X-Git-Url: https://git.kernelconcepts.de/?a=blobdiff_plain;f=README;h=cdbb9de02c68c8ef8ec94be2d2748463b00d2486;hb=5f902cf139559bc436175367a4507b1ddfa4512d;hp=8e1a9ff2c6f3d340d49a560d098353e0905c697a;hpb=e1ccf97c5d7651664d37c0c5aa243874b8851b2d;p=karo-tx-uboot.git

diff --git a/README b/README
index 8e1a9ff2c6..cdbb9de02c 100644
--- a/README
+++ b/README
@@ -164,7 +164,7 @@ Directory Hierarchy:
   /blackfin		Files generic to Analog Devices Blackfin architecture
     /cpu		CPU specific files
     /lib		Architecture specific library files
-  /i386			Files generic to i386 architecture
+  /x86			Files generic to x86 architecture
     /cpu		CPU specific files
     /lib		Architecture specific library files
   /m68k			Files generic to m68k architecture
@@ -319,6 +319,11 @@ The following options need to be configured:
 			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
 			CONFIG_SYS_8272ADS	- MPC8272ADS
 
+- Marvell Family Member
+		CONFIG_SYS_MVFS		- define it if you want to enable
+					  multiple fs option at one time
+					  for marvell soc family
+
 - MPC824X Family Member (if CONFIG_MPC824X is defined)
 		Define exactly one of
 		CONFIG_MPC8240, CONFIG_MPC8245
@@ -620,6 +625,7 @@ The following options need to be configured:
 		CONFIG_CMD_BOOTD	  bootd
 		CONFIG_CMD_CACHE	* icache, dcache
 		CONFIG_CMD_CONSOLE	  coninfo
+		CONFIG_CMD_CRC32	* crc32
 		CONFIG_CMD_DATE		* support for RTC, date/time...
 		CONFIG_CMD_DHCP		* DHCP support
 		CONFIG_CMD_DIAG		* Diagnostics
@@ -632,22 +638,26 @@ The following options need to be configured:
 		CONFIG_CMD_EDITENV	  edit env variable
 		CONFIG_CMD_EEPROM	* EEPROM read/write support
 		CONFIG_CMD_ELF		* bootelf, bootvx
+		CONFIG_CMD_EXPORTENV	* export the environment
 		CONFIG_CMD_SAVEENV	  saveenv
 		CONFIG_CMD_FDC		* Floppy Disk Support
 		CONFIG_CMD_FAT		* FAT partition support
 		CONFIG_CMD_FDOS		* Dos diskette Support
 		CONFIG_CMD_FLASH	  flinfo, erase, protect
 		CONFIG_CMD_FPGA		  FPGA device initialization support
+		CONFIG_CMD_GO		* the 'go' command (exec code)
 		CONFIG_CMD_HWFLOW	* RTS/CTS hw flow control
 		CONFIG_CMD_I2C		* I2C serial bus support
 		CONFIG_CMD_IDE		* IDE harddisk support
 		CONFIG_CMD_IMI		  iminfo
 		CONFIG_CMD_IMLS		  List all found images
 		CONFIG_CMD_IMMAP	* IMMR dump support
+		CONFIG_CMD_IMPORTENV	* import an environment
 		CONFIG_CMD_IRQ		* irqinfo
 		CONFIG_CMD_ITEST	  Integer/string test of 2 values
 		CONFIG_CMD_JFFS2	* JFFS2 Support
 		CONFIG_CMD_KGDB		* kgdb
+		CONFIG_CMD_LDRINFO	  ldrinfo (display Blackfin loader)
 		CONFIG_CMD_LOADB	  loadb
 		CONFIG_CMD_LOADS	  loads
 		CONFIG_CMD_MD5SUM	  print md5 message digest
@@ -675,7 +685,7 @@ The following options need to be configured:
 					  (requires CONFIG_CMD_I2C)
 		CONFIG_CMD_SETGETDCR	  Support for DCR Register access
 					  (4xx only)
-		CONFIG_CMD_SHA1		  print sha1 memory digest
+		CONFIG_CMD_SHA1SUM	  print sha1 memory digest
 					  (requires CONFIG_CMD_MEMORY)
 		CONFIG_CMD_SOURCE	  "source" command Support
 		CONFIG_CMD_SPI		* SPI serial bus support
@@ -738,6 +748,8 @@ The following options need to be configured:
 		CONFIG_RTC_ISL1208	- use Intersil ISL1208 RTC
 		CONFIG_RTC_MAX6900	- use Maxim, Inc. MAX6900 RTC
 		CONFIG_SYS_RTC_DS1337_NOOSC	- Turn off the OSC output for DS1337
+		CONFIG_SYS_RV3029_TCR	- enable trickle charger on
+					  RV3029 RTC.
 
 		Note that if the RTC uses I2C, then the I2C interface
 		must also be configured. See I2C Support, below.
@@ -892,6 +904,18 @@ The following options need to be configured:
 			automatically converts one 32 bit word to two 16 bit
 			words you may also try CONFIG_SMC911X_32_BIT.
 
+		CONFIG_SH_ETHER
+		Support for Renesas on-chip Ethernet controller
+
+			CONFIG_SH_ETHER_USE_PORT
+			Define the number of ports to be used
+
+			CONFIG_SH_ETHER_PHY_ADDR
+			Define the ETH PHY's address
+
+			CONFIG_SH_ETHER_CACHE_WRITEBACK
+			If this option is set, the driver enables cache flush.
+
 - USB Support:
 		At the moment only the UHCI host controller is
 		supported (PIP405, MIP405, MPC5200); define
@@ -1057,6 +1081,28 @@ The following options need to be configured:
 		and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
 		or CONFIG_VIDEO_SED13806_16BPP
 
+		CONFIG_FSL_DIU_FB
+		Enable the Freescale DIU video driver.  Reference boards for
+		SOCs that have a DIU should define this macro to enable DIU
+		support, and should also define these other macros:
+
+			CONFIG_SYS_DIU_ADDR
+			CONFIG_VIDEO
+			CONFIG_CMD_BMP
+			CONFIG_CFB_CONSOLE
+			CONFIG_VIDEO_SW_CURSOR
+			CONFIG_VGA_AS_SINGLE_DEVICE
+			CONFIG_VIDEO_LOGO
+			CONFIG_VIDEO_BMP_LOGO
+
+		The DIU driver will look for the 'monitor' environment variable,
+		and if defined, enable the DIU as a console during boot.  This
+		variable should be set to one of these values:
+
+			'0'	Output video to the DVI connector
+			'1'	Output video to the LVDS connector
+			'2'	Output video to the Dual-Link LVDS connector
+
 - Keyboard Support:
 		CONFIG_KEYBOARD
 
@@ -1648,6 +1694,11 @@ The following options need to be configured:
 		SPI EEPROM, also an instance works with Crystal A/D and
 		D/As on the SACSng board)
 
+		CONFIG_SH_SPI
+
+		Enables the driver for SPI controller on SuperH. Currently
+		only SH7757 is supported.
+
 		CONFIG_SPI_X
 
 		Enables extended (16-bit) SPI EEPROM addressing.
@@ -1952,6 +2003,14 @@ The following options need to be configured:
 		example, some LED's) on your board. At the moment,
 		the following checkpoints are implemented:
 
+- Standalone program support:
+		CONFIG_STANDALONE_LOAD_ADDR
+
+		This option allows to define board specific values
+		for the address where standalone program gets loaded,
+		thus overwriting the architecutre dependent default
+		settings.
+
 Legacy uImage format:
 
   Arg	Where			When