MODULE_AUTHOR("Stephen Street");
MODULE_DESCRIPTION("PXA2xx SSP SPI Controller");
MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pxa2xx-spi");
#define MAX_BUSES 3
-#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
-#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
-#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0)
+#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
+#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
+#define IS_DMA_ALIGNED(x) (((x) & 0x07) == 0)
+#define MAX_DMA_LEN 8191
-/* for testing SSCR1 changes that require SSP restart, basically
- * everything except the service and interrupt enables */
-#define SSCR1_CHANGE_MASK (SSCR1_TTELP | SSCR1_TTE | SSCR1_EBCEI | SSCR1_SCFR \
+/*
+ * for testing SSCR1 changes that require SSP restart, basically
+ * everything except the service and interrupt enables, the pxa270 developer
+ * manual says only SSCR1_SCFR, SSCR1_SPH, SSCR1_SPO need to be in this
+ * list, but the PXA255 dev man says all bits without really meaning the
+ * service and interrupt enables
+ */
+#define SSCR1_CHANGE_MASK (SSCR1_TTELP | SSCR1_TTE | SSCR1_SCFR \
| SSCR1_ECRA | SSCR1_ECRB | SSCR1_SCLKDIR \
- | SSCR1_RWOT | SSCR1_TRAIL | SSCR1_PINTE \
- | SSCR1_STRF | SSCR1_EFWR |SSCR1_RFT \
- | SSCR1_TFT | SSCR1_SPH | SSCR1_SPO | SSCR1_LBM)
+ | SSCR1_SFRMDIR | SSCR1_RWOT | SSCR1_TRAIL \
+ | SSCR1_IFS | SSCR1_STRF | SSCR1_EFWR \
+ | SSCR1_RFT | SSCR1_TFT | SSCR1_MWDS \
+ | SSCR1_SPH | SSCR1_SPO | SSCR1_LBM)
#define DEFINE_SSP_REG(reg, off) \
static inline u32 read_##reg(void *p) { return __raw_readl(p + (off)); } \
udelay(previous->delay_usecs);
}
- /* Check transfer length */
- if (transfer->len > 8191)
- {
- dev_warn(&drv_data->pdev->dev, "pump_transfers: transfer "
- "length greater than 8191\n");
- message->status = -EINVAL;
- giveback(drv_data);
- return;
+ /* Check for transfers that need multiple DMA segments */
+ if (transfer->len > MAX_DMA_LEN && chip->enable_dma) {
+
+ /* reject already-mapped transfers; PIO won't always work */
+ if (message->is_dma_mapped
+ || transfer->rx_dma || transfer->tx_dma) {
+ dev_err(&drv_data->pdev->dev,
+ "pump_transfers: mapped transfer length "
+ "of %lu is greater than %d\n",
+ transfer->len, MAX_DMA_LEN);
+ message->status = -EINVAL;
+ giveback(drv_data);
+ return;
+ }
+
+ /* warn ... we force this to PIO mode */
+ if (printk_ratelimit())
+ dev_warn(&message->spi->dev, "pump_transfers: "
+ "DMA disabled for transfer length %ld "
+ "greater than %d\n",
+ (long)drv_data->len, MAX_DMA_LEN);
}
/* Setup the transfer state based on the type of transfer */
&dma_thresh))
if (printk_ratelimit())
dev_warn(&message->spi->dev,
- "pump_transfer: "
+ "pump_transfers: "
"DMA burst size reduced to "
"match bits_per_word\n");
}
message->state = RUNNING_STATE;
- /* Try to map dma buffer and do a dma transfer if successful */
- if ((drv_data->dma_mapped = map_dma_buffers(drv_data))) {
+ /* Try to map dma buffer and do a dma transfer if successful, but
+ * only if the length is non-zero and less than MAX_DMA_LEN.
+ *
+ * Zero-length non-descriptor DMA is illegal on PXA2xx; force use
+ * of PIO instead. Care is needed above because the transfer may
+ * have have been passed with buffers that are already dma mapped.
+ * A zero-length transfer in PIO mode will not try to write/read
+ * to/from the buffers
+ *
+ * REVISIT large transfers are exactly where we most want to be
+ * using DMA. If this happens much, split those transfers into
+ * multiple DMA segments rather than forcing PIO.
+ */
+ drv_data->dma_mapped = 0;
+ if (drv_data->len > 0 && drv_data->len <= MAX_DMA_LEN)
+ drv_data->dma_mapped = map_dma_buffers(drv_data);
+ if (drv_data->dma_mapped) {
/* Ensure we have the correct interrupt handler */
drv_data->transfer_handler = dma_transfer;
if (drv_data->ssp_type == PXA25x_SSP)
DCMD(drv_data->tx_channel) |= DCMD_ENDIRQEN;
- /* Fix me, need to handle cs polarity */
- drv_data->cs_control(PXA2XX_CS_ASSERT);
-
/* Clear status and start DMA engine */
cr1 = chip->cr1 | dma_thresh | drv_data->dma_cr1;
write_SSSR(drv_data->clear_sr, reg);
/* Ensure we have the correct interrupt handler */
drv_data->transfer_handler = interrupt_transfer;
- /* Fix me, need to handle cs polarity */
- drv_data->cs_control(PXA2XX_CS_ASSERT);
-
/* Clear status */
cr1 = chip->cr1 | chip->threshold | drv_data->int_cr1;
write_SSSR(drv_data->clear_sr, reg);
|| (read_SSCR1(reg) & SSCR1_CHANGE_MASK) !=
(cr1 & SSCR1_CHANGE_MASK)) {
+ /* stop the SSP, and update the other bits */
write_SSCR0(cr0 & ~SSCR0_SSE, reg);
if (drv_data->ssp_type != PXA25x_SSP)
write_SSTO(chip->timeout, reg);
- write_SSCR1(cr1, reg);
+ /* first set CR1 without interrupt and service enables */
+ write_SSCR1(cr1 & SSCR1_CHANGE_MASK, reg);
+ /* restart the SSP */
write_SSCR0(cr0, reg);
+
} else {
if (drv_data->ssp_type != PXA25x_SSP)
write_SSTO(chip->timeout, reg);
- write_SSCR1(cr1, reg);
}
+
+ /* FIXME, need to handle cs polarity,
+ * this driver uses struct pxa2xx_spi_chip.cs_control to
+ * specify a CS handling function, and it ignores most
+ * struct spi_device.mode[s], including SPI_CS_HIGH */
+ drv_data->cs_control(PXA2XX_CS_ASSERT);
+
+ /* after chip select, release the data by enabling service
+ * requests and interrupts, without changing any mode bits */
+ write_SSCR1(cr1, reg);
}
static void pump_messages(struct work_struct *work)
}
#ifdef CONFIG_PM
-static int suspend_devices(struct device *dev, void *pm_message)
-{
- pm_message_t *state = pm_message;
-
- if (dev->power.power_state.event != state->event) {
- dev_warn(dev, "pm state does not match request\n");
- return -1;
- }
-
- return 0;
-}
static int pxa2xx_spi_suspend(struct platform_device *pdev, pm_message_t state)
{
struct ssp_device *ssp = drv_data->ssp;
int status = 0;
- /* Check all childern for current power state */
- if (device_for_each_child(&pdev->dev, &state, suspend_devices) != 0) {
- dev_warn(&pdev->dev, "suspend aborted\n");
- return -1;
- }
-
status = stop_queue(drv_data);
if (status != 0)
return status;
static struct platform_driver driver = {
.driver = {
.name = "pxa2xx-spi",
- .bus = &platform_bus_type,
.owner = THIS_MODULE,
},
.remove = pxa2xx_spi_remove,
projects / karo-tx-linux.git / blobdiff