karo: tx28: explicitly configure pad config (voltage, pull, drive) for all pads

[karo-tx-uboot.git] / include / usb / ulpi.h

diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
index 802f077be4d76add59fc0c85404c0962902ada00..99166c44a08c053386028113952e81acbf3ad24d 100644 (file)
--- a/include/usb/ulpi.h
+++ b/include/usb/ulpi.h
@@ -27,13 +27,24 @@
 #define CONFIG_USB_ULPI_TIMEOUT 1000   /* timeout in us */
 #endif
 
+/*
+ * ulpi view port address and
+ * Port_number that can be passed.
+ * Any additional data to be passed can
+ * be extended from this structure
+ */
+struct ulpi_viewport {
+       u32 viewport_addr;
+       u32 port_num;
+};
+
 /*
  * Initialize the ULPI transciever and check the interface integrity.
- * @ulpi_viewport -  the address of the ULPI viewport register.
+ * @ulpi_vp -  structure containing ULPI viewport data
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_init(u32 ulpi_viewport);
+int ulpi_init(struct ulpi_viewport *ulpi_vp);
 
 /*
  * Select transceiver speed.
@@ -41,7 +52,7 @@ int ulpi_init(u32 ulpi_viewport);
  *                ULPI_FC_LOW_SPEED,  ULPI_FC_FS4LS
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_select_transceiver(u32 ulpi_viewport, unsigned speed);
+int ulpi_select_transceiver(struct ulpi_viewport *ulpi_vp, unsigned speed);
 
 /*
  * Enable/disable VBUS.
@@ -50,14 +61,24 @@ int ulpi_select_transceiver(u32 ulpi_viewport, unsigned speed);
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_enable_vbus(u32 ulpi_viewport, int on, int ext_power, int ext_ind);
+int ulpi_set_vbus(struct ulpi_viewport *ulpi_vp, int on, int ext_power);
+
+/*
+ * Configure VBUS indicator
+ * @external           - external VBUS over-current indicator is used
+ * @passthru           - disables ANDing of internal VBUS comparator
+ *                    with external VBUS input
+ * @complement         - inverts the external VBUS input
+ */
+int ulpi_set_vbus_indicator(struct ulpi_viewport *ulpi_vp, int external,
+                       int passthru, int complement);
 
 /*
  * Enable/disable pull-down resistors on D+ and D- USB lines.
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_set_pd(u32 ulpi_viewport, int enable);
+int ulpi_set_pd(struct ulpi_viewport *ulpi_vp, int enable);
 
 /*
  * Select OpMode.
@@ -66,7 +87,7 @@ int ulpi_set_pd(u32 ulpi_viewport, int enable);
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_opmode_sel(u32 ulpi_viewport, unsigned opmode);
+int ulpi_opmode_sel(struct ulpi_viewport *ulpi_vp, unsigned opmode);
 
 /*
  * Switch to Serial Mode.
@@ -78,7 +99,7 @@ int ulpi_opmode_sel(u32 ulpi_viewport, unsigned opmode);
  * Switches immediately to Serial Mode.
  * To return from Serial Mode, STP line needs to be asserted.
  */
-int ulpi_serial_mode_enable(u32 ulpi_viewport, unsigned smode);
+int ulpi_serial_mode_enable(struct ulpi_viewport *ulpi_vp, unsigned smode);
 
 /*
  * Put PHY into low power mode.
@@ -89,14 +110,14 @@ int ulpi_serial_mode_enable(u32 ulpi_viewport, unsigned smode);
  * STP line must be driven low to keep the PHY in suspend.
  * To resume the PHY, STP line needs to be asserted.
  */
-int ulpi_suspend(u32 ulpi_viewport);
+int ulpi_suspend(struct ulpi_viewport *ulpi_vp);
 
 /*
  * Reset the transceiver. ULPI interface and registers are not affected.
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_reset(u32 ulpi_viewport);
+int ulpi_reset(struct ulpi_viewport *ulpi_vp);
 
 
 /* ULPI access methods below must be implemented for each ULPI viewport. */
@@ -108,7 +129,7 @@ int ulpi_reset(u32 ulpi_viewport);
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_write(u32 ulpi_viewport, u8 *reg, u32 value);
+int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32 value);
 
 /*
  * Read the ULPI PHY register content via the viewport.
@@ -116,14 +137,14 @@ int ulpi_write(u32 ulpi_viewport, u8 *reg, u32 value);
  *
  * returns register content on success, ULPI_ERROR on failure.
  */
-u32 ulpi_read(u32 ulpi_viewport, u8 *reg);
+u32 ulpi_read(struct ulpi_viewport *ulpi_vp, u8 *reg);
 
 /*
  * Wait for the reset to complete.
  * The Link must not attempt to access the PHY until the reset has
  * completed and DIR line is de-asserted.
  */
-int ulpi_reset_wait(u32 ulpi_viewport);
+int ulpi_reset_wait(struct ulpi_viewport *ulpi_vp);
 
 /* Access Extended Register Set (indicator) */
 #define ACCESS_EXT_REGS_OFFSET 0x2f    /* read-write */