* define the configuration needed by the board are defined in a
* board structure in arch/ppc/platforms (though I do not
* discount the possibility that other architectures could one
- * day be supported. One assumption the driver currently makes
- * is that the PHY is configured in such a way to advertise all
- * capabilities. This is a sensible default, and on certain
- * PHYs, changing this default encounters substantial errata
- * issues. Future versions may remove this requirement, but for
- * now, it is best for the firmware to ensure this is the case.
+ * day be supported.
*
* The Gianfar Ethernet Controller uses a ring of buffer
* descriptors. The beginning is indicated by a register
* corresponding bit in the IMASK register is also set (if
* interrupt coalescing is active, then the interrupt may not
* happen immediately, but will wait until either a set number
- * of frames or amount of time have passed.). In NAPI, the
+ * of frames or amount of time have passed). In NAPI, the
* interrupt handler will signal there is work to be done, and
* exit. Without NAPI, the packet(s) will be handled
* immediately. Both methods will start at the last known empty
#include <linux/sched.h>
#include <linux/string.h>
#include <linux/errno.h>
+#include <linux/unistd.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/if_vlan.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/udp.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/dma-mapping.h>
#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
#include "gianfar.h"
-#include "gianfar_phy.h"
+#include "gianfar_mii.h"
#define TX_TIMEOUT (1*HZ)
#define SKB_ALLOC_TIMEOUT 1000000
#endif
const char gfar_driver_name[] = "Gianfar Ethernet";
-const char gfar_driver_version[] = "1.1";
+const char gfar_driver_version[] = "1.2";
-int startup_gfar(struct net_device *dev);
static int gfar_enet_open(struct net_device *dev);
static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev);
static void gfar_timeout(struct net_device *dev);
static int gfar_change_mtu(struct net_device *dev, int new_mtu);
static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs);
static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs);
-static irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs);
static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs);
-static void gfar_phy_change(void *data);
-static void gfar_phy_timer(unsigned long data);
static void adjust_link(struct net_device *dev);
static void init_registers(struct net_device *dev);
static int init_phy(struct net_device *dev);
-static int gfar_probe(struct device *device);
-static int gfar_remove(struct device *device);
-void free_skb_resources(struct gfar_private *priv);
+static int gfar_probe(struct platform_device *pdev);
+static int gfar_remove(struct platform_device *pdev);
+static void free_skb_resources(struct gfar_private *priv);
static void gfar_set_multi(struct net_device *dev);
static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr);
#ifdef CONFIG_GFAR_NAPI
#endif
int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit);
static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int length);
-static void gfar_phy_startup_timer(unsigned long data);
static void gfar_vlan_rx_register(struct net_device *netdev,
struct vlan_group *grp);
static void gfar_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
else
return 0;
}
-static int gfar_probe(struct device *device)
+
+/* Set up the ethernet device structure, private data,
+ * and anything else we need before we start */
+static int gfar_probe(struct platform_device *pdev)
{
u32 tempval;
struct net_device *dev = NULL;
struct gfar_private *priv = NULL;
- struct platform_device *pdev = to_platform_device(device);
struct gianfar_platform_data *einfo;
struct resource *r;
int idx;
einfo = (struct gianfar_platform_data *) pdev->dev.platform_data;
- if (einfo == NULL) {
+ if (NULL == einfo) {
printk(KERN_ERR "gfar %d: Missing additional data!\n",
pdev->id);
/* Create an ethernet device instance */
dev = alloc_etherdev(sizeof (*priv));
- if (dev == NULL)
+ if (NULL == dev)
return -ENOMEM;
priv = netdev_priv(dev);
priv->regs = (struct gfar *)
ioremap(r->start, sizeof (struct gfar));
- if (priv->regs == NULL) {
+ if (NULL == priv->regs) {
err = -ENOMEM;
goto regs_fail;
}
- /* Set the PHY base address */
- priv->phyregs = (struct gfar *)
- ioremap(einfo->phy_reg_addr, sizeof (struct gfar));
-
- if (priv->phyregs == NULL) {
- err = -ENOMEM;
- goto phy_regs_fail;
- }
-
spin_lock_init(&priv->lock);
- dev_set_drvdata(device, dev);
+ platform_set_drvdata(pdev, dev);
/* Stop the DMA engine now, in case it was running before */
/* (The firmware could have used it, and left it running). */
dev->base_addr = (unsigned long) (priv->regs);
SET_MODULE_OWNER(dev);
- SET_NETDEV_DEV(dev, device);
+ SET_NETDEV_DEV(dev, &pdev->dev);
/* Fill in the dev structure */
dev->open = gfar_enet_open;
return 0;
register_fail:
- iounmap((void *) priv->phyregs);
-phy_regs_fail:
iounmap((void *) priv->regs);
regs_fail:
free_netdev(dev);
- return -ENOMEM;
+ return err;
}
-static int gfar_remove(struct device *device)
+static int gfar_remove(struct platform_device *pdev)
{
- struct net_device *dev = dev_get_drvdata(device);
+ struct net_device *dev = platform_get_drvdata(pdev);
struct gfar_private *priv = netdev_priv(dev);
- dev_set_drvdata(device, NULL);
+ platform_set_drvdata(pdev, NULL);
iounmap((void *) priv->regs);
- iounmap((void *) priv->phyregs);
free_netdev(dev);
return 0;
}
-/* Configure the PHY for dev.
- * returns 0 if success. -1 if failure
+/* Initializes driver's PHY state, and attaches to the PHY.
+ * Returns 0 on success.
*/
static int init_phy(struct net_device *dev)
{
struct gfar_private *priv = netdev_priv(dev);
- struct phy_info *curphy;
- unsigned int timeout = PHY_INIT_TIMEOUT;
- struct gfar *phyregs = priv->phyregs;
- struct gfar_mii_info *mii_info;
- int err;
+ uint gigabit_support =
+ priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
+ SUPPORTED_1000baseT_Full : 0;
+ struct phy_device *phydev;
priv->oldlink = 0;
priv->oldspeed = 0;
priv->oldduplex = -1;
- mii_info = kmalloc(sizeof(struct gfar_mii_info),
- GFP_KERNEL);
-
- if(NULL == mii_info) {
- if (netif_msg_ifup(priv))
- printk(KERN_ERR "%s: Could not allocate mii_info\n",
- dev->name);
- return -ENOMEM;
- }
-
- mii_info->speed = SPEED_1000;
- mii_info->duplex = DUPLEX_FULL;
- mii_info->pause = 0;
- mii_info->link = 1;
-
- mii_info->advertising = (ADVERTISED_10baseT_Half |
- ADVERTISED_10baseT_Full |
- ADVERTISED_100baseT_Half |
- ADVERTISED_100baseT_Full |
- ADVERTISED_1000baseT_Full);
- mii_info->autoneg = 1;
+ phydev = phy_connect(dev, priv->einfo->bus_id, &adjust_link, 0);
- spin_lock_init(&mii_info->mdio_lock);
-
- mii_info->mii_id = priv->einfo->phyid;
-
- mii_info->dev = dev;
-
- mii_info->mdio_read = &read_phy_reg;
- mii_info->mdio_write = &write_phy_reg;
-
- priv->mii_info = mii_info;
-
- /* Reset the management interface */
- gfar_write(&phyregs->miimcfg, MIIMCFG_RESET);
-
- /* Setup the MII Mgmt clock speed */
- gfar_write(&phyregs->miimcfg, MIIMCFG_INIT_VALUE);
-
- /* Wait until the bus is free */
- while ((gfar_read(&phyregs->miimind) & MIIMIND_BUSY) &&
- timeout--)
- cpu_relax();
-
- if(timeout <= 0) {
- printk(KERN_ERR "%s: The MII Bus is stuck!\n",
- dev->name);
- err = -1;
- goto bus_fail;
- }
-
- /* get info for this PHY */
- curphy = get_phy_info(priv->mii_info);
-
- if (curphy == NULL) {
- if (netif_msg_ifup(priv))
- printk(KERN_ERR "%s: No PHY found\n", dev->name);
- err = -1;
- goto no_phy;
+ if (IS_ERR(phydev)) {
+ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+ return PTR_ERR(phydev);
}
- mii_info->phyinfo = curphy;
+ /* Remove any features not supported by the controller */
+ phydev->supported &= (GFAR_SUPPORTED | gigabit_support);
+ phydev->advertising = phydev->supported;
- /* Run the commands which initialize the PHY */
- if(curphy->init) {
- err = curphy->init(priv->mii_info);
-
- if (err)
- goto phy_init_fail;
- }
+ priv->phydev = phydev;
return 0;
-
-phy_init_fail:
-no_phy:
-bus_fail:
- kfree(mii_info);
-
- return err;
}
static void init_registers(struct net_device *dev)
struct gfar *regs = priv->regs;
unsigned long flags;
+ phy_stop(priv->phydev);
+
/* Lock it down */
spin_lock_irqsave(&priv->lock, flags);
- /* Tell the kernel the link is down */
- priv->mii_info->link = 0;
- adjust_link(dev);
-
gfar_halt(dev);
- if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
- /* Clear any pending interrupts */
- mii_clear_phy_interrupt(priv->mii_info);
-
- /* Disable PHY Interrupts */
- mii_configure_phy_interrupt(priv->mii_info,
- MII_INTERRUPT_DISABLED);
- }
-
spin_unlock_irqrestore(&priv->lock, flags);
/* Free the IRQs */
free_irq(priv->interruptTransmit, dev);
free_irq(priv->interruptReceive, dev);
} else {
- free_irq(priv->interruptTransmit, dev);
- }
-
- if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
- free_irq(priv->einfo->interruptPHY, dev);
- } else {
- del_timer_sync(&priv->phy_info_timer);
+ free_irq(priv->interruptTransmit, dev);
}
free_skb_resources(priv);
/* If there are any tx skbs or rx skbs still around, free them.
* Then free tx_skbuff and rx_skbuff */
-void free_skb_resources(struct gfar_private *priv)
+static void free_skb_resources(struct gfar_private *priv)
{
struct rxbd8 *rxbdp;
struct txbd8 *txbdp;
(struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
priv->tx_ring_size, GFP_KERNEL);
- if (priv->tx_skbuff == NULL) {
+ if (NULL == priv->tx_skbuff) {
if (netif_msg_ifup(priv))
printk(KERN_ERR "%s: Could not allocate tx_skbuff\n",
dev->name);
(struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
priv->rx_ring_size, GFP_KERNEL);
- if (priv->rx_skbuff == NULL) {
+ if (NULL == priv->rx_skbuff) {
if (netif_msg_ifup(priv))
printk(KERN_ERR "%s: Could not allocate rx_skbuff\n",
dev->name);
}
}
- /* Set up the PHY change work queue */
- INIT_WORK(&priv->tq, gfar_phy_change, dev);
-
- init_timer(&priv->phy_info_timer);
- priv->phy_info_timer.function = &gfar_phy_startup_timer;
- priv->phy_info_timer.data = (unsigned long) priv->mii_info;
- mod_timer(&priv->phy_info_timer, jiffies + HZ);
+ phy_start(priv->phydev);
/* Configure the coalescing support */
if (priv->txcoalescing)
priv->tx_bd_base,
gfar_read(®s->tbase0));
- if (priv->mii_info->phyinfo->close)
- priv->mii_info->phyinfo->close(priv->mii_info);
-
- kfree(priv->mii_info);
-
return err;
}
txbdp->status &= TXBD_WRAP;
/* Set up checksumming */
- if ((dev->features & NETIF_F_IP_CSUM)
+ if ((dev->features & NETIF_F_IP_CSUM)
&& (CHECKSUM_HW == skb->ip_summed)) {
fcb = gfar_add_fcb(skb, txbdp);
gfar_tx_checksum(skb, fcb);
struct gfar_private *priv = netdev_priv(dev);
stop_gfar(dev);
- /* Shutdown the PHY */
- if (priv->mii_info->phyinfo->close)
- priv->mii_info->phyinfo->close(priv->mii_info);
-
- kfree(priv->mii_info);
+ /* Disconnect from the PHY */
+ phy_disconnect(priv->phydev);
+ priv->phydev = NULL;
netif_stop_queue(dev);
while ((!skb) && timeout--)
skb = dev_alloc_skb(priv->rx_buffer_size + RXBUF_ALIGNMENT);
- if (skb == NULL)
+ if (NULL == skb)
return NULL;
/* We need the data buffer to be aligned properly. We will reserve
struct gfar_private *priv = netdev_priv(dev);
struct rxfcb *fcb = NULL;
- if (skb == NULL) {
+ if (NULL == skb) {
if (netif_msg_rx_err(priv))
printk(KERN_WARNING "%s: Missing skb!!.\n", dev->name);
priv->stats.rx_dropped++;
return IRQ_HANDLED;
}
-static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
- struct net_device *dev = (struct net_device *) dev_id;
- struct gfar_private *priv = netdev_priv(dev);
-
- /* Clear the interrupt */
- mii_clear_phy_interrupt(priv->mii_info);
-
- /* Disable PHY interrupts */
- mii_configure_phy_interrupt(priv->mii_info,
- MII_INTERRUPT_DISABLED);
-
- /* Schedule the phy change */
- schedule_work(&priv->tq);
-
- return IRQ_HANDLED;
-}
-
-/* Scheduled by the phy_interrupt/timer to handle PHY changes */
-static void gfar_phy_change(void *data)
-{
- struct net_device *dev = (struct net_device *) data;
- struct gfar_private *priv = netdev_priv(dev);
- int result = 0;
-
- /* Delay to give the PHY a chance to change the
- * register state */
- msleep(1);
-
- /* Update the link, speed, duplex */
- result = priv->mii_info->phyinfo->read_status(priv->mii_info);
-
- /* Adjust the known status as long as the link
- * isn't still coming up */
- if((0 == result) || (priv->mii_info->link == 0))
- adjust_link(dev);
-
- /* Reenable interrupts, if needed */
- if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR)
- mii_configure_phy_interrupt(priv->mii_info,
- MII_INTERRUPT_ENABLED);
-}
-
-/* Called every so often on systems that don't interrupt
- * the core for PHY changes */
-static void gfar_phy_timer(unsigned long data)
-{
- struct net_device *dev = (struct net_device *) data;
- struct gfar_private *priv = netdev_priv(dev);
-
- schedule_work(&priv->tq);
-
- mod_timer(&priv->phy_info_timer, jiffies +
- GFAR_PHY_CHANGE_TIME * HZ);
-}
-
-/* Keep trying aneg for some time
- * If, after GFAR_AN_TIMEOUT seconds, it has not
- * finished, we switch to forced.
- * Either way, once the process has completed, we either
- * request the interrupt, or switch the timer over to
- * using gfar_phy_timer to check status */
-static void gfar_phy_startup_timer(unsigned long data)
-{
- int result;
- static int secondary = GFAR_AN_TIMEOUT;
- struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data;
- struct gfar_private *priv = netdev_priv(mii_info->dev);
-
- /* Configure the Auto-negotiation */
- result = mii_info->phyinfo->config_aneg(mii_info);
-
- /* If autonegotiation failed to start, and
- * we haven't timed out, reset the timer, and return */
- if (result && secondary--) {
- mod_timer(&priv->phy_info_timer, jiffies + HZ);
- return;
- } else if (result) {
- /* Couldn't start autonegotiation.
- * Try switching to forced */
- mii_info->autoneg = 0;
- result = mii_info->phyinfo->config_aneg(mii_info);
-
- /* Forcing failed! Give up */
- if(result) {
- if (netif_msg_link(priv))
- printk(KERN_ERR "%s: Forcing failed!\n",
- mii_info->dev->name);
- return;
- }
- }
-
- /* Kill the timer so it can be restarted */
- del_timer_sync(&priv->phy_info_timer);
-
- /* Grab the PHY interrupt, if necessary/possible */
- if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) {
- if (request_irq(priv->einfo->interruptPHY,
- phy_interrupt,
- SA_SHIRQ,
- "phy_interrupt",
- mii_info->dev) < 0) {
- if (netif_msg_intr(priv))
- printk(KERN_ERR "%s: Can't get IRQ %d (PHY)\n",
- mii_info->dev->name,
- priv->einfo->interruptPHY);
- } else {
- mii_configure_phy_interrupt(priv->mii_info,
- MII_INTERRUPT_ENABLED);
- return;
- }
- }
-
- /* Start the timer again, this time in order to
- * handle a change in status */
- init_timer(&priv->phy_info_timer);
- priv->phy_info_timer.function = &gfar_phy_timer;
- priv->phy_info_timer.data = (unsigned long) mii_info->dev;
- mod_timer(&priv->phy_info_timer, jiffies +
- GFAR_PHY_CHANGE_TIME * HZ);
-}
-
/* Called every time the controller might need to be made
* aware of new link state. The PHY code conveys this
- * information through variables in the priv structure, and this
+ * information through variables in the phydev structure, and this
* function converts those variables into the appropriate
* register values, and can bring down the device if needed.
*/
{
struct gfar_private *priv = netdev_priv(dev);
struct gfar *regs = priv->regs;
- u32 tempval;
- struct gfar_mii_info *mii_info = priv->mii_info;
+ unsigned long flags;
+ struct phy_device *phydev = priv->phydev;
+ int new_state = 0;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ if (phydev->link) {
+ u32 tempval = gfar_read(®s->maccfg2);
- if (mii_info->link) {
/* Now we make sure that we can be in full duplex mode.
* If not, we operate in half-duplex mode. */
- if (mii_info->duplex != priv->oldduplex) {
- if (!(mii_info->duplex)) {
- tempval = gfar_read(®s->maccfg2);
+ if (phydev->duplex != priv->oldduplex) {
+ new_state = 1;
+ if (!(phydev->duplex))
tempval &= ~(MACCFG2_FULL_DUPLEX);
- gfar_write(®s->maccfg2, tempval);
-
- if (netif_msg_link(priv))
- printk(KERN_INFO "%s: Half Duplex\n",
- dev->name);
- } else {
- tempval = gfar_read(®s->maccfg2);
+ else
tempval |= MACCFG2_FULL_DUPLEX;
- gfar_write(®s->maccfg2, tempval);
- if (netif_msg_link(priv))
- printk(KERN_INFO "%s: Full Duplex\n",
- dev->name);
- }
-
- priv->oldduplex = mii_info->duplex;
+ priv->oldduplex = phydev->duplex;
}
- if (mii_info->speed != priv->oldspeed) {
- switch (mii_info->speed) {
+ if (phydev->speed != priv->oldspeed) {
+ new_state = 1;
+ switch (phydev->speed) {
case 1000:
- tempval = gfar_read(®s->maccfg2);
tempval =
((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII);
- gfar_write(®s->maccfg2, tempval);
break;
case 100:
case 10:
- tempval = gfar_read(®s->maccfg2);
tempval =
((tempval & ~(MACCFG2_IF)) | MACCFG2_MII);
- gfar_write(®s->maccfg2, tempval);
break;
default:
if (netif_msg_link(priv))
printk(KERN_WARNING
- "%s: Ack! Speed (%d) is not 10/100/1000!\n",
- dev->name, mii_info->speed);
+ "%s: Ack! Speed (%d) is not 10/100/1000!\n",
+ dev->name, phydev->speed);
break;
}
- if (netif_msg_link(priv))
- printk(KERN_INFO "%s: Speed %dBT\n", dev->name,
- mii_info->speed);
-
- priv->oldspeed = mii_info->speed;
+ priv->oldspeed = phydev->speed;
}
+ gfar_write(®s->maccfg2, tempval);
+
if (!priv->oldlink) {
- if (netif_msg_link(priv))
- printk(KERN_INFO "%s: Link is up\n", dev->name);
+ new_state = 1;
priv->oldlink = 1;
- netif_carrier_on(dev);
netif_schedule(dev);
}
- } else {
- if (priv->oldlink) {
- if (netif_msg_link(priv))
- printk(KERN_INFO "%s: Link is down\n",
- dev->name);
- priv->oldlink = 0;
- priv->oldspeed = 0;
- priv->oldduplex = -1;
- netif_carrier_off(dev);
- }
+ } else if (priv->oldlink) {
+ new_state = 1;
+ priv->oldlink = 0;
+ priv->oldspeed = 0;
+ priv->oldduplex = -1;
}
-}
+ if (new_state && netif_msg_link(priv))
+ phy_print_status(phydev);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+}
/* Update the hash table based on the current list of multicast
* addresses we subscribe to. Also, change the promiscuity of
}
/* Structure for a device driver */
-static struct device_driver gfar_driver = {
- .name = "fsl-gianfar",
- .bus = &platform_bus_type,
+static struct platform_driver gfar_driver = {
.probe = gfar_probe,
.remove = gfar_remove,
+ .driver = {
+ .name = "fsl-gianfar",
+ },
};
static int __init gfar_init(void)
{
- return driver_register(&gfar_driver);
+ int err = gfar_mdio_init();
+
+ if (err)
+ return err;
+
+ err = platform_driver_register(&gfar_driver);
+
+ if (err)
+ gfar_mdio_exit();
+
+ return err;
}
static void __exit gfar_exit(void)
{
- driver_unregister(&gfar_driver);
+ platform_driver_unregister(&gfar_driver);
+ gfar_mdio_exit();
}
module_init(gfar_init);
projects / karo-tx-linux.git / blobdiff