DECLARE_GLOBAL_DATA_PTR;
-#undef DEBUG
-/* #define DEBUG */
-#ifdef CONFIG_PCI
-#define MAP_PCI
-#endif /* of CONFIG_PCI */
-
-#ifdef DEBUG
-#define DP(x) x
-#else
-#define DP(x)
-#endif
-
int set_dfcdlInit(void); /* setup delay line of Mv64360 */
/* ------------------------------------------------------------------------- */
return 0;
}
-#define GB (1 << 30)
+#define GB (1 << 30)
/* much of this code is based on (or is) the code in the pip405 port */
/* thanks go to the authors of said port - Josh */
/* SDRAM/DDR information struct */
-typedef struct _gtMemoryDimmInfo
-{
- MEMORY_TYPE memoryType;
- unsigned int numOfRowAddresses;
- unsigned int numOfColAddresses;
- unsigned int numOfModuleBanks;
- unsigned int dataWidth;
- VOLTAGE_INTERFACE voltageInterface;
- unsigned int errorCheckType; /* ECC , PARITY..*/
- unsigned int sdramWidth; /* 4,8,16 or 32 */;
- unsigned int errorCheckDataWidth; /* 0 - no, 1 - Yes */
- unsigned int minClkDelay;
- unsigned int burstLengthSupported;
- unsigned int numOfBanksOnEachDevice;
- unsigned int suportedCasLatencies;
- unsigned int RefreshInterval;
- unsigned int maxCASlatencySupported_LoP; /* LoP left of point (measured in ns) */
- unsigned int maxCASlatencySupported_RoP; /* RoP right of point (measured in ns)*/
- MAX_CL_SUPPORTED_DDR maxClSupported_DDR;
- MAX_CL_SUPPORTED_SD maxClSupported_SD;
- unsigned int moduleBankDensity;
- /* module attributes (true for yes) */
- bool bufferedAddrAndControlInputs;
- bool registeredAddrAndControlInputs;
- bool onCardPLL;
- bool bufferedDQMBinputs;
- bool registeredDQMBinputs;
- bool differentialClockInput;
- bool redundantRowAddressing;
-
- /* module general attributes */
- bool suportedAutoPreCharge;
- bool suportedPreChargeAll;
- bool suportedEarlyRasPreCharge;
- bool suportedWrite1ReadBurst;
- bool suported5PercentLowVCC;
- bool suported5PercentUpperVCC;
- /* module timing parameters */
- unsigned int minRasToCasDelay;
- unsigned int minRowActiveRowActiveDelay;
- unsigned int minRasPulseWidth;
- unsigned int minRowPrechargeTime; /* measured in ns */
-
- int addrAndCommandHoldTime; /* LoP left of point (measured in ns) */
- int addrAndCommandSetupTime; /* (measured in ns/100) */
- int dataInputSetupTime; /* LoP left of point (measured in ns) */
- int dataInputHoldTime; /* LoP left of point (measured in ns) */
+typedef struct _gtMemoryDimmInfo {
+ MEMORY_TYPE memoryType;
+ unsigned int numOfRowAddresses;
+ unsigned int numOfColAddresses;
+ unsigned int numOfModuleBanks;
+ unsigned int dataWidth;
+ VOLTAGE_INTERFACE voltageInterface;
+ unsigned int errorCheckType; /* ECC , PARITY.. */
+ unsigned int sdramWidth; /* 4,8,16 or 32 */ ;
+ unsigned int errorCheckDataWidth; /* 0 - no, 1 - Yes */
+ unsigned int minClkDelay;
+ unsigned int burstLengthSupported;
+ unsigned int numOfBanksOnEachDevice;
+ unsigned int suportedCasLatencies;
+ unsigned int RefreshInterval;
+ unsigned int maxCASlatencySupported_LoP; /* LoP left of point (measured in ns) */
+ unsigned int maxCASlatencySupported_RoP; /* RoP right of point (measured in ns) */
+ MAX_CL_SUPPORTED_DDR maxClSupported_DDR;
+ MAX_CL_SUPPORTED_SD maxClSupported_SD;
+ unsigned int moduleBankDensity;
+ /* module attributes (true for yes) */
+ bool bufferedAddrAndControlInputs;
+ bool registeredAddrAndControlInputs;
+ bool onCardPLL;
+ bool bufferedDQMBinputs;
+ bool registeredDQMBinputs;
+ bool differentialClockInput;
+ bool redundantRowAddressing;
+
+ /* module general attributes */
+ bool suportedAutoPreCharge;
+ bool suportedPreChargeAll;
+ bool suportedEarlyRasPreCharge;
+ bool suportedWrite1ReadBurst;
+ bool suported5PercentLowVCC;
+ bool suported5PercentUpperVCC;
+ /* module timing parameters */
+ unsigned int minRasToCasDelay;
+ unsigned int minRowActiveRowActiveDelay;
+ unsigned int minRasPulseWidth;
+ unsigned int minRowPrechargeTime; /* measured in ns */
+
+ int addrAndCommandHoldTime; /* LoP left of point (measured in ns) */
+ int addrAndCommandSetupTime; /* (measured in ns/100) */
+ int dataInputSetupTime; /* LoP left of point (measured in ns) */
+ int dataInputHoldTime; /* LoP left of point (measured in ns) */
/* tAC times for highest 2nd and 3rd highest CAS Latency values */
- unsigned int clockToDataOut_LoP; /* LoP left of point (measured in ns) */
- unsigned int clockToDataOut_RoP; /* RoP right of point (measured in ns)*/
- unsigned int clockToDataOutMinus1_LoP; /* LoP left of point (measured in ns) */
- unsigned int clockToDataOutMinus1_RoP; /* RoP right of point (measured in ns)*/
- unsigned int clockToDataOutMinus2_LoP; /* LoP left of point (measured in ns) */
- unsigned int clockToDataOutMinus2_RoP; /* RoP right of point (measured in ns)*/
-
- unsigned int minimumCycleTimeAtMaxCasLatancy_LoP; /* LoP left of point (measured in ns) */
- unsigned int minimumCycleTimeAtMaxCasLatancy_RoP; /* RoP right of point (measured in ns)*/
-
- unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_LoP; /* LoP left of point (measured in ns) */
- unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_RoP; /* RoP right of point (measured in ns)*/
-
- unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_LoP; /* LoP left of point (measured in ns) */
- unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_RoP; /* RoP right of point (measured in ns)*/
-
- /* Parameters calculated from
- the extracted DIMM information */
- unsigned int size;
- unsigned int deviceDensity; /* 16,64,128,256 or 512 Mbit */
- unsigned int numberOfDevices;
- uchar drb_size; /* DRAM size in n*64Mbit */
- uchar slot; /* Slot Number this module is inserted in */
- uchar spd_raw_data[128]; /* Content of SPD-EEPROM copied 1:1 */
+ unsigned int clockToDataOut_LoP; /* LoP left of point (measured in ns) */
+ unsigned int clockToDataOut_RoP; /* RoP right of point (measured in ns) */
+ unsigned int clockToDataOutMinus1_LoP; /* LoP left of point (measured in ns) */
+ unsigned int clockToDataOutMinus1_RoP; /* RoP right of point (measured in ns) */
+ unsigned int clockToDataOutMinus2_LoP; /* LoP left of point (measured in ns) */
+ unsigned int clockToDataOutMinus2_RoP; /* RoP right of point (measured in ns) */
+
+ unsigned int minimumCycleTimeAtMaxCasLatancy_LoP; /* LoP left of point (measured in ns) */
+ unsigned int minimumCycleTimeAtMaxCasLatancy_RoP; /* RoP right of point (measured in ns) */
+
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_LoP; /* LoP left of point (measured in ns) */
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_RoP; /* RoP right of point (measured in ns) */
+
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_LoP; /* LoP left of point (measured in ns) */
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_RoP; /* RoP right of point (measured in ns) */
+
+ /* Parameters calculated from
+ the extracted DIMM information */
+ unsigned int size;
+ unsigned int deviceDensity; /* 16,64,128,256 or 512 Mbit */
+ unsigned int numberOfDevices;
+ uchar drb_size; /* DRAM size in n*64Mbit */
+ uchar slot; /* Slot Number this module is inserted in */
+ uchar spd_raw_data[128]; /* Content of SPD-EEPROM copied 1:1 */
#ifdef DEBUG
- uchar manufactura[8]; /* Content of SPD-EEPROM Byte 64-71 */
- uchar modul_id[18]; /* Content of SPD-EEPROM Byte 73-90 */
- uchar vendor_data[27]; /* Content of SPD-EEPROM Byte 99-125 */
- unsigned long modul_serial_no; /* Content of SPD-EEPROM Byte 95-98 */
- unsigned int manufac_date; /* Content of SPD-EEPROM Byte 93-94 */
- unsigned int modul_revision; /* Content of SPD-EEPROM Byte 91-92 */
- uchar manufac_place; /* Content of SPD-EEPROM Byte 72 */
+ uchar manufactura[8]; /* Content of SPD-EEPROM Byte 64-71 */
+ uchar modul_id[18]; /* Content of SPD-EEPROM Byte 73-90 */
+ uchar vendor_data[27]; /* Content of SPD-EEPROM Byte 99-125 */
+ unsigned long modul_serial_no; /* Content of SPD-EEPROM Byte 95-98 */
+ unsigned int manufac_date; /* Content of SPD-EEPROM Byte 93-94 */
+ unsigned int modul_revision; /* Content of SPD-EEPROM Byte 91-92 */
+ uchar manufac_place; /* Content of SPD-EEPROM Byte 72 */
#endif
} AUX_MEM_DIMM_INFO;
/* static int check_dimm(uchar slot, AUX_MEM_DIMM_INFO *info) */
static int check_dimm (uchar slot, AUX_MEM_DIMM_INFO * dimmInfo)
{
- unsigned long spd_checksum;
-
uchar addr = slot == 0 ? DIMM0_I2C_ADDR : DIMM1_I2C_ADDR;
int ret;
unsigned int i, j, density = 1, devicesForErrCheck = 0;
uchar supp_cal, cal_val;
ulong memclk, tmemclk;
ulong tmp;
- uchar trp_clocks = 0, trcd_clocks, tras_clocks, trrd_clocks;
+ uchar trp_clocks = 0, tras_clocks;
uchar data[128];
memclk = gd->bus_clk;
ret = 0;
- DP (puts ("before i2c read\n"));
+ debug("before i2c read\n");
ret = i2c_read (addr, 0, 2, data, 128);
- DP (puts ("after i2c read\n"));
+ debug("after i2c read\n");
if ((data[64] != 'e') || (data[65] != 's') || (data[66] != 'd')
|| (data[67] != '-') || (data[68] != 'g') || (data[69] != 'm')
}
if (ret) {
- DP (printf ("No DIMM in slot %d [err = %x]\n", slot, ret));
+ debug("No DIMM in slot %d [err = %x]\n", slot, ret);
return 0;
} else
dimmInfo->slot = slot; /* start to fill up dimminfo for this "slot" */
-#ifdef CFG_DISPLAY_DIMM_SPD_CONTENT
+#ifdef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT
for (i = 0; i <= 127; i++) {
printf ("SPD-EEPROM Byte %3d = %3x (%3d)\n", i, data[i],
for (i = 0; i < sizeof (dimmInfo->manufactura); i++) {
dimmInfo->manufactura[i] = data[64 + i];
}
- printf ("\nThis RAM-Module is produced by: %s\n",
+ printf ("\nThis RAM-Module is produced by: %s\n",
dimmInfo->manufactura);
/* find Manul-ID of Dimm Module */
for (i = 0; i < sizeof (dimmInfo->modul_id); i++) {
dimmInfo->modul_id[i] = data[73 + i];
}
- printf ("The Module-ID of this RAM-Module is: %s\n",
+ printf ("The Module-ID of this RAM-Module is: %s\n",
dimmInfo->modul_id);
/* find Vendor-Data of Dimm Module */
for (i = 0; i < sizeof (dimmInfo->vendor_data); i++) {
dimmInfo->vendor_data[i] = data[99 + i];
}
- printf ("Vendor Data of this RAM-Module is: %s\n",
+ printf ("Vendor Data of this RAM-Module is: %s\n",
dimmInfo->vendor_data);
/* find modul_serial_no of Dimm Module */
dimmInfo->modul_serial_no = (*((unsigned long *) (&data[95])));
- printf ("Serial No. of this RAM-Module is: %ld (%lx)\n",
+ printf ("Serial No. of this RAM-Module is: %ld (%lx)\n",
dimmInfo->modul_serial_no, dimmInfo->modul_serial_no);
/* find Manufac-Data of Dimm Module */
dimmInfo->manufac_date = (*((unsigned int *) (&data[93])));
- printf ("Manufactoring Date of this RAM-Module is: %d.%d\n", data[93], data[94]); /*dimmInfo->manufac_date */
+ printf ("Manufactoring Date of this RAM-Module is: %d.%d\n", data[93], data[94]); /*dimmInfo->manufac_date */
/* find modul_revision of Dimm Module */
dimmInfo->modul_revision = (*((unsigned int *) (&data[91])));
/* find manufac_place of Dimm Module */
dimmInfo->manufac_place = (*((unsigned char *) (&data[72])));
- printf ("manufac_place of this RAM-Module is: %d\n",
+ printf ("manufac_place of this RAM-Module is: %d\n",
dimmInfo->manufac_place);
#endif
/*------------------------------------------------------------------------------------------------------------------------------*/
/* calculate SPD checksum */
/*------------------------------------------------------------------------------------------------------------------------------*/
- spd_checksum = 0;
#if 0 /* test-only */
+ spd_checksum = 0;
+
for (i = 0; i <= 62; i++) {
spd_checksum += data[i];
}
dimmInfo->memoryType = (data[i] == 0x7) ? DDR : SDRAM;
#ifdef DEBUG
if (dimmInfo->memoryType == 0)
- DP (printf
- ("Dram_type in slot %d is: SDRAM\n",
- dimmInfo->slot));
+ debug("Dram_type in slot %d is: SDRAM\n",
+ dimmInfo->slot);
if (dimmInfo->memoryType == 1)
- DP (printf
- ("Dram_type in slot %d is: DDRAM\n",
- dimmInfo->slot));
+ debug("Dram_type in slot %d is: DDRAM\n",
+ dimmInfo->slot);
#endif
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 3: /* Number Of Row Addresses */
dimmInfo->numOfRowAddresses = data[i];
- DP (printf
- ("Module Number of row addresses: %d\n",
- dimmInfo->numOfRowAddresses));
+ debug("Module Number of row addresses: %d\n",
+ dimmInfo->numOfRowAddresses);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 4: /* Number Of Column Addresses */
dimmInfo->numOfColAddresses = data[i];
- DP (printf
- ("Module Number of col addresses: %d\n",
- dimmInfo->numOfColAddresses));
+ debug("Module Number of col addresses: %d\n",
+ dimmInfo->numOfColAddresses);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 5: /* Number Of Module Banks */
dimmInfo->numOfModuleBanks = data[i];
- DP (printf
- ("Number of Banks on Mod. : %d\n",
- dimmInfo->numOfModuleBanks));
+ debug("Number of Banks on Mod. : %d\n",
+ dimmInfo->numOfModuleBanks);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 6: /* Data Width */
dimmInfo->dataWidth = data[i];
- DP (printf
- ("Module Data Width: %d\n",
- dimmInfo->dataWidth));
+ debug("Module Data Width: %d\n",
+ dimmInfo->dataWidth);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
switch (data[i]) {
case 0x0:
dimmInfo->voltageInterface = TTL_5V_TOLERANT;
- DP (printf
- ("Module is TTL_5V_TOLERANT\n"));
+ debug("Module is TTL_5V_TOLERANT\n");
break;
case 0x1:
dimmInfo->voltageInterface = LVTTL;
- DP (printf
- ("Module is LVTTL\n"));
+ debug("Module is LVTTL\n");
break;
case 0x2:
dimmInfo->voltageInterface = HSTL_1_5V;
- DP (printf
- ("Module is TTL_5V_TOLERANT\n"));
+ debug("Module is TTL_5V_TOLERANT\n");
break;
case 0x3:
dimmInfo->voltageInterface = SSTL_3_3V;
- DP (printf
- ("Module is HSTL_1_5V\n"));
+ debug("Module is HSTL_1_5V\n");
break;
case 0x4:
dimmInfo->voltageInterface = SSTL_2_5V;
- DP (printf
- ("Module is SSTL_2_5V\n"));
+ debug("Module is SSTL_2_5V\n");
break;
default:
dimmInfo->voltageInterface = VOLTAGE_UNKNOWN;
- DP (printf
- ("Module is VOLTAGE_UNKNOWN\n"));
+ debug("Module is VOLTAGE_UNKNOWN\n");
break;
}
break;
leftOfPoint;
dimmInfo->minimumCycleTimeAtMaxCasLatancy_RoP =
rightOfPoint;
- DP (printf
- ("Minimum Cycle Time At Max CasLatancy: %d.%d [ns]\n",
- leftOfPoint, rightOfPoint));
+ debug("Minimum Cycle Time At Max CasLatancy: %d.%d [ns]\n",
+ leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
rightOfPoint = time_tmp % div;
dimmInfo->clockToDataOut_LoP = leftOfPoint;
dimmInfo->clockToDataOut_RoP = rightOfPoint;
- DP (printf
- ("Clock To Data Out: %d.%2d [ns]\n",
- leftOfPoint, rightOfPoint));
+ debug("Clock To Data Out: %d.%2d [ns]\n",
+ leftOfPoint, rightOfPoint);
/*dimmInfo->clockToDataOut */
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
-#ifdef CONFIG_ECC
+#ifdef CONFIG_MV64360_ECC
case 11: /* Error Check Type */
dimmInfo->errorCheckType = data[i];
- DP (printf
- ("Error Check Type (0=NONE): %d\n",
- dimmInfo->errorCheckType));
+ debug("Error Check Type (0=NONE): %d\n",
+ dimmInfo->errorCheckType);
break;
-#endif
+#endif /* of ifdef CONFIG_MV64360_ECC */
/*------------------------------------------------------------------------------------------------------------------------------*/
case 12: /* Refresh Interval */
dimmInfo->RefreshInterval = data[i];
- DP (printf
- ("RefreshInterval (80= Self refresh Normal, 15.625us) : %x\n",
- dimmInfo->RefreshInterval));
+ debug("RefreshInterval (80= Self refresh Normal, 15.625us) : %x\n",
+ dimmInfo->RefreshInterval);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 13: /* Sdram Width */
dimmInfo->sdramWidth = data[i];
- DP (printf
- ("Sdram Width: %d\n",
- dimmInfo->sdramWidth));
+ debug("Sdram Width: %d\n",
+ dimmInfo->sdramWidth);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 14: /* Error Check Data Width */
dimmInfo->errorCheckDataWidth = data[i];
- DP (printf
- ("Error Check Data Width: %d\n",
- dimmInfo->errorCheckDataWidth));
+ debug("Error Check Data Width: %d\n",
+ dimmInfo->errorCheckDataWidth);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 15: /* Minimum Clock Delay */
dimmInfo->minClkDelay = data[i];
- DP (printf
- ("Minimum Clock Delay: %d\n",
- dimmInfo->minClkDelay));
+ debug("Minimum Clock Delay: %d\n",
+ dimmInfo->minClkDelay);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
/******-******-******-*******
* bit3 | bit2 | bit1 | bit0 *
*******-******-******-*******
- burst length = * 8 | 4 | 2 | 1 *
+ burst length = * 8 | 4 | 2 | 1 *
*****************************
If for example bit0 and bit2 are set, the burst
dimmInfo->burstLengthSupported = data[i];
#ifdef DEBUG
- DP (printf
- ("Burst Length Supported: "));
+ debug("Burst Length Supported: ");
if (dimmInfo->burstLengthSupported & 0x01)
- DP (printf ("1, "));
+ debug("1, ");
if (dimmInfo->burstLengthSupported & 0x02)
- DP (printf ("2, "));
+ debug("2, ");
if (dimmInfo->burstLengthSupported & 0x04)
- DP (printf ("4, "));
+ debug("4, ");
if (dimmInfo->burstLengthSupported & 0x08)
- DP (printf ("8, "));
- DP (printf (" Bit \n"));
+ debug("8, ");
+ debug(" Bit \n");
#endif
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 17: /* Number Of Banks On Each Device */
dimmInfo->numOfBanksOnEachDevice = data[i];
- DP (printf
- ("Number Of Banks On Each Chip: %d\n",
- dimmInfo->numOfBanksOnEachDevice));
+ debug("Number Of Banks On Each Chip: %d\n",
+ dimmInfo->numOfBanksOnEachDevice);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
*******-******-******-******-******-******-******-*******
* bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 *
*******-******-******-******-******-******-******-*******
- CAS = * TBD | TBD | 3.5 | 3 | 2.5 | 2 | 1.5 | 1 *
+ CAS = * TBD | TBD | 3.5 | 3 | 2.5 | 2 | 1.5 | 1 *
*********************************************************
SDRAM:
*******-******-******-******-******-******-******-*******
* bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 *
*******-******-******-******-******-******-******-*******
- CAS = * TBD | 7 | 6 | 5 | 4 | 3 | 2 | 1 *
+ CAS = * TBD | 7 | 6 | 5 | 4 | 3 | 2 | 1 *
********************************************************/
dimmInfo->suportedCasLatencies = data[i];
#ifdef DEBUG
- DP (printf
- ("Suported Cas Latencies: (CL) "));
+ debug("Suported Cas Latencies: (CL) ");
if (dimmInfo->memoryType == 0) { /* SDRAM */
for (k = 0; k <= 7; k++) {
if (dimmInfo->
suportedCasLatencies & (1 << k))
- DP (printf
- ("%d, ",
- k + 1));
+ debug("%d, ",
+ k + 1);
}
} else { /* DDR-RAM */
if (dimmInfo->suportedCasLatencies & 1)
- DP (printf ("1, "));
+ debug("1, ");
if (dimmInfo->suportedCasLatencies & 2)
- DP (printf ("1.5, "));
+ debug("1.5, ");
if (dimmInfo->suportedCasLatencies & 4)
- DP (printf ("2, "));
+ debug("2, ");
if (dimmInfo->suportedCasLatencies & 8)
- DP (printf ("2.5, "));
+ debug("2.5, ");
if (dimmInfo->suportedCasLatencies & 16)
- DP (printf ("3, "));
+ debug("3, ");
if (dimmInfo->suportedCasLatencies & 32)
- DP (printf ("3.5, "));
+ debug("3.5, ");
}
- DP (printf ("\n"));
+ debug("\n");
#endif
/* Calculating MAX CAS latency */
for (j = 7; j > 0; j--) {
/* CAS latency 1, 1.5, 2, 2.5, 3, 3.5 */
switch (j) {
case 7:
- DP (printf
- ("Max. Cas Latencies (DDR): ERROR !!!\n"));
+ debug("Max. Cas Latencies (DDR): ERROR !!!\n");
dimmInfo->
maxClSupported_DDR
=
hang ();
break;
case 6:
- DP (printf
- ("Max. Cas Latencies (DDR): ERROR !!!\n"));
+ debug("Max. Cas Latencies (DDR): ERROR !!!\n");
dimmInfo->
maxClSupported_DDR
=
hang ();
break;
case 5:
- DP (printf
- ("Max. Cas Latencies (DDR): 3.5 clk's\n"));
+ debug("Max. Cas Latencies (DDR): 3.5 clk's\n");
dimmInfo->
maxClSupported_DDR
= DDR_CL_3_5;
break;
case 4:
- DP (printf
- ("Max. Cas Latencies (DDR): 3 clk's \n"));
+ debug("Max. Cas Latencies (DDR): 3 clk's \n");
dimmInfo->
maxClSupported_DDR
= DDR_CL_3;
break;
case 3:
- DP (printf
- ("Max. Cas Latencies (DDR): 2.5 clk's \n"));
+ debug("Max. Cas Latencies (DDR): 2.5 clk's \n");
dimmInfo->
maxClSupported_DDR
= DDR_CL_2_5;
break;
case 2:
- DP (printf
- ("Max. Cas Latencies (DDR): 2 clk's \n"));
+ debug("Max. Cas Latencies (DDR): 2 clk's \n");
dimmInfo->
maxClSupported_DDR
= DDR_CL_2;
break;
case 1:
- DP (printf
- ("Max. Cas Latencies (DDR): 1.5 clk's \n"));
+ debug("Max. Cas Latencies (DDR): 1.5 clk's \n");
dimmInfo->
maxClSupported_DDR
= DDR_CL_1_5;
dimmInfo->
maxCASlatencySupported_RoP
= 0;
- DP (printf
- ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
+ debug("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
dimmInfo->
maxCASlatencySupported_LoP,
dimmInfo->
- maxCASlatencySupported_RoP));
+ maxCASlatencySupported_RoP);
break;
case SDRAM:
/* CAS latency 1, 2, 3, 4, 5, 6, 7 */
- dimmInfo->maxClSupported_SD = j; /* Cas Latency DDR-RAM Coded */
- DP (printf
- ("Max. Cas Latencies (SD): %d\n",
+ dimmInfo->maxClSupported_SD = j; /* Cas Latency DDR-RAM Coded */
+ debug("Max. Cas Latencies (SD): %d\n",
dimmInfo->
- maxClSupported_SD));
+ maxClSupported_SD);
dimmInfo->
maxCASlatencySupported_LoP
= j;
dimmInfo->
maxCASlatencySupported_RoP
= 0;
- DP (printf
- ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
+ debug("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
dimmInfo->
maxCASlatencySupported_LoP,
dimmInfo->
- maxCASlatencySupported_RoP));
+ maxCASlatencySupported_RoP);
break;
}
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 21: /* Buffered Address And Control Inputs */
- DP (printf ("\nModul Attributes (SPD Byte 21): \n"));
+ debug("\nModul Attributes (SPD Byte 21): \n");
dimmInfo->bufferedAddrAndControlInputs =
data[i] & BIT0;
dimmInfo->registeredAddrAndControlInputs =
(data[i] & BIT5) >> 5;
dimmInfo->redundantRowAddressing =
(data[i] & BIT6) >> 6;
-#ifdef DEBUG
+
if (dimmInfo->bufferedAddrAndControlInputs == 1)
- DP (printf
- (" - Buffered Address/Control Input: Yes \n"));
+ debug(" - Buffered Address/Control Input: Yes \n");
else
- DP (printf
- (" - Buffered Address/Control Input: No \n"));
+ debug(" - Buffered Address/Control Input: No \n");
if (dimmInfo->registeredAddrAndControlInputs == 1)
- DP (printf
- (" - Registered Address/Control Input: Yes \n"));
+ debug(" - Registered Address/Control Input: Yes \n");
else
- DP (printf
- (" - Registered Address/Control Input: No \n"));
+ debug(" - Registered Address/Control Input: No \n");
if (dimmInfo->onCardPLL == 1)
- DP (printf
- (" - On-Card PLL (clock): Yes \n"));
+ debug(" - On-Card PLL (clock): Yes \n");
else
- DP (printf
- (" - On-Card PLL (clock): No \n"));
+ debug(" - On-Card PLL (clock): No \n");
if (dimmInfo->bufferedDQMBinputs == 1)
- DP (printf
- (" - Bufferd DQMB Inputs: Yes \n"));
+ debug(" - Bufferd DQMB Inputs: Yes \n");
else
- DP (printf
- (" - Bufferd DQMB Inputs: No \n"));
+ debug(" - Bufferd DQMB Inputs: No \n");
if (dimmInfo->registeredDQMBinputs == 1)
- DP (printf
- (" - Registered DQMB Inputs: Yes \n"));
+ debug(" - Registered DQMB Inputs: Yes \n");
else
- DP (printf
- (" - Registered DQMB Inputs: No \n"));
+ debug(" - Registered DQMB Inputs: No \n");
if (dimmInfo->differentialClockInput == 1)
- DP (printf
- (" - Differential Clock Input: Yes \n"));
+ debug(" - Differential Clock Input: Yes \n");
else
- DP (printf
- (" - Differential Clock Input: No \n"));
+ debug(" - Differential Clock Input: No \n");
if (dimmInfo->redundantRowAddressing == 1)
- DP (printf
- (" - redundant Row Addressing: Yes \n"));
+ debug(" - redundant Row Addressing: Yes \n");
else
- DP (printf
- (" - redundant Row Addressing: No \n"));
+ debug(" - redundant Row Addressing: No \n");
-#endif
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 22: /* Suported AutoPreCharge */
- DP (printf ("\nModul Attributes (SPD Byte 22): \n"));
+ debug("\nModul Attributes (SPD Byte 22): \n");
dimmInfo->suportedEarlyRasPreCharge = data[i] & BIT0;
dimmInfo->suportedAutoPreCharge =
(data[i] & BIT1) >> 1;
(data[i] & BIT4) >> 4;
dimmInfo->suported5PercentUpperVCC =
(data[i] & BIT5) >> 5;
-#ifdef DEBUG
+
if (dimmInfo->suportedEarlyRasPreCharge == 1)
- DP (printf
- (" - Early Ras Precharge: Yes \n"));
+ debug(" - Early Ras Precharge: Yes \n");
else
- DP (printf
- (" - Early Ras Precharge: No \n"));
+ debug(" - Early Ras Precharge: No \n");
if (dimmInfo->suportedAutoPreCharge == 1)
- DP (printf
- (" - AutoPreCharge: Yes \n"));
+ debug(" - AutoPreCharge: Yes \n");
else
- DP (printf
- (" - AutoPreCharge: No \n"));
+ debug(" - AutoPreCharge: No \n");
if (dimmInfo->suportedPreChargeAll == 1)
- DP (printf
- (" - Precharge All: Yes \n"));
+ debug(" - Precharge All: Yes \n");
else
- DP (printf
- (" - Precharge All: No \n"));
+ debug(" - Precharge All: No \n");
if (dimmInfo->suportedWrite1ReadBurst == 1)
- DP (printf
- (" - Write 1/ReadBurst: Yes \n"));
+ debug(" - Write 1/ReadBurst: Yes \n");
else
- DP (printf
- (" - Write 1/ReadBurst: No \n"));
+ debug(" - Write 1/ReadBurst: No \n");
if (dimmInfo->suported5PercentLowVCC == 1)
- DP (printf
- (" - lower VCC tolerance: 5 Percent \n"));
+ debug(" - lower VCC tolerance: 5 Percent \n");
else
- DP (printf
- (" - lower VCC tolerance: 10 Percent \n"));
+ debug(" - lower VCC tolerance: 10 Percent \n");
if (dimmInfo->suported5PercentUpperVCC == 1)
- DP (printf
- (" - upper VCC tolerance: 5 Percent \n"));
+ debug(" - upper VCC tolerance: 5 Percent \n");
else
- DP (printf
- (" - upper VCC tolerance: 10 Percent \n"));
+ debug(" - upper VCC tolerance: 10 Percent \n");
-#endif
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
leftOfPoint;
dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_RoP =
rightOfPoint;
- DP (printf
- ("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n",
- leftOfPoint, rightOfPoint));
+ debug("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n",
+ leftOfPoint, rightOfPoint);
/*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
rightOfPoint = time_tmp % div;
dimmInfo->clockToDataOutMinus1_LoP = leftOfPoint;
dimmInfo->clockToDataOutMinus1_RoP = rightOfPoint;
- DP (printf
- ("Clock To Data Out (2nd CL value): %d.%2d [ns]\n",
- leftOfPoint, rightOfPoint));
+ debug("Clock To Data Out (2nd CL value): %d.%2d [ns]\n",
+ leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
leftOfPoint;
dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_RoP =
rightOfPoint;
- DP (printf
- ("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n",
- leftOfPoint, rightOfPoint));
+ debug("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n",
+ leftOfPoint, rightOfPoint);
/*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
rightOfPoint = time_tmp % div;
dimmInfo->clockToDataOutMinus2_LoP = leftOfPoint;
dimmInfo->clockToDataOutMinus2_RoP = rightOfPoint;
- DP (printf
- ("Clock To Data Out (3rd CL value): %d.%2d [ns]\n",
- leftOfPoint, rightOfPoint));
+ debug("Clock To Data Out (3rd CL value): %d.%2d [ns]\n",
+ leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
trp_clocks =
(dimmInfo->minRowPrechargeTime +
(tmemclk - 1)) / tmemclk;
- DP (printf
- ("*** 1 clock cycle = %ld 10ps intervalls = %ld.%ld ns****\n",
- tmemclk, tmemclk / 100, tmemclk % 100));
- DP (printf
- ("Minimum Row Precharge Time [ns]: %d.%2d = in Clk cycles %d\n",
- leftOfPoint, rightOfPoint, trp_clocks));
+ debug("*** 1 clock cycle = %ld 10ps intervalls = %ld.%ld ns****\n",
+ tmemclk, tmemclk / 100, tmemclk % 100);
+ debug("Minimum Row Precharge Time [ns]: %d.%2d = in Clk cycles %d\n",
+ leftOfPoint, rightOfPoint, trp_clocks);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
rightOfPoint = (data[i] & maskRightOfPoint) * 25;
dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */
- trrd_clocks =
- (dimmInfo->minRowActiveRowActiveDelay +
- (tmemclk - 1)) / tmemclk;
- DP (printf
- ("Minimum Row Active -To- Row Active Delay [ns]: %d.%2d = in Clk cycles %d\n",
- leftOfPoint, rightOfPoint, trp_clocks));
+ debug("Minimum Row Active -To- Row Active Delay [ns]: %d.%2d = in Clk cycles %d\n",
+ leftOfPoint, rightOfPoint, trp_clocks);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
rightOfPoint = (data[i] & maskRightOfPoint) * 25;
dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */
- trcd_clocks =
- (dimmInfo->minRowActiveRowActiveDelay +
- (tmemclk - 1)) / tmemclk;
- DP (printf
- ("Minimum Ras-To-Cas Delay [ns]: %d.%2d = in Clk cycles %d\n",
- leftOfPoint, rightOfPoint, trp_clocks));
+ debug("Minimum Ras-To-Cas Delay [ns]: %d.%2d = in Clk cycles %d\n",
+ leftOfPoint, rightOfPoint, trp_clocks);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
tras_clocks =
(NSto10PS (data[i]) +
(tmemclk - 1)) / tmemclk;
- DP (printf
- ("Minimum Ras Pulse Width [ns]: %d = in Clk cycles %d\n",
- dimmInfo->minRasPulseWidth, tras_clocks));
+ debug("Minimum Ras Pulse Width [ns]: %d = in Clk cycles %d\n",
+ dimmInfo->minRasPulseWidth, tras_clocks);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
case 31: /* Module Bank Density */
dimmInfo->moduleBankDensity = data[i];
- DP (printf
- ("Module Bank Density: %d\n",
- dimmInfo->moduleBankDensity));
+ debug("Module Bank Density: %d\n",
+ dimmInfo->moduleBankDensity);
#ifdef DEBUG
- DP (printf
- ("*** Offered Densities (more than 1 = Multisize-Module): "));
+ debug("*** Offered Densities (more than 1 = Multisize-Module): ");
{
if (dimmInfo->moduleBankDensity & 1)
- DP (printf ("4MB, "));
+ debug("4MB, ");
if (dimmInfo->moduleBankDensity & 2)
- DP (printf ("8MB, "));
+ debug("8MB, ");
if (dimmInfo->moduleBankDensity & 4)
- DP (printf ("16MB, "));
+ debug("16MB, ");
if (dimmInfo->moduleBankDensity & 8)
- DP (printf ("32MB, "));
+ debug("32MB, ");
if (dimmInfo->moduleBankDensity & 16)
- DP (printf ("64MB, "));
+ debug("64MB, ");
if (dimmInfo->moduleBankDensity & 32)
- DP (printf ("128MB, "));
+ debug("128MB, ");
if ((dimmInfo->moduleBankDensity & 64)
|| (dimmInfo->moduleBankDensity & 128)) {
- DP (printf ("ERROR, "));
+ debug("ERROR, ");
hang ();
}
}
- DP (printf ("\n"));
+ debug("\n");
#endif
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
}
dimmInfo->addrAndCommandSetupTime =
(leftOfPoint * 100 + rightOfPoint) * sign;
- DP (printf
- ("Address And Command Setup Time [ns]: %d.%d\n",
- sign * leftOfPoint, rightOfPoint));
+ debug("Address And Command Setup Time [ns]: %d.%d\n",
+ sign * leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
}
dimmInfo->addrAndCommandHoldTime =
(leftOfPoint * 100 + rightOfPoint) * sign;
- DP (printf
- ("Address And Command Hold Time [ns]: %d.%d\n",
- sign * leftOfPoint, rightOfPoint));
+ debug("Address And Command Hold Time [ns]: %d.%d\n",
+ sign * leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
}
dimmInfo->dataInputSetupTime =
(leftOfPoint * 100 + rightOfPoint) * sign;
- DP (printf
- ("Data Input Setup Time [ns]: %d.%d\n",
- sign * leftOfPoint, rightOfPoint));
+ debug("Data Input Setup Time [ns]: %d.%d\n",
+ sign * leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
}
dimmInfo->dataInputHoldTime =
(leftOfPoint * 100 + rightOfPoint) * sign;
- DP (printf
- ("Data Input Hold Time [ns]: %d.%d\n\n",
- sign * leftOfPoint, rightOfPoint));
+ debug("Data Input Hold Time [ns]: %d.%d\n\n",
+ sign * leftOfPoint, rightOfPoint);
break;
/*------------------------------------------------------------------------------------------------------------------------------*/
}
(dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses));
tmp *= dimmInfo->numOfModuleBanks;
tmp *= dimmInfo->sdramWidth;
- tmp = tmp >> 24; /* div by 0x4000000 (64M) */
+ tmp = tmp >> 24; /* div by 0x4000000 (64M) */
dimmInfo->drb_size = (uchar) tmp;
- DP (printf ("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size));
+ debug("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size);
/* try a CAS latency of 3 first... */
cal_val = 4;
}
- DP (printf ("cal_val = %d\n", cal_val * 5));
+ debug("cal_val = %d\n", cal_val * 5);
/* bummer, did't work... */
if (cal_val == 0) {
- DP (printf ("Couldn't find a good CAS latency\n"));
+ debug("Couldn't find a good CAS latency\n");
hang ();
return 0;
}
ulong tmp;
ulong tmp_sdram_mode = 0; /* 0x141c */
ulong tmp_dunit_control_low = 0; /* 0x1404 */
+ uint sdram_config_reg = CONFIG_SYS_SDRAM_CONFIG;
int i;
/* sanity checking */
/* Program the GT with the discovered data */
if (info->registeredAddrAndControlInputs == true)
- DP (printf
- ("Module is registered, but we do not support registered Modules !!!\n"));
-
+ debug("Module is registered, but we do not support registered Modules !!!\n");
/* delay line */
set_dfcdlInit (); /* may be its not needed */
- DP (printf ("Delay line set done\n"));
+ debug("Delay line set done\n");
/* set SDRAM mode NOP */ /* To_do check it */
GT_REG_WRITE (SDRAM_OPERATION, 0x5);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n");
+ }
+
+#ifdef CONFIG_MV64360_ECC
+ if ((info->errorCheckType == 0x2) && (CPCI750_ECC_TEST)) {
+ /* DRAM has ECC, so turn it on */
+ sdram_config_reg |= BIT18;
+ debug("Enabling ECC\n");
}
+#endif /* of ifdef CONFIG_MV64360_ECC */
/* SDRAM configuration */
- GT_REG_WRITE (SDRAM_CONFIG, 0x58200400);
- DP (printf ("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG)));
+ GT_REG_WRITE(SDRAM_CONFIG, sdram_config_reg);
+ debug("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG));
/* SDRAM open pages controll keep open as much as I can */
GT_REG_WRITE (SDRAM_OPEN_PAGES_CONTROL, 0x0);
- DP (printf
- ("sdram_open_pages_controll 0x1414: %08x\n",
- GTREGREAD (SDRAM_OPEN_PAGES_CONTROL)));
+ debug("sdram_open_pages_controll 0x1414: %08x\n",
+ GTREGREAD (SDRAM_OPEN_PAGES_CONTROL));
/* SDRAM D_UNIT_CONTROL_LOW 0x1404 */
tmp = (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x01); /* Clock Domain Sync from power on reset */
if (tmp == 0)
- DP (printf ("Core Signals are sync (by HW-Setting)!!!\n"));
+ debug("Core Signals are sync (by HW-Setting)!!!\n");
else
- DP (printf
- ("Core Signals syncs. are bypassed (by HW-Setting)!!!\n"));
+ debug("Core Signals syncs. are bypassed (by HW-Setting)!!!\n");
/* SDRAM set CAS Lentency according to SPD information */
switch (info->memoryType) {
case SDRAM:
- DP (printf ("### SD-RAM not supported yet !!!\n"));
+ debug("### SD-RAM not supported yet !!!\n");
hang ();
/* ToDo fill SD-RAM if needed !!!!! */
break;
case DDR:
- DP (printf ("### SET-CL for DDR-RAM\n"));
+ debug("### SET-CL for DDR-RAM\n");
switch (info->maxClSupported_DDR) {
case DDR_CL_3:
tmp_dunit_control_low = 0x3c000000; /* Read-Data sampled on falling edge of Clk */
tmp_sdram_mode = 0x32; /* CL=3 Burstlength = 4 */
- DP (printf
- ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
+ debug("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
break;
case DDR_CL_2_5:
if (tmp == 1) { /* clocks sync */
tmp_dunit_control_low = 0x24000000; /* Read-Data sampled on falling edge of Clk */
tmp_sdram_mode = 0x62; /* CL=2,5 Burstlength = 4 */
- DP (printf
- ("Max. CL is 2,5s CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
- } else { /* clk sync. bypassed */
+ debug("Max. CL is 2,5s CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
+ } else { /* clk sync. bypassed */
tmp_dunit_control_low = 0x03000000; /* Read-Data sampled on rising edge of Clk */
tmp_sdram_mode = 0x62; /* CL=2,5 Burstlength = 4 */
- DP (printf
- ("Max. CL is 2,5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
+ debug("Max. CL is 2,5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
}
break;
if (tmp == 1) { /* Sync */
tmp_dunit_control_low = 0x03000000; /* Read-Data sampled on rising edge of Clk */
tmp_sdram_mode = 0x22; /* CL=2 Burstlength = 4 */
- DP (printf
- ("Max. CL is 2s CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
- } else { /* Not sync. */
+ debug("Max. CL is 2s CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
+ } else { /* Not sync. */
tmp_dunit_control_low = 0x3b000000; /* Read-Data sampled on rising edge of Clk */
tmp_sdram_mode = 0x22; /* CL=2 Burstlength = 4 */
- DP (printf
- ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
+ debug("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
}
break;
if (tmp == 1) { /* Sync */
tmp_dunit_control_low = 0x23000000; /* Read-Data sampled on falling edge of Clk */
tmp_sdram_mode = 0x52; /* CL=1,5 Burstlength = 4 */
- DP (printf
- ("Max. CL is 1,5s CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
+ debug("Max. CL is 1,5s CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
} else { /* not sync */
tmp_dunit_control_low = 0x1a000000; /* Read-Data sampled on rising edge of Clk */
tmp_sdram_mode = 0x52; /* CL=1,5 Burstlength = 4 */
- DP (printf
- ("Max. CL is 1,5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
- tmp_sdram_mode, tmp_dunit_control_low));
+ debug("Max. CL is 1,5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low);
}
break;
/* set SDRAM mode SetCommand 0x1418 */
GT_REG_WRITE (SDRAM_OPERATION, 0x3);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n");
}
/* set SDRAM mode SetCommand 0x1418 */
GT_REG_WRITE (SDRAM_OPERATION, 0x3);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n");
}
/*------------------------------------------------------------------------------ */
tmp = 0x02;
- DP (printf ("drb_size (n*64Mbit): %d\n", info->drb_size));
+ debug("drb_size (n*64Mbit): %d\n", info->drb_size);
switch (info->drb_size) {
case 1: /* 64 Mbit */
case 2: /* 128 Mbit */
- DP (printf ("RAM-Device_size 64Mbit or 128Mbit)\n"));
+ debug("RAM-Device_size 64Mbit or 128Mbit)\n");
tmp |= (0x00 << 4);
break;
case 4: /* 256 Mbit */
case 8: /* 512 Mbit */
- DP (printf ("RAM-Device_size 256Mbit or 512Mbit)\n"));
+ debug("RAM-Device_size 256Mbit or 512Mbit)\n");
tmp |= (0x01 << 4);
break;
case 16: /* 1 Gbit */
case 32: /* 2 Gbit */
- DP (printf ("RAM-Device_size 1Gbit or 2Gbit)\n"));
+ debug("RAM-Device_size 1Gbit or 2Gbit)\n");
tmp |= (0x02 << 4);
break;
default:
printf ("Error in dram size calculation\n");
- DP (printf ("Assume: RAM-Device_size 1Gbit or 2Gbit)\n"));
+ debug("Assume: RAM-Device_size 1Gbit or 2Gbit)\n");
tmp |= (0x02 << 4);
return 1;
}
/* SDRAM bank parameters */
/* the param registers for slot 1 (banks 2+3) are offset by 0x8 */
- DP (printf
- ("setting up slot %d config with: %08lx \n", info->slot, tmp));
+ debug("setting up slot %d config with: %08lx \n", info->slot, tmp);
GT_REG_WRITE (SDRAM_ADDR_CONTROL, tmp);
/* ------------------------------------------------------------------------------ */
- DP (printf
- ("setting up sdram_timing_control_low with: %08x \n",
- 0x11511220));
+ debug("setting up sdram_timing_control_low with: %08x \n",
+ 0x11511220);
GT_REG_WRITE (SDRAM_TIMING_CONTROL_LOW, 0x11511220);
if (info->registeredAddrAndControlInputs
|| info->registeredDQMBinputs) {
tmp |= (1 << 17);
- DP (printf
- ("SPD says: registered Addr. and Cont.: %d; registered DQMBinputs: %d\n",
+ debug("SPD says: registered Addr. and Cont.: %d; registered DQMBinputs: %d\n",
info->registeredAddrAndControlInputs,
- info->registeredDQMBinputs));
+ info->registeredDQMBinputs);
}
/* Use buffer 1 to return read data to the CPU
* Page 426 MV64360 */
tmp |= (1 << 26);
- DP (printf
- ("Before Buffer assignment - sdram_conf: %08x\n",
- GTREGREAD (SDRAM_CONFIG)));
- DP (printf
- ("After Buffer assignment - sdram_conf: %08x\n",
- GTREGREAD (SDRAM_CONFIG)));
+ debug("Before Buffer assignment - sdram_conf: %08x\n",
+ GTREGREAD (SDRAM_CONFIG));
+ debug("After Buffer assignment - sdram_conf: %08x\n",
+ GTREGREAD (SDRAM_CONFIG));
/* SDRAM timing To_do: */
tmp = GTREGREAD (SDRAM_TIMING_CONTROL_HIGH);
- DP (printf ("# sdram_timing_control_high is : %08lx \n", tmp));
+ debug("# sdram_timing_control_high is : %08lx \n", tmp);
/* SDRAM address decode register */
/* program this with the default value */
tmp = GTREGREAD (SDRAM_ADDR_CONTROL);
- DP (printf
- ("SDRAM address control (before: decode): %08x ",
- GTREGREAD (SDRAM_ADDR_CONTROL)));
+ debug("SDRAM address control (before: decode): %08x ",
+ GTREGREAD (SDRAM_ADDR_CONTROL));
GT_REG_WRITE (SDRAM_ADDR_CONTROL, (tmp | 0x2));
- DP (printf
- ("SDRAM address control (after: decode): %08x\n",
- GTREGREAD (SDRAM_ADDR_CONTROL)));
+ debug("SDRAM address control (after: decode): %08x\n",
+ GTREGREAD (SDRAM_ADDR_CONTROL));
/* set the SDRAM configuration for each bank */
/* for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) */
{
- int l, l1;
+ int l, l1;
i = info->slot;
- DP (printf
- ("\n*** Running a MRS cycle for bank %d ***\n", i));
+ debug("\n*** Running a MRS cycle for bank %d ***\n", i);
/* map the bank */
memory_map_bank (i, 0, GB / 4);
GT_REG_WRITE (EXTENDED_DRAM_MODE, 0x0);
GT_REG_WRITE (SDRAM_OPERATION, 0x4);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n");
}
GT_REG_WRITE (SDRAM_MODE, tmp | 0x80);
GT_REG_WRITE (SDRAM_OPERATION, 0x3);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n");
}
l1 = 0;
for (l=0;l<200;l++)
- l1 += GTREGREAD (SDRAM_OPERATION);
+ l1 += GTREGREAD (SDRAM_OPERATION);
GT_REG_WRITE (SDRAM_MODE, tmp);
GT_REG_WRITE (SDRAM_OPERATION, 0x3);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n");
}
/* switch back to normal operation mode */
GT_REG_WRITE (SDRAM_OPERATION, 0x5);
while (GTREGREAD (SDRAM_OPERATION) != 0) {
- DP (printf
- ("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+ debug("\n*** SDRAM_OPERATION 1418 after SDRAM_MODE: Module still busy ... please wait... ***\n");
}
#endif /* test only */
for (cnt = STARTVAL/sizeof(long); cnt < maxsize/sizeof(long); cnt <<= 1) {
addr = base + cnt; /* pointer arith! */
- save1=*addr; /* save contents of addr */
- save2=*b; /* save contents of base */
+ save1 = *addr; /* save contents of addr */
+ save2 = *b; /* save contents of base */
*addr=cnt; /* write cnt to addr */
*b=0; /* put null at base */
*b=save2;
if (val != cnt) {
- DP(printf("Found %08x at Address %08x (failure)\n", (unsigned int)val, (unsigned int) addr));
+ debug("Found %08x at Address %08x (failure)\n", (unsigned int)val, (unsigned int) addr);
/* fix boundary condition.. STARTVAL means zero */
if(cnt==STARTVAL/sizeof(long)) cnt=0;
return (cnt * sizeof(long));
return maxsize;
}
-/* ------------------------------------------------------------------------- */
+#ifdef CONFIG_MV64360_ECC
+/*
+ * mv_dma_is_channel_active:
+ * Checks if a engine is busy.
+ */
+int mv_dma_is_channel_active(int engine)
+{
+ ulong data;
+
+ data = GTREGREAD(MV64360_DMA_CHANNEL0_CONTROL + 4 * engine);
+ if (data & BIT14) /* activity status */
+ return 1;
+
+ return 0;
+}
+
+/*
+ * mv_dma_set_memory_space:
+ * Set a DMA memory window for the DMA's address decoding map.
+ */
+int mv_dma_set_memory_space(ulong mem_space, ulong mem_space_target,
+ ulong mem_space_attr, ulong base_address,
+ ulong size)
+{
+ ulong temp;
+
+ /* The base address must be aligned to the size. */
+ if (base_address % size != 0)
+ return 0;
+
+ if (size >= 0x10000) {
+ size &= 0xffff0000;
+ base_address = (base_address & 0xffff0000);
+ /* Set the new attributes */
+ GT_REG_WRITE(MV64360_DMA_BASE_ADDR_REG0 + mem_space * 8,
+ (base_address | mem_space_target |
+ mem_space_attr));
+ GT_REG_WRITE((MV64360_DMA_SIZE_REG0 + mem_space * 8),
+ (size - 1) & 0xffff0000);
+ temp = GTREGREAD(MV64360_DMA_BASE_ADDR_ENABLE_REG);
+ GT_REG_WRITE(DMA_BASE_ADDR_ENABLE_REG,
+ (temp & ~(BIT0 << mem_space)));
+ return 1;
+ }
+
+ return 0;
+}
+
+
+/*
+ * mv_dma_transfer:
+ * Transfer data from source_addr to dest_addr on one of the 4 DMA channels.
+ */
+int mv_dma_transfer(int engine, ulong source_addr,
+ ulong dest_addr, ulong bytes, ulong command)
+{
+ ulong eng_off_reg; /* Engine Offset Register */
+
+ if (bytes > 0xffff)
+ command = command | BIT31; /* DMA_16M_DESCRIPTOR_MODE */
+
+ command = command | ((command >> 6) & 0x7);
+ eng_off_reg = engine * 4;
+ GT_REG_WRITE(MV64360_DMA_CHANNEL0_BYTE_COUNT + eng_off_reg,
+ bytes);
+ GT_REG_WRITE(MV64360_DMA_CHANNEL0_SOURCE_ADDR + eng_off_reg,
+ source_addr);
+ GT_REG_WRITE(MV64360_DMA_CHANNEL0_DESTINATION_ADDR + eng_off_reg,
+ dest_addr);
+ command |= BIT12 /* DMA_CHANNEL_ENABLE */
+ | BIT9; /* DMA_NON_CHAIN_MODE */
+
+ /* Activate DMA engine By writting to mv_dma_control_register */
+ GT_REG_WRITE(MV64360_DMA_CHANNEL0_CONTROL + eng_off_reg, command);
+
+ return 1;
+}
+#endif /* of ifdef CONFIG_MV64360_ECC */
/* ppcboot interface function to SDRAM init - this is where all the
* controlling logic happens */
-long int
+phys_size_t
initdram(int board_type)
{
- int s0 = 0, s1 = 0;
int checkbank[4] = { [0 ... 3] = 0 };
- ulong bank_no, realsize, total, check;
+ ulong realsize, total, check;
AUX_MEM_DIMM_INFO dimmInfo1;
AUX_MEM_DIMM_INFO dimmInfo2;
- int nhr;
+ int bank_no, nhr;
+#ifdef CONFIG_MV64360_ECC
+ ulong dest, mem_space_attr;
+#endif /* of ifdef CONFIG_MV64360_ECC */
/* first, use the SPD to get info about the SDRAM/ DDRRAM */
printf("Skipping SD- DDRRAM setup due to NHR bit being set\n");
} else {
/* DIMM0 */
- s0 = check_dimm(0, &dimmInfo1);
+ (void)check_dimm(0, &dimmInfo1);
/* DIMM1 */
- s1 = check_dimm(1, &dimmInfo2);
+ (void)check_dimm(1, &dimmInfo2);
memory_map_bank(0, 0, 0);
memory_map_bank(1, 0, 0);
if (dimmInfo2.numOfModuleBanks > 2)
printf("Error, SPD claims DIMM2 has >2 banks\n");
- for (bank_no = 0; bank_no < CFG_DRAM_BANKS; bank_no++) {
+ for (bank_no = 0; bank_no < CONFIG_SYS_DRAM_BANKS; bank_no++) {
/* skip over banks that are not populated */
if (! checkbank[bank_no])
continue;
- if ((total + check) > CFG_GT_REGS)
- check = CFG_GT_REGS - total;
+ if ((total + check) > CONFIG_SYS_GT_REGS)
+ check = CONFIG_SYS_GT_REGS - total;
memory_map_bank(bank_no, total, check);
realsize = dram_size((long int *)total, check);
memory_map_bank(bank_no, total, realsize);
+#ifdef CONFIG_MV64360_ECC
+ if (((dimmInfo1.errorCheckType != 0) &&
+ ((dimmInfo2.errorCheckType != 0) ||
+ (dimmInfo2.numOfModuleBanks == 0))) &&
+ (CPCI750_ECC_TEST)) {
+ printf("ECC Initialization of Bank %d:", bank_no);
+ mem_space_attr = ((~(BIT0 << bank_no)) & 0xf) << 8;
+ mv_dma_set_memory_space(0, 0, mem_space_attr, total,
+ realsize);
+ for (dest = total; dest < total + realsize;
+ dest += _8M) {
+ mv_dma_transfer(0, total, dest, _8M,
+ BIT8 | /* DMA_DTL_128BYTES */
+ BIT3 | /* DMA_HOLD_SOURCE_ADDR */
+ BIT11); /* DMA_BLOCK_TRANSFER_MODE */
+ while (mv_dma_is_channel_active(0))
+ ;
+ }
+ printf(" PASS\n");
+ }
+#endif /* of ifdef CONFIG_MV64360_ECC */
+
total += realsize;
}
}
/* ***************************************************************************************
-! * SDRAM INIT *
-! * This procedure detect all Sdram types: 64, 128, 256, 512 Mbit, 1Gbit and 2Gb *
-! * This procedure fits only the Atlantis *
-! * *
+! * SDRAM INIT *
+! * This procedure detect all Sdram types: 64, 128, 256, 512 Mbit, 1Gbit and 2Gb *
+! * This procedure fits only the Atlantis *
+! * *
! *************************************************************************************** */
/* ***************************************************************************************
-! * DFCDL initialize MV643xx Design Considerations *
-! * *
+! * DFCDL initialize MV643xx Design Considerations *
+! * *
! *************************************************************************************** */
int set_dfcdlInit (void)
{
return (0);
}
+
+int do_show_ecc(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ unsigned int ecc_counter;
+ unsigned int ecc_addr;
+
+ GT_REG_READ(0x1458, &ecc_counter);
+ GT_REG_READ(0x1450, &ecc_addr);
+ GT_REG_WRITE(0x1450, 0);
+
+ printf("Error Counter since Reset: %8d\n", ecc_counter);
+ printf("Last error address :0x%08x (" , ecc_addr & 0xfffffff8);
+ if (ecc_addr & 0x01)
+ printf("double");
+ else
+ printf("single");
+ printf(" bit) at DDR-RAM CS#%d\n", ((ecc_addr & 0x6) >> 1));
+
+ return 0;
+}
+
+
+U_BOOT_CMD(
+ show_ecc, 1, 1, do_show_ecc,
+ "Show Marvell MV64360 ECC Info",
+ "Show Marvell MV64360 ECC Counter and last error."
+);