#define CONFIG_MCF532x /* define processor family */
#define CONFIG_M5329 /* define processor type */
-#undef DEBUG
-
-#define CONFIG_MCFSERIAL
+#define CONFIG_MCFUART
+#define CONFIG_SYS_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
#undef CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_CACHE | \
- CFG_CMD_DATE | \
- CFG_CMD_ELF | \
- CFG_CMD_FLASH | \
- (CFG_CMD_LOADB | CFG_CMD_LOADS) | \
- CFG_CMD_MEMORY | \
- CFG_CMD_MISC | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO \
- )
-
-#define CFG_UNIFY_CACHE
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#ifdef NANDFLASH_SIZE
+# define CONFIG_CMD_NAND
+#endif
+
+#define CONFIG_SYS_UNIFY_CACHE
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
-# define CONFIG_NET_MULTI 1
+# define CONFIG_NET_MULTI 1
# define CONFIG_MII 1
-# define CFG_DISCOVER_PHY
-# define CFG_RX_ETH_BUFFER 8
-# define CFG_FAULT_ECHO_LINK_DOWN
-
-# define CFG_FEC0_PINMUX 0
-# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
-# define MCFFEC_TOUT_LOOP 50000
-/* If CFG_DISCOVER_PHY is not defined - hardcoded */
-# ifndef CFG_DISCOVER_PHY
+# define CONFIG_MII_INIT 1
+# define CONFIG_SYS_DISCOVER_PHY
+# define CONFIG_SYS_RX_ETH_BUFFER 8
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+# define CONFIG_SYS_FEC0_PINMUX 0
+# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
+# define MCFFEC_TOUT_LOOP 50000
+/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
+# ifndef CONFIG_SYS_DISCOVER_PHY
# define FECDUPLEX FULL
# define FECSPEED _100BASET
# else
-# ifndef CFG_FAULT_ECHO_LINK_DOWN
-# define CFG_FAULT_ECHO_LINK_DOWN
+# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# endif
-# endif /* CFG_DISCOVER_PHY */
+# endif /* CONFIG_SYS_DISCOVER_PHY */
#endif
-#define CONFIG_MCFUART
-#define CFG_UART_PORT (0)
-
#define CONFIG_MCFRTC
#undef RTC_DEBUG
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C /* I2C with hw support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SPEED 80000
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x58000
+#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
+
#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
+#define CONFIG_UDP_CHECKSUM
+
#ifdef CONFIG_MCFFEC
-# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
-# define CONFIG_IPADDR 192.162.1.2
-# define CONFIG_NETMASK 255.255.255.0
-# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
# define CONFIG_GATEWAYIP 192.162.1.1
# define CONFIG_OVERWRITE_ETHADDR_ONCE
#endif /* FEC_ENET */
"save\0" \
""
-#define CONFIG_PRAM 512 /* 512 KB */
-#define CFG_PROMPT "-> "
-#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_PRAM 512 /* 512 KB */
+#define CONFIG_SYS_PROMPT "-> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#ifdef CONFIG_CMD_KGDB
+# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x40010000
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR 0x40010000
-#define CFG_HZ 1000
-#define CFG_CLK 80000000
-#define CFG_CPU_CLK CFG_CLK * 3
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_CLK 80000000
+#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 3
-#define CFG_MBAR 0xFC000000
+#define CONFIG_SYS_MBAR 0xFC000000
+
+#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000)
/*
* Low Level Configuration Settings
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR 0x80000000
-#define CFG_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */
-#define CFG_INIT_RAM_CTRL 0x221
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
+#define CONFIG_SYS_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */
+#define CONFIG_SYS_INIT_RAM_CTRL 0x221
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) - 0x10)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x40000000
-#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
-#define CFG_SDRAM_CFG1 0x53722730
-#define CFG_SDRAM_CFG2 0x56670000
-#define CFG_SDRAM_CTRL 0xE1092000
-#define CFG_SDRAM_EMOD 0x40010000
-#define CFG_SDRAM_MODE 0x018D0000
+#define CONFIG_SYS_SDRAM_BASE 0x40000000
+#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
+#define CONFIG_SYS_SDRAM_CFG1 0x53722730
+#define CONFIG_SYS_SDRAM_CFG2 0x56670000
+#define CONFIG_SYS_SDRAM_CTRL 0xE1092000
+#define CONFIG_SYS_SDRAM_EMOD 0x40010000
+#define CONFIG_SYS_SDRAM_MODE 0x018D0000
-#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400
-#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20)
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
+#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
-#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_BOOTPARAMS_LEN 64*1024
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
+#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_FLASH_CFI
-#ifdef CFG_FLASH_CFI
-# define CFG_FLASH_CFI_DRIVER 1
-# define CFG_FLASH_SIZE 0x800000 /* Max size that the board might have */
-# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
-# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+#define CONFIG_SYS_FLASH_CFI
+#ifdef CONFIG_SYS_FLASH_CFI
+# define CONFIG_FLASH_CFI_DRIVER 1
+# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
+# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+#endif
+
+#ifdef NANDFLASH_SIZE
+# define CONFIG_SYS_MAX_NAND_DEVICE 1
+# define CONFIG_SYS_NAND_BASE CONFIG_SYS_CS2_BASE
+# define CONFIG_SYS_NAND_SIZE 1
+# define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+# define NAND_ALLOW_ERASE_ALL 1
+# define CONFIG_JFFS2_NAND 1
+# define CONFIG_JFFS2_DEV "nand0"
+# define CONFIG_JFFS2_PART_SIZE (CONFIG_SYS_CS2_MASK & ~1)
+# define CONFIG_JFFS2_PART_OFFSET 0x00000000
#endif
-#define CFG_FLASH_BASE 0
-#define CFG_FLASH0_BASE (CFG_CS0_BASE << 16)
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
-#define CFG_ENV_OFFSET 0x4000
-#define CFG_ENV_SECT_SIZE 0x2000
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_IS_EMBEDDED 1
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_SECT_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16
+#define CONFIG_SYS_CACHELINE_SIZE 16
+
+#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_END - 8)
+#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_END - 4)
+#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA)
+#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+ CF_ACR_EN | CF_ACR_SM_ALL)
+#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \
+ CF_CACR_DCM_P)
/*-----------------------------------------------------------------------
* Chipselect bank definitions
* CS4 - Available
* CS5 - Available
*/
-#define CFG_CS0_BASE 0
-#define CFG_CS0_MASK 0x007f0001
-#define CFG_CS0_CTRL 0x00001fa0
+#define CONFIG_SYS_CS0_BASE 0
+#define CONFIG_SYS_CS0_MASK 0x007f0001
+#define CONFIG_SYS_CS0_CTRL 0x00001fa0
-#define CFG_CS1_BASE 0x1000
-#define CFG_CS1_MASK 0x001f0001
-#define CFG_CS1_CTRL 0x002A3780
+#define CONFIG_SYS_CS1_BASE 0x10000000
+#define CONFIG_SYS_CS1_MASK 0x001f0001
+#define CONFIG_SYS_CS1_CTRL 0x002A3780
#ifdef NANDFLASH_SIZE
-#define CFG_CS2_BASE 0x00800000
-#define CFG_CS2_MASK 0x00ff0001
-#define CFG_CS2_CTRL 0x00001f60
+#define CONFIG_SYS_CS2_BASE 0x20000000
+#define CONFIG_SYS_CS2_MASK ((NANDFLASH_SIZE << 20) | 1)
+#define CONFIG_SYS_CS2_CTRL 0x00001f60
#endif
-#define CONFIG_UDP_CHECKSUM
-
#endif /* _M5329EVB_H */
projects / karo-tx-uboot.git / blobdiff