i2c, soft-i2c: switch to new multibus/multiadapter support

[karo-tx-uboot.git] / include / configs / DB64360.h

diff --git a/include/configs/DB64360.h b/include/configs/DB64360.h
index daed9342b377f9c4999660cd1e441eafb1611960..d5ef154dba05365fc9bc47db779936ea16b74724 100644 (file)
--- a/include/configs/DB64360.h
+++ b/include/configs/DB64360.h
@@ -120,6 +120,8 @@ if we use PCI it has its own MAC addr */
 
 #define CONFIG_DB64360         1       /* this is an DB64360 board     */
 
+#define        CONFIG_SYS_TEXT_BASE    0xfff00000
+
 #define CONFIG_BAUDRATE                115200  /* console baudrate = 115000    */
 /*ronen - we don't use the global CONFIG_ECC, since in the global ecc we initialize the
        DRAM for ECC in the phase we are relocating to it, which isn't so sufficient.
@@ -138,7 +140,6 @@ if we use PCI it has its own MAC addr */
 /*#define CONFIG_SYS_HUSH_PARSER */
 #undef CONFIG_SYS_HUSH_PARSER
 
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 
 /*
  * The following defines let you select what serial you want to use
@@ -156,7 +157,6 @@ if we use PCI it has its own MAC addr */
 #define CONFIG_MPSC_PORT       0
 
 /* to change the default ethernet port, use this define (options: 0, 1, 2) */
-#define CONFIG_NET_MULTI
 #define MV_ETH_DEVS 2
 
 /* #undef CONFIG_ETHER_PORT_MII         */
@@ -200,7 +200,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define CONFIG_SERIAL          "No. 1"
 #define CONFIG_SERVERIP                10.2.1.126
-#define CONFIG_ROOTPATH /mnt/yellow_dog_mini
+#define CONFIG_ROOTPATH                "/mnt/yellow_dog_mini"
 
 
 #define CONFIG_TESTDRAMDATA    y
@@ -230,7 +230,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
  *
  */
 /* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
 #define CONFIG_JFFS2_DEV               "nor1"
 #define CONFIG_JFFS2_PART_SIZE         0xFFFFFFFF
 #define CONFIG_JFFS2_PART_OFFSET       0x00000000
@@ -242,7 +242,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
  * Note: fake mtd_id's used, no linux mtd map file.
  */
 /*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT         "nor1=db64360-1"
 #define MTDPARTS_DEFAULT       "mtdparts=db64360-1:-(jffs2)"
 */
@@ -318,8 +318,7 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define CONFIG_SYS_HZ                  1000            /* decr freq: 1ms ticks */
 /*ronen - this the Sys clock (cpu bus,internal dram and SDRAM) */
-#define CONFIG_SYS_BUS_HZ              133000000       /* 133 MHz (CPU = 5*Bus = 666MHz)               */
-#define CONFIG_SYS_BUS_CLK             CONFIG_SYS_BUS_HZ
+#define CONFIG_SYS_BUS_CLK             133000000       /* 133 MHz (CPU = 5*Bus = 666MHz)               */
 
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP 7 /* define the SDRAM cycle count */
 #define CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP 50 /* for 400MHZ -> 5.0 ns, for 133MHZ -> 7.50 ns */
@@ -351,9 +350,8 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 */
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0x40000000 /* unused memory region */
-#define CONFIG_SYS_INIT_RAM_END        0x1000
-#define CONFIG_SYS_GBL_DATA_SIZE       128  /* size in bytes reserved for init data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 #define RELOCATE_INTERNAL_RAM_ADDR
 #ifdef RELOCATE_INTERNAL_RAM_ADDR
@@ -594,14 +592,6 @@ ip=${ipaddr}:${serverip}${bootargs_end}; bootm 0x400000;\0"
 
 #define L2_ENABLE      (L2_INIT | L2CR_L2E)
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                  */
-
 #define CONFIG_SYS_BOARD_ASM_INIT      1
 
 #endif /* __CONFIG_H */