&info->port.mutex);
 676         info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 677
 678         spin_lock_irqsave(&info->netlock, flags);
 679         if (info->netcount) {
 680                 retval = -EBUSY;
 681                 spin_unlock_irqrestore(&info->netlock, flags);
 682                 mutex_unlock(&info->port.mutex);
 683                 goto cleanup;
 684         }
 685         info->port.count++;
 686         spin_unlock_irqrestore(&info->netlock, flags);
 687
 688         if (info->port.count == 1) {
 689                 /* 1st open on this device, init hardware */
 690                 retval = startup(info);
 691                 if (retval < 0) {
 692                         mutex_unlock(&info->port.mutex);
 693                         goto cleanup;
 694                 }
 695         }
 696         mutex_unlock(&info->port.mutex);
 697         retval = block_til_ready(tty, filp, info);
 698         if (retval) {
 699                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 700                 goto cleanup;
 701         }
 702
 703         retval = 0;
 704
 705 cleanup:
 706         if (retval) {
 707                 if (tty->count == 1)
 708                         info->port.tty = NULL; /* tty layer will release tty struct */
 709                 if(info->port.count)
 710                         info->port.count--;
 711         }
 712
 713         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 714         return retval;
 715 }
 716
 717 static void close(struct tty_struct *tty, struct file *filp)
 718 {
 719         struct slgt_info *info = tty->driver_data;
 720
 721         if (sanity_check(info, tty->name, "close"))
 722                 return;
 723         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
 724
 725         if (tty_port_close_start(&info->port, tty, filp) == 0)
 726                 goto cleanup;
 727
 728         mutex_lock(&info->port.mutex);
 729         if (tty_port_initialized(&info->port))
 730                 wait_until_sent(tty, info->timeout);
 731         flush_buffer(tty);
 732         tty_ldisc_flush(tty);
 733
 734         shutdown(info);
 735         mutex_unlock(&info->port.mutex);
 736
 737         tty_port_close_end(&info->port, tty);
 738         info->port.tty = NULL;
 739 cleanup:
 740         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
 741 }
 742
 743 static void hangup(struct tty_struct *tty)
 744 {
 745         struct slgt_info *info = tty->driver_data;
 746         unsigned long flags;
 747
 748         if (sanity_check(info, tty->name, "hangup"))
 749                 return;
 750         DBGINFO(("%s hangup\n", info->device_name));
 751
 752         flush_buffer(tty);
 753
 754         mutex_lock(&info->port.mutex);
 755         shutdown(info);
 756
 757         spin_lock_irqsave(&info->port.lock, flags);
 758         info->port.count = 0;
 759         info->port.tty = NULL;
 760         spin_unlock_irqrestore(&info->port.lock, flags);
 761         tty_port_set_active(&info->port, 0);
 762         mutex_unlock(&info->port.mutex);
 763
 764         wake_up_interruptible(&info->port.open_wait);
 765 }
 766
 767 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 768 {
 769         struct slgt_info *info = tty->driver_data;
 770         unsigned long flags;
 771
 772         DBGINFO(("%s set_termios\n", tty->driver->name));
 773
 774         change_params(info);
 775
 776         /* Handle transition to B0 status */
 777         if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) {
 778                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
 779                 spin_lock_irqsave(&info->lock,flags);
 780                 set_signals(info);
 781                 spin_unlock_irqrestore(&info->lock,flags);
 782         }
 783
 784         /* Handle transition away from B0 status */
 785         if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
 786                 info->signals |= SerialSignal_DTR;
 787                 if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 788                         info->signals |= SerialSignal_RTS;
 789                 spin_lock_irqsave(&info->lock,flags);
 790                 set_signals(info);
 791                 spin_unlock_irqrestore(&info->lock,flags);
 792         }
 793
 794         /* Handle turning off CRTSCTS */
 795         if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
 796                 tty->hw_stopped = 0;
 797                 tx_release(tty);
 798         }
 799 }
 800
 801 static void update_tx_timer(struct slgt_info *info)
 802 {
 803         /*
 804          * use worst case speed of 1200bps to calculate transmit timeout
 805          * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
 806          */
 807         if (info->params.mode == MGSL_MODE_HDLC) {
 808                 int timeout  = (tbuf_bytes(info) * 7) + 1000;
 809                 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
 810         }
 811 }
 812
 813 static int write(struct tty_struct *tty,
 814                  const unsigned char *buf, int count)
 815 {
 816         int ret = 0;
 817         struct slgt_info *info = tty->driver_data;
 818         unsigned long flags;
 819
 820         if (sanity_check(info, tty->name, "write"))
 821                 return -EIO;
 822
 823         DBGINFO(("%s write count=%d\n", info->device_name, count));
 824
 825         if (!info->tx_buf || (count > info->max_frame_size))
 826                 return -EIO;
 827
 828         if (!count || tty->stopped || tty->hw_stopped)
 829                 return 0;
 830
 831         spin_lock_irqsave(&info->lock, flags);
 832
 833         if (info->tx_count) {
 834                 /* send accumulated data from send_char() */
 835                 if (!tx_load(info, info->tx_buf, info->tx_count))
 836                         goto cleanup;
 837                 info->tx_count = 0;
 838         }
 839
 840         if (tx_load(info, buf, count))
 841                 ret = count;
 842
 843 cleanup:
 844         spin_unlock_irqrestore(&info->lock, flags);
 845         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 846         return ret;
 847 }
 848
 849 static int put_char(struct tty_struct *tty, unsigned char ch)
 850 {
 851         struct slgt_info *info = tty->driver_data;
 852         unsigned long flags;
 853         int ret = 0;
 854
 855         if (sanity_check(info, tty->name, "put_char"))
 856                 return 0;
 857         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 858         if (!info->tx_buf)
 859                 return 0;
 860         spin_lock_irqsave(&info->lock,flags);
 861         if (info->tx_count < info->max_frame_size) {
 862                 info->tx_buf[info->tx_count++] = ch;
 863                 ret = 1;
 864         }
 865         spin_unlock_irqrestore(&info->lock,flags);
 866         return ret;
 867 }
 868
 869 static void send_xchar(struct tty_struct *tty, char ch)
 870 {
 871         struct slgt_info *info = tty->driver_data;
 872         unsigned long flags;
 873
 874         if (sanity_check(info, tty->name, "send_xchar"))
 875                 return;
 876         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 877         info->x_char = ch;
 878         if (ch) {
 879                 spin_lock_irqsave(&info->lock,flags);
 880                 if (!info->tx_enabled)
 881                         tx_start(info);
 882                 spin_unlock_irqrestore(&info->lock,flags);
 883         }
 884 }
 885
 886 static void wait_until_sent(struct tty_struct *tty, int timeout)
 887 {
 888         struct slgt_info *info = tty->driver_data;
 889         unsigned long orig_jiffies, char_time;
 890
 891         if (!info )
 892                 return;
 893         if (sanity_check(info, tty->name, "wait_until_sent"))
 894                 return;
 895         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 896         if (!tty_port_initialized(&info->port))
 897                 goto exit;
 898
 899         orig_jiffies = jiffies;
 900
 901         /* Set check interval to 1/5 of estimated time to
 902          * send a character, and make it at least 1. The check
 903          * interval should also be less than the timeout.
 904          * Note: use tight timings here to satisfy the NIST-PCTS.
 905          */
 906
 907         if (info->params.data_rate) {
 908                 char_time = info->timeout/(32 * 5);
 909                 if (!char_time)
 910                         char_time++;
 911         } else
 912                 char_time = 1;
 913
 914         if (timeout)
 915                 char_time = min_t(unsigned long, char_time, timeout);
 916
 917         while (info->tx_active) {
 918                 msleep_interruptible(jiffies_to_msecs(char_time));
 919                 if (signal_pending(current))
 920                         break;
 921                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 922                         break;
 923         }
 924 exit:
 925         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 926 }
 927
 928 static int write_room(struct tty_struct *tty)
 929 {
 930         struct slgt_info *info = tty->driver_data;
 931         int ret;
 932
 933         if (sanity_check(info, tty->name, "write_room"))
 934                 return 0;
 935         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
 936         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
 937         return ret;
 938 }
 939
 940 static void flush_chars(struct tty_struct *tty)
 941 {
 942         struct slgt_info *info = tty->driver_data;
 943         unsigned long flags;
 944
 945         if (sanity_check(info, tty->name, "flush_chars"))
 946                 return;
 947         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
 948
 949         if (info->tx_count <= 0 || tty->stopped ||
 950             tty->hw_stopped || !info->tx_buf)
 951                 return;
 952
 953         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
 954
 955         spin_lock_irqsave(&info->lock,flags);
 956         if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
 957                 info->tx_count = 0;
 958         spin_unlock_irqrestore(&info->lock,flags);
 959 }
 960
 961 static void flush_buffer(struct tty_struct *tty)
 962 {
 963         struct slgt_info *info = tty->driver_data;
 964         unsigned long flags;
 965
 966         if (sanity_check(info, tty->name, "flush_buffer"))
 967                 return;
 968         DBGINFO(("%s flush_buffer\n", info->device_name));
 969
 970         spin_lock_irqsave(&info->lock, flags);
 971         info->tx_count = 0;
 972         spin_unlock_irqrestore(&info->lock, flags);
 973
 974         tty_wakeup(tty);
 975 }
 976
 977 /*
 978  * throttle (stop) transmitter
 979  */
 980 static void tx_hold(struct tty_struct *tty)
 981 {
 982         struct slgt_info *info = tty->driver_data;
 983         unsigned long flags;
 984
 985         if (sanity_check(info, tty->name, "tx_hold"))
 986                 return;
 987         DBGINFO(("%s tx_hold\n", info->device_name));
 988         spin_lock_irqsave(&info->lock,flags);
 989         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
 990                 tx_stop(info);
 991         spin_unlock_irqrestore(&info->lock,flags);
 992 }
 993
 994 /*
 995  * release (start) transmitter
 996  */
 997 static void tx_release(struct tty_struct *tty)
 998 {
 999         struct slgt_info *info = tty->driver_data;
1000         unsigned long flags;
1001
1002         if (sanity_check(info, tty->name, "tx_release"))
1003                 return;
1004         DBGINFO(("%s tx_release\n", info->device_name));
1005         spin_lock_irqsave(&info->lock, flags);
1006         if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
1007                 info->tx_count = 0;
1008         spin_unlock_irqrestore(&info->lock, flags);
1009 }
1010
1011 /*
1012  * Service an IOCTL request
1013  *
1014  * Arguments
1015  *
1016  *      tty     pointer to tty instance data
1017  *      cmd     IOCTL command code
1018  *      arg     command argument/context
1019  *
1020  * Return 0 if success, otherwise error code
1021  */
1022 static int ioctl(struct tty_struct *tty,
1023                  unsigned int cmd, unsigned long arg)
1024 {
1025         struct slgt_info *info = tty->driver_data;
1026         void __user *argp = (void __user *)arg;
1027         int ret;
1028
1029         if (sanity_check(info, tty->name, "ioctl"))
1030                 return -ENODEV;
1031         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1032
1033         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1034             (cmd != TIOCMIWAIT)) {
1035                 if (tty_io_error(tty))
1036                     return -EIO;
1037         }
1038
1039         switch (cmd) {
1040         case MGSL_IOCWAITEVENT:
1041                 return wait_mgsl_event(info, argp);
1042         case TIOCMIWAIT:
1043                 return modem_input_wait(info,(int)arg);
1044         case MGSL_IOCSGPIO:
1045                 return set_gpio(info, argp);
1046         case MGSL_IOCGGPIO:
1047                 return get_gpio(info, argp);
1048         case MGSL_IOCWAITGPIO:
1049                 return wait_gpio(info, argp);
1050         case MGSL_IOCGXSYNC:
1051                 return get_xsync(info, argp);
1052         case MGSL_IOCSXSYNC:
1053                 return set_xsync(info, (int)arg);
1054         case MGSL_IOCGXCTRL:
1055                 return get_xctrl(info, argp);
1056         case MGSL_IOCSXCTRL:
1057                 return set_xctrl(info, (int)arg);
1058         }
1059         mutex_lock(&info->port.mutex);
1060         switch (cmd) {
1061         case MGSL_IOCGPARAMS:
1062                 ret = get_params(info, argp);
1063                 break;
1064         case MGSL_IOCSPARAMS:
1065                 ret = set_params(info, argp);
1066                 break;
1067         case MGSL_IOCGTXIDLE:
1068                 ret = get_txidle(info, argp);
1069                 break;
1070         case MGSL_IOCSTXIDLE:
1071                 ret = set_txidle(info, (int)arg);
1072                 break;
1073         case MGSL_IOCTXENABLE:
1074                 ret = tx_enable(info, (int)arg);
1075                 break;
1076         case MGSL_IOCRXENABLE:
1077                 ret = rx_enable(info, (int)arg);
1078                 break;
1079         case MGSL_IOCTXABORT:
1080                 ret = tx_abort(info);
1081                 break;
1082         case MGSL_IOCGSTATS:
1083                 ret = get_stats(info, argp);
1084                 break;
1085         case MGSL_IOCGIF:
1086                 ret = get_interface(info, argp);
1087                 break;
1088         case MGSL_IOCSIF:
1089                 ret = set_interface(info,(int)arg);
1090                 break;
1091         default:
1092                 ret = -ENOIOCTLCMD;
1093         }
1094         mutex_unlock(&info->port.mutex);
1095         return ret;
1096 }
1097
1098 static int get_icount(struct tty_struct *tty,
1099                                 struct serial_icounter_struct *icount)
1100
1101 {
1102         struct slgt_info *info = tty->driver_data;
1103         struct mgsl_icount cnow;        /* kernel counter temps */
1104         unsigned long flags;
1105
1106         spin_lock_irqsave(&info->lock,flags);
1107         cnow = info->icount;
1108         spin_unlock_irqrestore(&info->lock,flags);
1109
1110         icount->cts = cnow.cts;
1111         icount->dsr = cnow.dsr;
1112         icount->rng = cnow.rng;
1113         icount->dcd = cnow.dcd;
1114         icount->rx = cnow.rx;
1115         icount->tx = cnow.tx;
1116         icount->frame = cnow.frame;
1117         icount->overrun = cnow.overrun;
1118         icount->parity = cnow.parity;
1119         icount->brk = cnow.brk;
1120         icount->buf_overrun = cnow.buf_overrun;
1121
1122         return 0;
1123 }
1124
1125 /*
1126  * support for 32 bit ioctl calls on 64 bit systems
1127  */
1128 #ifdef CONFIG_COMPAT
1129 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1130 {
1131         struct MGSL_PARAMS32 tmp_params;
1132
1133         DBGINFO(("%s get_params32\n", info->device_name));
1134         memset(&tmp_params, 0, sizeof(tmp_params));
1135         tmp_params.mode            = (compat_ulong_t)info->params.mode;
1136         tmp_params.loopback        = info->params.loopback;
1137         tmp_params.flags           = info->params.flags;
1138         tmp_params.encoding        = info->params.encoding;
1139         tmp_params.clock_speed     = (compat_ulong_t)info->params.clock_speed;
1140         tmp_params.addr_filter     = info->params.addr_filter;
1141         tmp_params.crc_type        = info->params.crc_type;
1142         tmp_params.preamble_length = info->params.preamble_length;
1143         tmp_params.preamble        = info->params.preamble;
1144         tmp_params.data_rate       = (compat_ulong_t)info->params.data_rate;
1145         tmp_params.data_bits       = info->params.data_bits;
1146         tmp_params.stop_bits       = info->params.stop_bits;
1147         tmp_params.parity          = info->params.parity;
1148         if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1149                 return -EFAULT;
1150         return 0;
1151 }
1152
1153 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1154 {
1155         struct MGSL_PARAMS32 tmp_params;
1156
1157         DBGINFO(("%s set_params32\n", info->device_name));
1158         if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1159                 return -EFAULT;
1160
1161         spin_lock(&info->lock);
1162         if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1163                 info->base_clock = tmp_params.clock_speed;
1164         } else {
1165                 info->params.mode            = tmp_params.mode;
1166                 info->params.loopback        = tmp_params.loopback;
1167                 info->params.flags           = tmp_params.flags;
1168                 info->params.encoding        = tmp_params.encoding;
1169                 info->params.clock_speed     = tmp_params.clock_speed;
1170                 info->params.addr_filter     = tmp_params.addr_filter;
1171                 info->params.crc_type        = tmp_params.crc_type;
1172                 info->params.preamble_length = tmp_params.preamble_length;
1173                 info->params.preamble        = tmp_params.preamble;
1174                 info->params.data_rate       = tmp_params.data_rate;
1175                 info->params.data_bits       = tmp_params.data_bits;
1176                 info->params.stop_bits       = tmp_params.stop_bits;
1177                 info->params.parity          = tmp_params.parity;
1178         }
1179         spin_unlock(&info->lock);
1180
1181         program_hw(info);
1182
1183         return 0;
1184 }
1185
1186 static long slgt_compat_ioctl(struct tty_struct *tty,
1187                          unsigned int cmd, unsigned long arg)
1188 {
1189         struct slgt_info *info = tty->driver_data;
1190         int rc = -ENOIOCTLCMD;
1191
1192         if (sanity_check(info, tty->name, "compat_ioctl"))
1193                 return -ENODEV;
1194         DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1195
1196         switch (cmd) {
1197
1198         case MGSL_IOCSPARAMS32:
1199                 rc = set_params32(info, compat_ptr(arg));
1200                 break;
1201
1202         case MGSL_IOCGPARAMS32:
1203                 rc = get_params32(info, compat_ptr(arg));
1204                 break;
1205
1206         case MGSL_IOCGPARAMS:
1207         case MGSL_IOCSPARAMS:
1208         case MGSL_IOCGTXIDLE:
1209         case MGSL_IOCGSTATS:
1210         case MGSL_IOCWAITEVENT:
1211         case MGSL_IOCGIF:
1212         case MGSL_IOCSGPIO:
1213         case MGSL_IOCGGPIO:
1214         case MGSL_IOCWAITGPIO:
1215         case MGSL_IOCGXSYNC:
1216         case MGSL_IOCGXCTRL:
1217         case MGSL_IOCSTXIDLE:
1218         case MGSL_IOCTXENABLE:
1219         case MGSL_IOCRXENABLE:
1220         case MGSL_IOCTXABORT:
1221         case TIOCMIWAIT:
1222         case MGSL_IOCSIF:
1223         case MGSL_IOCSXSYNC:
1224         case MGSL_IOCSXCTRL:
1225                 rc = ioctl(tty, cmd, arg);
1226                 break;
1227         }
1228
1229         DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1230         return rc;
1231 }
1232 #else
1233 #define slgt_compat_ioctl NULL
1234 #endif /* ifdef CONFIG_COMPAT */
1235
1236 /*
1237  * proc fs support
1238  */
1239 static inline void line_info(struct seq_file *m, struct slgt_info *info)
1240 {
1241         char stat_buf[30];
1242         unsigned long flags;
1243
1244         seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1245                       info->device_name, info->phys_reg_addr,
1246                       info->irq_level, info->max_frame_size);
1247
1248         /* output current serial signal states */
1249         spin_lock_irqsave(&info->lock,flags);
1250         get_signals(info);
1251         spin_unlock_irqrestore(&info->lock,flags);
1252
1253         stat_buf[0] = 0;
1254         stat_buf[1] = 0;
1255         if (info->signals & SerialSignal_RTS)
1256                 strcat(stat_buf, "|RTS");
1257         if (info->signals & SerialSignal_CTS)
1258                 strcat(stat_buf, "|CTS");
1259         if (info->signals & SerialSignal_DTR)
1260                 strcat(stat_buf, "|DTR");
1261         if (info->signals & SerialSignal_DSR)
1262                 strcat(stat_buf, "|DSR");
1263         if (info->signals & SerialSignal_DCD)
1264                 strcat(stat_buf, "|CD");
1265         if (info->signals & SerialSignal_RI)
1266                 strcat(stat_buf, "|RI");
1267
1268         if (info->params.mode != MGSL_MODE_ASYNC) {
1269                 seq_printf(m, "\tHDLC txok:%d rxok:%d",
1270                                info->icount.txok, info->icount.rxok);
1271                 if (info->icount.txunder)
1272                         seq_printf(m, " txunder:%d", info->icount.txunder);
1273                 if (info->icount.txabort)
1274                         seq_printf(m, " txabort:%d", info->icount.txabort);
1275                 if (info->icount.rxshort)
1276                         seq_printf(m, " rxshort:%d", info->icount.rxshort);
1277                 if (info->icount.rxlong)
1278                         seq_printf(m, " rxlong:%d", info->icount.rxlong);
1279                 if (info->icount.rxover)
1280                         seq_printf(m, " rxover:%d", info->icount.rxover);
1281                 if (info->icount.rxcrc)
1282                         seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1283         } else {
1284                 seq_printf(m, "\tASYNC tx:%d rx:%d",
1285                                info->icount.tx, info->icount.rx);
1286                 if (info->icount.frame)
1287                         seq_printf(m, " fe:%d", info->icount.frame);
1288                 if (info->icount.parity)
1289                         seq_printf(m, " pe:%d", info->icount.parity);
1290                 if (info->icount.brk)
1291                         seq_printf(m, " brk:%d", info->icount.brk);
1292                 if (info->icount.overrun)
1293                         seq_printf(m, " oe:%d", info->icount.overrun);
1294         }
1295
1296         /* Append serial signal status to end */
1297         seq_printf(m, " %s\n", stat_buf+1);
1298
1299         seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1300                        info->tx_active,info->bh_requested,info->bh_running,
1301                        info->pending_bh);
1302 }
1303
1304 /* Called to print information about devices
1305  */
1306 static int synclink_gt_proc_show(struct seq_file *m, void *v)
1307 {
1308         struct slgt_info *info;
1309
1310         seq_puts(m, "synclink_gt driver\n");
1311
1312         info = slgt_device_list;
1313         while( info ) {
1314                 line_info(m, info);
1315                 info = info->next_device;
1316         }
1317         return 0;
1318 }
1319
1320 static int synclink_gt_proc_open(struct inode *inode, struct file *file)
1321 {
1322         return single_open(file, synclink_gt_proc_show, NULL);
1323 }
1324
1325 static const struct file_operations synclink_gt_proc_fops = {
1326         .owner          = THIS_MODULE,
1327         .open           = synclink_gt_proc_open,
1328         .read           = seq_read,
1329         .llseek         = seq_lseek,
1330         .release        = single_release,
1331 };
1332
1333 /*
1334  * return count of bytes in transmit buffer
1335  */
1336 static int chars_in_buffer(struct tty_struct *tty)
1337 {
1338         struct slgt_info *info = tty->driver_data;
1339         int count;
1340         if (sanity_check(info, tty->name, "chars_in_buffer"))
1341                 return 0;
1342         count = tbuf_bytes(info);
1343         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1344         return count;
1345 }
1346
1347 /*
1348  * signal remote device to throttle send data (our receive data)
1349  */
1350 static void throttle(struct tty_struct * tty)
1351 {
1352         struct slgt_info *info = tty->driver_data;
1353         unsigned long flags;
1354
1355         if (sanity_check(info, tty->name, "throttle"))
1356                 return;
1357         DBGINFO(("%s throttle\n", info->device_name));
1358         if (I_IXOFF(tty))
1359                 send_xchar(tty, STOP_CHAR(tty));
1360         if (C_CRTSCTS(tty)) {
1361                 spin_lock_irqsave(&info->lock,flags);
1362                 info->signals &= ~SerialSignal_RTS;
1363                 set_signals(info);
1364                 spin_unlock_irqrestore(&info->lock,flags);
1365         }
1366 }
1367
1368 /*
1369  * signal remote device to stop throttling send data (our receive data)
1370  */
1371 static void unthrottle(struct tty_struct * tty)
1372 {
1373         struct slgt_info *info = tty->driver_data;
1374         unsigned long flags;
1375
1376         if (sanity_check(info, tty->name, "unthrottle"))
1377                 return;
1378         DBGINFO(("%s unthrottle\n", info->device_name));
1379         if (I_IXOFF(tty)) {
1380                 if (info->x_char)
1381                         info->x_char = 0;
1382                 else
1383                         send_xchar(tty, START_CHAR(tty));
1384         }
1385         if (C_CRTSCTS(tty)) {
1386                 spin_lock_irqsave(&info->lock,flags);
1387                 info->signals |= SerialSignal_RTS;
1388                 set_signals(info);
1389                 spin_unlock_irqrestore(&info->lock,flags);
1390         }
1391 }
1392
1393 /*
1394  * set or clear transmit break condition
1395  * break_state  -1=set break condition, 0=clear
1396  */
1397 static int set_break(struct tty_struct *tty, int break_state)
1398 {
1399         struct slgt_info *info = tty->driver_data;
1400         unsigned short value;
1401         unsigned long flags;
1402
1403         if (sanity_check(info, tty->name, "set_break"))
1404                 return -EINVAL;
1405         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1406
1407         spin_lock_irqsave(&info->lock,flags);
1408         value = rd_reg16(info, TCR);
1409         if (break_state == -1)
1410                 value |= BIT6;
1411         else
1412                 value &= ~BIT6;
1413         wr_reg16(info, TCR, value);
1414         spin_unlock_irqrestore(&info->lock,flags);
1415         return 0;
1416 }
1417
1418 #if SYNCLINK_GENERIC_HDLC
1419
1420 /**
1421  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1422  * set encoding and frame check sequence (FCS) options
1423  *
1424  * dev       pointer to network device structure
1425  * encoding  serial encoding setting
1426  * parity    FCS setting
1427  *
1428  * returns 0 if success, otherwise error code
1429  */
1430 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1431                           unsigned short parity)
1432 {
1433         struct slgt_info *info = dev_to_port(dev);
1434         unsigned char  new_encoding;
1435         unsigned short new_crctype;
1436
1437         /* return error if TTY interface open */
1438         if (info->port.count)
1439                 return -EBUSY;
1440
1441         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1442
1443         switch (encoding)
1444         {
1445         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1446         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1447         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1448         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1449         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1450         default: return -EINVAL;
1451         }
1452
1453         switch (parity)
1454         {
1455         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1456         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1457         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1458         default: return -EINVAL;
1459         }
1460
1461         info->params.encoding = new_encoding;
1462         info->params.crc_type = new_crctype;
1463
1464         /* if network interface up, reprogram hardware */
1465         if (info->netcount)
1466                 program_hw(info);
1467
1468         return 0;
1469 }
1470
1471 /**
1472  * called by generic HDLC layer to send frame
1473  *
1474  * skb  socket buffer containing HDLC frame
1475  * dev  pointer to network device structure
1476  */
1477 static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1478                                       struct net_device *dev)
1479 {
1480         struct slgt_info *info = dev_to_port(dev);
1481         unsigned long flags;
1482
1483         DBGINFO(("%s hdlc_xmit\n", dev->name));
1484
1485         if (!skb->len)
1486                 return NETDEV_TX_OK;
1487
1488         /* stop sending until this frame completes */
1489         netif_stop_queue(dev);
1490
1491         /* update network statistics */
1492         dev->stats.tx_packets++;
1493         dev->stats.tx_bytes += skb->len;
1494
1495         /* save start time for transmit timeout detection */
1496         netif_trans_update(dev);
1497
1498         spin_lock_irqsave(&info->lock, flags);
1499         tx_load(info, skb->data, skb->len);
1500         spin_unlock_irqrestore(&info->lock, flags);
1501
1502         /* done with socket buffer, so free it */
1503         dev_kfree_skb(skb);
1504
1505         return NETDEV_TX_OK;
1506 }
1507
1508 /**
1509  * called by network layer when interface enabled
1510  * claim resources and initialize hardware
1511  *
1512  * dev  pointer to network device structure
1513  *
1514  * returns 0 if success, otherwise error code
1515  */
1516 static int hdlcdev_open(struct net_device *dev)
1517 {
1518         struct slgt_info *info = dev_to_port(dev);
1519         int rc;
1520         unsigned long flags;
1521
1522         if (!try_module_get(THIS_MODULE))
1523                 return -EBUSY;
1524
1525         DBGINFO(("%s hdlcdev_open\n", dev->name));
1526
1527         /* generic HDLC layer open processing */
1528         rc = hdlc_open(dev);
1529         if (rc)
1530                 return rc;
1531
1532         /* arbitrate between network and tty opens */
1533         spin_lock_irqsave(&info->netlock, flags);
1534         if (info->port.count != 0 || info->netcount != 0) {
1535                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1536                 spin_unlock_irqrestore(&info->netlock, flags);
1537                 return -EBUSY;
1538         }
1539         info->netcount=1;
1540         spin_unlock_irqrestore(&info->netlock, flags);
1541
1542         /* claim resources and init adapter */
1543         if ((rc = startup(info)) != 0) {
1544                 spin_lock_irqsave(&info->netlock, flags);
1545                 info->netcount=0;
1546                 spin_unlock_irqrestore(&info->netlock, flags);
1547                 return rc;
1548         }
1549
1550         /* assert RTS and DTR, apply hardware settings */
1551         info->signals |= SerialSignal_RTS | SerialSignal_DTR;
1552         program_hw(info);
1553
1554         /* enable network layer transmit */
1555         netif_trans_update(dev);
1556         netif_start_queue(dev);
1557
1558         /* inform generic HDLC layer of current DCD status */
1559         spin_lock_irqsave(&info->lock, flags);
1560         get_signals(info);
1561         spin_unlock_irqrestore(&info->lock, flags);
1562         if (info->signals & SerialSignal_DCD)
1563                 netif_carrier_on(dev);
1564         else
1565                 netif_carrier_off(dev);
1566         return 0;
1567 }
1568
1569 /**
1570  * called by network layer when interface is disabled
1571  * shutdown hardware and release resources
1572  *
1573  * dev  pointer to network device structure
1574  *
1575  * returns 0 if success, otherwise error code
1576  */
1577 static int hdlcdev_close(struct net_device *dev)
1578 {
1579         struct slgt_info *info = dev_to_port(dev);
1580         unsigned long flags;
1581
1582         DBGINFO(("%s hdlcdev_close\n", dev->name));
1583
1584         netif_stop_queue(dev);
1585
1586         /* shutdown adapter and release resources */
1587         shutdown(info);
1588
1589         hdlc_close(dev);
1590
1591         spin_lock_irqsave(&info->netlock, flags);
1592         info->netcount=0;
1593         spin_unlock_irqrestore(&info->netlock, flags);
1594
1595         module_put(THIS_MODULE);
1596         return 0;
1597 }
1598
1599 /**
1600  * called by network layer to process IOCTL call to network device
1601  *
1602  * dev  pointer to network device structure
1603  * ifr  pointer to network interface request structure
1604  * cmd  IOCTL command code
1605  *
1606  * returns 0 if success, otherwise error code
1607  */
1608 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1609 {
1610         const size_t size = sizeof(sync_serial_settings);
1611         sync_serial_settings new_line;
1612         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1613         struct slgt_info *info = dev_to_port(dev);
1614         unsigned int flags;
1615
1616         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1617
1618         /* return error if TTY interface open */
1619         if (info->port.count)
1620                 return -EBUSY;
1621
1622         if (cmd != SIOCWANDEV)
1623                 return hdlc_ioctl(dev, ifr, cmd);
1624
1625         memset(&new_line, 0, sizeof(new_line));
1626
1627         switch(ifr->ifr_settings.type) {
1628         case IF_GET_IFACE: /* return current sync_serial_settings */
1629
1630                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1631                 if (ifr->ifr_settings.size < size) {
1632                         ifr->ifr_settings.size = size; /* data size wanted */
1633                         return -ENOBUFS;
1634                 }
1635
1636                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1637                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1638                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1639                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1640
1641                 switch (flags){
1642                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1643                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1644                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1645                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1646                 default: new_line.clock_type = CLOCK_DEFAULT;
1647                 }
1648
1649                 new_line.clock_rate = info->params.clock_speed;
1650                 new_line.loopback   = info->params.loopback ? 1:0;
1651
1652                 if (copy_to_user(line, &new_line, size))
1653                         return -EFAULT;
1654                 return 0;
1655
1656         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1657
1658                 if(!capable(CAP_NET_ADMIN))
1659                         return -EPERM;
1660                 if (copy_from_user(&new_line, line, size))
1661                         return -EFAULT;
1662
1663                 switch (new_line.clock_type)
1664                 {
1665                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1666                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1667                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1668                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1669                 case CLOCK_DEFAULT:  flags = info->params.flags &
1670                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1671                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1672                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1673                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1674                 default: return -EINVAL;
1675                 }
1676
1677                 if (new_line.loopback != 0 && new_line.loopback != 1)
1678                         return -EINVAL;
1679
1680                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1681                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1682                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1683                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1684                 info->params.flags |= flags;
1685
1686                 info->params.loopback = new_line.loopback;
1687
1688                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1689                         info->params.clock_speed = new_line.clock_rate;
1690                 else
1691                         info->params.clock_speed = 0;
1692
1693                 /* if network interface up, reprogram hardware */
1694                 if (info->netcount)
1695                         program_hw(info);
1696                 return 0;
1697
1698         default:
1699                 return hdlc_ioctl(dev, ifr, cmd);
1700         }
1701 }
1702
1703 /**
1704  * called by network layer when transmit timeout is detected
1705  *
1706  * dev  pointer to network device structure
1707  */
1708 static void hdlcdev_tx_timeout(struct net_device *dev)
1709 {
1710         struct slgt_info *info = dev_to_port(dev);
1711         unsigned long flags;
1712
1713         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1714
1715         dev->stats.tx_errors++;
1716         dev->stats.tx_aborted_errors++;
1717
1718         spin_lock_irqsave(&info->lock,flags);
1719         tx_stop(info);
1720         spin_unlock_irqrestore(&info->lock,flags);
1721
1722         netif_wake_queue(dev);
1723 }
1724
1725 /**
1726  * called by device driver when transmit completes
1727  * reenable network layer transmit if stopped
1728  *
1729  * info  pointer to device instance information
1730  */
1731 static void hdlcdev_tx_done(struct slgt_info *info)
1732 {
1733         if (netif_queue_stopped(info->netdev))
1734                 netif_wake_queue(info->netdev);
1735 }
1736
1737 /**
1738  * called by device driver when frame received
1739  * pass frame to network layer
1740  *
1741  * info  pointer to device instance information
1742  * buf   pointer to buffer contianing frame data
1743  * size  count of data bytes in buf
1744  */
1745 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1746 {
1747         struct sk_buff *skb = dev_alloc_skb(size);
1748         struct net_device *dev = info->netdev;
1749
1750         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1751
1752         if (skb == NULL) {
1753                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1754                 dev->stats.rx_dropped++;
1755                 return;
1756         }
1757
1758         memcpy(skb_put(skb, size), buf, size);
1759
1760         skb->protocol = hdlc_type_trans(skb, dev);
1761
1762         dev->stats.rx_packets++;
1763         dev->stats.rx_bytes += size;
1764
1765         netif_rx(skb);
1766 }
1767
1768 static const struct net_device_ops hdlcdev_ops = {
1769         .ndo_open       = hdlcdev_open,
1770         .ndo_stop       = hdlcdev_close,
1771         .ndo_start_xmit = hdlc_start_xmit,
1772         .ndo_do_ioctl   = hdlcdev_ioctl,
1773         .ndo_tx_timeout = hdlcdev_tx_timeout,
1774 };
1775
1776 /**
1777  * called by device driver when adding device instance
1778  * do generic HDLC initialization
1779  *
1780  * info  pointer to device instance information
1781  *
1782  * returns 0 if success, otherwise error code
1783  */
1784 static int hdlcdev_init(struct slgt_info *info)
1785 {
1786         int rc;
1787         struct net_device *dev;
1788         hdlc_device *hdlc;
1789
1790         /* allocate and initialize network and HDLC layer objects */
1791
1792         dev = alloc_hdlcdev(info);
1793         if (!dev) {
1794                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1795                 return -ENOMEM;
1796         }
1797
1798         /* for network layer reporting purposes only */
1799         dev->mem_start = info->phys_reg_addr;
1800         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1801         dev->irq       = info->irq_level;
1802
1803         /* network layer callbacks and settings */
1804         dev->netdev_ops     = &hdlcdev_ops;
1805         dev->watchdog_timeo = 10 * HZ;
1806         dev->tx_queue_len   = 50;
1807
1808         /* generic HDLC layer callbacks and settings */
1809         hdlc         = dev_to_hdlc(dev);
1810         hdlc->attach = hdlcdev_attach;
1811         hdlc->xmit   = hdlcdev_xmit;
1812
1813         /* register objects with HDLC layer */
1814         rc = register_hdlc_device(dev);
1815         if (rc) {
1816                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1817                 free_netdev(dev);
1818                 return rc;
1819         }
1820
1821         info->netdev = dev;
1822         return 0;
1823 }
1824
1825 /**
1826  * called by device driver when removing device instance
1827  * do generic HDLC cleanup
1828  *
1829  * info  pointer to device instance information
1830  */
1831 static void hdlcdev_exit(struct slgt_info *info)
1832 {
1833         unregister_hdlc_device(info->netdev);
1834         free_netdev(info->netdev);
1835         info->netdev = NULL;
1836 }
1837
1838 #endif /* ifdef CONFIG_HDLC */
1839
1840 /*
1841  * get async data from rx DMA buffers
1842  */
1843 static void rx_async(struct slgt_info *info)
1844 {
1845         struct mgsl_icount *icount = &info->icount;
1846         unsigned int start, end;
1847         unsigned char *p;
1848         unsigned char status;
1849         struct slgt_desc *bufs = info->rbufs;
1850         int i, count;
1851         int chars = 0;
1852         int stat;
1853         unsigned char ch;
1854
1855         start = end = info->rbuf_current;
1856
1857         while(desc_complete(bufs[end])) {
1858                 count = desc_count(bufs[end]) - info->rbuf_index;
1859                 p     = bufs[end].buf + info->rbuf_index;
1860
1861                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1862                 DBGDATA(info, p, count, "rx");
1863
1864                 for(i=0 ; i < count; i+=2, p+=2) {
1865                         ch = *p;
1866                         icount->rx++;
1867
1868                         stat = 0;
1869
1870                         status = *(p + 1) & (BIT1 + BIT0);
1871                         if (status) {
1872                                 if (status & BIT1)
1873                                         icount->parity++;
1874                                 else if (status & BIT0)
1875                                         icount->frame++;
1876                                 /* discard char if tty control flags say so */
1877                                 if (status & info->ignore_status_mask)
1878                                         continue;
1879                                 if (status & BIT1)
1880                                         stat = TTY_PARITY;
1881                                 else if (status & BIT0)
1882                                         stat = TTY_FRAME;
1883                         }
1884                         tty_insert_flip_char(&info->port, ch, stat);
1885                         chars++;
1886                 }
1887
1888                 if (i < count) {
1889                         /* receive buffer not completed */
1890                         info->rbuf_index += i;
1891                         mod_timer(&info->rx_timer, jiffies + 1);
1892                         break;
1893                 }
1894
1895                 info->rbuf_index = 0;
1896                 free_rbufs(info, end, end);
1897
1898                 if (++end == info->rbuf_count)
1899                         end = 0;
1900
1901                 /* if entire list searched then no frame available */
1902                 if (end == start)
1903                         break;
1904         }
1905
1906         if (chars)
1907                 tty_flip_buffer_push(&info->port);
1908 }
1909
1910 /*
1911  * return next bottom half action to perform
1912  */
1913 static int bh_action(struct slgt_info *info)
1914 {
1915         unsigned long flags;
1916         int rc;
1917
1918         spin_lock_irqsave(&info->lock,flags);
1919
1920         if (info->pending_bh & BH_RECEIVE) {
1921                 info->pending_bh &= ~BH_RECEIVE;
1922                 rc = BH_RECEIVE;
1923         } else if (info->pending_bh & BH_TRANSMIT) {
1924                 info->pending_bh &= ~BH_TRANSMIT;
1925                 rc = BH_TRANSMIT;
1926         } else if (info->pending_bh & BH_STATUS) {
1927                 info->pending_bh &= ~BH_STATUS;
1928                 rc = BH_STATUS;
1929         } else {
1930                 /* Mark BH routine as complete */
1931                 info->bh_running = false;
1932                 info->bh_requested = false;
1933                 rc = 0;
1934         }
1935
1936         spin_unlock_irqrestore(&info->lock,flags);
1937
1938         return rc;
1939 }
1940
1941 /*
1942  * perform bottom half processing
1943  */
1944 static void bh_handler(struct work_struct *work)
1945 {
1946         struct slgt_info *info = container_of(work, struct slgt_info, task);
1947         int action;
1948
1949         info->bh_running = true;
1950
1951         while((action = bh_action(info))) {
1952                 switch (action) {
1953                 case BH_RECEIVE:
1954                         DBGBH(("%s bh receive\n", info->device_name));
1955                         switch(info->params.mode) {
1956                         case MGSL_MODE_ASYNC:
1957                                 rx_async(info);
1958                                 break;
1959                         case MGSL_MODE_HDLC:
1960                                 while(rx_get_frame(info));
1961                                 break;
1962                         case MGSL_MODE_RAW:
1963                         case MGSL_MODE_MONOSYNC:
1964                         case MGSL_MODE_BISYNC:
1965                         case MGSL_MODE_XSYNC:
1966                                 while(rx_get_buf(info));
1967                                 break;
1968                         }
1969                         /* restart receiver if rx DMA buffers exhausted */
1970                         if (info->rx_restart)
1971                                 rx_start(info);
1972                         break;
1973                 case BH_TRANSMIT:
1974                         bh_transmit(info);
1975                         break;
1976                 case BH_STATUS:
1977                         DBGBH(("%s bh status\n", info->device_name));
1978                         info->ri_chkcount = 0;
1979                         info->dsr_chkcount = 0;
1980                         info->dcd_chkcount = 0;
1981                         info->cts_chkcount = 0;
1982                         break;
1983                 default:
1984                         DBGBH(("%s unknown action\n", info->device_name));
1985                         break;
1986                 }
1987         }
1988         DBGBH(("%s bh_handler exit\n", info->device_name));
1989 }
1990
1991 static void bh_transmit(struct slgt_info *info)
1992 {
1993         struct tty_struct *tty = info->port.tty;
1994
1995         DBGBH(("%s bh_transmit\n", info->device_name));
1996         if (tty)
1997                 tty_wakeup(tty);
1998 }
1999
2000 static void dsr_change(struct slgt_info *info, unsigned short status)
2001 {
2002         if (status & BIT3) {
2003                 info->signals |= SerialSignal_DSR;
2004                 info->input_signal_events.dsr_up++;
2005         } else {
2006                 info->signals &= ~SerialSignal_DSR;
2007                 info->input_signal_events.dsr_down++;
2008         }
2009         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
2010         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2011                 slgt_irq_off(info, IRQ_DSR);
2012                 return;
2013         }
2014         info->icount.dsr++;
2015         wake_up_interruptible(&info->status_event_wait_q);
2016         wake_up_interruptible(&info->event_wait_q);
2017         info->pending_bh |= BH_STATUS;
2018 }
2019
2020 static void cts_change(struct slgt_info *info, unsigned short status)
2021 {
2022         if (status & BIT2) {
2023                 info->signals |= SerialSignal_CTS;
2024                 info->input_signal_events.cts_up++;
2025         } else {
2026                 info->signals &= ~SerialSignal_CTS;
2027                 info->input_signal_events.cts_down++;
2028         }
2029         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2030         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2031                 slgt_irq_off(info, IRQ_CTS);
2032                 return;
2033         }
2034         info->icount.cts++;
2035         wake_up_interruptible(&info->status_event_wait_q);
2036         wake_up_interruptible(&info->event_wait_q);
2037         info->pending_bh |= BH_STATUS;
2038
2039         if (tty_port_cts_enabled(&info->port)) {
2040                 if (info->port.tty) {
2041                         if (info->port.tty->hw_stopped) {
2042                                 if (info->signals & SerialSignal_CTS) {
2043                                         info->port.tty->hw_stopped = 0;
2044                                         info->pending_bh |= BH_TRANSMIT;
2045                                         return;
2046                                 }
2047                         } else {
2048                                 if (!(info->signals & SerialSignal_CTS))
2049                                         info->port.tty->hw_stopped = 1;
2050                         }
2051                 }
2052         }
2053 }
2054
2055 static void dcd_change(struct slgt_info *info, unsigned short status)
2056 {
2057         if (status & BIT1) {
2058                 info->signals |= SerialSignal_DCD;
2059                 info->input_signal_events.dcd_up++;
2060         } else {
2061                 info->signals &= ~SerialSignal_DCD;
2062                 info->input_signal_events.dcd_down++;
2063         }
2064         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2065         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2066                 slgt_irq_off(info, IRQ_DCD);
2067                 return;
2068         }
2069         info->icount.dcd++;
2070 #if SYNCLINK_GENERIC_HDLC
2071         if (info->netcount) {
2072                 if (info->signals & SerialSignal_DCD)
2073                         netif_carrier_on(info->netdev);
2074                 else
2075                         netif_carrier_off(info->netdev);
2076         }
2077 #endif
2078         wake_up_interruptible(&info->status_event_wait_q);
2079         wake_up_interruptible(&info->event_wait_q);
2080         info->pending_bh |= BH_STATUS;
2081
2082         if (tty_port_check_carrier(&info->port)) {
2083                 if (info->signals & SerialSignal_DCD)
2084                         wake_up_interruptible(&info->port.open_wait);
2085                 else {
2086                         if (info->port.tty)
2087                                 tty_hangup(info->port.tty);
2088                 }
2089         }
2090 }
2091
2092 static void ri_change(struct slgt_info *info, unsigned short status)
2093 {
2094         if (status & BIT0) {
2095                 info->signals |= SerialSignal_RI;
2096                 info->input_signal_events.ri_up++;
2097         } else {
2098                 info->signals &= ~SerialSignal_RI;
2099                 info->input_signal_events.ri_down++;
2100         }
2101         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2102         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2103                 slgt_irq_off(info, IRQ_RI);
2104                 return;
2105         }
2106         info->icount.rng++;
2107         wake_up_interruptible(&info->status_event_wait_q);
2108         wake_up_interruptible(&info->event_wait_q);
2109         info->pending_bh |= BH_STATUS;
2110 }
2111
2112 static void isr_rxdata(struct slgt_info *info)
2113 {
2114         unsigned int count = info->rbuf_fill_count;
2115         unsigned int i = info->rbuf_fill_index;
2116         unsigned short reg;
2117
2118         while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2119                 reg = rd_reg16(info, RDR);
2120                 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2121                 if (desc_complete(info->rbufs[i])) {
2122                         /* all buffers full */
2123                         rx_stop(info);
2124                         info->rx_restart = 1;
2125                         continue;
2126                 }
2127                 info->rbufs[i].buf[count++] = (unsigned char)reg;
2128                 /* async mode saves status byte to buffer for each data byte */
2129                 if (info->params.mode == MGSL_MODE_ASYNC)
2130                         info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2131                 if (count == info->rbuf_fill_level || (reg & BIT10)) {
2132                         /* buffer full or end of frame */
2133                         set_desc_count(info->rbufs[i], count);
2134                         set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2135                         info->rbuf_fill_count = count = 0;
2136                         if (++i == info->rbuf_count)
2137                                 i = 0;
2138                         info->pending_bh |= BH_RECEIVE;
2139                 }
2140         }
2141
2142         info->rbuf_fill_index = i;
2143         info->rbuf_fill_count = count;
2144 }
2145
2146 static void isr_serial(struct slgt_info *info)
2147 {
2148         unsigned short status = rd_reg16(info, SSR);
2149
2150         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2151
2152         wr_reg16(info, SSR, status); /* clear pending */
2153
2154         info->irq_occurred = true;
2155
2156         if (info->params.mode == MGSL_MODE_ASYNC) {
2157                 if (status & IRQ_TXIDLE) {
2158                         if (info->tx_active)
2159                                 isr_txeom(info, status);
2160                 }
2161                 if (info->rx_pio && (status & IRQ_RXDATA))
2162                         isr_rxdata(info);
2163                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2164                         info->icount.brk++;
2165                         /* process break detection if tty control allows */
2166                         if (info->port.tty) {
2167                                 if (!(status & info->ignore_status_mask)) {
2168                                         if (info->read_status_mask & MASK_BREAK) {
2169                                                 tty_insert_flip_char(&info->port, 0, TTY_BREAK);
2170                                                 if (info->port.flags & ASYNC_SAK)
2171                                                         do_SAK(info->port.tty);
2172                                         }
2173                                 }
2174                         }
2175                 }
2176         } else {
2177                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2178                         isr_txeom(info, status);
2179                 if (info->rx_pio && (status & IRQ_RXDATA))
2180                         isr_rxdata(info);
2181                 if (status & IRQ_RXIDLE) {
2182                         if (status & RXIDLE)
2183                                 info->icount.rxidle++;
2184                         else
2185                                 info->icount.exithunt++;
2186                         wake_up_interruptible(&info->event_wait_q);
2187                 }
2188
2189                 if (status & IRQ_RXOVER)
2190                         rx_start(info);
2191         }
2192
2193         if (status & IRQ_DSR)
2194                 dsr_change(info, status);
2195         if (status & IRQ_CTS)
2196                 cts_change(info, status);
2197         if (status & IRQ_DCD)
2198                 dcd_change(info, status);
2199         if (status & IRQ_RI)
2200                 ri_change(info, status);
2201 }
2202
2203 static void isr_rdma(struct slgt_info *info)
2204 {
2205         unsigned int status = rd_reg32(info, RDCSR);
2206
2207         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2208
2209         /* RDCSR (rx DMA control/status)
2210          *
2211          * 31..07  reserved
2212          * 06      save status byte to DMA buffer
2213          * 05      error
2214          * 04      eol (end of list)
2215          * 03      eob (end of buffer)
2216          * 02      IRQ enable
2217          * 01      reset
2218          * 00      enable
2219          */
2220         wr_reg32(info, RDCSR, status);  /* clear pending */
2221
2222         if (status & (BIT5 + BIT4)) {
2223                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2224                 info->rx_restart = true;
2225         }
2226         info->pending_bh |= BH_RECEIVE;
2227 }
2228
2229 static void isr_tdma(struct slgt_info *info)
2230 {
2231         unsigned int status = rd_reg32(info, TDCSR);
2232
2233         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2234
2235         /* TDCSR (tx DMA control/status)
2236          *
2237          * 31..06  reserved
2238          * 05      error
2239          * 04      eol (end of list)
2240          * 03      eob (end of buffer)
2241          * 02      IRQ enable
2242          * 01      reset
2243          * 00      enable
2244          */
2245         wr_reg32(info, TDCSR, status);  /* clear pending */
2246
2247         if (status & (BIT5 + BIT4 + BIT3)) {
2248                 // another transmit buffer has completed
2249                 // run bottom half to get more send data from user
2250                 info->pending_bh |= BH_TRANSMIT;
2251         }
2252 }
2253
2254 /*
2255  * return true if there are unsent tx DMA buffers, otherwise false
2256  *
2257  * if there are unsent buffers then info->tbuf_start
2258  * is set to index of first unsent buffer
2259  */
2260 static bool unsent_tbufs(struct slgt_info *info)
2261 {
2262         unsigned int i = info->tbuf_current;
2263         bool rc = false;
2264
2265         /*
2266          * search backwards from last loaded buffer (precedes tbuf_current)
2267          * for first unsent buffer (desc_count > 0)
2268          */
2269
2270         do {
2271                 if (i)
2272                         i--;
2273                 else
2274                         i = info->tbuf_count - 1;
2275                 if (!desc_count(info->tbufs[i]))
2276                         break;
2277                 info->tbuf_start = i;
2278                 rc = true;
2279         } while (i != info->tbuf_current);
2280
2281         return rc;
2282 }
2283
2284 static void isr_txeom(struct slgt_info *info, unsigned short status)
2285 {
2286         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2287
2288         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2289         tdma_reset(info);
2290         if (status & IRQ_TXUNDER) {
2291                 unsigned short val = rd_reg16(info, TCR);
2292                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2293                 wr_reg16(info, TCR, val); /* clear reset bit */
2294         }
2295
2296         if (info->tx_active) {
2297                 if (info->params.mode != MGSL_MODE_ASYNC) {
2298                         if (status & IRQ_TXUNDER)
2299                                 info->icount.txunder++;
2300                         else if (status & IRQ_TXIDLE)
2301                                 info->icount.txok++;
2302                 }
2303
2304                 if (unsent_tbufs(info)) {
2305                         tx_start(info);
2306                         update_tx_timer(info);
2307                         return;
2308                 }
2309                 info->tx_active = false;
2310
2311                 del_timer(&info->tx_timer);
2312
2313                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2314                         info->signals &= ~SerialSignal_RTS;
2315                         info->drop_rts_on_tx_done = false;
2316                         set_signals(info);
2317                 }
2318
2319 #if SYNCLINK_GENERIC_HDLC
2320                 if (info->netcount)
2321                         hdlcdev_tx_done(info);
2322                 else
2323 #endif
2324                 {
2325                         if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2326                                 tx_stop(info);
2327                                 return;
2328                         }
2329                         info->pending_bh |= BH_TRANSMIT;
2330                 }
2331         }
2332 }
2333
2334 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2335 {
2336         struct cond_wait *w, *prev;
2337
2338         /* wake processes waiting for specific transitions */
2339         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2340                 if (w->data & changed) {
2341                         w->data = state;
2342                         wake_up_interruptible(&w->q);
2343                         if (prev != NULL)
2344                                 prev->next = w->next;
2345                         else
2346                                 info->gpio_wait_q = w->next;
2347                 } else
2348                         prev = w;
2349         }
2350 }
2351
2352 /* interrupt service routine
2353  *
2354  *      irq     interrupt number
2355  *      dev_id  device ID supplied during interrupt registration
2356  */
2357 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2358 {
2359         struct slgt_info *info = dev_id;
2360         unsigned int gsr;
2361         unsigned int i;
2362
2363         DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2364
2365         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2366                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2367                 info->irq_occurred = true;
2368                 for(i=0; i < info->port_count ; i++) {
2369                         if (info->port_array[i] == NULL)
2370                                 continue;
2371                         spin_lock(&info->port_array[i]->lock);
2372                         if (gsr & (BIT8 << i))
2373                                 isr_serial(info->port_array[i]);
2374                         if (gsr & (BIT16 << (i*2)))
2375                                 isr_rdma(info->port_array[i]);
2376                         if (gsr & (BIT17 << (i*2)))
2377                                 isr_tdma(info->port_array[i]);
2378                         spin_unlock(&info->port_array[i]->lock);
2379                 }
2380         }
2381
2382         if (info->gpio_present) {
2383                 unsigned int state;
2384                 unsigned int changed;
2385                 spin_lock(&info->lock);
2386                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2387                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2388                         /* read latched state of GPIO signals */
2389                         state = rd_reg32(info, IOVR);
2390                         /* clear pending GPIO interrupt bits */
2391                         wr_reg32(info, IOSR, changed);
2392                         for (i=0 ; i < info->port_count ; i++) {
2393                                 if (info->port_array[i] != NULL)
2394                                         isr_gpio(info->port_array[i], changed, state);
2395                         }
2396                 }
2397                 spin_unlock(&info->lock);
2398         }
2399
2400         for(i=0; i < info->port_count ; i++) {
2401                 struct slgt_info *port = info->port_array[i];
2402                 if (port == NULL)
2403                         continue;
2404                 spin_lock(&port->lock);
2405                 if ((port->port.count || port->netcount) &&
2406                     port->pending_bh && !port->bh_running &&
2407                     !port->bh_requested) {
2408                         DBGISR(("%s bh queued\n", port->device_name));
2409                         schedule_work(&port->task);
2410                         port->bh_requested = true;
2411                 }
2412                 spin_unlock(&port->lock);
2413         }
2414
2415         DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2416         return IRQ_HANDLED;
2417 }
2418
2419 static int startup(struct slgt_info *info)
2420 {
2421         DBGINFO(("%s startup\n", info->device_name));
2422
2423         if (tty_port_initialized(&info->port))
2424                 return 0;
2425
2426         if (!info->tx_buf) {
2427                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2428                 if (!info->tx_buf) {
2429                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2430                         return -ENOMEM;
2431                 }
2432         }
2433
2434         info->pending_bh = 0;
2435
2436         memset(&info->icount, 0, sizeof(info->icount));
2437
2438         /* program hardware for current parameters */
2439         change_params(info);
2440
2441         if (info->port.tty)
2442                 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2443
2444         tty_port_set_initialized(&info->port, 1);
2445
2446         return 0;
2447 }
2448
2449 /*
2450  *  called by close() and hangup() to shutdown hardware
2451  */
2452 static void shutdown(struct slgt_info *info)
2453 {
2454         unsigned long flags;
2455
2456         if (!tty_port_initialized(&info->port))
2457                 return;
2458
2459         DBGINFO(("%s shutdown\n", info->device_name));
2460
2461         /* clear status wait queue because status changes */
2462         /* can't happen after shutting down the hardware */
2463         wake_up_interruptible(&info->status_event_wait_q);
2464         wake_up_interruptible(&info->event_wait_q);
2465
2466         del_timer_sync(&info->tx_timer);
2467         del_timer_sync(&info->rx_timer);
2468
2469         kfree(info->tx_buf);
2470         info->tx_buf = NULL;
2471
2472         spin_lock_irqsave(&info->lock,flags);
2473
2474         tx_stop(info);
2475         rx_stop(info);
2476
2477         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2478
2479         if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
2480                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2481                 set_signals(info);
2482         }
2483
2484         flush_cond_wait(&info->gpio_wait_q);
2485
2486         spin_unlock_irqrestore(&info->lock,flags);
2487
2488         if (info->port.tty)
2489                 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2490
2491         tty_port_set_initialized(&info->port, 0);
2492 }
2493
2494 static void program_hw(struct slgt_info *info)
2495 {
2496         unsigned long flags;
2497
2498         spin_lock_irqsave(&info->lock,flags);
2499
2500         rx_stop(info);
2501         tx_stop(info);
2502
2503         if (info->params.mode != MGSL_MODE_ASYNC ||
2504             info->netcount)
2505                 sync_mode(info);
2506         else
2507                 async_mode(info);
2508
2509         set_signals(info);
2510
2511         info->dcd_chkcount = 0;
2512         info->cts_chkcount = 0;
2513         info->ri_chkcount = 0;
2514         info->dsr_chkcount = 0;
2515
2516         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2517         get_signals(info);
2518
2519         if (info->netcount ||
2520             (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
2521                 rx_start(info);
2522
2523         spin_unlock_irqrestore(&info->lock,flags);
2524 }
2525
2526 /*
2527  * reconfigure adapter based on new parameters
2528  */
2529 static void change_params(struct slgt_info *info)
2530 {
2531         unsigned cflag;
2532         int bits_per_char;
2533
2534         if (!info->port.tty)
2535                 return;
2536         DBGINFO(("%s change_params\n", info->device_name));
2537
2538         cflag = info->port.tty->termios.c_cflag;
2539
2540         /* if B0 rate (hangup) specified then negate RTS and DTR */
2541         /* otherwise assert RTS and DTR */
2542         if (cflag & CBAUD)
2543                 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
2544         else
2545                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2546
2547         /* byte size and parity */
2548
2549         switch (cflag & CSIZE) {
2550         case CS5: info->params.data_bits = 5; break;
2551         case CS6: info->params.data_bits = 6; break;
2552         case CS7: info->params.data_bits = 7; break;
2553         case CS8: info->params.data_bits = 8; break;
2554         default:  info->params.data_bits = 7; break;
2555         }
2556
2557         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2558
2559         if (cflag & PARENB)
2560                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2561         else
2562                 info->params.parity = ASYNC_PARITY_NONE;
2563
2564         /* calculate number of jiffies to transmit a full
2565          * FIFO (32 bytes) at specified data rate
2566          */
2567         bits_per_char = info->params.data_bits +
2568                         info->params.stop_bits + 1;
2569
2570         info->params.data_rate = tty_get_baud_rate(info->port.tty);
2571
2572         if (info->params.data_rate) {
2573                 info->timeout = (32*HZ*bits_per_char) /
2574                                 info->params.data_rate;
2575         }
2576         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2577
2578         tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
2579         tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
2580
2581         /* process tty input control flags */
2582
2583         info->read_status_mask = IRQ_RXOVER;
2584         if (I_INPCK(info->port.tty))
2585                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2586         if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2587                 info->read_status_mask |= MASK_BREAK;
2588         if (I_IGNPAR(info->port.tty))
2589                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2590         if (I_IGNBRK(info->port.tty)) {
2591                 info->ignore_status_mask |= MASK_BREAK;
2592                 /* If ignoring parity and break indicators, ignore
2593                  * overruns too.  (For real raw support).
2594                  */
2595                 if (I_IGNPAR(info->port.tty))
2596                         info->ignore_status_mask |= MASK_OVERRUN;
2597         }
2598
2599         program_hw(info);
2600 }
2601
2602 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2603 {
2604         DBGINFO(("%s get_stats\n",  info->device_name));
2605         if (!user_icount) {
2606                 memset(&info->icount, 0, sizeof(info->icount));
2607         } else {
2608                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2609                         return -EFAULT;
2610         }
2611         return 0;
2612 }
2613
2614 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2615 {
2616         DBGINFO(("%s get_params\n", info->device_name));
2617         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2618                 return -EFAULT;
2619         return 0;
2620 }
2621
2622 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2623 {
2624         unsigned long flags;
2625         MGSL_PARAMS tmp_params;
2626
2627         DBGINFO(("%s set_params\n", info->device_name));
2628         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2629                 return -EFAULT;
2630
2631         spin_lock_irqsave(&info->lock, flags);
2632         if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2633                 info->base_clock = tmp_params.clock_speed;
2634         else
2635                 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2636         spin_unlock_irqrestore(&info->lock, flags);
2637
2638         program_hw(info);
2639
2640         return 0;
2641 }
2642
2643 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2644 {
2645         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2646         if (put_user(info->idle_mode, idle_mode))
2647                 return -EFAULT;
2648         return 0;
2649 }
2650
2651 static int set_txidle(struct slgt_info *info, int idle_mode)
2652 {
2653         unsigned long flags;
2654         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2655         spin_lock_irqsave(&info->lock,flags);
2656         info->idle_mode = idle_mode;
2657         if (info->params.mode != MGSL_MODE_ASYNC)
2658                 tx_set_idle(info);
2659         spin_unlock_irqrestore(&info->lock,flags);
2660         return 0;
2661 }
2662
2663 static int tx_enable(struct slgt_info *info, int enable)
2664 {
2665         unsigned long flags;
2666         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2667         spin_lock_irqsave(&info->lock,flags);
2668         if (enable) {
2669                 if (!info->tx_enabled)
2670                         tx_start(info);
2671         } else {
2672                 if (info->tx_enabled)
2673                         tx_stop(info);
2674         }
2675         spin_unlock_irqrestore(&info->lock,flags);
2676         return 0;
2677 }
2678
2679 /*
2680  * abort transmit HDLC frame
2681  */
2682 static int tx_abort(struct slgt_info *info)
2683 {
2684         unsigned long flags;
2685         DBGINFO(("%s tx_abort\n", info->device_name));
2686         spin_lock_irqsave(&info->lock,flags);
2687         tdma_reset(info);
2688         spin_unlock_irqrestore(&info->lock,flags);
2689         return 0;
2690 }
2691
2692 static int rx_enable(struct slgt_info *info, int enable)
2693 {
2694         unsigned long flags;
2695         unsigned int rbuf_fill_level;
2696         DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2697         spin_lock_irqsave(&info->lock,flags);
2698         /*
2699          * enable[31..16] = receive DMA buffer fill level
2700          * 0 = noop (leave fill level unchanged)
2701          * fill level must be multiple of 4 and <= buffer size
2702          */
2703         rbuf_fill_level = ((unsigned int)enable) >> 16;
2704         if (rbuf_fill_level) {
2705                 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2706                         spin_unlock_irqrestore(&info->lock, flags);
2707                         return -EINVAL;
2708                 }
2709                 info->rbuf_fill_level = rbuf_fill_level;
2710                 if (rbuf_fill_level < 128)
2711                         info->rx_pio = 1; /* PIO mode */
2712                 else
2713                         info->rx_pio = 0; /* DMA mode */
2714                 rx_stop(info); /* restart receiver to use new fill level */
2715         }
2716
2717         /*
2718          * enable[1..0] = receiver enable command
2719          * 0 = disable
2720          * 1 = enable
2721          * 2 = enable or force hunt mode if already enabled
2722          */
2723         enable &= 3;
2724         if (enable) {
2725                 if (!info->rx_enabled)
2726                         rx_start(info);
2727                 else if (enable == 2) {
2728                         /* force hunt mode (write 1 to RCR[3]) */
2729                         wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2730                 }
2731         } else {
2732                 if (info->rx_enabled)
2733                         rx_stop(info);
2734         }
2735         spin_unlock_irqrestore(&info->lock,flags);
2736         return 0;
2737 }
2738
2739 /*
2740  *  wait for specified event to occur
2741  */
2742 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2743 {
2744         unsigned long flags;
2745         int s;
2746         int rc=0;
2747         struct mgsl_icount cprev, cnow;
2748         int events;
2749         int mask;
2750         struct  _input_signal_events oldsigs, newsigs;
2751         DECLARE_WAITQUEUE(wait, current);
2752
2753         if (get_user(mask, mask_ptr))
2754                 return -EFAULT;
2755
2756         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2757
2758         spin_lock_irqsave(&info->lock,flags);
2759
2760         /* return immediately if state matches requested events */
2761         get_signals(info);
2762         s = info->signals;
2763
2764         events = mask &
2765                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2766                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2767                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2768                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2769         if (events) {
2770                 spin_unlock_irqrestore(&info->lock,flags);
2771                 goto exit;
2772         }
2773
2774         /* save current irq counts */
2775         cprev = info->icount;
2776         oldsigs = info->input_signal_events;
2777
2778         /* enable hunt and idle irqs if needed */
2779         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2780                 unsigned short val = rd_reg16(info, SCR);
2781                 if (!(val & IRQ_RXIDLE))
2782                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2783         }
2784
2785         set_current_state(TASK_INTERRUPTIBLE);
2786         add_wait_queue(&info->event_wait_q, &wait);
2787
2788         spin_unlock_irqrestore(&info->lock,flags);
2789
2790         for(;;) {
2791                 schedule();
2792                 if (signal_pending(current)) {
2793                         rc = -ERESTARTSYS;
2794                         break;
2795                 }
2796
2797                 /* get current irq counts */
2798                 spin_lock_irqsave(&info->lock,flags);
2799                 cnow = info->icount;
2800                 newsigs = info->input_signal_events;
2801                 set_current_state(TASK_INTERRUPTIBLE);
2802                 spin_unlock_irqrestore(&info->lock,flags);
2803
2804                 /* if no change, wait aborted for some reason */
2805                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2806                     newsigs.dsr_down == oldsigs.dsr_down &&
2807                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2808                     newsigs.dcd_down == oldsigs.dcd_down &&
2809                     newsigs.cts_up   == oldsigs.cts_up   &&
2810                     newsigs.cts_down == oldsigs.cts_down &&
2811                     newsigs.ri_up    == oldsigs.ri_up    &&
2812                     newsigs.ri_down  == oldsigs.ri_down  &&
2813                     cnow.exithunt    == cprev.exithunt   &&
2814                     cnow.rxidle      == cprev.rxidle) {
2815                         rc = -EIO;
2816                         break;
2817                 }
2818
2819                 events = mask &
2820                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2821                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2822                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2823                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2824                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2825                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2826                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2827                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2828                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2829                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2830                 if (events)
2831                         break;
2832
2833                 cprev = cnow;
2834                 oldsigs = newsigs;
2835         }
2836
2837         remove_wait_queue(&info->event_wait_q, &wait);
2838         set_current_state(TASK_RUNNING);
2839
2840
2841         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2842                 spin_lock_irqsave(&info->lock,flags);
2843                 if (!waitqueue_active(&info->event_wait_q)) {
2844                         /* disable enable exit hunt mode/idle rcvd IRQs */
2845                         wr_reg16(info, SCR,
2846                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2847                 }
2848                 spin_unlock_irqrestore(&info->lock,flags);
2849         }
2850 exit:
2851         if (rc == 0)
2852                 rc = put_user(events, mask_ptr);
2853         return rc;
2854 }
2855
2856 static int get_interface(struct slgt_info *info, int __user *if_mode)
2857 {
2858         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2859         if (put_user(info->if_mode, if_mode))
2860                 return -EFAULT;
2861         return 0;
2862 }
2863
2864 static int set_interface(struct slgt_info *info, int if_mode)
2865 {
2866         unsigned long flags;
2867         unsigned short val;
2868
2869         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2870         spin_lock_irqsave(&info->lock,flags);
2871         info->if_mode = if_mode;
2872
2873         msc_set_vcr(info);
2874
2875         /* TCR (tx control) 07  1=RTS driver control */
2876         val = rd_reg16(info, TCR);
2877         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2878                 val |= BIT7;
2879         else
2880                 val &= ~BIT7;
2881         wr_reg16(info, TCR, val);
2882
2883         spin_unlock_irqrestore(&info->lock,flags);
2884         return 0;
2885 }
2886
2887 static int get_xsync(struct slgt_info *info, int __user *xsync)
2888 {
2889         DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2890         if (put_user(info->xsync, xsync))
2891                 return -EFAULT;
2892         return 0;
2893 }
2894
2895 /*
2896  * set extended sync pattern (1 to 4 bytes) for extended sync mode
2897  *
2898  * sync pattern is contained in least significant bytes of value
2899  * most significant byte of sync pattern is oldest (1st sent/detected)
2900  */
2901 static int set_xsync(struct slgt_info *info, int xsync)
2902 {
2903         unsigned long flags;
2904
2905         DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2906         spin_lock_irqsave(&info->lock, flags);
2907         info->xsync = xsync;
2908         wr_reg32(info, XSR, xsync);
2909         spin_unlock_irqrestore(&info->lock, flags);
2910         return 0;
2911 }
2912
2913 static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2914 {
2915         DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2916         if (put_user(info->xctrl, xctrl))
2917                 return -EFAULT;
2918         return 0;
2919 }
2920
2921 /*
2922  * set extended control options
2923  *
2924  * xctrl[31:19] reserved, must be zero
2925  * xctrl[18:17] extended sync pattern length in bytes
2926  *              00 = 1 byte  in xsr[7:0]
2927  *              01 = 2 bytes in xsr[15:0]
2928  *              10 = 3 bytes in xsr[23:0]
2929  *              11 = 4 bytes in xsr[31:0]
2930  * xctrl[16]    1 = enable terminal count, 0=disabled
2931  * xctrl[15:0]  receive terminal count for fixed length packets
2932  *              value is count minus one (0 = 1 byte packet)
2933  *              when terminal count is reached, receiver
2934  *              automatically returns to hunt mode and receive
2935  *              FIFO contents are flushed to DMA buffers with
2936  *              end of frame (EOF) status
2937  */
2938 static int set_xctrl(struct slgt_info *info, int xctrl)
2939 {
2940         unsigned long flags;
2941
2942         DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2943         spin_lock_irqsave(&info->lock, flags);
2944         info->xctrl = xctrl;
2945         wr_reg32(info, XCR, xctrl);
2946         spin_unlock_irqrestore(&info->lock, flags);
2947         return 0;
2948 }
2949
2950 /*
2951  * set general purpose IO pin state and direction
2952  *
2953  * user_gpio fields:
2954  * state   each bit indicates a pin state
2955  * smask   set bit indicates pin state to set
2956  * dir     each bit indicates a pin direction (0=input, 1=output)
2957  * dmask   set bit indicates pin direction to set
2958  */
2959 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2960 {
2961         unsigned long flags;
2962         struct gpio_desc gpio;
2963         __u32 data;
2964
2965         if (!info->gpio_present)
2966                 return -EINVAL;
2967         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2968                 return -EFAULT;
2969         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2970                  info->device_name, gpio.state, gpio.smask,
2971                  gpio.dir, gpio.dmask));
2972
2973         spin_lock_irqsave(&info->port_array[0]->lock, flags);
2974         if (gpio.dmask) {
2975                 data = rd_reg32(info, IODR);
2976                 data |= gpio.dmask & gpio.dir;
2977                 data &= ~(gpio.dmask & ~gpio.dir);
2978                 wr_reg32(info, IODR, data);
2979         }
2980         if (gpio.smask) {
2981                 data = rd_reg32(info, IOVR);
2982                 data |= gpio.smask & gpio.state;
2983                 data &= ~(gpio.smask & ~gpio.state);
2984                 wr_reg32(info, IOVR, data);
2985         }
2986         spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
2987
2988         return 0;
2989 }
2990
2991 /*
2992  * get general purpose IO pin state and direction
2993  */
2994 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2995 {
2996         struct gpio_desc gpio;
2997         if (!info->gpio_present)
2998                 return -EINVAL;
2999         gpio.state = rd_reg32(info, IOVR);
3000         gpio.smask = 0xffffffff;
3001         gpio.dir   = rd_reg32(info, IODR);
3002         gpio.dmask = 0xffffffff;
3003         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3004                 return -EFAULT;
3005         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
3006                  info->device_name, gpio.state, gpio.dir));
3007         return 0;
3008 }
3009
3010 /*
3011  * conditional wait facility
3012  */
3013 static void init_cond_wait(struct cond_wait *w, unsigned int data)
3014 {
3015         init_waitqueue_head(&w->q);
3016         init_waitqueue_entry(&w->wait, current);
3017         w->data = data;
3018 }
3019
3020 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
3021 {
3022         set_current_state(TASK_INTERRUPTIBLE);
3023         add_wait_queue(&w->q, &w->wait);
3024         w->next = *head;
3025         *head = w;
3026 }
3027
3028 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
3029 {
3030         struct cond_wait *w, *prev;
3031         remove_wait_queue(&cw->q, &cw->wait);
3032         set_current_state(TASK_RUNNING);
3033         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
3034                 if (w == cw) {
3035                         if (prev != NULL)
3036                                 prev->next = w->next;
3037                         else
3038                                 *head = w->next;
3039                         break;
3040                 }
3041         }
3042 }
3043
3044 static void flush_cond_wait(struct cond_wait **head)
3045 {
3046         while (*head != NULL) {
3047                 wake_up_interruptible(&(*head)->q);
3048                 *head = (*head)->next;
3049         }
3050 }
3051
3052 /*
3053  * wait for general purpose I/O pin(s) to enter specified state
3054  *
3055  * user_gpio fields:
3056  * state - bit indicates target pin state
3057  * smask - set bit indicates watched pin
3058  *
3059  * The wait ends when at least one watched pin enters the specified
3060  * state. When 0 (no error) is returned, user_gpio->state is set to the
3061  * state of all GPIO pins when the wait ends.
3062  *
3063  * Note: Each pin may be a dedicated input, dedicated output, or
3064  * configurable input/output. The number and configuration of pins
3065  * varies with the specific adapter model. Only input pins (dedicated
3066  * or configured) can be monitored with this function.
3067  */
3068 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3069 {
3070         unsigned long flags;
3071         int rc = 0;
3072         struct gpio_desc gpio;
3073         struct cond_wait wait;
3074         u32 state;
3075
3076         if (!info->gpio_present)
3077                 return -EINVAL;
3078         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
3079                 return -EFAULT;
3080         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
3081                  info->device_name, gpio.state, gpio.smask));
3082         /* ignore output pins identified by set IODR bit */
3083         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
3084                 return -EINVAL;
3085         init_cond_wait(&wait, gpio.smask);
3086
3087         spin_lock_irqsave(&info->port_array[0]->lock, flags);
3088         /* enable interrupts for watched pins */
3089         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3090         /* get current pin states */
3091         state = rd_reg32(info, IOVR);
3092
3093         if (gpio.smask & ~(state ^ gpio.state)) {
3094                 /* already in target state */
3095                 gpio.state = state;
3096         } else {
3097                 /* wait for target state */
3098                 add_cond_wait(&info->gpio_wait_q, &wait);
3099                 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3100                 schedule();
3101                 if (signal_pending(current))
3102                         rc = -ERESTARTSYS;
3103                 else
3104                         gpio.state = wait.data;
3105                 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3106                 remove_cond_wait(&info->gpio_wait_q, &wait);
3107         }
3108
3109         /* disable all GPIO interrupts if no waiting processes */
3110         if (info->gpio_wait_q == NULL)
3111                 wr_reg32(info, IOER, 0);
3112         spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3113
3114         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3115                 rc = -EFAULT;
3116         return rc;
3117 }
3118
3119 static int modem_input_wait(struct slgt_info *info,int arg)
3120 {
3121         unsigned long flags;
3122         int rc;
3123         struct mgsl_icount cprev, cnow;
3124         DECLARE_WAITQUEUE(wait, current);
3125
3126         /* save current irq counts */
3127         spin_lock_irqsave(&info->lock,flags);
3128         cprev = info->icount;
3129         add_wait_queue(&info->status_event_wait_q, &wait);
3130         set_current_state(TASK_INTERRUPTIBLE);
3131         spin_unlock_irqrestore(&info->lock,flags);
3132
3133         for(;;) {
3134                 schedule();
3135                 if (signal_pending(current)) {
3136                         rc = -ERESTARTSYS;
3137                         break;
3138                 }
3139
3140                 /* get new irq counts */
3141                 spin_lock_irqsave(&info->lock,flags);
3142                 cnow = info->icount;
3143                 set_current_state(TASK_INTERRUPTIBLE);
3144                 spin_unlock_irqrestore(&info->lock,flags);
3145
3146                 /* if no change, wait aborted for some reason */
3147                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3148                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3149                         rc = -EIO;
3150                         break;
3151                 }
3152
3153                 /* check for change in caller specified modem input */
3154                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3155                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3156                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
3157                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3158                         rc = 0;
3159                         break;
3160                 }
3161
3162                 cprev = cnow;
3163         }
3164         remove_wait_queue(&info->status_event_wait_q, &wait);
3165         set_current_state(TASK_RUNNING);
3166         return rc;
3167 }
3168
3169 /*
3170  *  return state of serial control and status signals
3171  */
3172 static int tiocmget(struct tty_struct *tty)
3173 {
3174         struct slgt_info *info = tty->driver_data;
3175         unsigned int result;
3176         unsigned long flags;
3177
3178         spin_lock_irqsave(&info->lock,flags);
3179         get_signals(info);
3180         spin_unlock_irqrestore(&info->lock,flags);
3181
3182         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3183                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3184                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3185                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
3186                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3187                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3188
3189         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3190         return result;
3191 }
3192
3193 /*
3194  * set modem control signals (DTR/RTS)
3195  *
3196  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3197  *              TIOCMSET = set/clear signal values
3198  *      value   bit mask for command
3199  */
3200 static int tiocmset(struct tty_struct *tty,
3201                     unsigned int set, unsigned int clear)
3202 {
3203         struct slgt_info *info = tty->driver_data;
3204         unsigned long flags;
3205
3206         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3207
3208         if (set & TIOCM_RTS)
3209                 info->signals |= SerialSignal_RTS;
3210         if (set & TIOCM_DTR)
3211                 info->signals |= SerialSignal_DTR;
3212         if (clear & TIOCM_RTS)
3213                 info->signals &= ~SerialSignal_RTS;
3214         if (clear & TIOCM_DTR)
3215                 info->signals &= ~SerialSignal_DTR;
3216
3217         spin_lock_irqsave(&info->lock,flags);
3218         set_signals(info);
3219         spin_unlock_irqrestore(&info->lock,flags);
3220         return 0;
3221 }
3222
3223 static int carrier_raised(struct tty_port *port)
3224 {
3225         unsigned long flags;
3226         struct slgt_info *info = container_of(port, struct slgt_info, port);
3227
3228         spin_lock_irqsave(&info->lock,flags);
3229         get_signals(info);
3230         spin_unlock_irqrestore(&info->lock,flags);
3231         return (info->signals & SerialSignal_DCD) ? 1 : 0;
3232 }
3233
3234 static void dtr_rts(struct tty_port *port, int on)
3235 {
3236         unsigned long flags;
3237         struct slgt_info *info = container_of(port, struct slgt_info, port);
3238
3239         spin_lock_irqsave(&info->lock,flags);
3240         if (on)
3241                 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
3242         else
3243                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3244         set_signals(info);
3245         spin_unlock_irqrestore(&info->lock,flags);
3246 }
3247
3248
3249 /*
3250  *  block current process until the device is ready to open
3251  */
3252 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3253                            struct slgt_info *info)
3254 {
3255         DECLARE_WAITQUEUE(wait, current);
3256         int             retval;
3257         bool            do_clocal = false;
3258         unsigned long   flags;
3259         int             cd;
3260         struct tty_port *port = &info->port;
3261
3262         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3263
3264         if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
3265                 /* nonblock mode is set or port is not enabled */
3266                 tty_port_set_active(port, 1);
3267                 return 0;
3268         }
3269
3270         if (C_CLOCAL(tty))
3271                 do_clocal = true;
3272
3273         /* Wait for carrier detect and the line to become
3274          * free (i.e., not in use by the callout).  While we are in
3275          * this loop, port->count is dropped by one, so that
3276          * close() knows when to free things.  We restore it upon
3277          * exit, either normal or abnormal.
3278          */
3279
3280         retval = 0;
3281         add_wait_queue(&port->open_wait, &wait);
3282
3283         spin_lock_irqsave(&info->lock, flags);
3284         port->count--;
3285         spin_unlock_irqrestore(&info->lock, flags);
3286         port->blocked_open++;
3287
3288         while (1) {
3289                 if (C_BAUD(tty) && tty_port_initialized(port))
3290                         tty_port_raise_dtr_rts(port);
3291
3292                 set_current_state(TASK_INTERRUPTIBLE);
3293
3294                 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
3295                         retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3296                                         -EAGAIN : -ERESTARTSYS;
3297                         break;
3298                 }
3299
3300                 cd = tty_port_carrier_raised(port);
3301                 if (do_clocal || cd)
3302                         break;
3303
3304                 if (signal_pending(current)) {
3305                         retval = -ERESTARTSYS;
3306                         break;
3307                 }
3308
3309                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3310                 tty_unlock(tty);
3311                 schedule();
3312                 tty_lock(tty);
3313         }
3314
3315         set_current_state(TASK_RUNNING);
3316         remove_wait_queue(&port->open_wait, &wait);
3317
3318         if (!tty_hung_up_p(filp))
3319                 port->count++;
3320         port->blocked_open--;
3321
3322         if (!retval)
3323                 tty_port_set_active(port, 1);
3324
3325         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3326         return retval;
3327 }
3328
3329 /*
3330  * allocate buffers used for calling line discipline receive_buf
3331  * directly in synchronous mode
3332  * note: add 5 bytes to max frame size to allow appending
3333  * 32-bit CRC and status byte when configured to do so
3334  */
3335 static int alloc_tmp_rbuf(struct slgt_info *info)
3336 {
3337         info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3338         if (info->tmp_rbuf == NULL)
3339                 return -ENOMEM;
3340         /* unused flag buffer to satisfy receive_buf calling interface */
3341         info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL);
3342         if (!info->flag_buf) {
3343                 kfree(info->tmp_rbuf);
3344                 info->tmp_rbuf = NULL;
3345                 return -ENOMEM;
3346         }
3347         return 0;
3348 }
3349
3350 static void free_tmp_rbuf(struct slgt_info *info)
3351 {
3352         kfree(info->tmp_rbuf);
3353         info->tmp_rbuf = NULL;
3354         kfree(info->flag_buf);
3355         info->flag_buf = NULL;
3356 }
3357
3358 /*
3359  * allocate DMA descriptor lists.
3360  */
3361 static int alloc_desc(struct slgt_info *info)
3362 {
3363         unsigned int i;
3364         unsigned int pbufs;
3365
3366         /* allocate memory to hold descriptor lists */
3367         info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE,
3368                                            &info->bufs_dma_addr);
3369         if (info->bufs == NULL)
3370                 return -ENOMEM;
3371
3372         info->rbufs = (struct slgt_desc*)info->bufs;
3373         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3374
3375         pbufs = (unsigned int)info->bufs_dma_addr;
3376
3377         /*
3378          * Build circular lists of descriptors
3379          */
3380
3381         for (i=0; i < info->rbuf_count; i++) {
3382                 /* physical address of this descriptor */
3383                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3384
3385                 /* physical address of next descriptor */
3386                 if (i == info->rbuf_count - 1)
3387                         info->rbufs[i].next = cpu_to_le32(pbufs);
3388                 else
3389                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3390                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3391         }
3392
3393         for (i=0; i < info->tbuf_count; i++) {
3394                 /* physical address of this descriptor */
3395                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3396
3397                 /* physical address of next descriptor */
3398                 if (i == info->tbuf_count - 1)
3399                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3400                 else
3401                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3402         }
3403
3404         return 0;
3405 }
3406
3407 static void free_desc(struct slgt_info *info)
3408 {
3409         if (info->bufs != NULL) {
3410                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3411                 info->bufs  = NULL;
3412                 info->rbufs = NULL;
3413                 info->tbufs = NULL;
3414         }
3415 }
3416
3417 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3418 {
3419         int i;
3420         for (i=0; i < count; i++) {
3421                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3422                         return -ENOMEM;
3423                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3424         }
3425         return 0;
3426 }
3427
3428 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3429 {
3430         int i;
3431         for (i=0; i < count; i++) {
3432                 if (bufs[i].buf == NULL)
3433                         continue;
3434                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3435                 bufs[i].buf = NULL;
3436         }
3437 }
3438
3439 static int alloc_dma_bufs(struct slgt_info *info)
3440 {
3441         info->rbuf_count = 32;
3442         info->tbuf_count = 32;
3443
3444         if (alloc_desc(info) < 0 ||
3445             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3446             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3447             alloc_tmp_rbuf(info) < 0) {
3448                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3449                 return -ENOMEM;
3450         }
3451         reset_rbufs(info);
3452         return 0;
3453 }
3454
3455 static void free_dma_bufs(struct slgt_info *info)
3456 {
3457         if (info->bufs) {
3458                 free_bufs(info, info->rbufs, info->rbuf_count);
3459                 free_bufs(info, info->tbufs, info->tbuf_count);
3460                 free_desc(info);
3461         }
3462         free_tmp_rbuf(info);
3463 }
3464
3465 static int claim_resources(struct slgt_info *info)
3466 {
3467         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3468                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3469                         info->device_name, info->phys_reg_addr));
3470                 info->init_error = DiagStatus_AddressConflict;
3471                 goto errout;
3472         }
3473         else
3474                 info->reg_addr_requested = true;
3475
3476         info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3477         if (!info->reg_addr) {
3478                 DBGERR(("%s can't map device registers, addr=%08X\n",
3479                         info->device_name, info->phys_reg_addr));
3480                 info->init_error = DiagStatus_CantAssignPciResources;
3481                 goto errout;
3482         }
3483         return 0;
3484
3485 errout:
3486         release_resources(info);
3487         return -ENODEV;
3488 }
3489
3490 static void release_resources(struct slgt_info *info)
3491 {
3492         if (info->irq_requested) {
3493                 free_irq(info->irq_level, info);
3494                 info->irq_requested = false;
3495         }
3496
3497         if (info->reg_addr_requested) {
3498                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3499                 info->reg_addr_requested = false;
3500         }
3501
3502         if (info->reg_addr) {
3503                 iounmap(info->reg_addr);
3504                 info->reg_addr = NULL;
3505         }
3506 }
3507
3508 /* Add the specified device instance data structure to the
3509  * global linked list of devices and increment the device count.
3510  */
3511 static void add_device(struct slgt_info *info)
3512 {
3513         char *devstr;
3514
3515         info->next_device = NULL;
3516         info->line = slgt_device_count;
3517         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3518
3519         if (info->line < MAX_DEVICES) {
3520                 if (maxframe[info->line])
3521                         info->max_frame_size = maxframe[info->line];
3522         }
3523
3524         slgt_device_count++;
3525
3526         if (!slgt_device_list)
3527                 slgt_device_list = info;
3528         else {
3529                 struct slgt_info *current_dev = slgt_device_list;
3530                 while(current_dev->next_device)
3531                         current_dev = current_dev->next_device;
3532                 current_dev->next_device = info;
3533         }
3534
3535         if (info->max_frame_size < 4096)
3536                 info->max_frame_size = 4096;
3537         else if (info->max_frame_size > 65535)
3538                 info->max_frame_size = 65535;
3539
3540         switch(info->pdev->device) {
3541         case SYNCLINK_GT_DEVICE_ID:
3542                 devstr = "GT";
3543                 break;
3544         case SYNCLINK_GT2_DEVICE_ID:
3545                 devstr = "GT2";
3546                 break;
3547         case SYNCLINK_GT4_DEVICE_ID:
3548                 devstr = "GT4";
3549                 break;
3550         case SYNCLINK_AC_DEVICE_ID:
3551                 devstr = "AC";
3552                 info->params.mode = MGSL_MODE_ASYNC;
3553                 break;
3554         default:
3555                 devstr = "(unknown model)";
3556         }
3557         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3558                 devstr, info->device_name, info->phys_reg_addr,
3559                 info->irq_level, info->max_frame_size);
3560
3561 #if SYNCLINK_GENERIC_HDLC
3562         hdlcdev_init(info);
3563 #endif
3564 }
3565
3566 static const struct tty_port_operations slgt_port_ops = {
3567         .carrier_raised = carrier_raised,
3568         .dtr_rts = dtr_rts,
3569 };
3570
3571 /*
3572  *  allocate device instance structure, return NULL on failure
3573  */
3574 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3575 {
3576         struct slgt_info *info;
3577
3578         info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3579
3580         if (!info) {
3581                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3582                         driver_name, adapter_num, port_num));
3583         } else {
3584                 tty_port_init(&info->port);
3585                 info->port.ops = &slgt_port_ops;
3586                 info->magic = MGSL_MAGIC;
3587                 INIT_WORK(&info->task, bh_handler);
3588                 info->max_frame_size = 4096;
3589                 info->base_clock = 14745600;
3590                 info->rbuf_fill_level = DMABUFSIZE;
3591                 info->port.close_delay = 5*HZ/10;
3592                 info->port.closing_wait = 30*HZ;
3593                 init_waitqueue_head(&info->status_event_wait_q);
3594                 init_waitqueue_head(&info->event_wait_q);
3595                 spin_lock_init(&info->netlock);
3596                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3597                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3598                 info->adapter_num = adapter_num;
3599                 info->port_num = port_num;
3600
3601                 setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3602                 setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3603
3604                 /* Copy configuration info to device instance data */
3605                 info->pdev = pdev;
3606                 info->irq_level = pdev->irq;
3607                 info->phys_reg_addr = pci_resource_start(pdev,0);
3608
3609                 info->bus_type = MGSL_BUS_TYPE_PCI;
3610                 info->irq_flags = IRQF_SHARED;
3611
3612                 info->init_error = -1; /* assume error, set to 0 on successful init */
3613         }
3614
3615         return info;
3616 }
3617
3618 static void device_init(int adapter_num, struct pci_dev *pdev)
3619 {
3620         struct slgt_info *port_array[SLGT_MAX_PORTS];
3621         int i;
3622         int port_count = 1;
3623
3624         if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3625                 port_count = 2;
3626         else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3627                 port_count = 4;
3628
3629         /* allocate device instances for all ports */
3630         for (i=0; i < port_count; ++i) {
3631                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3632                 if (port_array[i] == NULL) {
3633                         for (--i; i >= 0; --i) {
3634                                 tty_port_destroy(&port_array[i]->port);
3635                                 kfree(port_array[i]);
3636                         }
3637                         return;
3638                 }
3639         }
3640
3641         /* give copy of port_array to all ports and add to device list  */
3642         for (i=0; i < port_count; ++i) {
3643                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3644                 add_device(port_array[i]);
3645                 port_array[i]->port_count = port_count;
3646                 spin_lock_init(&port_array[i]->lock);
3647         }
3648
3649         /* Allocate and claim adapter resources */
3650         if (!claim_resources(port_array[0])) {
3651
3652                 alloc_dma_bufs(port_array[0]);
3653
3654                 /* copy resource information from first port to others */
3655                 for (i = 1; i < port_count; ++i) {
3656                         port_array[i]->irq_level = port_array[0]->irq_level;
3657                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3658                         alloc_dma_bufs(port_array[i]);
3659                 }
3660
3661                 if (request_irq(port_array[0]->irq_level,
3662                                         slgt_interrupt,
3663                                         port_array[0]->irq_flags,
3664                                         port_array[0]->device_name,
3665                                         port_array[0]) < 0) {
3666                         DBGERR(("%s request_irq failed IRQ=%d\n",
3667                                 port_array[0]->device_name,
3668                                 port_array[0]->irq_level));
3669                 } else {
3670                         port_array[0]->irq_requested = true;
3671                         adapter_test(port_array[0]);
3672                         for (i=1 ; i < port_count ; i++) {
3673                                 port_array[i]->init_error = port_array[0]->init_error;
3674                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3675                         }
3676                 }
3677         }
3678
3679         for (i = 0; i < port_count; ++i) {
3680                 struct slgt_info *info = port_array[i];
3681                 tty_port_register_device(&info->port, serial_driver, info->line,
3682                                 &info->pdev->dev);
3683         }
3684 }
3685
3686 static int init_one(struct pci_dev *dev,
3687                               const struct pci_device_id *ent)
3688 {
3689         if (pci_enable_device(dev)) {
3690                 printk("error enabling pci device %p\n", dev);
3691                 return -EIO;
3692         }
3693         pci_set_master(dev);
3694         device_init(slgt_device_count, dev);
3695         return 0;
3696 }
3697
3698 static void remove_one(struct pci_dev *dev)
3699 {
3700 }
3701
3702 static const struct tty_operations ops = {
3703         .open = open,
3704         .close = close,
3705         .write = write,
3706         .put_char = put_char,
3707         .flush_chars = flush_chars,
3708         .write_room = write_room,
3709         .chars_in_buffer = chars_in_buffer,
3710         .flush_buffer = flush_buffer,
3711         .ioctl = ioctl,
3712         .compat_ioctl = slgt_compat_ioctl,
3713         .throttle = throttle,
3714         .unthrottle = unthrottle,
3715         .send_xchar = send_xchar,
3716         .break_ctl = set_break,
3717         .wait_until_sent = wait_until_sent,
3718         .set_termios = set_termios,
3719         .stop = tx_hold,
3720         .start = tx_release,
3721         .hangup = hangup,
3722         .tiocmget = tiocmget,
3723         .tiocmset = tiocmset,
3724         .get_icount = get_icount,
3725         .proc_fops = &synclink_gt_proc_fops,
3726 };
3727
3728 static void slgt_cleanup(void)
3729 {
3730         int rc;
3731         struct slgt_info *info;
3732         struct slgt_info *tmp;
3733
3734         printk(KERN_INFO "unload %s\n", driver_name);
3735
3736         if (serial_driver) {
3737                 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3738                         tty_unregister_device(serial_driver, info->line);
3739                 rc = tty_unregister_driver(serial_driver);
3740                 if (rc)
3741                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3742                 put_tty_driver(serial_driver);
3743         }
3744
3745         /* reset devices */
3746         info = slgt_device_list;
3747         while(info) {
3748                 reset_port(info);
3749                 info = info->next_device;
3750         }
3751
3752         /* release devices */
3753         info = slgt_device_list;
3754         while(info) {
3755 #if SYNCLINK_GENERIC_HDLC
3756                 hdlcdev_exit(info);
3757 #endif
3758                 free_dma_bufs(info);
3759                 free_tmp_rbuf(info);
3760                 if (info->port_num == 0)
3761                         release_resources(info);
3762                 tmp = info;
3763                 info = info->next_device;
3764                 tty_port_destroy(&tmp->port);
3765                 kfree(tmp);
3766         }
3767
3768         if (pci_registered)
3769                 pci_unregister_driver(&pci_driver);
3770 }
3771
3772 /*
3773  *  Driver initialization entry point.
3774  */
3775 static int __init slgt_init(void)
3776 {
3777         int rc;
3778
3779         printk(KERN_INFO "%s\n", driver_name);
3780
3781         serial_driver = alloc_tty_driver(MAX_DEVICES);
3782         if (!serial_driver) {
3783                 printk("%s can't allocate tty driver\n", driver_name);
3784                 return -ENOMEM;
3785         }
3786
3787         /* Initialize the tty_driver structure */
3788
3789         serial_driver->driver_name = slgt_driver_name;
3790         serial_driver->name = tty_dev_prefix;
3791         serial_driver->major = ttymajor;
3792         serial_driver->minor_start = 64;
3793         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3794         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3795         serial_driver->init_termios = tty_std_termios;
3796         serial_driver->init_termios.c_cflag =
3797                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3798         serial_driver->init_termios.c_ispeed = 9600;
3799         serial_driver->init_termios.c_ospeed = 9600;
3800         serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3801         tty_set_operations(serial_driver, &ops);
3802         if ((rc = tty_register_driver(serial_driver)) < 0) {
3803                 DBGERR(("%s can't register serial driver\n", driver_name));
3804                 put_tty_driver(serial_driver);
3805                 serial_driver = NULL;
3806                 goto error;
3807         }
3808
3809         printk(KERN_INFO "%s, tty major#%d\n",
3810                driver_name, serial_driver->major);
3811
3812         slgt_device_count = 0;
3813         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3814                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3815                 goto error;
3816         }
3817         pci_registered = true;
3818
3819         if (!slgt_device_list)
3820                 printk("%s no devices found\n",driver_name);
3821
3822         return 0;
3823
3824 error:
3825         slgt_cleanup();
3826         return rc;
3827 }
3828
3829 static void __exit slgt_exit(void)
3830 {
3831         slgt_cleanup();
3832 }
3833
3834 module_init(slgt_init);
3835 module_exit(slgt_exit);
3836
3837 /*
3838  * register access routines
3839  */
3840
3841 #define CALC_REGADDR() \
3842         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3843         if (addr >= 0x80) \
3844                 reg_addr += (info->port_num) * 32; \
3845         else if (addr >= 0x40)  \
3846                 reg_addr += (info->port_num) * 16;
3847
3848 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3849 {
3850         CALC_REGADDR();
3851         return readb((void __iomem *)reg_addr);
3852 }
3853
3854 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3855 {
3856         CALC_REGADDR();
3857         writeb(value, (void __iomem *)reg_addr);
3858 }
3859
3860 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3861 {
3862         CALC_REGADDR();
3863         return readw((void __iomem *)reg_addr);
3864 }
3865
3866 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3867 {
3868         CALC_REGADDR();
3869         writew(value, (void __iomem *)reg_addr);
3870 }
3871
3872 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3873 {
3874         CALC_REGADDR();
3875         return readl((void __iomem *)reg_addr);
3876 }
3877
3878 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3879 {
3880         CALC_REGADDR();
3881         writel(value, (void __iomem *)reg_addr);
3882 }
3883
3884 static void rdma_reset(struct slgt_info *info)
3885 {
3886         unsigned int i;
3887
3888         /* set reset bit */
3889         wr_reg32(info, RDCSR, BIT1);
3890
3891         /* wait for enable bit cleared */
3892         for(i=0 ; i < 1000 ; i++)
3893                 if (!(rd_reg32(info, RDCSR) & BIT0))
3894                         break;
3895 }
3896
3897 static void tdma_reset(struct slgt_info *info)
3898 {
3899         unsigned int i;
3900
3901         /* set reset bit */
3902         wr_reg32(info, TDCSR, BIT1);
3903
3904         /* wait for enable bit cleared */
3905         for(i=0 ; i < 1000 ; i++)
3906                 if (!(rd_reg32(info, TDCSR) & BIT0))
3907                         break;
3908 }
3909
3910 /*
3911  * enable internal loopback
3912  * TxCLK and RxCLK are generated from BRG
3913  * and TxD is looped back to RxD internally.
3914  */
3915 static void enable_loopback(struct slgt_info *info)
3916 {
3917         /* SCR (serial control) BIT2=loopback enable */
3918         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3919
3920         if (info->params.mode != MGSL_MODE_ASYNC) {
3921                 /* CCR (clock control)
3922                  * 07..05  tx clock source (010 = BRG)
3923                  * 04..02  rx clock source (010 = BRG)
3924                  * 01      auxclk enable   (0 = disable)
3925                  * 00      BRG enable      (1 = enable)
3926                  *
3927                  * 0100 1001
3928                  */
3929                 wr_reg8(info, CCR, 0x49);
3930
3931                 /* set speed if available, otherwise use default */
3932                 if (info->params.clock_speed)
3933                         set_rate(info, info->params.clock_speed);
3934                 else
3935                         set_rate(info, 3686400);
3936         }
3937 }
3938
3939 /*
3940  *  set baud rate generator to specified rate
3941  */
3942 static void set_rate(struct slgt_info *info, u32 rate)
3943 {
3944         unsigned int div;
3945         unsigned int osc = info->base_clock;
3946
3947         /* div = osc/rate - 1
3948          *
3949          * Round div up if osc/rate is not integer to
3950          * force to next slowest rate.
3951          */
3952
3953         if (rate) {
3954                 div = osc/rate;
3955                 if (!(osc % rate) && div)
3956                         div--;
3957                 wr_reg16(info, BDR, (unsigned short)div);
3958         }
3959 }
3960
3961 static void rx_stop(struct slgt_info *info)
3962 {
3963         unsigned short val;
3964
3965         /* disable and reset receiver */
3966         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3967         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3968         wr_reg16(info, RCR, val);                  /* clear reset bit */
3969
3970         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3971
3972         /* clear pending rx interrupts */
3973         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3974
3975         rdma_reset(info);
3976
3977         info->rx_enabled = false;
3978         info->rx_restart = false;
3979 }
3980
3981 static void rx_start(struct slgt_info *info)
3982 {
3983         unsigned short val;
3984
3985         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3986
3987         /* clear pending rx overrun IRQ */
3988         wr_reg16(info, SSR, IRQ_RXOVER);
3989
3990         /* reset and disable receiver */
3991         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3992         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3993         wr_reg16(info, RCR, val);                  /* clear reset bit */
3994
3995         rdma_reset(info);
3996         reset_rbufs(info);
3997
3998         if (info->rx_pio) {
3999                 /* rx request when rx FIFO not empty */
4000                 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
4001                 slgt_irq_on(info, IRQ_RXDATA);
4002                 if (info->params.mode == MGSL_MODE_ASYNC) {
4003                         /* enable saving of rx status */
4004                         wr_reg32(info, RDCSR, BIT6);
4005                 }
4006         } else {
4007                 /* rx request when rx FIFO half full */
4008                 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
4009                 /* set 1st descriptor address */
4010                 wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
4011
4012                 if (info->params.mode != MGSL_MODE_ASYNC) {
4013                         /* enable rx DMA and DMA interrupt */
4014                         wr_reg32(info, RDCSR, (BIT2 + BIT0));
4015                 } else {
4016                         /* enable saving of rx status, rx DMA and DMA interrupt */
4017                         wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
4018                 }
4019         }
4020
4021         slgt_irq_on(info, IRQ_RXOVER);
4022
4023         /* enable receiver */
4024         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
4025
4026         info->rx_restart = false;
4027         info->rx_enabled = true;
4028 }
4029
4030 static void tx_start(struct slgt_info *info)
4031 {
4032         if (!info->tx_enabled) {
4033                 wr_reg16(info, TCR,
4034                          (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
4035                 info->tx_enabled = true;
4036         }
4037
4038         if (desc_count(info->tbufs[info->tbuf_start])) {
4039                 info->drop_rts_on_tx_done = false;
4040
4041                 if (info->params.mode != MGSL_MODE_ASYNC) {
4042                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
4043                                 get_signals(info);
4044                                 if (!(info->signals & SerialSignal_RTS)) {
4045                                         info->signals |= SerialSignal_RTS;
4046                                         set_signals(info);
4047                                         info->drop_rts_on_tx_done = true;
4048                                 }
4049                         }
4050
4051                         slgt_irq_off(info, IRQ_TXDATA);
4052                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
4053                         /* clear tx idle and underrun status bits */
4054                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4055                 } else {
4056                         slgt_irq_off(info, IRQ_TXDATA);
4057                         slgt_irq_on(info, IRQ_TXIDLE);
4058                         /* clear tx idle status bit */
4059                         wr_reg16(info, SSR, IRQ_TXIDLE);
4060                 }
4061                 /* set 1st descriptor address and start DMA */
4062                 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
4063                 wr_reg32(info, TDCSR, BIT2 + BIT0);
4064                 info->tx_active = true;
4065         }
4066 }
4067
4068 static void tx_stop(struct slgt_info *info)
4069 {
4070         unsigned short val;
4071
4072         del_timer(&info->tx_timer);
4073
4074         tdma_reset(info);
4075
4076         /* reset and disable transmitter */
4077         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
4078         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
4079
4080         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
4081
4082         /* clear tx idle and underrun status bit */
4083         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4084
4085         reset_tbufs(info);
4086
4087         info->tx_enabled = false;
4088         info->tx_active = false;
4089 }
4090
4091 static void reset_port(struct slgt_info *info)
4092 {
4093         if (!info->reg_addr)
4094                 return;
4095
4096         tx_stop(info);
4097         rx_stop(info);
4098
4099         info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
4100         set_signals(info);
4101
4102         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4103 }
4104
4105 static void reset_adapter(struct slgt_info *info)
4106 {
4107         int i;
4108         for (i=0; i < info->port_count; ++i) {
4109                 if (info->port_array[i])
4110                         reset_port(info->port_array[i]);
4111         }
4112 }
4113
4114 static void async_mode(struct slgt_info *info)
4115 {
4116         unsigned short val;
4117
4118         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4119         tx_stop(info);
4120         rx_stop(info);
4121
4122         /* TCR (tx control)
4123          *
4124          * 15..13  mode, 010=async
4125          * 12..10  encoding, 000=NRZ
4126          * 09      parity enable
4127          * 08      1=odd parity, 0=even parity
4128          * 07      1=RTS driver control
4129          * 06      1=break enable
4130          * 05..04  character length
4131          *         00=5 bits
4132          *         01=6 bits
4133          *         10=7 bits
4134          *         11=8 bits
4135          * 03      0=1 stop bit, 1=2 stop bits
4136          * 02      reset
4137          * 01      enable
4138          * 00      auto-CTS enable
4139          */
4140         val = 0x4000;
4141
4142         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4143                 val |= BIT7;
4144
4145         if (info->params.parity != ASYNC_PARITY_NONE) {
4146                 val |= BIT9;
4147                 if (info->params.parity == ASYNC_PARITY_ODD)
4148                         val |= BIT8;
4149         }
4150
4151         switch (info->params.data_bits)
4152         {
4153         case 6: val |= BIT4; break;
4154         case 7: val |= BIT5; break;
4155         case 8: val |= BIT5 + BIT4; break;
4156         }
4157
4158         if (info->params.stop_bits != 1)
4159                 val |= BIT3;
4160
4161         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4162                 val |= BIT0;
4163
4164         wr_reg16(info, TCR, val);
4165
4166         /* RCR (rx control)
4167          *
4168          * 15..13  mode, 010=async
4169          * 12..10  encoding, 000=NRZ
4170          * 09      parity enable
4171          * 08      1=odd parity, 0=even parity
4172          * 07..06  reserved, must be 0
4173          * 05..04  character length
4174          *         00=5 bits
4175          *         01=6 bits
4176          *         10=7 bits
4177          *         11=8 bits
4178          * 03      reserved, must be zero
4179          * 02      reset
4180          * 01      enable
4181          * 00      auto-DCD enable
4182          */
4183         val = 0x4000;
4184
4185         if (info->params.parity != ASYNC_PARITY_NONE) {
4186                 val |= BIT9;
4187                 if (info->params.parity == ASYNC_PARITY_ODD)
4188                         val |= BIT8;
4189         }
4190
4191         switch (info->params.data_bits)
4192         {
4193         case 6: val |= BIT4; break;
4194         case 7: val |= BIT5; break;
4195         case 8: val |= BIT5 + BIT4; break;
4196         }
4197
4198         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4199                 val |= BIT0;
4200
4201         wr_reg16(info, RCR, val);
4202
4203         /* CCR (clock control)
4204          *
4205          * 07..05  011 = tx clock source is BRG/16
4206          * 04..02  010 = rx clock source is BRG
4207          * 01      0 = auxclk disabled
4208          * 00      1 = BRG enabled
4209          *
4210          * 0110 1001
4211          */
4212         wr_reg8(info, CCR, 0x69);
4213
4214         msc_set_vcr(info);
4215
4216         /* SCR (serial control)
4217          *
4218          * 15  1=tx req on FIFO half empty
4219          * 14  1=rx req on FIFO half full
4220          * 13  tx data  IRQ enable
4221          * 12  tx idle  IRQ enable
4222          * 11  rx break on IRQ enable
4223          * 10  rx data  IRQ enable
4224          * 09  rx break off IRQ enable
4225          * 08  overrun  IRQ enable
4226          * 07  DSR      IRQ enable
4227          * 06  CTS      IRQ enable
4228          * 05  DCD      IRQ enable
4229          * 04  RI       IRQ enable
4230          * 03  0=16x sampling, 1=8x sampling
4231          * 02  1=txd->rxd internal loopback enable
4232          * 01  reserved, must be zero
4233          * 00  1=master IRQ enable
4234          */
4235         val = BIT15 + BIT14 + BIT0;
4236         /* JCR[8] : 1 = x8 async mode feature available */
4237         if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4238             ((info->base_clock < (info->params.data_rate * 16)) ||
4239              (info->base_clock % (info->params.data_rate * 16)))) {
4240                 /* use 8x sampling */
4241                 val |= BIT3;
4242                 set_rate(info, info->params.data_rate * 8);
4243         } else {
4244                 /* use 16x sampling */
4245                 set_rate(info, info->params.data_rate * 16);
4246         }
4247         wr_reg16(info, SCR, val);
4248
4249         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4250
4251         if (info->params.loopback)
4252                 enable_loopback(info);
4253 }
4254
4255 static void sync_mode(struct slgt_info *info)
4256 {
4257         unsigned short val;
4258
4259         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4260         tx_stop(info);
4261         rx_stop(info);
4262
4263         /* TCR (tx control)
4264          *
4265          * 15..13  mode
4266          *         000=HDLC/SDLC
4267          *         001=raw bit synchronous
4268          *         010=asynchronous/isochronous
4269          *         011=monosync byte synchronous
4270          *         100=bisync byte synchronous
4271          *         101=xsync byte synchronous
4272          * 12..10  encoding
4273          * 09      CRC enable
4274          * 08      CRC32
4275          * 07      1=RTS driver control
4276          * 06      preamble enable
4277          * 05..04  preamble length
4278          * 03      share open/close flag
4279          * 02      reset
4280          * 01      enable
4281          * 00      auto-CTS enable
4282          */
4283         val = BIT2;
4284
4285         switch(info->params.mode) {
4286         case MGSL_MODE_XSYNC:
4287                 val |= BIT15 + BIT13;
4288                 break;
4289         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4290         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4291         case MGSL_MODE_RAW:      val |= BIT13; break;
4292         }
4293         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4294                 val |= BIT7;
4295
4296         switch(info->params.encoding)
4297         {
4298         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4299         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4300         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4301         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4302         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4303         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4304         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4305         }
4306
4307         switch (info->params.crc_type & HDLC_CRC_MASK)
4308         {
4309         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4310         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4311         }
4312
4313         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4314                 val |= BIT6;
4315
4316         switch (info->params.preamble_length)
4317         {
4318         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4319         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4320         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4321         }
4322
4323         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4324                 val |= BIT0;
4325
4326         wr_reg16(info, TCR, val);
4327
4328         /* TPR (transmit preamble) */
4329
4330         switch (info->params.preamble)
4331         {
4332         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4333         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4334         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4335         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4336         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4337         default:                          val = 0x7e; break;
4338         }
4339         wr_reg8(info, TPR, (unsigned char)val);
4340
4341         /* RCR (rx control)
4342          *
4343          * 15..13  mode
4344          *         000=HDLC/SDLC
4345          *         001=raw bit synchronous
4346          *         010=asynchronous/isochronous
4347          *         011=monosync byte synchronous
4348          *         100=bisync byte synchronous
4349          *         101=xsync byte synchronous
4350          * 12..10  encoding
4351          * 09      CRC enable
4352          * 08      CRC32
4353          * 07..03  reserved, must be 0
4354          * 02      reset
4355          * 01      enable
4356          * 00      auto-DCD enable
4357          */
4358         val = 0;
4359
4360         switch(info->params.mode) {
4361         case MGSL_MODE_XSYNC:
4362                 val |= BIT15 + BIT13;
4363                 break;
4364         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4365         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4366         case MGSL_MODE_RAW:      val |= BIT13; break;
4367         }
4368
4369         switch(info->params.encoding)
4370         {
4371         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4372         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4373         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4374         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4375         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4376         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4377         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4378         }
4379
4380         switch (info->params.crc_type & HDLC_CRC_MASK)
4381         {
4382         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4383         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4384         }
4385
4386         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4387                 val |= BIT0;
4388
4389         wr_reg16(info, RCR, val);
4390
4391         /* CCR (clock control)
4392          *
4393          * 07..05  tx clock source
4394          * 04..02  rx clock source
4395          * 01      auxclk enable
4396          * 00      BRG enable
4397          */
4398         val = 0;
4399
4400         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4401         {
4402                 // when RxC source is DPLL, BRG generates 16X DPLL
4403                 // reference clock, so take TxC from BRG/16 to get
4404                 // transmit clock at actual data rate
4405                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4406                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4407                 else
4408                         val |= BIT6;    /* 010, txclk = BRG */
4409         }
4410         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4411                 val |= BIT7;    /* 100, txclk = DPLL Input */
4412         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4413                 val |= BIT5;    /* 001, txclk = RXC Input */
4414
4415         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4416                 val |= BIT3;    /* 010, rxclk = BRG */
4417         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4418                 val |= BIT4;    /* 100, rxclk = DPLL */
4419         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4420                 val |= BIT2;    /* 001, rxclk = TXC Input */
4421
4422         if (info->params.clock_speed)
4423                 val |= BIT1 + BIT0;
4424
4425         wr_reg8(info, CCR, (unsigned char)val);
4426
4427         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4428         {
4429                 // program DPLL mode
4430                 switch(info->params.encoding)
4431                 {
4432                 case HDLC_ENCODING_BIPHASE_MARK:
4433                 case HDLC_ENCODING_BIPHASE_SPACE:
4434                         val = BIT7; break;
4435                 case HDLC_ENCODING_BIPHASE_LEVEL:
4436                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4437                         val = BIT7 + BIT6; break;
4438                 default: val = BIT6;    // NRZ encodings
4439                 }
4440                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4441
4442                 // DPLL requires a 16X reference clock from BRG
4443                 set_rate(info, info->params.clock_speed * 16);
4444         }
4445         else
4446                 set_rate(info, info->params.clock_speed);
4447
4448         tx_set_idle(info);
4449
4450         msc_set_vcr(info);
4451
4452         /* SCR (serial control)
4453          *
4454          * 15  1=tx req on FIFO half empty
4455          * 14  1=rx req on FIFO half full
4456          * 13  tx data  IRQ enable
4457          * 12  tx idle  IRQ enable
4458          * 11  underrun IRQ enable
4459          * 10  rx data  IRQ enable
4460          * 09  rx idle  IRQ enable
4461          * 08  overrun  IRQ enable
4462          * 07  DSR      IRQ enable
4463          * 06  CTS      IRQ enable
4464          * 05  DCD      IRQ enable
4465          * 04  RI       IRQ enable
4466          * 03  reserved, must be zero
4467          * 02  1=txd->rxd internal loopback enable
4468          * 01  reserved, must be zero
4469          * 00  1=master IRQ enable
4470          */
4471         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4472
4473         if (info->params.loopback)
4474                 enable_loopback(info);
4475 }
4476
4477 /*
4478  *  set transmit idle mode
4479  */
4480 static void tx_set_idle(struct slgt_info *info)
4481 {
4482         unsigned char val;
4483         unsigned short tcr;
4484
4485         /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4486          * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4487          */
4488         tcr = rd_reg16(info, TCR);
4489         if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4490                 /* disable preamble, set idle size to 16 bits */
4491                 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4492                 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4493                 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4494         } else if (!(tcr & BIT6)) {
4495                 /* preamble is disabled, set idle size to 8 bits */
4496                 tcr &= ~(BIT5 + BIT4);
4497         }
4498         wr_reg16(info, TCR, tcr);
4499
4500         if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4501                 /* LSB of custom tx idle specified in tx idle register */
4502                 val = (unsigned char)(info->idle_mode & 0xff);
4503         } else {
4504                 /* standard 8 bit idle patterns */
4505                 switch(info->idle_mode)
4506                 {
4507                 case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4508                 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4509                 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4510                 case HDLC_TXIDLE_ZEROS:
4511                 case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4512                 default:                         val = 0xff;
4513                 }
4514         }
4515
4516         wr_reg8(info, TIR, val);
4517 }
4518
4519 /*
4520  * get state of V24 status (input) signals
4521  */
4522 static void get_signals(struct slgt_info *info)
4523 {
4524         unsigned short status = rd_reg16(info, SSR);
4525
4526         /* clear all serial signals except RTS and DTR */
4527         info->signals &= SerialSignal_RTS | SerialSignal_DTR;
4528
4529         if (status & BIT3)
4530                 info->signals |= SerialSignal_DSR;
4531         if (status & BIT2)
4532                 info->signals |= SerialSignal_CTS;
4533         if (status & BIT1)
4534                 info->signals |= SerialSignal_DCD;
4535         if (status & BIT0)
4536                 info->signals |= SerialSignal_RI;
4537 }
4538
4539 /*
4540  * set V.24 Control Register based on current configuration
4541  */
4542 static void msc_set_vcr(struct slgt_info *info)
4543 {
4544         unsigned char val = 0;
4545
4546         /* VCR (V.24 control)
4547          *
4548          * 07..04  serial IF select
4549          * 03      DTR
4550          * 02      RTS
4551          * 01      LL
4552          * 00      RL
4553          */
4554
4555         switch(info->if_mode & MGSL_INTERFACE_MASK)
4556         {
4557         case MGSL_INTERFACE_RS232:
4558                 val |= BIT5; /* 0010 */
4559                 break;
4560         case MGSL_INTERFACE_V35:
4561                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4562                 break;
4563         case MGSL_INTERFACE_RS422:
4564                 val |= BIT6; /* 0100 */
4565                 break;
4566         }
4567
4568         if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4569                 val |= BIT4;
4570         if (info->signals & SerialSignal_DTR)
4571                 val |= BIT3;
4572         if (info->signals & SerialSignal_RTS)
4573                 val |= BIT2;
4574         if (info->if_mode & MGSL_INTERFACE_LL)
4575                 val |= BIT1;
4576         if (info->if_mode & MGSL_INTERFACE_RL)
4577                 val |= BIT0;
4578         wr_reg8(info, VCR, val);
4579 }
4580
4581 /*
4582  * set state of V24 control (output) signals
4583  */
4584 static void set_signals(struct slgt_info *info)
4585 {
4586         unsigned char val = rd_reg8(info, VCR);
4587         if (info->signals & SerialSignal_DTR)
4588                 val |= BIT3;
4589         else
4590                 val &= ~BIT3;
4591         if (info->signals & SerialSignal_RTS)
4592                 val |= BIT2;
4593         else
4594                 val &= ~BIT2;
4595         wr_reg8(info, VCR, val);
4596 }
4597
4598 /*
4599  * free range of receive DMA buffers (i to last)
4600  */
4601 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4602 {
4603         int done = 0;
4604
4605         while(!done) {
4606                 /* reset current buffer for reuse */
4607                 info->rbufs[i].status = 0;
4608                 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4609                 if (i == last)
4610                         done = 1;
4611                 if (++i == info->rbuf_count)
4612                         i = 0;
4613         }
4614         info->rbuf_current = i;
4615 }
4616
4617 /*
4618  * mark all receive DMA buffers as free
4619  */
4620 static void reset_rbufs(struct slgt_info *info)
4621 {
4622         free_rbufs(info, 0, info->rbuf_count - 1);
4623         info->rbuf_fill_index = 0;
4624         info->rbuf_fill_count = 0;
4625 }
4626
4627 /*
4628  * pass receive HDLC frame to upper layer
4629  *
4630  * return true if frame available, otherwise false
4631  */
4632 static bool rx_get_frame(struct slgt_info *info)
4633 {
4634         unsigned int start, end;
4635         unsigned short status;
4636         unsigned int framesize = 0;
4637         unsigned long flags;
4638         struct tty_struct *tty = info->port.tty;
4639         unsigned char addr_field = 0xff;
4640         unsigned int crc_size = 0;
4641
4642         switch (info->params.crc_type & HDLC_CRC_MASK) {
4643         case HDLC_CRC_16_CCITT: crc_size = 2; break;
4644         case HDLC_CRC_32_CCITT: crc_size = 4; break;
4645         }
4646
4647 check_again:
4648
4649         framesize = 0;
4650         addr_field = 0xff;
4651         start = end = info->rbuf_current;
4652
4653         for (;;) {
4654                 if (!desc_complete(info->rbufs[end]))
4655                         goto cleanup;
4656
4657                 if (framesize == 0 && info->params.addr_filter != 0xff)
4658                         addr_field = info->rbufs[end].buf[0];
4659
4660                 framesize += desc_count(info->rbufs[end]);
4661
4662                 if (desc_eof(info->rbufs[end]))
4663                         break;
4664
4665                 if (++end == info->rbuf_count)
4666                         end = 0;
4667
4668                 if (end == info->rbuf_current) {
4669                         if (info->rx_enabled){
4670                                 spin_lock_irqsave(&info->lock,flags);
4671                                 rx_start(info);
4672                                 spin_unlock_irqrestore(&info->lock,flags);
4673                         }
4674                         goto cleanup;
4675                 }
4676         }
4677
4678         /* status
4679          *
4680          * 15      buffer complete
4681          * 14..06  reserved
4682          * 05..04  residue
4683          * 02      eof (end of frame)
4684          * 01      CRC error
4685          * 00      abort
4686          */
4687         status = desc_status(info->rbufs[end]);
4688
4689         /* ignore CRC bit if not using CRC (bit is undefined) */
4690         if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4691                 status &= ~BIT1;
4692
4693         if (framesize == 0 ||
4694                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4695                 free_rbufs(info, start, end);
4696                 goto check_again;
4697         }
4698
4699         if (framesize < (2 + crc_size) || status & BIT0) {
4700                 info->icount.rxshort++;
4701                 framesize = 0;
4702         } else if (status & BIT1) {
4703                 info->icount.rxcrc++;
4704                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4705                         framesize = 0;
4706         }
4707
4708 #if SYNCLINK_GENERIC_HDLC
4709         if (framesize == 0) {
4710                 info->netdev->stats.rx_errors++;
4711                 info->netdev->stats.rx_frame_errors++;
4712         }
4713 #endif
4714
4715         DBGBH(("%s rx frame status=%04X size=%d\n",
4716                 info->device_name, status, framesize));
4717         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4718
4719         if (framesize) {
4720                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4721                         framesize -= crc_size;
4722                         crc_size = 0;
4723                 }
4724
4725                 if (framesize > info->max_frame_size + crc_size)
4726                         info->icount.rxlong++;
4727                 else {
4728                         /* copy dma buffer(s) to contiguous temp buffer */
4729                         int copy_count = framesize;
4730                         int i = start;
4731                         unsigned char *p = info->tmp_rbuf;
4732                         info->tmp_rbuf_count = framesize;
4733
4734                         info->icount.rxok++;
4735
4736                         while(copy_count) {
4737                                 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4738                                 memcpy(p, info->rbufs[i].buf, partial_count);
4739                                 p += partial_count;
4740                                 copy_count -= partial_count;
4741                                 if (++i == info->rbuf_count)
4742                                         i = 0;
4743                         }
4744
4745                         if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4746                                 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4747                                 framesize++;
4748                         }
4749
4750 #if SYNCLINK_GENERIC_HDLC
4751                         if (info->netcount)
4752                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4753                         else
4754 #endif
4755                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4756                 }
4757         }
4758         free_rbufs(info, start, end);
4759         return true;
4760
4761 cleanup:
4762         return false;
4763 }
4764
4765 /*
4766  * pass receive buffer (RAW synchronous mode) to tty layer
4767  * return true if buffer available, otherwise false
4768  */
4769 static bool rx_get_buf(struct slgt_info *info)
4770 {
4771         unsigned int i = info->rbuf_current;
4772         unsigned int count;
4773
4774         if (!desc_complete(info->rbufs[i]))
4775                 return false;
4776         count = desc_count(info->rbufs[i]);
4777         switch(info->params.mode) {
4778         case MGSL_MODE_MONOSYNC:
4779         case MGSL_MODE_BISYNC:
4780         case MGSL_MODE_XSYNC:
4781                 /* ignore residue in byte synchronous modes */
4782                 if (desc_residue(info->rbufs[i]))
4783                         count--;
4784                 break;
4785         }
4786         DBGDATA(info, info->rbufs[i].buf, count, "rx");
4787         DBGINFO(("rx_get_buf size=%d\n", count));
4788         if (count)
4789                 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4790                                   info->flag_buf, count);
4791         free_rbufs(info, i, i);
4792         return true;
4793 }
4794
4795 static void reset_tbufs(struct slgt_info *info)
4796 {
4797         unsigned int i;
4798         info->tbuf_current = 0;
4799         for (i=0 ; i < info->tbuf_count ; i++) {
4800                 info->tbufs[i].status = 0;
4801                 info->tbufs[i].count  = 0;
4802         }
4803 }
4804
4805 /*
4806  * return number of free transmit DMA buffers
4807  */
4808 static unsigned int free_tbuf_count(struct slgt_info *info)
4809 {
4810         unsigned int count = 0;
4811         unsigned int i = info->tbuf_current;
4812
4813         do
4814         {
4815                 if (desc_count(info->tbufs[i]))
4816                         break; /* buffer in use */
4817                 ++count;
4818                 if (++i == info->tbuf_count)
4819                         i=0;
4820         } while (i != info->tbuf_current);
4821
4822         /* if tx DMA active, last zero count buffer is in use */
4823         if (count && (rd_reg32(info, TDCSR) & BIT0))
4824                 --count;
4825
4826         return count;
4827 }
4828
4829 /*
4830  * return number of bytes in unsent transmit DMA buffers
4831  * and the serial controller tx FIFO
4832  */
4833 static unsigned int tbuf_bytes(struct slgt_info *info)
4834 {
4835         unsigned int total_count = 0;
4836         unsigned int i = info->tbuf_current;
4837         unsigned int reg_value;
4838         unsigned int count;
4839         unsigned int active_buf_count = 0;
4840
4841         /*
4842          * Add descriptor counts for all tx DMA buffers.
4843          * If count is zero (cleared by DMA controller after read),
4844          * the buffer is complete or is actively being read from.
4845          *
4846          * Record buf_count of last buffer with zero count starting
4847          * from current ring position. buf_count is mirror
4848          * copy of count and is not cleared by serial controller.
4849          * If DMA controller is active, that buffer is actively
4850          * being read so add to total.
4851          */
4852         do {
4853                 count = desc_count(info->tbufs[i]);
4854                 if (count)
4855                         total_count += count;
4856                 else if (!total_count)
4857                         active_buf_count = info->tbufs[i].buf_count;
4858                 if (++i == info->tbuf_count)
4859                         i = 0;
4860         } while (i != info->tbuf_current);
4861
4862         /* read tx DMA status register */
4863         reg_value = rd_reg32(info, TDCSR);
4864
4865         /* if tx DMA active, last zero count buffer is in use */
4866         if (reg_value & BIT0)
4867                 total_count += active_buf_count;
4868
4869         /* add tx FIFO count = reg_value[15..8] */
4870         total_count += (reg_value >> 8) & 0xff;
4871
4872         /* if transmitter active add one byte for shift register */
4873         if (info->tx_active)
4874                 total_count++;
4875
4876         return total_count;
4877 }
4878
4879 /*
4880  * load data into transmit DMA buffer ring and start transmitter if needed
4881  * return true if data accepted, otherwise false (buffers full)
4882  */
4883 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4884 {
4885         unsigned short count;
4886         unsigned int i;
4887         struct slgt_desc *d;
4888
4889         /* check required buffer space */
4890         if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4891                 return false;
4892
4893         DBGDATA(info, buf, size, "tx");
4894
4895         /*
4896          * copy data to one or more DMA buffers in circular ring
4897          * tbuf_start   = first buffer for this data
4898          * tbuf_current = next free buffer
4899          *
4900          * Copy all data before making data visible to DMA controller by
4901          * setting descriptor count of the first buffer.
4902          * This prevents an active DMA controller from reading the first DMA
4903          * buffers of a frame and stopping before the final buffers are filled.
4904          */
4905
4906         info->tbuf_start = i = info->tbuf_current;
4907
4908         while (size) {
4909                 d = &info->tbufs[i];
4910
4911                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4912                 memcpy(d->buf, buf, count);
4913
4914                 size -= count;
4915                 buf  += count;
4916
4917                 /*
4918                  * set EOF bit for last buffer of HDLC frame or
4919                  * for every buffer in raw mode
4920                  */
4921                 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4922                     info->params.mode == MGSL_MODE_RAW)
4923                         set_desc_eof(*d, 1);
4924                 else
4925                         set_desc_eof(*d, 0);
4926
4927                 /* set descriptor count for all but first buffer */
4928                 if (i != info->tbuf_start)
4929                         set_desc_count(*d, count);
4930                 d->buf_count = count;
4931
4932                 if (++i == info->tbuf_count)
4933                         i = 0;
4934         }
4935
4936         info->tbuf_current = i;
4937
4938         /* set first buffer count to make new data visible to DMA controller */
4939         d = &info->tbufs[info->tbuf_start];
4940         set_desc_count(*d, d->buf_count);
4941
4942         /* start transmitter if needed and update transmit timeout */
4943         if (!info->tx_active)
4944                 tx_start(info);
4945         update_tx_timer(info);
4946
4947         return true;
4948 }
4949
4950 static int register_test(struct slgt_info *info)
4951 {
4952         static unsigned short patterns[] =
4953                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4954         static unsigned int count = ARRAY_SIZE(patterns);
4955         unsigned int i;
4956         int rc = 0;
4957
4958         for (i=0 ; i < count ; i++) {
4959                 wr_reg16(info, TIR, patterns[i]);
4960                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4961                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4962                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4963                         rc = -ENODEV;
4964                         break;
4965                 }
4966         }
4967         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4968         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4969         return rc;
4970 }
4971
4972 static int irq_test(struct slgt_info *info)
4973 {
4974         unsigned long timeout;
4975         unsigned long flags;
4976         struct tty_struct *oldtty = info->port.tty;
4977         u32 speed = info->params.data_rate;
4978
4979         info->params.data_rate = 921600;
4980         info->port.tty = NULL;
4981
4982         spin_lock_irqsave(&info->lock, flags);
4983         async_mode(info);
4984         slgt_irq_on(info, IRQ_TXIDLE);
4985
4986         /* enable transmitter */
4987         wr_reg16(info, TCR,
4988                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4989
4990         /* write one byte and wait for tx idle */
4991         wr_reg16(info, TDR, 0);
4992
4993         /* assume failure */
4994         info->init_error = DiagStatus_IrqFailure;
4995         info->irq_occurred = false;
4996
4997         spin_unlock_irqrestore(&info->lock, flags);
4998
4999         timeout=100;
5000         while(timeout-- && !info->irq_occurred)
5001                 msleep_interruptible(10);
5002
5003         spin_lock_irqsave(&info->lock,flags);
5004         reset_port(info);
5005         spin_unlock_irqrestore(&info->lock,flags);
5006
5007         info->params.data_rate = speed;
5008         info->port.tty = oldtty;
5009
5010         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
5011         return info->irq_occurred ? 0 : -ENODEV;
5012 }
5013
5014 static int loopback_test_rx(struct slgt_info *info)
5015 {
5016         unsigned char *src, *dest;
5017         int count;
5018
5019         if (desc_complete(info->rbufs[0])) {
5020                 count = desc_count(info->rbufs[0]);
5021                 src   = info->rbufs[0].buf;
5022                 dest  = info->tmp_rbuf;
5023
5024                 for( ; count ; count-=2, src+=2) {
5025                         /* src=data byte (src+1)=status byte */
5026                         if (!(*(src+1) & (BIT9 + BIT8))) {
5027                                 *dest = *src;
5028                                 dest++;
5029                                 info->tmp_rbuf_count++;
5030                         }
5031                 }
5032                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
5033                 return 1;
5034         }
5035         return 0;
5036 }
5037
5038 static int loopback_test(struct slgt_info *info)
5039 {
5040 #define TESTFRAMESIZE 20
5041
5042         unsigned long timeout;
5043         u16 count = TESTFRAMESIZE;
5044         unsigned char buf[TESTFRAMESIZE];
5045         int rc = -ENODEV;
5046         unsigned long flags;
5047
5048         struct tty_struct *oldtty = info->port.tty;
5049         MGSL_PARAMS params;
5050
5051         memcpy(&params, &info->params, sizeof(params));
5052
5053         info->params.mode = MGSL_MODE_ASYNC;
5054         info->params.data_rate = 921600;
5055         info->params.loopback = 1;
5056         info->port.tty = NULL;
5057
5058         /* build and send transmit frame */
5059         for (count = 0; count < TESTFRAMESIZE; ++count)
5060                 buf[count] = (unsigned char)count;
5061
5062         info->tmp_rbuf_count = 0;
5063         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
5064
5065         /* program hardware for HDLC and enabled receiver */
5066         spin_lock_irqsave(&info->lock,flags);
5067         async_mode(info);
5068         rx_start(info);
5069         tx_load(info, buf, count);
5070         spin_unlock_irqrestore(&info->lock, flags);
5071
5072         /* wait for receive complete */
5073         for (timeout = 100; timeout; --timeout) {
5074                 msleep_interruptible(10);
5075                 if (loopback_test_rx(info)) {
5076                         rc = 0;
5077                         break;
5078                 }
5079         }
5080
5081         /* verify received frame length and contents */
5082         if (!rc && (info->tmp_rbuf_count != count ||
5083                   memcmp(buf, info->tmp_rbuf, count))) {
5084                 rc = -ENODEV;
5085         }
5086
5087         spin_lock_irqsave(&info->lock,flags);
5088         reset_adapter(info);
5089         spin_unlock_irqrestore(&info->lock,flags);
5090
5091         memcpy(&info->params, &params, sizeof(info->params));
5092         info->port.tty = oldtty;
5093
5094         info->init_error = rc ? DiagStatus_DmaFailure : 0;
5095         return rc;
5096 }
5097
5098 static int adapter_test(struct slgt_info *info)
5099 {
5100         DBGINFO(("testing %s\n", info->device_name));
5101         if (register_test(info) < 0) {
5102                 printk("register test failure %s addr=%08X\n",
5103                         info->device_name, info->phys_reg_addr);
5104         } else if (irq_test(info) < 0) {
5105                 printk("IRQ test failure %s IRQ=%d\n",
5106                         info->device_name, info->irq_level);
5107         } else if (loopback_test(info) < 0) {
5108                 printk("loopback test failure %s\n", info->device_name);
5109         }
5110         return info->init_error;
5111 }
5112
5113 /*
5114  * transmit timeout handler
5115  */
5116 static void tx_timeout(unsigned long context)
5117 {
5118         struct slgt_info *info = (struct slgt_info*)context;
5119         unsigned long flags;
5120
5121         DBGINFO(("%s tx_timeout\n", info->device_name));
5122         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5123                 info->icount.txtimeout++;
5124         }
5125         spin_lock_irqsave(&info->lock,flags);
5126         tx_stop(info);
5127         spin_unlock_irqrestore(&info->lock,flags);
5128
5129 #if SYNCLINK_GENERIC_HDLC
5130         if (info->netcount)
5131                 hdlcdev_tx_done(info);
5132         else
5133 #endif
5134                 bh_transmit(info);
5135 }
5136
5137 /*
5138  * receive buffer polling timer
5139  */
5140 static void rx_timeout(unsigned long context)
5141 {
5142         struct slgt_info *info = (struct slgt_info*)context;
5143         unsigned long flags;
5144
5145         DBGINFO(("%s rx_timeout\n", info->device_name));
5146         spin_lock_irqsave(&info->lock, flags);
5147         info->pending_bh |= BH_RECEIVE;
5148         spin_unlock_irqrestore(&info->lock, flags);
5149         bh_handler(&info->task);
5150 }
5151