X-Git-Url: https://git.kernelconcepts.de/?a=blobdiff_plain;f=include%2Fconfigs%2FTQM85xx.h;h=abbaf383c75ccd49ab8c03721d57a703b3a71a19;hb=3df4f46f3209c067dcadc969ed02d27c97fa3632;hp=d18f2346c649997dee426f9b2bf57b97bab3390c;hpb=32d4e38eeb5bcc2f854787bfa68bea2b55eaa1d7;p=karo-tx-uboot.git diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index d18f2346c6..abbaf383c7 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -41,14 +41,21 @@ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ +#if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE) +#define CONFIG_TQM8548 +#endif + #define CONFIG_PCI +#ifndef CONFIG_TQM8548_AG +#define CONFIG_PCI1 /* PCI/PCI-X controller */ +#endif +#ifdef CONFIG_TQM8548 +#define CONFIG_PCIE1 /* PCI Express interface */ +#endif + #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */ -#ifdef CONFIG_TQM8548 -#define CONFIG_PCI1 -#define CONFIG_PCIE1 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ -#endif #define CONFIG_TSEC_ENET /* tsec ethernet support */ @@ -70,7 +77,9 @@ * Warning: NAND support will likely increase the U-Boot image size * to more than 256 KB. Please adjust TEXT_BASE if necessary. */ -#undef CONFIG_NAND +#ifdef CONFIG_TQM8548_BE +#define CONFIG_NAND +#endif /* * MPC8540 and MPC8548 don't have CPM module @@ -81,7 +90,9 @@ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -#undef CONFIG_CAN_DRIVER /* CAN Driver support */ +#if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE) +#define CONFIG_CAN_DRIVER /* CAN Driver support */ +#endif /* * sysclk for MPC85xx @@ -106,36 +117,38 @@ */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ +#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00000000 -#define CFG_MEMTEST_END 0x10000000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 +#define CONFIG_SYS_MEMTEST_END 0x10000000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ #ifdef CONFIG_TQM_BIGFLASH -#define CFG_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ #else /* !CONFIG_TQM_BIGFLASH */ -#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ #endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ - -#define CFG_PCI1_ADDR (CFG_CCSRBAR + 0x8000) -#define CFG_PCI2_ADDR (CFG_CCSRBAR + 0x9000) -#define CFG_PCIE1_ADDR (CFG_CCSRBAR + 0xa000) +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ /* * DDR Setup */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#ifdef CONFIG_TQM8548_AG +#define CONFIG_VERY_BIG_RAM +#endif + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 #if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) /* TQM8540 & 8560 need DLL-override */ @@ -148,29 +161,20 @@ #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ #endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */ -/* - * Old TQM85xx boards have 'M' type Spansion Flashes from the S29GLxxxM - * series while new boards have 'N' type Flashes from the S29GLxxxN - * series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB. - */ -#ifdef CONFIG_TQM8548 -#define CONFIG_TQM_FLASH_N_TYPE -#endif /* CONFIG_TQM8548 */ - /* * Flash on the Local Bus */ #ifdef CONFIG_TQM_BIGFLASH -#define CFG_FLASH0 0xE0000000 -#define CFG_FLASH1 0xC0000000 +#define CONFIG_SYS_FLASH0 0xE0000000 +#define CONFIG_SYS_FLASH1 0xC0000000 #else /* !CONFIG_TQM_BIGFLASH */ -#define CFG_FLASH0 0xFC000000 -#define CFG_FLASH1 0xF8000000 +#define CONFIG_SYS_FLASH0 0xFC000000 +#define CONFIG_SYS_FLASH1 0xF8000000 #endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 } +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } -#define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */ -#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ +#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ /* Default ORx timings are for <= 41.7 MHz Local Bus Clock. * @@ -179,7 +183,7 @@ * * For other Local Bus Clocks see following table: * - * Clock/MHz CFG_ORx_PRELIM + * Clock/MHz CONFIG_SYS_ORx_PRELIM * 166 0x.....CA5 * 133 0x.....C85 * 100 0x.....C65 @@ -192,56 +196,55 @@ * */ #ifdef CONFIG_TQM_BIGFLASH -#define CFG_BR0_PRELIM 0xE0001801 /* port size 32bit */ -#define CFG_OR0_PRELIM 0xE0000040 /* 512MB Flash */ -#define CFG_BR1_PRELIM 0xC0001801 /* port size 32bit */ -#define CFG_OR1_PRELIM 0xE0000040 /* 512MB Flash */ +#define CONFIG_SYS_BR0_PRELIM 0xE0001801 /* port size 32bit */ +#define CONFIG_SYS_OR0_PRELIM 0xE0000040 /* 512MB Flash */ +#define CONFIG_SYS_BR1_PRELIM 0xC0001801 /* port size 32bit */ +#define CONFIG_SYS_OR1_PRELIM 0xE0000040 /* 512MB Flash */ #else /* !CONFIG_TQM_BIGFLASH */ -#define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */ -#define CFG_OR0_PRELIM 0xfc000040 /* 64MB Flash */ -#define CFG_BR1_PRELIM 0xf8001801 /* port size 32bit */ -#define CFG_OR1_PRELIM 0xfc000040 /* 64MB Flash */ +#define CONFIG_SYS_BR0_PRELIM 0xfc001801 /* port size 32bit */ +#define CONFIG_SYS_OR0_PRELIM 0xfc000040 /* 64MB Flash */ +#define CONFIG_SYS_BR1_PRELIM 0xf8001801 /* port size 32bit */ +#define CONFIG_SYS_OR1_PRELIM 0xfc000040 /* 64MB Flash */ #endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_FLASH_CFI /* flash is CFI compat. */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */ +#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */ -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ /* * Note: when changing the Local Bus clock divider you have to - * change the timing values in CFG_ORx_PRELIM. + * change the timing values in CONFIG_SYS_ORx_PRELIM. * * LCRR[00:03] CLKDIV: System (CCB) clock divider. Valid values are 2, 4, 8. * LCRR[16:17] EADC : External address delay cycles. It should be set to 2 * for Local Bus Clock > 83.3 MHz. */ -#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ - -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR (CFG_CCSRBAR \ +#define CONFIG_SYS_LBC_LCRR 0x00030008 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ +#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_CCSRBAR \ + 0x04010000) /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */ -#define CFG_MALLOC_LEN (384 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserved for malloc */ /* Serial Port */ #if defined(CONFIG_TQM8560) @@ -254,32 +257,33 @@ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* PS/2 Keyboard */ #define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ #define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ #define CONFIG_PS2SERIAL 2 /* .. on DUART2 */ -#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */ +#define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ #define CONFIG_BOARD_EARLY_INIT_R 1 #endif /* CONFIG_TQM8560 */ #define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ @@ -288,12 +292,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* CAN */ -#define CFG_CAN_BASE (CFG_CCSRBAR \ +#define CONFIG_SYS_CAN_BASE (CONFIG_SYS_CCSRBAR \ + 0x03000000) /* CAN base address */ #ifdef CONFIG_CAN_DRIVER -#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */ -#define CFG_OR2_CAN (CFG_CAN_OR_AM | OR_UPM_BI) -#define CFG_BR2_CAN ((CFG_CAN_BASE & BR_BA) | \ +#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */ +#define CONFIG_SYS_OR2_CAN (CONFIG_SYS_CAN_OR_AM | OR_UPM_BI) +#define CONFIG_SYS_BR2_CAN ((CONFIG_SYS_CAN_BASE & BR_BA) | \ BR_PS_8 | BR_MS_UPMC | BR_V) #endif /* CONFIG_CAN_DRIVER */ @@ -303,89 +307,67 @@ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x48} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 /* I2C RTC */ #define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ /* I2C EEPROM */ /* * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also). */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ /* I2C SYSMON (LM75) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 #ifndef CONFIG_PCIE1 /* RapidIO MMU */ #ifdef CONFIG_TQM_BIGFLASH -#define CFG_RIO_MEM_BASE 0xb0000000 /* base address */ -#define CFG_RIO_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_RIO_MEM_BASE 0xb0000000 /* base address */ +#define CONFIG_SYS_RIO_MEM_SIZE 0x10000000 /* 256M */ #else /* !CONFIG_TQM_BIGFLASH */ -#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ -#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 512M */ #endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE +#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE #endif /* CONFIG_PCIE1 */ /* NAND FLASH */ #ifdef CONFIG_NAND -#undef CFG_NAND_LEGACY - #define CONFIG_NAND_FSL_UPM 1 #define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */ /* address distance between chip selects */ -#define CFG_NAND_SELECT_DEVICE 1 -#define CFG_NAND_CS_DIST 0x200 - -#define CFG_NAND_SIZE 0x8000 -#define CFG_NAND0_BASE (CFG_CCSRBAR + 0x03010000) -#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST) -#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST) -#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST) - -#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ -#define NAND_MAX_CHIPS 1 - -#if (CFG_MAX_NAND_DEVICE == 1) -#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE } -#elif (CFG_MAX_NAND_DEVICE == 2) -#define CFG_NAND_QUIET_TEST 1 -#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ - CFG_NAND1_BASE, \ -} -#elif (CFG_MAX_NAND_DEVICE == 4) -#define CFG_NAND_QUIET_TEST 1 -#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ - CFG_NAND1_BASE, \ - CFG_NAND2_BASE, \ - CFG_NAND3_BASE, \ -} -#endif +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 +#define CONFIG_SYS_NAND_CS_DIST 0x200 + +#define CONFIG_SYS_NAND_SIZE 0x8000 +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_CCSRBAR + 0x03010000) + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define CONFIG_SYS_NAND_MAX_CHIPS 2 /* Number of chips per device */ /* CS3 for NAND Flash */ -#define CFG_BR3_PRELIM ((CFG_NAND0_BASE & BR_BA) | BR_PS_8 | \ - BR_MS_UPMB | BR_V) -#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_NAND_SIZE) | OR_UPM_BI) +#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_NAND_BASE & BR_BA) | \ + BR_PS_8 | BR_MS_UPMB | BR_V) +#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_SIZE) | OR_UPM_BI) -#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ +#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ #endif /* CONFIG_NAND */ @@ -393,17 +375,12 @@ * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE (CFG_CCSRBAR + 0x02000000) -#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ - -/* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BASE (CONFIG_SYS_CCSRBAR + 0x02000000) +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE +#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ #ifdef CONFIG_PCIE1 /* @@ -411,17 +388,17 @@ * Addresses are mapped 1-1. */ #ifdef CONFIG_TQM_BIGFLASH -#define CFG_PCIE1_MEM_BASE 0xb0000000 -#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 512M */ -#define CFG_PCIE1_IO_BASE 0xaf000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xb0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BASE 0xaf000000 #else /* !CONFIG_TQM_BIGFLASH */ -#define CFG_PCIE1_MEM_BASE 0xc0000000 -#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCIE1_IO_BASE 0xef000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BASE 0xef000000 #endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE -#define CFG_PCIE1_IO_PHYS CFG_PCIE1_IO_BASE -#define CFG_PCIE1_IO_SIZE 0x1000000 /* 16M */ +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE +#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BASE +#define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ #endif /* CONFIG_PCIE1 */ #if defined(CONFIG_PCI) @@ -432,7 +409,7 @@ #undef CONFIG_TULIP #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ @@ -526,48 +503,44 @@ #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) #define CONFIG_ETHER_ON_FCC1 -#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \ +#define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \ CMXFCR_TF1CS_MSK) -#define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) -#define CFG_CPMFCR_RAMTYPE 0 -#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) #define CONFIG_ETHER_ON_FCC2 -#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \ +#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \ CMXFCR_TF2CS_MSK) -#define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) -#define CFG_CPMFCR_RAMTYPE 0 -#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) #define CONFIG_ETHER_ON_FCC3 -#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \ +#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \ CMXFCR_TF3CS_MSK) -#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) -#define CFG_CPMFCR_RAMTYPE 0 -#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif /* * Environment */ -#define CFG_ENV_IS_IN_FLASH 1 - -#ifdef CONFIG_TQM_FLASH_N_TYPE -#define CFG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */ -#else /* !CONFIG_TQM_FLASH_N_TYPE */ -#define CFG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */ -#endif /* CONFIG_TQM_FLASH_N_TYPE */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_IS_IN_FLASH 1 + +#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_TIMESTAMP /* Print image info with ts */ @@ -588,14 +561,16 @@ #define CONFIG_JFFS2_NAND 1 -#ifdef CONFIG_JFFS2_CMDLINE +#ifdef CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_FLASH_CFI_MTD #define MTDIDS_DEFAULT "nand0=TQM85xx-nand" #define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-" #else #define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */ #define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ #define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */ -#endif /* CONFIG_JFFS2_CMDLINE */ +#endif /* CONFIG_CMD_MTDPARTS */ #endif /* CONFIG_NAND */ @@ -609,10 +584,13 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_NFS #define CONFIG_CMD_SNTP +#ifndef CONFIG_TQM8548_AG #define CONFIG_CMD_DATE +#endif #define CONFIG_CMD_EEPROM #define CONFIG_CMD_DTT #define CONFIG_CMD_MII +#define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI @@ -623,28 +601,28 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE + \ - sizeof(CFG_PROMPT) + 16) /* Print Buf Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buf Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions @@ -674,20 +652,20 @@ * Setup some board specific values for the default environment variables */ #ifdef CONFIG_CPM2 -#define CFG_ENV_CONSDEV "consdev=ttyCPM0\0" +#define CONFIG_ENV_CONSDEV "consdev=ttyCPM0\0" #else -#define CFG_ENV_CONSDEV "consdev=ttyS0\0" +#define CONFIG_ENV_CONSDEV "consdev=ttyS0\0" #endif -#define CFG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \ +#define CONFIG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \ MK_STR(CONFIG_HOSTNAME)".dtb\0" -#define CFG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0" -#define CFG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \ +#define CONFIG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0" +#define CONFIG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \ "uboot_addr="MK_STR(TEXT_BASE)"\0" #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_ENV_BOOTFILE \ - CFG_ENV_FDT_FILE \ - CFG_ENV_CONSDEV \ + CONFIG_ENV_BOOTFILE \ + CONFIG_ENV_FDT_FILE \ + CONFIG_ENV_CONSDEV \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath\0" \ @@ -711,12 +689,11 @@ "fdt_addr=ffec0000\0" \ "kernel_addr=ffd00000\0" \ "ramdisk_addr=ff800000\0" \ - CFG_ENV_UBOOT \ + CONFIG_ENV_UBOOT \ "load=tftp 100000 $uboot\0" \ "update=protect off $uboot_addr +$filesize;" \ "erase $uboot_addr +$filesize;" \ - "cp.b 100000 $uboot_addr $filesize;" \ - "setenv filesize;saveenv\0" \ + "cp.b 100000 $uboot_addr $filesize" \ "upd=run load update\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self"