include/configs/tqma6.h

   1 /*
   2  * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
   3  *
   4  * Configuration settings for the TQ Systems TQMa6<Q,S> module.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12
  13 /* SPL */
  14 /* #if defined(CONFIG_SPL_BUILD) */
  15
  16 #define CONFIG_SPL_MMC_SUPPORT
  17 #define CONFIG_SPL_SPI_SUPPORT
  18 #define CONFIG_SPL_FAT_SUPPORT
  19 #define CONFIG_SPL_EXT_SUPPORT
  20
  21 /* common IMX6 SPL configuration */
  22 #include "imx6_spl.h"
  23
  24 /* #endif */
  25
  26 #include "mx6_common.h"
  27 #include <asm/arch/imx-regs.h>
  28 #include <asm/imx-common/gpio.h>
  29 #include <linux/sizes.h>
  30
  31 #define PHYS_SDRAM_SIZE                 (512u * SZ_1M)
  32 #define PHYS_SDRAM_SIZE                 (1024u * SZ_1M)
  33 #endif
  34
  35 #define CONFIG_DISPLAY_CPUINFO
  36 #define CONFIG_DISPLAY_BOARDINFO
  37 #define CONFIG_SYS_GENERIC_BOARD
  38
  39 #define CONFIG_CMDLINE_TAG
  40 #define CONFIG_SETUP_MEMORY_TAGS
  41 #define CONFIG_INITRD_TAG
  42 #define CONFIG_REVISION_TAG
  43
  44 #define CONFIG_BOARD_EARLY_INIT_F
  45 #define CONFIG_BOARD_LATE_INIT
  46
  47 #define CONFIG_MXC_GPIO
  48 #define CONFIG_MXC_UART
  49
  50 /* SPI */
  51 #define CONFIG_CMD_SPI
  52 #define CONFIG_MXC_SPI
  53
  54 /* SPI Flash */
  55 #define CONFIG_SPI_FLASH
  56 #define CONFIG_SPI_FLASH_STMICRO
  57
  58 #define TQMA6_SPI_FLASH_SECTOR_SIZE     SZ_64K
  59
  60 #define CONFIG_CMD_SF
  61 #define CONFIG_SF_DEFAULT_BUS   0
  62 #define CONFIG_SF_DEFAULT_CS    0
  63 #define CONFIG_SF_DEFAULT_SPEED 50000000
  64 #define CONFIG_SF_DEFAULT_MODE  (SPI_MODE_0)
  65
  66 /* I2C Configs */
  67 #define CONFIG_CMD_I2C
  68 #define CONFIG_SYS_I2C
  69 #define CONFIG_SYS_I2C_MXC
  70 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  71 #define CONFIG_I2C_MULTI_BUS
  72 #define CONFIG_SYS_I2C_SPEED            100000
  73
  74 /* I2C SYSMON (LM75) */
  75 #define CONFIG_DTT_LM75
  76 #define CONFIG_DTT_MAX_TEMP             70
  77 #define CONFIG_DTT_MIN_TEMP             -30
  78 #define CONFIG_DTT_HYSTERESIS   3
  79 #define CONFIG_CMD_DTT
  80
  81 /* I2C EEPROM (M24C64) */
  82 #define CONFIG_SYS_I2C_EEPROM_ADDR                      0x50
  83 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                  2
  84 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS           5 /* 32 Bytes */
  85 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS       20
  86 #define CONFIG_CMD_EEPROM
  87
  88 #define CONFIG_POWER
  89 #define CONFIG_POWER_I2C
  90 #define CONFIG_POWER_PFUZE100
  91 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  92 #define TQMA6_PFUZE100_I2C_BUS          2
  93
  94 /* MMC Configs */
  95 #define CONFIG_FSL_ESDHC
  96 #define CONFIG_FSL_USDHC
  97 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  98
  99 #define CONFIG_MMC
 100 #define CONFIG_CMD_MMC
 101 #define CONFIG_GENERIC_MMC
 102 #define CONFIG_BOUNCE_BUFFER
 103
 104 /* USB Configs */
 105 #define CONFIG_CMD_USB
 106 #define CONFIG_USB_EHCI
 107 #define CONFIG_USB_EHCI_MX6
 108 #define CONFIG_USB_STORAGE
 109 #define CONFIG_USB_HOST_ETHER
 110 #define CONFIG_USB_ETHER_SMSC95XX
 111 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 112 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 113 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 114
 115 /* Fuses */
 116 #define CONFIG_MXC_OCOTP
 117 #define CONFIG_CMD_FUSE
 118
 119 #define CONFIG_CMD_EXT2
 120 #define CONFIG_CMD_EXT4
 121 #define CONFIG_CMD_EXT4_WRITE
 122 #define CONFIG_CMD_FAT
 123 #define CONFIG_CMD_FS_GENERIC
 124 #define CONFIG_DOS_PARTITION
 125
 126 #define CONFIG_CMD_PING
 127 #define CONFIG_CMD_DHCP
 128 #define CONFIG_CMD_MII
 129 #define CONFIG_CMD_NET
 130
 131 #define CONFIG_FEC_MXC
 132 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 133 #define CONFIG_PHYLIB
 134 #define CONFIG_MII
 135
 136 #define CONFIG_ARP_TIMEOUT              200UL
 137 /* Network config - Allow larger/faster download for TFTP/NFS */
 138 #define CONFIG_IP_DEFRAG
 139 #define CONFIG_TFTP_BLOCKSIZE   4096
 140 #define CONFIG_NFS_READ_SIZE    4096
 141
 142 /* allow to overwrite serial and ethaddr */
 143 #define CONFIG_ENV_OVERWRITE
 144 #define CONFIG_CONS_INDEX               1
 145 #define CONFIG_BAUDRATE                 115200
 146
 147 /* Command definition */
 148 #include <config_cmd_default.h>
 149
 150 #define CONFIG_CMD_BMODE
 151 #define CONFIG_CMD_BOOTZ
 152 #define CONFIG_CMD_ITEST
 153 #define CONFIG_CMD_SETEXPR
 154 #undef CONFIG_CMD_IMLS
 155
 156 #define CONFIG_BOOTDELAY                3
 157
 158 #define CONFIG_LOADADDR                 0x12000000
 159
 160 /* place code in last 4 MiB of RAM */
 161 #define CONFIG_SYS_TEXT_BASE            0x2fc00000
 162 #define CONFIG_SYS_TEXT_BASE            0x4fc00000
 163 #endif
 164
 165 #define CONFIG_ENV_SIZE                 (SZ_8K)
 166 /* Size of malloc() pool */
 167 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2 * SZ_1M)
 168
 169 #if defined(CONFIG_TQMA6X_MMC_BOOT)
 170
 171 #define CONFIG_ENV_IS_IN_MMC
 172 #define TQMA6_UBOOT_OFFSET              SZ_1K
 173 #define TQMA6_UBOOT_SECTOR_START        0x2
 174 #define TQMA6_UBOOT_SECTOR_COUNT        0x7fe
 175
 176 #define CONFIG_ENV_OFFSET               SZ_1M
 177 #define CONFIG_SYS_MMC_ENV_DEV          0
 178
 179 #define TQMA6_FDT_OFFSET                (2 * SZ_1M)
 180 #define TQMA6_FDT_SECTOR_START          0x1000
 181 #define TQMA6_FDT_SECTOR_COUNT          0x800
 182
 183 #define TQMA6_KERNEL_SECTOR_START       0x2000
 184 #define TQMA6_KERNEL_SECTOR_COUNT       0x2000
 185
 186 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 187         "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
 188         "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
 189         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 190         "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
 191         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 192         "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
 193         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
 194         "loadimage=mmc dev ${mmcdev}; "                                        \
 195                 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
 196         "loadfdt=mmc dev ${mmcdev}; "                                          \
 197                 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
 198         "update_uboot=if tftp ${uboot}; then "                                 \
 199                 "if itest ${filesize} > 0; then "                              \
 200                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 201                         "setexpr blkc ${filesize} / 0x200; "                   \
 202                         "setexpr blkc ${blkc} + 1; "                           \
 203                         "if itest ${blkc} <= ${uboot_size}; then "             \
 204                                 "mmc write ${loadaddr} ${uboot_start} "        \
 205                                         "${blkc}; "                            \
 206                         "fi; "                                                 \
 207                 "fi; fi; "                                                     \
 208                 "setenv filesize; setenv blkc \0"                              \
 209         "update_kernel=run kernel_name; "                                      \
 210                 "if tftp ${kernel}; then "                                     \
 211                         "if itest ${filesize} > 0; then "                      \
 212                                 "mmc dev ${mmcdev}; mmc rescan; "              \
 213                                 "setexpr blkc ${filesize} / 0x200; "           \
 214                                 "setexpr blkc ${blkc} + 1; "                   \
 215                                 "if itest ${blkc} <= ${kernel_size}; then "    \
 216                                         "mmc write ${loadaddr} "               \
 217                                                 "${kernel_start} ${blkc}; "    \
 218                                 "fi; "                                         \
 219                         "fi; "                                                 \
 220                 "fi; "                                                         \
 221                 "setenv filesize; setenv blkc \0"                              \
 222         "update_fdt=if tftp ${fdt_file}; then "                                \
 223                 "if itest ${filesize} > 0; then "                              \
 224                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 225                         "setexpr blkc ${filesize} / 0x200; "                   \
 226                         "setexpr blkc ${blkc} + 1; "                           \
 227                         "if itest ${blkc} <= ${fdt_size}; then "               \
 228                                 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
 229                         "fi; "                                                 \
 230                 "fi; fi; "                                                     \
 231                 "setenv filesize; setenv blkc \0"                              \
 232
 233 #define CONFIG_BOOTCOMMAND \
 234         "run mmcboot; run netboot; run panicboot"
 235
 236 #elif defined(CONFIG_TQMA6X_SPI_BOOT)
 237
 238 #define TQMA6_UBOOT_OFFSET              0x400
 239 #define TQMA6_UBOOT_SECTOR_START        0x0
 240 /* max u-boot size: 512k */
 241 #define TQMA6_UBOOT_SECTOR_SIZE         TQMA6_SPI_FLASH_SECTOR_SIZE
 242 #define TQMA6_UBOOT_SECTOR_COUNT        0x8
 243 #define TQMA6_UBOOT_SIZE                (TQMA6_UBOOT_SECTOR_SIZE * \
 244                                          TQMA6_UBOOT_SECTOR_COUNT)
 245
 246 #define CONFIG_ENV_IS_IN_SPI_FLASH
 247 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 248 #define CONFIG_ENV_OFFSET               (TQMA6_UBOOT_SIZE)
 249 #define CONFIG_ENV_SECT_SIZE            TQMA6_SPI_FLASH_SECTOR_SIZE
 250 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 251                                          CONFIG_ENV_SECT_SIZE)
 252
 253 #define CONFIG_ENV_SPI_BUS              (CONFIG_SF_DEFAULT_BUS)
 254 #define CONFIG_ENV_SPI_CS               (CONFIG_SF_DEFAULT_CS)
 255 #define CONFIG_ENV_SPI_MAX_HZ           (CONFIG_SF_DEFAULT_SPEED)
 256 #define CONFIG_ENV_SPI_MODE             (CONFIG_SF_DEFAULT_MODE)
 257
 258 #define TQMA6_FDT_OFFSET                (CONFIG_ENV_OFFSET_REDUND + \
 259                                          CONFIG_ENV_SECT_SIZE)
 260 #define TQMA6_FDT_SECT_SIZE             (TQMA6_SPI_FLASH_SECTOR_SIZE)
 261
 262 #define TQMA6_FDT_SECTOR_START          0x0a /* 8 Sector u-boot, 2 Sector env */
 263 #define TQMA6_FDT_SECTOR_COUNT          0x01
 264
 265 #define TQMA6_KERNEL_SECTOR_START       0x10
 266 #define TQMA6_KERNEL_SECTOR_COUNT       0x60
 267
 268 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 269         "mmcblkdev=0\0"                                                        \
 270         "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
 271         "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
 272         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 273         "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
 274         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 275         "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
 276         "update_uboot=if tftp ${uboot}; then "                                 \
 277                 "if itest ${filesize} > 0; then "                              \
 278                         "setexpr blkc ${filesize} + "                          \
 279                                 __stringify(TQMA6_UBOOT_OFFSET) "; "           \
 280                         "setexpr size ${uboot_sectors} * "                     \
 281                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 282                         "if itest ${blkc} <= ${size}; then "                   \
 283                                 "sf probe; "                                   \
 284                                 "sf erase 0 ${size}; "                         \
 285                                 "sf write ${loadaddr} ${uboot_offset} "        \
 286                                         "${filesize}; "                        \
 287                         "fi; "                                                 \
 288                 "fi; fi; "                                                     \
 289                 "setenv filesize 0; setenv blkc; setenv size \0"               \
 290         "update_kernel=run kernel_name; if tftp ${kernel}; then "              \
 291                 "if itest ${filesize} > 0; then "                              \
 292                         "setexpr size ${kernel_sectors} * "                    \
 293                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 294                         "setexpr offset ${kernel_start} * "                    \
 295                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 296                         "if itest ${filesize} <= ${size}; then "               \
 297                                 "sf probe; "                                   \
 298                                 "sf erase ${offset} ${size}; "                 \
 299                                 "sf write ${loadaddr} ${offset} "              \
 300                                         "${filesize}; "                        \
 301                         "fi; "                                                 \
 302                 "fi; fi; "                                                     \
 303                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 304         "update_fdt=if tftp ${fdt_file}; then "                                \
 305                 "if itest ${filesize} > 0; then "                              \
 306                         "setexpr size ${fdt_sectors} * "                       \
 307                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 308                         "setexpr offset ${fdt_start} * "                       \
 309                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 310                         "if itest ${filesize} <= ${size}; then "               \
 311                                 "sf probe; "                                   \
 312                                 "sf erase ${offset} ${size}; "                 \
 313                                 "sf write ${loadaddr} ${offset} "              \
 314                                         "${filesize}; "                        \
 315                         "fi; "                                                 \
 316                 "fi; fi; "                                                     \
 317                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 318         "loadimage=sf probe; "                                                 \
 319                 "setexpr size ${kernel_sectors} * "                            \
 320                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 321                 "setexpr offset ${kernel_start} * "                            \
 322                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 323                 "sf read ${loadaddr} ${offset} ${size}; "                      \
 324                 "setenv size ; setenv offset\0"                                \
 325         "loadfdt=sf probe; "                                                   \
 326                 "setexpr size ${fdt_sectors} * "                               \
 327                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 328                 "setexpr offset ${fdt_start} * "                               \
 329                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 330                 "sf read ${${fdt_addr}} ${offset} ${size}; "                   \
 331                 "setenv size ; setenv offset\0"                                \
 332
 333
 334 #define CONFIG_BOOTCOMMAND                                                     \
 335         "sf probe; run mmcboot; run netboot; run panicboot"                    \
 336
 337 #else
 338
 339 #error "need to define boot source"
 340
 341 #endif
 342
 343 /* 128 MiB offset as in ARM related docu for linux suggested */
 344 #define TQMA6_FDT_ADDRESS               0x18000000
 345
 346 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
 347         "board=tqma6\0"                                                        \
 348         "uimage=uImage\0"                                                      \
 349         "zimage=zImage\0"                                                      \
 350         "boot_type=bootz\0"                                                    \
 351         "kernel_name=if test \"${boot_type}\" != bootz; then "                 \
 352                 "setenv kernel ${uimage}; "                                    \
 353                 "else setenv kernel ${zimage}; fi\0"                           \
 354         "uboot=u-boot.imx\0"                                                   \
 355         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
 356         "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
 357         "console=" CONFIG_CONSOLE_DEV "\0"                                     \
 358         "fdt_high=0xffffffff\0"                                                \
 359         "initrd_high=0xffffffff\0"                                             \
 360         "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
 361         "addfb=setenv bootargs ${bootargs} "                                   \
 362                 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
 363         "mmcpart=2\0"                                                          \
 364         "mmcblkdev=0\0"                                                        \
 365         "mmcargs=run addmmc addtty addfb\0"                                    \
 366         "addmmc=setenv bootargs ${bootargs} "                                  \
 367                 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0"        \
 368         "mmcboot=echo Booting from mmc ...; "                                  \
 369                 "setenv bootargs; "                                            \
 370                 "run mmcargs; "                                                \
 371                 "run loadimage; "                                              \
 372                 "if run loadfdt; then "                                        \
 373                         "echo boot device tree kernel ...; "                   \
 374                         "${boot_type} ${loadaddr} - ${fdt_addr}; "             \
 375                 "else "                                                        \
 376                         "${boot_type}; "                                       \
 377                 "fi;\0"                                                        \
 378                 "setenv bootargs \0"                                           \
 379         "netdev=eth0\0"                                                        \
 380         "rootpath=/srv/nfs/tqma6\0"                                            \
 381         "ipmode=static\0"                                                      \
 382         "netargs=run addnfs addip addtty addfb\0"                              \
 383         "addnfs=setenv bootargs ${bootargs} "                                  \
 384                 "root=/dev/nfs rw "                                            \
 385                 "nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
 386         "addip_static=setenv bootargs ${bootargs} "                            \
 387                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
 388                 "${hostname}:${netdev}:off\0"                                  \
 389         "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
 390         "addip=if test \"${ipmode}\" != static; then "                         \
 391                 "run addip_dynamic; else run addip_static; fi\0"               \
 392         "set_getcmd=if test \"${ipmode}\" != static; then "                    \
 393                 "setenv getcmd dhcp; setenv autoload yes; "                    \
 394                 "else setenv getcmd tftp; setenv autoload no; fi\0"            \
 395         "netboot=echo Booting from net ...; "                                  \
 396                 "run kernel_name; "                                            \
 397                 "run set_getcmd; "                                             \
 398                 "setenv bootargs; "                                            \
 399                 "run netargs; "                                                \
 400                 "if ${getcmd} ${kernel}; then "                                \
 401                         "if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
 402                                 "${boot_type} ${loadaddr} - ${fdt_addr}; "     \
 403                         "fi; "                                                 \
 404                 "fi; "                                                         \
 405                 "echo ... failed\0"                                            \
 406         "panicboot=echo No boot device !!! reset\0"                            \
 407         TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \
 408
 409 /* Miscellaneous configurable options */
 410 #define CONFIG_SYS_LONGHELP
 411 #define CONFIG_SYS_HUSH_PARSER
 412 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 413
 414 #define CONFIG_AUTO_COMPLETE
 415 #define CONFIG_SYS_CBSIZE               512
 416
 417 /* Print Buffer Size */
 418 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 419                                          sizeof(CONFIG_SYS_PROMPT) + 16)
 420 #define CONFIG_SYS_MAXARGS              16
 421 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 422
 423 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 424
 425 #define CONFIG_CMDLINE_EDITING
 426 #define CONFIG_STACKSIZE                (128u * SZ_1K)
 427
 428 /* Physical Memory Map */
 429 #define CONFIG_NR_DRAM_BANKS            1
 430 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 431
 432 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 433 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 434 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 435
 436 #define CONFIG_SYS_INIT_SP_OFFSET \
 437         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 438 #define CONFIG_SYS_INIT_SP_ADDR \
 439         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 440
 441 /* FLASH and environment organization */
 442 #define CONFIG_SYS_NO_FLASH
 443
 444 #define CONFIG_OF_LIBFDT
 445 #define CONFIG_OF_BOARD_SETUP
 446 #define CONFIG_FIT
 447 #define CONFIG_FIT_VERBOSE
 448
 449 #ifndef CONFIG_SYS_DCACHE_OFF
 450 #define CONFIG_CMD_CACHE
 451 #endif
 452
 453 /*
 454  * All the defines above are for the TQMa6 SoM
 455  *
 456  * Now include the baseboard specific configuration
 457  */
 458 #ifdef CONFIG_MBA6
 459 #include "tqma6_mba6.h"
 460 #else
 461 #error "No baseboard for the TQMa6 defined!"
 462 #endif
 463
 464 /* Support at least the sensor on TQMa6 SOM */
 465 #if !defined(CONFIG_DTT_SENSORS)
 466 #define CONFIG_DTT_SENSORS              { 0 }
 467 #endif
 468
 469 #endif /* __CONFIG_H */