ARM: highbank: remove DRAM bank setup

[karo-tx-uboot.git] / include / configs / csb272.h

diff --git a/include/configs/csb272.h b/include/configs/csb272.h
index 663b8cbd4425bfb7c7c2e75d9cd8318febba2346..71cb5dff366c19f69aa8d7ea1d367064fc712103 100644 (file)
--- a/include/configs/csb272.h
+++ b/include/configs/csb272.h
@@ -2,7 +2,7 @@
  * (C) Copyright 2004
  * Tolunay Orkun, Nextio Inc., torkun@nextio.com
  *
- * SPDX-License-Identifier:    GPL-2.0+ 
+ * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -18,7 +18,6 @@
  */
 
 #define CONFIG_405GP           1       /* This is a PPC405GP CPU       */
-#define CONFIG_4xx             1       /* ...member of PPC4xx family   */
 #define CONFIG_CSB272          1       /* on a Cogent CSB272 board     */
 #define CONFIG_BOARD_EARLY_INIT_F 1    /* Call board_early_init_f()    */
 #define CONFIG_LAST_STAGE_INIT 1       /* Call last_stage_init()       */
@@ -72,8 +71,6 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_ELF
@@ -99,7 +96,6 @@
  */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 /*
@@ -109,7 +105,6 @@
 #undef CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser */
 
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_SYS_PROMPT              "=> "   /* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
 #define        CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 #else
@@ -121,8 +116,6 @@
 
 #define CONFIG_SYS_MEMTEST_START       0x0400000 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define        CONFIG_SYS_HZ                   1000    /* decrementer freq: 1 ms ticks */
 #define CONFIG_SYS_EXTBDINFO           1       /* To use extended board_info (bd_t) */
 #define CONFIG_SYS_LOAD_ADDR           0x100000 /* default load address */
 
@@ -159,10 +152,11 @@
  * I2C configuration
  *
  */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support    */
-#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
-#define CONFIG_SYS_I2C_SPEED           100000  /* I2C speed                    */
-#define CONFIG_SYS_I2C_SLAVE           0x7F    /* I2C slave address            */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0          100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0          0x7F    /* I2C slave address */
 
 /*
  * MII PHY configuration