pci_hose_write_config_dword(hose, dev, PCI_COMMAND, cmdstat);
}
-#if !(defined(CONFIG_PIP405) || defined (CONFIG_MIP405)) && !(defined (CONFIG_SC3))
+#if !(defined(CONFIG_PIP405) || defined (CONFIG_MIP405))
/*
*As is these functs get called out of flash Not a horrible
config TARGET_SBC405
bool "Support sbc405"
-config TARGET_SC3
- bool "Support sc3"
-
config TARGET_T3CORP
bool "Support t3corp"
source "board/prodrive/alpr/Kconfig"
source "board/prodrive/p3p440/Kconfig"
source "board/sbc405/Kconfig"
-source "board/sc3/Kconfig"
source "board/t3corp/Kconfig"
source "board/xes/xpedite1000/Kconfig"
source "board/xilinx/ml507/Kconfig"
extern int update_flash_size(int flash_size);
#endif
-#if defined(CONFIG_SC3)
-extern void sc3_read_eeprom(void);
-#endif
-
#if defined(CONFIG_CMD_DOC)
void doc_init(void);
#endif
#endif /* CONFIG_405GP, CONFIG_405EP */
#endif /* CONFIG_SYS_EXTBDINFO */
-#if defined(CONFIG_SC3)
- sc3_read_eeprom();
-#endif
-
#if defined(CONFIG_ID_EEPROM) || defined(CONFIG_SYS_I2C_MAC_OFFSET)
mac_read_from_eeprom();
#endif
+++ /dev/null
-if TARGET_SC3
-
-config SYS_BOARD
- default "sc3"
-
-config SYS_CONFIG_NAME
- default "sc3"
-
-endif
+++ /dev/null
-SC3 BOARD
-M: Heiko Schocher <hs@denx.de>
-S: Maintained
-F: board/sc3/
-F: include/configs/sc3.h
-F: configs/sc3_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = sc3.o sc3nand.o
-obj-y += init.o
+++ /dev/null
-/*
- * SPDX-License-Identifier: GPL-2.0 IBM-pibs
- */
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-
-/**
- * ext_bus_cntlr_init - Initializes the External Bus Controller for the external peripherals
- *
- * IMPORTANT: For pass1 this code must run from cache since you can not
- * reliably change a peripheral banks timing register (pbxap) while running
- * code from that bank. For ex., since we are running from ROM on bank 0, we
- * can NOT execute the code that modifies bank 0 timings from ROM, so
- * we run it from cache.
- *
- * Bank 0 - Boot-Flash
- * Bank 1 - NAND-Flash
- * Bank 2 - ISA bus
- * Bank 3 - Second Flash
- * Bank 4 - USB controller
- */
- .globl ext_bus_cntlr_init
-ext_bus_cntlr_init:
-/*
- * We need the current boot up configuration to set correct
- * timings into internal flash and external flash
- */
- mfdcr r24,CPC0_PSR /* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
- 0 0 -> 8 bit external ROM
- 0 1 -> 16 bit internal ROM */
- addi r4,0,2
- srw r24,r24,r4 /* shift right r24 two positions */
- andi. r24,r24,0x06000
-/*
- * All calculations are based on 33MHz EBC clock.
- *
- * First, create a "very slow" timing (~250ns) with burst mode enabled
- * This is need for the external flash access
- */
- lis r25,0x0800
- /* 0000 1000 0xxx 0000 0000 0010 100x xxxx = 0x03800280 */
- ori r25,r25,0x0280
-/*
- * Second, create a fast timing:
- * 90ns first cycle - 3 clock access
- * and 90ns burst cycle, plus 1 clock after the last access
- * This is used for the internal access
- */
- lis r26,0x8900
- /* 1000 1001 0xxx 0000 0000 0010 100x xxxx */
- ori r26,r26,0x0280
-/*
- * We can't change settings on CS# if we currently use them.
- * -> load a few instructions into cache and run this code from cache
- */
- mflr r4 /* save link register */
- bl ..getAddr
-..getAddr:
- mflr r3 /* get address of ..getAddr */
- mtlr r4 /* restore link register */
- addi r4,0,14 /* set ctr to 10; used to prefetch */
- mtctr r4 /* 10 cache lines to fit this function
- in cache (gives us 8x10=80 instructions) */
-..ebcloop:
- icbt r0,r3 /* prefetch cache line for addr in r3 */
- addi r3,r3,32 /* move to next cache line */
- bdnz ..ebcloop /* continue for 10 cache lines */
-/*
- * Delay to ensure all accesses to ROM are complete before changing
- * bank 0 timings. 200usec should be enough.
- * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
- */
- lis r3,0x0
- ori r3,r3,0xA000 /* ensure 200usec have passed since reset */
- mtctr r3
-..spinlp:
- bdnz ..spinlp /* spin loop */
-
-/*-----------------------------------------------------------------------
- * Memory Bank 0 (BOOT-ROM) initialization
- * 0xFFEF00000....0xFFFFFFF
- * We only have to change the timing. Mapping is ok by boot-strapping
- *----------------------------------------------------------------------- */
-
- li r4,PB1AP /* PB0AP=Peripheral Bank 0 Access Parameters */
- mtdcr EBC0_CFGADDR,r4
-
- mr r4,r26 /* assume internal fast flash is boot flash */
- cmpwi r24,0x2000 /* assumption true? ... */
- beq 1f /* ...yes! */
- mr r4,r25 /* ...no, use the slow variant */
- mr r25,r26 /* use this for the other flash */
-1:
- mtdcr EBC0_CFGDATA,r4 /* change timing now */
-
- li r4,PB0CR /* PB0CR=Peripheral Bank 0 Control Register */
- mtdcr EBC0_CFGADDR,r4
- mfdcr r4,EBC0_CFGDATA
- lis r3,0x0001
- ori r3,r3,0x8000 /* allow reads and writes */
- or r4,r4,r3
- mtdcr EBC0_CFGDATA,r4
-
-/*-----------------------------------------------------------------------
- * Memory Bank 3 (Second-Flash) initialization
- * 0xF0000000...0xF01FFFFF -> 2MB
- *----------------------------------------------------------------------- */
-
- li r4,PB3AP /* Peripheral Bank 1 Access Parameter */
- mtdcr EBC0_CFGADDR,r4
- mtdcr EBC0_CFGDATA,r2 /* change timing */
-
- li r4,PB3CR /* Peripheral Bank 1 Configuration Registers */
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0xF003
- ori r4,r4,0x8000
-/*
- * Consider boot configuration
- */
- xori r24,r24,0x2000 /* invert current bus width */
- or r4,r4,r24
- mtdcr EBC0_CFGDATA,r4
-
-/*-----------------------------------------------------------------------
- * Memory Bank 1 (NAND-Flash) initialization
- * 0x77D00000...0x77DFFFFF -> 1MB
- * - the write/read pulse to the NAND can be as short as 25ns, bus the cycle time is always 50ns
- * - the setup time is 0ns
- * - the hold time is 15ns
- * ->
- * - TWT = 0
- * - CSN = 0
- * - OEN = 0
- * - WBN = 0
- * - WBF = 0
- * - TH = 1
- * ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold)
- *----------------------------------------------------------------------- */
-
- li r4,PB1AP /* Peripheral Bank 1 Access Parameter */
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0x0000
- ori r4,r4,0x0200
- mtdcr EBC0_CFGDATA,r4
-
- li r4,PB1CR /* Peripheral Bank 1 Configuration Registers */
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0x77D1
- ori r4,r4,0x8000
- mtdcr EBC0_CFGDATA,r4
-
-
-/* USB init (without acceleration) */
-#ifndef CONFIG_ISP1161_PRESENT
- li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */
- mtdcr EBC0_CFGADDR,r4
- lis r4,0x0180
- ori r4,r4,0x5940
- mtdcr EBC0_CFGDATA,r4
-#endif
-
-/*-----------------------------------------------------------------------
- * Memory Bank 2 (ISA Access) initialization (plus memory bank 6 and 7)
- * 0x78000000...0x7BFFFFFF -> 64 MB
- * Wir arbeiten bei 33 MHz -> 30ns
- *-----------------------------------------------------------------------
-
- A7 (ppc notation) or A24 (standard notation) decides about
- the type of access:
- A7/A24=0 -> memory cycle
- A7/ /A24=1 -> I/O cycle
-*/
- li r4,PB2AP /* PB2AP=Peripheral Bank 2 Access Parameters */
- mtdcr EBC0_CFGADDR,r4
-/*
- We emulate an ISA access
-
- 1. Address active
- 2. wait 0 EBC clocks -> CSN=0
- 3. set CS#
- 4. wait 0 EBC clock -> OEN/WBN=0
- 5. set OE#/WE#
- 6. wait 4 clocks (ca. 90ns) and for Ready signal
- 7. hold for 4 clocks -> TH=4
-*/
-
-#if 1
-/* faster access to isa-bus */
- lis r4,0x0180
- ori r4,r4,0x5940
-#else
- lis r4,0x0100
- ori r4,r4,0x0340
-#endif
- mtdcr EBC0_CFGDATA,r4
-
-#ifdef IDE_USES_ISA_EMULATION
- li r25,PB5AP /* PB5AP=Peripheral Bank 5 Access Parameters */
- mtdcr EBC0_CFGADDR,r25
- mtdcr EBC0_CFGDATA,r4
-#endif
-
- li r25,PB6AP /* PB6AP=Peripheral Bank 6 Access Parameters */
- mtdcr EBC0_CFGADDR,r25
- mtdcr EBC0_CFGDATA,r4
- li r25,PB7AP /* PB7AP=Peripheral Bank 7 Access Parameters */
- mtdcr EBC0_CFGADDR,r25
- mtdcr EBC0_CFGDATA,r4
-
- li r25,PB2CR /* PB2CR=Peripheral Bank 2 Configuration Register */
- mtdcr EBC0_CFGADDR,r25
-
- lis r4,0x780B
- ori r4,r4,0xA000
- mtdcr EBC0_CFGDATA,r4
-/*
- * the other areas are only 1MiB in size
- */
- lis r4,0x7401
- ori r4,r4,0xA000
-
- li r25,PB6CR /* PB6CR=Peripheral Bank 6 Configuration Register */
- mtdcr EBC0_CFGADDR,r25
- lis r4,0x7401
- ori r4,r4,0xA000
- mtdcr EBC0_CFGDATA,r4
-
- li r25,PB7CR /* PB7CR=Peripheral Bank 7 Configuration Register */
- mtdcr EBC0_CFGADDR,r25
- lis r4,0x7411
- ori r4,r4,0xA000
- mtdcr EBC0_CFGDATA,r4
-
-#ifndef CONFIG_ISP1161_PRESENT
- li r25,PB4CR /* PB4CR=Peripheral Bank 4 Configuration Register */
- mtdcr EBC0_CFGADDR,r25
- lis r4,0x7421
- ori r4,r4,0xA000
- mtdcr EBC0_CFGDATA,r4
-#endif
-#ifdef IDE_USES_ISA_EMULATION
- li r25,PB5CR /* PB5CR=Peripheral Bank 5 Configuration Register */
- mtdcr EBC0_CFGADDR,r25
- lis r4,0x0000
- ori r4,r4,0x0000
- mtdcr EBC0_CFGDATA,r4
-#endif
-
-/*-----------------------------------------------------------------------
- * Memory bank 4: USB controller Philips ISP6111
- * 0x77C00000 ... 0x77CFFFFF
- *
- * The chip is connected to:
- * - CPU CS#4
- * - CPU IRQ#2
- * - CPU DMA 3
- *
- * Timing:
- * - command to first data: 300ns. Software must ensure this timing!
- * - Write pulse: 26ns
- * - Read pulse: 33ns
- * - read cycle time: 150ns
- * - write cycle time: 140ns
- *
- * Note: All calculations are based on 33MHz EBC clock. One '#' or '_' is 30ns
- *
- * |- 300ns --|
- * |---- 420ns ---|---- 420ns ---| cycle
- * CS ############:###____#######:###____#######
- * OE ############:####___#######:####___#######
- * WE ############:####__########:####__########
- *
- * ----> 2 clocks RD/WR pulses: 60ns
- * ----> CSN: 3 clock, 90ns
- * ----> OEN: 1 clocks (read cycle)
- * ----> WBN: 1 clocks (write cycle)
- * ----> WBE: 2 clocks
- * ----> TH: 7 clock, 210ns
- * ----> TWT: 7 clocks
- *----------------------------------------------------------------------- */
-
-#ifdef CONFIG_ISP1161_PRESENT
-
- li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0x030D
- ori r4,r4,0x5E80
- mtdcr EBC0_CFGDATA,r4
-
- li r4,PB4CR /* PB2CR=Peripheral Bank 4 Configuration Register */
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0x77C1
- ori r4,r4,0xA000
- mtdcr EBC0_CFGDATA,r4
-
-#endif
-
-#ifndef IDE_USES_ISA_EMULATION
-
-/*-----------------------------------------------------------------------
- * Memory Bank 5 used for IDE access
- *
- * Timings for IDE Interface
- *
- * SETUP / LENGTH / HOLD - cycles valid for 33.3 MHz clk -> 30ns cycle time
- * 70 165 30 PIO-Mode 0, [ns]
- * 3 6 1 [Cycles] ----> AP=0x040C0200
- * 50 125 20 PIO-Mode 1, [ns]
- * 2 5 1 [Cycles] ----> AP=0x03080200
- * 30 100 15 PIO-Mode 2, [ns]
- * 1 4 1 [Cycles] ----> AP=0x02040200
- * 30 80 10 PIO-Mode 3, [ns]
- * 1 3 1 [Cycles] ----> AP=0x01840200
- * 25 70 10 PIO-Mode 4, [ns]
- * 1 3 1 [Cycles] ----> AP=0x01840200
- *
- *----------------------------------------------------------------------- */
-
- li r4,PB5AP
- mtdcr EBC0_CFGADDR,r4
- lis r4,0x040C
- ori r4,r4,0x0200
- mtdcr EBC0_CFGDATA,r4
-
- li r4,PB5CR /* PB2CR=Peripheral Bank 2 Configuration Register */
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0x7A01
- ori r4,r4,0xA000
- mtdcr EBC0_CFGDATA,r4
-#endif
-/*
- * External Peripheral Control Register
- */
- li r4,EBC0_CFG
- mtdcr EBC0_CFGADDR,r4
-
- lis r4,0xB84E
- ori r4,r4,0xF000
- mtdcr EBC0_CFGDATA,r4
-/*
- * drive POST code
- */
- lis r4,0x7900
- ori r4,r4,0x0080
- li r3,0x0001
- stb r3,0(r4) /* 01 -> external bus controller is initialized */
- nop /* pass2 DCR errata #8 */
- blr
+++ /dev/null
-/*
- * (C) Copyright 2007
- * Heiko Schocher, DENX Software Engineering, <hs@denx.de>.
- *
- * (C) Copyright 2003
- * Juergen Beisert, EuroDesign embedded technologies, info@eurodsn.de
- * Derived from walnut.c
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-#include "sc3.h"
-#include <pci.h>
-#include <i2c.h>
-#include <malloc.h>
-#include <netdev.h>
-
-#undef writel
-#undef writeb
-#define writeb(b,addr) ((*(volatile u8 *) (addr)) = (b))
-#define writel(b,addr) ((*(volatile u32 *) (addr)) = (b))
-
-/* write only register to configure things in our CPLD */
-#define CPLD_CONTROL_1 0x79000102
-#define CPLD_VERSION 0x79000103
-
-#define IS_CAMERON ((*(unsigned char *)(CPLD_VERSION)== 0x32) ? 1 : 0)
-
-static struct pci_controller hose={0,};
-
-/************************************************************
- * Standard definition
- ************************************************************/
-
-/* CPC0_CR0 Function ISA bus
- - GPIO0
- - GPIO1 -> Output: NAND-Command Latch Enable
- - GPIO2 -> Output: NAND Address Latch Enable
- - GPIO3 -> IRQ input ISA-IRQ #5 (through CPLD)
- - GPIO4 -> Output: NAND-Chip Enable
- - GPIO5 -> IRQ input ISA-IRQ#7 (through CPLD)
- - GPIO6 -> IRQ input ISA-IRQ#9 (through CPLD)
- - GPIO7 -> IRQ input ISA-IRQ#10 (through CPLD)
- - GPIO8 -> IRQ input ISA-IRQ#11 (through CPLD)
- - GPIO9 -> IRQ input ISA-IRQ#12 (through CPLD)
- - GPIO10/CS1# -> CS1# NAND ISA-CS#0
- - GPIO11/CS2# -> CS2# ISA emulation ISA-CS#1
- - GPIO12/CS3# -> CS3# 2nd Flash-Bank ISA-CS#2 or ISA-CS#7
- - GPIO13/CS4# -> CS4# USB HC or ISA emulation ISA-CS#3
- - GPIO14/CS5# -> CS5# Boosted IDE access ISA-CS#4
- - GPIO15/CS6# -> CS6# ISA emulation ISA-CS#5
- - GPIO16/CS7# -> CS7# ISA emulation ISA-CS#6
- - GPIO17/IRQ0 -> GPIO, in, NAND-Ready/Busy# line ISA-IRQ#3
- - GPIO18/IRQ1 -> IRQ input ISA-IRQ#14
- - GPIO19/IRQ2 -> IRQ input or USB ISA-IRQ#4
- - GPIO20/IRQ3 -> IRQ input PCI-IRQ#D
- - GPIO21/IRQ4 -> IRQ input PCI-IRQ#C
- - GPIO22/IRQ5 -> IRQ input PCI-IRQ#B
- - GPIO23/IRQ6 -> IRQ input PCI-IRQ#A
- - GPIO24 -> if GPIO output: 0=JTAG CPLD activ, 1=JTAG CPLD inactiv
-*/
-/*
-| CPLD register: io-space at offset 0x102 (write only)
-| 0
-| 1
-| 2 0=CS#4 USB CS#, 1=ISA or GP bus
-| 3
-| 4
-| 5
-| 6 1=enable faster IDE access
-| 7
-*/
-#define USB_CHIP_ENABLE 0x04
-#define IDE_BOOSTING 0x40
-
-/* --------------- USB stuff ------------------------------------- */
-#ifdef CONFIG_ISP1161_PRESENT
-/**
- * initUsbHost- Initialize the Philips isp1161 HC part if present
- * @cpldConfig: Pointer to value in write only CPLD register
- *
- * Initialize the USB host controller if present and fills the
- * scratch register to inform the driver about used resources
- */
-
-static void initUsbHost (unsigned char *cpldConfig)
-{
- int i;
- unsigned long usbBase;
- /*
- * Read back where init.S has located the USB chip
- */
- mtdcr (0x012, 0x04);
- usbBase = mfdcr (0x013);
- if (!(usbBase & 0x18000)) /* enabled? */
- return;
- usbBase &= 0xFFF00000;
-
- /*
- * to test for the USB controller enable using of CS#4 and DMA 3 for USB access
- */
- writeb (*cpldConfig | USB_CHIP_ENABLE,CPLD_CONTROL_1);
-
- /*
- * first check: is the controller assembled?
- */
- hcWriteWord (usbBase, 0x5555, HcScratch);
- if (hcReadWord (usbBase, HcScratch) == 0x5555) {
- hcWriteWord (usbBase, 0xAAAA, HcScratch);
- if (hcReadWord (usbBase, HcScratch) == 0xAAAA) {
- if ((hcReadWord (usbBase, HcChipID) & 0xFF00) != 0x6100)
- return; /* this is not our controller */
- /*
- * try a software reset. This needs up to 10 seconds (see datasheet)
- */
- hcWriteDWord (usbBase, 0x00000001, HcCommandStatus);
- for (i = 1000; i > 0; i--) { /* loop up to 10 seconds */
- udelay (10);
- if (!(hcReadDWord (usbBase, HcCommandStatus) & 0x01))
- break;
- }
-
- if (!i)
- return; /* the controller doesn't responding. Broken? */
- /*
- * OK. USB controller is ready. Initialize it in such way the later driver
- * can us it (without any knowing about specific implementation)
- */
- hcWriteDWord (usbBase, 0x00000000, HcControl);
- /*
- * disable all interrupt sources. Because we
- * don't know where we come from (hard reset, cold start, soft reset...)
- */
- hcWriteDWord (usbBase, 0x8000007D, HcInterruptDisable);
- /*
- * our current setup hardware configuration
- * - every port power supply can switched indepently
- * - every port can signal overcurrent
- * - every port is "outside" and the devices are removeable
- */
- hcWriteDWord (usbBase, 0x32000902, HcRhDescriptorA);
- hcWriteDWord (usbBase, 0x00060000, HcRhDescriptorB);
- /*
- * don't forget to switch off power supply of each port
- * The later running driver can reenable them to find and use
- * the (maybe) connected devices.
- *
- */
- hcWriteDWord (usbBase, 0x00000200, HcRhPortStatus1);
- hcWriteDWord (usbBase, 0x00000200, HcRhPortStatus2);
- hcWriteWord (usbBase, 0x0428, HcHardwareConfiguration);
- hcWriteWord (usbBase, 0x0040, HcDMAConfiguration);
- hcWriteWord (usbBase, 0x0000, HcuPInterruptEnable);
- hcWriteWord (usbBase, 0xA000 | (0x03 << 8) | 27, HcScratch);
- /*
- * controller is present and usable
- */
- *cpldConfig |= USB_CHIP_ENABLE;
- }
- }
-}
-#endif
-
-#if defined(CONFIG_START_IDE)
-int board_start_ide(void)
-{
- if (IS_CAMERON) {
- puts ("no IDE on cameron board.\n");
- return 0;
- }
- return 1;
-}
-#endif
-
-static int sc3_cameron_init (void)
-{
- /* Set up the Memory Controller for the CAMERON version */
- mtebc (PB4AP, 0x01805940);
- mtebc (PB4CR, 0x7401a000);
- mtebc (PB5AP, 0x01805940);
- mtebc (PB5CR, 0x7401a000);
- mtebc (PB6AP, 0x0);
- mtebc (PB6CR, 0x0);
- mtebc (PB7AP, 0x0);
- mtebc (PB7CR, 0x0);
- return 0;
-}
-
-void sc3_read_eeprom (void)
-{
- uchar i2c_buffer[18];
-
- i2c_read (0x50, 0x03, 1, i2c_buffer, 9);
- i2c_buffer[9] = 0;
- setenv ("serial#", (char *)i2c_buffer);
-
- /* read mac-address from eeprom */
- i2c_read (0x50, 0x11, 1, i2c_buffer, 15);
- i2c_buffer[17] = 0;
- i2c_buffer[16] = i2c_buffer[14];
- i2c_buffer[15] = i2c_buffer[13];
- i2c_buffer[14] = ':';
- i2c_buffer[13] = i2c_buffer[12];
- i2c_buffer[12] = i2c_buffer[11];
- i2c_buffer[11] = ':';
- i2c_buffer[8] = ':';
- i2c_buffer[5] = ':';
- i2c_buffer[2] = ':';
- setenv ("ethaddr", (char *)i2c_buffer);
-}
-
-int board_early_init_f (void)
-{
- /* write only register to configure things in our CPLD */
- unsigned char cpldConfig_1=0x00;
-
-/*-------------------------------------------------------------------------+
-| Interrupt controller setup for the SolidCard III CPU card (plus Evaluation board).
-|
-| Note: IRQ 0 UART 0, active high; level sensitive
-| IRQ 1 UART 1, active high; level sensitive
-| IRQ 2 IIC, active high; level sensitive
-| IRQ 3 Ext. master, rising edge, edge sensitive
-| IRQ 4 PCI, active high; level sensitive
-| IRQ 5 DMA Channel 0, active high; level sensitive
-| IRQ 6 DMA Channel 1, active high; level sensitive
-| IRQ 7 DMA Channel 2, active high; level sensitive
-| IRQ 8 DMA Channel 3, active high; level sensitive
-| IRQ 9 Ethernet Wakeup, active high; level sensitive
-| IRQ 10 MAL System Error (SERR), active high; level sensitive
-| IRQ 11 MAL Tx End of Buffer, active high; level sensitive
-| IRQ 12 MAL Rx End of Buffer, active high; level sensitive
-| IRQ 13 MAL Tx Descriptor Error, active high; level sensitive
-| IRQ 14 MAL Rx Descriptor Error, active high; level sensitive
-| IRQ 15 Ethernet, active high; level sensitive
-| IRQ 16 External PCI SERR, active high; level sensitive
-| IRQ 17 ECC Correctable Error, active high; level sensitive
-| IRQ 18 PCI Power Management, active high; level sensitive
-|
-| IRQ 19 (EXT IRQ7 405GPr only)
-| IRQ 20 (EXT IRQ8 405GPr only)
-| IRQ 21 (EXT IRQ9 405GPr only)
-| IRQ 22 (EXT IRQ10 405GPr only)
-| IRQ 23 (EXT IRQ11 405GPr only)
-| IRQ 24 (EXT IRQ12 405GPr only)
-|
-| IRQ 25 (EXT IRQ 0) NAND-Flash R/B# (raising edge means flash is ready)
-| IRQ 26 (EXT IRQ 1) IDE0 interrupt (x86 = IRQ14). Active high (edge sensitive)
-| IRQ 27 (EXT IRQ 2) USB controller
-| IRQ 28 (EXT IRQ 3) INT D, VGA; active low; level sensitive
-| IRQ 29 (EXT IRQ 4) INT C, Ethernet; active low; level sensitive
-| IRQ 30 (EXT IRQ 5) INT B, PC104+ SLOT; active low; level sensitive
-| IRQ 31 (EXT IRQ 6) INT A, PC104+ SLOT; active low; level sensitive
-|
-| Direct Memory Access Controller Signal Polarities
-| DRQ0 active high (like ISA)
-| ACK0 active low (like ISA)
-| EOT0 active high (like ISA)
-| DRQ1 active high (like ISA)
-| ACK1 active low (like ISA)
-| EOT1 active high (like ISA)
-| DRQ2 active high (like ISA)
-| ACK2 active low (like ISA)
-| EOT2 active high (like ISA)
-| DRQ3 active high (like ISA)
-| ACK3 active low (like ISA)
-| EOT3 active high (like ISA)
-|
-+-------------------------------------------------------------------------*/
-
- writeb (cpldConfig_1, CPLD_CONTROL_1); /* disable everything in CPLD */
-
- mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
- mtdcr (UIC0ER, 0x00000000); /* disable all ints */
- mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */
-
- if (IS_CAMERON) {
- sc3_cameron_init();
- mtdcr (0x0B6, 0x18000000);
- mtdcr (UIC0PR, 0xFFFFFFF0);
- mtdcr (UIC0TR, 0x10001030);
- } else {
- mtdcr (0x0B6, 0x0000000);
- mtdcr (UIC0PR, 0xFFFFFFE0);
- mtdcr (UIC0TR, 0x10000020);
- }
- mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
- mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
-
- /* setup other implementation specific details */
- mtdcr (CPC0_ECR, 0x60606000);
-
- mtdcr (CPC0_CR1, 0x000042C0);
-
- if (IS_CAMERON) {
- mtdcr (CPC0_CR0, 0x01380000);
- /* Setup the GPIOs */
- writel (0x08008000, 0xEF600700); /* Output states */
- writel (0x00000000, 0xEF600718); /* Open Drain control */
- writel (0x68098000, 0xEF600704); /* Output control */
- } else {
- mtdcr (CPC0_CR0,0x00080000);
- /* Setup the GPIOs */
- writel (0x08000000, 0xEF600700); /* Output states */
- writel (0x14000000, 0xEF600718); /* Open Drain control */
- writel (0x7C000000, 0xEF600704); /* Output control */
- }
-
- /* Code decompression disabled */
- mtdcr (DCP0_CFGADDR, KCONF);
- mtdcr (DCP0_CFGDATA, 0x2B);
-
- /* CPC0_ER: enable sleep mode of (currently) unused components */
- /* CPC0_FR: force unused components into sleep mode */
- mtdcr (CPC0_ER, 0x3F800000);
- mtdcr (CPC0_FR, 0x14000000);
-
- /* set PLB priority */
- mtdcr (PLB0_ACR, 0x08000000);
-
- /* --------------- DMA stuff ------------------------------------- */
- mtdcr (0x126, 0x49200000);
-
-#ifndef IDE_USES_ISA_EMULATION
- cpldConfig_1 |= IDE_BOOSTING; /* enable faster IDE */
- /* cpldConfig |= 0x01; */ /* enable 8.33MHz output, if *not* present on your baseboard */
- writeb (cpldConfig_1, CPLD_CONTROL_1);
-#endif
-
-#ifdef CONFIG_ISP1161_PRESENT
- initUsbHost (&cpldConfig_1);
- writeb (cpldConfig_1, CPLD_CONTROL_1);
-#endif
- /* FIXME: for what must we do this */
- *(unsigned long *)0x79000080 = 0x0001;
- return(0);
-}
-
-int misc_init_r (void)
-{
- char *s1;
- int i, xilinx_val;
- volatile char *xilinx_adr;
- xilinx_adr = (char *)0x79000102;
-
- *xilinx_adr = 0x00;
-
-/* customer settings ***************************************** */
-/*
- s1 = getenv ("function");
- if (s1) {
- if (!strcmp (s1, "Rosho")) {
- printf ("function 'Rosho' activated\n");
- *xilinx_adr = 0x40;
- }
- else {
- printf (">>>>>>>>>> function %s not recognized\n",s1);
- }
- }
-*/
-
-/* individual settings ***************************************** */
- if ((s1 = getenv ("xilinx"))) {
- i=0;
- xilinx_val = 0;
- while (i < 3 && s1[i]) {
- if (s1[i] >= '0' && s1[i] <= '9')
- xilinx_val = (xilinx_val << 4) + s1[i] - '0';
- else
- if (s1[i] >= 'A' && s1[i] <= 'F')
- xilinx_val = (xilinx_val << 4) + s1[i] - 'A' + 10;
- else
- if (s1[i] >= 'a' && s1[i] <= 'f')
- xilinx_val = (xilinx_val << 4) + s1[i] - 'a' + 10;
- else {
- xilinx_val = -1;
- break;
- }
- i++;
- }
- if (xilinx_val >= 0 && xilinx_val <=255 && i < 3) {
- printf ("Xilinx: set to %s\n", s1);
- *xilinx_adr = (unsigned char) xilinx_val;
- } else
- printf ("Xilinx: rejected value %s\n", s1);
- }
- return 0;
-}
-
-/* -------------------------------------------------------------------------
- * printCSConfig
- *
- * Print some informations about chips select configurations
- * Only used while debugging.
- *
- * Params:
- * - No. of CS pin
- * - AP of this CS
- * - CR of this CS
- *
- * Returns
- * nothing
- ------------------------------------------------------------------------- */
-
-#ifdef SC3_DEBUGOUT
-static void printCSConfig(int reg,unsigned long ap,unsigned long cr)
-{
- const char *bsize[4] = {"8","16","32","?"};
- const unsigned char banks[8] = {1, 2, 4, 8, 16, 32, 64, 128};
- const char *bankaccess[4] = {"disabled", "RO", "WO", "RW"};
-
-#define CYCLE 30 /* time of one clock (based on 33MHz) */
-
- printf("\nCS#%d",reg);
- if (!(cr & 0x00018000))
- puts(" unused");
- else {
- if (((cr&0xFFF00000U) & ((banks[(cr & 0x000E0000) >> 17]-1) << 20)))
- puts(" Address is not multiple of bank size!");
-
- printf("\n -%s bit device",
- bsize[(cr & 0x00006000) >> 13]);
- printf(" at 0x%08lX", cr & 0xFFF00000U);
- printf(" size: %u MB", banks[(cr & 0x000E0000) >> 17]);
- printf(" rights: %s", bankaccess[(cr & 0x00018000) >> 15]);
- if (ap & 0x80000000) {
- printf("\n -Burst device (%luns/%luns)",
- (((ap & 0x7C000000) >> 26) + 1) * CYCLE,
- (((ap & 0x03800000) >> 23) + 1) * CYCLE);
- } else {
- printf("\n -Non burst device, active cycle %luns",
- (((ap & 0x7F800000) >> 23) + 1) * CYCLE);
- printf("\n -Address setup %luns",
- ((ap & 0xC0000) >> 18) * CYCLE);
- printf("\n -CS active to RD %luns/WR %luns",
- ((ap & 0x30000) >> 16) * CYCLE,
- ((ap & 0xC000) >> 14) * CYCLE);
- printf("\n -WR to CS inactive %luns",
- ((ap & 0x3000) >> 12) * CYCLE);
- printf("\n -Hold after access %luns",
- ((ap & 0xE00) >> 9) * CYCLE);
- printf("\n -Ready is %sabled",
- ap & 0x100 ? "en" : "dis");
- }
- }
-}
-#endif
-
-#ifdef SC3_DEBUGOUT
-
-static unsigned int ap[] = {PB0AP, PB1AP, PB2AP, PB3AP, PB4AP,
- PB5AP, PB6AP, PB7AP};
-static unsigned int cr[] = {PB0CR, PB1CR, PB2CR, PB3CR, PB4CR,
- PB5CR, PB6CR, PB7CR};
-
-static int show_reg (int nr)
-{
- unsigned long ul1, ul2;
-
- mtdcr (EBC0_CFGADDR, ap[nr]);
- ul1 = mfdcr (EBC0_CFGDATA);
- mtdcr (EBC0_CFGADDR, cr[nr]);
- ul2 = mfdcr(EBC0_CFGDATA);
- printCSConfig(nr, ul1, ul2);
- return 0;
-}
-#endif
-
-int checkboard (void)
-{
-#ifdef SC3_DEBUGOUT
- unsigned long ul1;
- int i;
-
- for (i = 0; i < 8; i++) {
- show_reg (i);
- }
-
- mtdcr (EBC0_CFGADDR, EBC0_CFG);
- ul1 = mfdcr (EBC0_CFGDATA);
-
- puts ("\nGeneral configuration:\n");
-
- if (ul1 & 0x80000000)
- printf(" -External Bus is always driven\n");
-
- if (ul1 & 0x400000)
- printf(" -CS signals are always driven\n");
-
- if (ul1 & 0x20000)
- printf(" -PowerDown after %lu clocks\n",
- (ul1 & 0x1F000) >> 7);
-
- switch (ul1 & 0xC0000)
- {
- case 0xC0000:
- printf(" -No external master present\n");
- break;
- case 0x00000:
- printf(" -8 bit external master present\n");
- break;
- case 0x40000:
- printf(" -16 bit external master present\n");
- break;
- case 0x80000:
- printf(" -32 bit external master present\n");
- break;
- }
-
- switch (ul1 & 0x300000)
- {
- case 0x300000:
- printf(" -Prefetch: Illegal setting!\n");
- break;
- case 0x000000:
- printf(" -1 doubleword prefetch\n");
- break;
- case 0x100000:
- printf(" -2 doublewords prefetch\n");
- break;
- case 0x200000:
- printf(" -4 doublewords prefetch\n");
- break;
- }
- putc ('\n');
-#endif
- printf("Board: SolidCard III %s %s version.\n",
- (IS_CAMERON ? "Cameron" : "Eurodesign"), CONFIG_SC3_VERSION);
- return 0;
-}
-
-static int printSDRAMConfig(char reg, unsigned long cr)
-{
- const int bisize[8]={4, 8, 16, 32, 64, 128, 256, 0};
-#ifdef SC3_DEBUGOUT
- const char *basize[8]=
- {"4", "8", "16", "32", "64", "128", "256", "Reserved"};
-
- printf("SDRAM bank %d",reg);
-
- if (!(cr & 0x01))
- puts(" disabled\n");
- else {
- printf(" at 0x%08lX, size %s MB",cr & 0xFFC00000,basize[(cr&0xE0000)>>17]);
- printf(" mode %lu\n",((cr & 0xE000)>>13)+1);
- }
-#endif
-
- if (cr & 0x01)
- return(bisize[(cr & 0xE0000) >> 17]);
-
- return 0;
-}
-
-#ifdef SC3_DEBUGOUT
-static unsigned int mbcf[] = {SDRAM0_B0CR, SDRAM0_B1CR, SDRAM0_B2CR, SDRAM0_B3CR};
-#endif
-
-phys_size_t initdram (int board_type)
-{
- unsigned int mems=0;
- unsigned long ul1;
-
-#ifdef SC3_DEBUGOUT
- unsigned long ul2;
- int i;
-
- puts("\nSDRAM configuration:\n");
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
- ul1 = mfdcr(SDRAM0_CFGDATA);
-
- if (!(ul1 & 0x80000000)) {
- puts(" Controller disabled\n");
- return 0;
- }
- for (i = 0; i < 4; i++) {
- mtdcr (SDRAM0_CFGADDR, mbcf[i]);
- ul1 = mfdcr (SDRAM0_CFGDATA);
- mems += printSDRAMConfig (i, ul1);
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
- ul1 = mfdcr(SDRAM0_CFGDATA);
-
- printf ("Timing:\n -CAS latency %lu\n", ((ul1 & 0x1800000) >> 23)+1);
- printf (" -Precharge %lu (PTA) \n", ((ul1 & 0xC0000) >> 18) + 1);
- printf (" -R/W to Precharge %lu (CTP)\n", ((ul1 & 0x30000) >> 16) + 1);
- printf (" -Leadoff %lu\n", ((ul1 & 0xC000) >> 14) + 1);
- printf (" -CAS to RAS %lu\n", ((ul1 & 0x1C) >> 2) + 4);
- printf (" -RAS to CAS %lu\n", ((ul1 & 0x3) + 1));
- puts ("Misc:\n");
- mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
- ul1 = mfdcr(SDRAM0_CFGDATA);
- printf (" -Refresh rate: %luns\n", (ul1 >> 16) * 7);
-
- mtdcr(SDRAM0_CFGADDR,SDRAM0_PMIT);
- ul2=mfdcr(SDRAM0_CFGDATA);
-
- mtdcr(SDRAM0_CFGADDR,SDRAM0_CFG);
- ul1=mfdcr(SDRAM0_CFGDATA);
-
- if (ul1 & 0x20000000)
- printf(" -Power Down after: %luns\n",
- ((ul2 & 0xFFC00000) >> 22) * 7);
- else
- puts(" -Power Down disabled\n");
-
- if (ul1 & 0x40000000)
- printf(" -Self refresh feature active\n");
- else
- puts(" -Self refresh disabled\n");
-
- if (ul1 & 0x10000000)
- puts(" -ECC enabled\n");
- else
- puts(" -ECC disabled\n");
-
- if (ul1 & 0x8000000)
- puts(" -Using registered SDRAM\n");
-
- if (!(ul1 & 0x6000000))
- puts(" -Using 32 bit data width\n");
- else
- puts(" -Illegal data width!\n");
-
- if (ul1 & 0x400000)
- puts(" -ECC drivers inactive\n");
- else
- puts(" -ECC drivers active\n");
-
- if (ul1 & 0x200000)
- puts(" -Memory lines always active outputs\n");
- else
- puts(" -Memory lines only at write cycles active outputs\n");
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_STATUS);
- ul1 = mfdcr (SDRAM0_CFGDATA);
- if (ul1 & 0x80000000)
- puts(" -SDRAM Controller ready\n");
- else
- puts(" -SDRAM Controller not ready\n");
-
- if (ul1 & 0x4000000)
- puts(" -SDRAM in self refresh mode!\n");
-
- return (mems * 1024 * 1024);
-#else
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
- ul1 = mfdcr (SDRAM0_CFGDATA);
- mems = printSDRAMConfig (0, ul1);
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
- ul1 = mfdcr (SDRAM0_CFGDATA);
- mems += printSDRAMConfig (1, ul1);
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
- ul1 = mfdcr(SDRAM0_CFGDATA);
- mems += printSDRAMConfig (2, ul1);
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
- ul1 = mfdcr(SDRAM0_CFGDATA);
- mems += printSDRAMConfig (3, ul1);
-
- return (mems * 1024 * 1024);
-#endif
-}
-
-static void pci_solidcard3_fixup_irq (struct pci_controller *hose, pci_dev_t dev)
-{
-/*-------------------------------------------------------------------------+
- | ,-. ,-. ,-. ,-. ,-.
- | INTD# ----|B|-----|P|-. ,-|P|-. ,-| |-. ,-|G|
- | |R| |C| \ / |C| \ / |E| \ / |r|
- | INTC# ----|I|-----|1|-. `/---|1|-. `/---|t|-. `/---|a|
- | |D| |0| \/ |0| \/ |h| \/ |f|
- | INTB# ----|G|-----|4|-./`----|4|-./`----|e|-./`----|i|
- | |E| |+| /\ |+| /\ |r| /\ |k|
- | INTA# ----| |-----| |- `----| |- `----| |- `----| |
- | `-' `-' `-' `-' `-'
- | Slot 0 10 11 12 13
- | REQ# 0 1 2 *
- | GNT# 0 1 2 *
- +-------------------------------------------------------------------------*/
- unsigned char int_line = 0xff;
-
- switch (PCI_DEV(dev)) {
- case 10:
- int_line = 31; /* INT A */
- POST_OUT(0x42);
- break;
-
- case 11:
- int_line = 30; /* INT B */
- POST_OUT(0x43);
- break;
-
- case 12:
- int_line = 29; /* INT C */
- POST_OUT(0x44);
- break;
-
- case 13:
- int_line = 28; /* INT D */
- POST_OUT(0x45);
- break;
- }
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line);
-}
-
-extern void pci_405gp_init(struct pci_controller *hose);
-extern void pci_405gp_fixup_irq(struct pci_controller *hose, pci_dev_t dev);
-extern void pci_405gp_setup_bridge(struct pci_controller *hose, pci_dev_t dev,struct pci_config_table *entry);
-/*
- * The following table is used when there is a special need to setup a PCI device.
- * For every PCI device found in this table is called the given init function with given
- * parameters. So never let all IDs at PCI_ANY_ID. In this case any found device gets the same
- * parameters!
- *
-*/
-static struct pci_config_table pci_solidcard3_config_table[] =
-{
-/* Host to PCI Bridge device (405GP) */
- {
- vendor: 0x1014,
- device: 0x0156,
- class: PCI_CLASS_BRIDGE_HOST,
- bus: 0,
- dev: 0,
- func: 0,
- config_device: pci_405gp_setup_bridge
- },
- { }
-};
-
-/*-------------------------------------------------------------------------+
- | pci_init_board (Called from pci_init() in drivers/pci/pci.c)
- |
- | Init the PCI part of the SolidCard III
- |
- | Params:
- * - Pointer to current PCI hose
- * - Current Device
- *
- * Returns
- * nothing
- +-------------------------------------------------------------------------*/
-
-void pci_init_board(void)
-{
- POST_OUT(0x41);
-/*
- * we want the ptrs to RAM not flash (ie don't use init list)
- */
- hose.fixup_irq = pci_solidcard3_fixup_irq;
- hose.config_table = pci_solidcard3_config_table;
- pci_405gp_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/**
- * hcWriteWord - write a 16 bit value into the USB controller
- * @base: base address to access the chip registers
- * @value: 16 bit value to write into register @offset
- * @offset: register to write the @value into
- *
- */
-static void inline hcWriteWord (unsigned long base, unsigned int value,
- unsigned int offset)
-{
- out_le16 ((volatile u16*)(base + 2), offset | 0x80);
- out_le16 ((volatile u16*)base, value);
-}
-
-/**
- * hcWriteDWord - write a 32 bit value into the USB controller
- * @base: base address to access the chip registers
- * @value: 32 bit value to write into register @offset
- * @offset: register to write the @value into
- *
- */
-
-static void inline hcWriteDWord (unsigned long base, unsigned long value,
- unsigned int offset)
-{
- out_le16 ((volatile u16*)(base + 2), offset | 0x80);
- out_le16 ((volatile u16*)base, value);
- out_le16 ((volatile u16*)base, value >> 16);
-}
-
-/**
- * hcReadWord - read a 16 bit value from the USB controller
- * @base: base address to access the chip registers
- * @offset: register to read from
- *
- * Returns the readed register value
- */
-
-static unsigned int inline hcReadWord (unsigned long base, unsigned int offset)
-{
- out_le16 ((volatile u16*)(base + 2), offset);
- return (in_le16 ((volatile u16*)base));
-}
-
-/**
- * hcReadDWord - read a 32 bit value from the USB controller
- * @base: base address to access the chip registers
- * @offset: register to read from
- *
- * Returns the readed register value
- */
-
-static unsigned long inline hcReadDWord (unsigned long base, unsigned int offset)
-{
- unsigned long val, val16;
-
- out_le16 ((volatile u16*)(base + 2), offset);
- val = in_le16((volatile u16*)base);
- val16 = in_le16((volatile u16*)base);
- return (val | (val16 << 16));
-}
-
-/* control and status registers isp1161 */
-#define HcRevision 0x00
-#define HcControl 0x01
-#define HcCommandStatus 0x02
-#define HcInterruptStatus 0x03
-#define HcInterruptEnable 0x04
-#define HcInterruptDisable 0x05
-#define HcFmInterval 0x0D
-#define HcFmRemaining 0x0E
-#define HcFmNumber 0x0F
-#define HcLSThreshold 0x11
-#define HcRhDescriptorA 0x12
-#define HcRhDescriptorB 0x13
-#define HcRhStatus 0x14
-#define HcRhPortStatus1 0x15
-#define HcRhPortStatus2 0x16
-
-#define HcHardwareConfiguration 0x20
-#define HcDMAConfiguration 0x21
-#define HcTransferCounter 0x22
-#define HcuPInterrupt 0x24
-#define HcuPInterruptEnable 0x25
-#define HcChipID 0x27
-#define HcScratch 0x28
-#define HcSoftwareReset 0x29
-#define HcITLBufferLength 0x2A
-#define HcATLBufferLength 0x2B
-#define HcBufferStatus 0x2C
-#define HcReadBackITL0Length 0x2D
-#define HcReadBackITL1Length 0x2E
-#define HcITLBufferPort 0x40
-#define HcATLBufferPort 0x41
+++ /dev/null
-/*
- * (C) Copyright 2007
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-#include <asm/processor.h>
-
-#define readb(addr) *(volatile u_char *)(addr)
-#define readl(addr) *(volatile u_long *)(addr)
-#define writeb(d,addr) *(volatile u_char *)(addr) = (d)
-
-#define SC3_NAND_ALE 29 /* GPIO PIN 3 */
-#define SC3_NAND_CLE 30 /* GPIO PIN 2 */
-#define SC3_NAND_CE 27 /* GPIO PIN 5 */
-
-static void *sc3_io_base;
-static void *sc3_control_base = (void *)0xEF600700;
-
-static void sc3_nand_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- set_bit (SC3_NAND_CLE, sc3_control_base);
- else
- clear_bit (SC3_NAND_CLE, sc3_control_base);
- if ( ctrl & NAND_ALE )
- set_bit (SC3_NAND_ALE, sc3_control_base);
- else
- clear_bit (SC3_NAND_ALE, sc3_control_base);
- if ( ctrl & NAND_NCE )
- set_bit (SC3_NAND_CE, sc3_control_base);
- else
- clear_bit (SC3_NAND_CE, sc3_control_base);
- }
-
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-
-static int sc3_nand_dev_ready(struct mtd_info *mtd)
-{
- if (!(readl(sc3_control_base + 0x1C) & 0x4000))
- return 0;
- return 1;
-}
-
-static void sc3_select_chip(struct mtd_info *mtd, int chip)
-{
- clear_bit (SC3_NAND_CE, sc3_control_base);
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- nand->ecc.mode = NAND_ECC_SOFT;
-
- sc3_io_base = (void *) CONFIG_SYS_NAND_BASE;
- /* Set address of NAND IO lines (Using Linear Data Access Region) */
- nand->IO_ADDR_R = (void __iomem *) sc3_io_base;
- nand->IO_ADDR_W = (void __iomem *) sc3_io_base;
- /* Reference hardware control function */
- nand->cmd_ctrl = sc3_nand_hwcontrol;
- nand->dev_ready = sc3_nand_dev_ready;
- nand->select_chip = sc3_select_chip;
- return 0;
-}
-#endif
}
#endif
-#ifdef CONFIG_SC3
-/* TODO: with new initcalls, move this into the driver */
-extern void sc3_read_eeprom(void);
-
-static int initr_sc3_read_eeprom(void)
-{
- sc3_read_eeprom();
- return 0;
-}
-#endif
-
static int initr_jumptable(void)
{
jumptable_init();
#endif
INIT_FUNC_WATCHDOG_RESET
initr_secondary_cpu,
-#ifdef CONFIG_SC3
- initr_sc3_read_eeprom,
-#endif
#if defined(CONFIG_ID_EEPROM) || defined(CONFIG_SYS_I2C_MAC_OFFSET)
mac_read_from_eeprom,
#endif
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_SC3=y
+++ /dev/null
-/*
- * (C) Copyright 2007
- * Heiko Schocher, DENX Software Engineering, <hs@denx.de>.
- *
- * From:
- * (C) Copyright 2003
- * Juergen Beisert, EuroDesign embedded technologies, jbeisert@eurodsn.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#undef USE_VGA_GRAPHICS
-
-/* Memory Map
- * 0x00000000 .... 0x03FFFFFF -> RAM (up to 128MiB)
- * 0x74000000 .... 0x740FFFFF -> CS#6
- * 0x74100000 .... 0x741FFFFF -> CS#7
- * 0x74200000 .... 0x742FFFFF -> CS4# if no internal USB
- * 0x74300000 .... 0x743FFFFF -> CS5# if no boosted IDE
- * 0x77C00000 .... 0x77CFFFFF -> CS4# USB HC (1 MiB)
- * 0x77D00000 .... 0x77DFFFFF -> CS1# NAND-Flash (1 MiB)
- * 0x78000000 .... 0x78FFFFFF -> CS2# ISA-Bus Speicherzugriff (16 MiB)
- * 0x79000000 .... 0x7900FFFF -> CS2# ISA-Bus IO-Zugriff (16 MiB, mapped: 64kiB)
- * 0x79010000 .... 0x79FFFFFF -> CS2# ISA-Bus IO-Zugriff (mirrored)
- * 0x7A000000 .... 0x7A0FFFFF -> CS5# IDE emulation (1MiB)
- *
- * 0x80000000 .... 0x9FFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 1:1)
- * 0xA0000000 .... 0xBFFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 0x00000000...0x1FFFFFFF)
- * 0xE8000000 .... 0xE800FFFF -> PCI-Bus IO-Zugriff (64kiB, translated to PCI: 0x0000...0xFFFF)
- * 0xE8800000 .... 0xEBFFFFFF -> PCI-Bus IO-Zugriff (56MiB, translated to PCI: 0x00800000...0x3FFFFFF)
- * 0xEED00000 .... 0xEED00003 -> PCI-Bus
- * 0xEF400000 .... 0xEF40003F -> PCI-Bus Local Configuration Registers
- * 0xEF40003F .... 0xEF5FFFFF -> reserved
- * 0xEF600000 .... 0xEFFFFFFF -> 405GP internal Devices (10 MiB)
- * 0xF0000000 .... 0xF01FFFFF -> Flash-ROM (2 MiB)
- * 0xF0200000 .... 0xF7FFFFFF -> free for flash devices
- * 0xF8000000 .... 0xF8000FFF -> OnChipMemory (4kiB)
- * 0xF8001000 .... 0xFFDFFFFF -> free for flash devices
- * 0xFFE00000 .... 0xFFFFFFFF -> BOOT-ROM (2 MiB)
- */
-
-#define CONFIG_SC3 1
-#define CONFIG_405GP 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */
-
-/*
- * Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range
- * If undefined, IDE access uses a seperat emulation with higher access speed.
- * Consider to inform your Linux IDE driver about the different addresses!
- * IDE_USES_ISA_EMULATION is only used if you define CONFIG_CMD_IDE!
- */
-#define IDE_USES_ISA_EMULATION
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-/*
- * define CONFIG_SYS_CLK_FREQ to your base crystal clock in Hz
- */
-#define CONFIG_SYS_CLK_FREQ 33333333
-
-/*
- * define CONFIG_BAUDRATE to the baudrate value you want to use as default
- */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nand_args=setenv bootargs root=/dev/mtdblock5 rw" \
- "rootfstype=jffs2\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcons=setenv bootargs ${bootargs} " \
- "console=ttyS0,${baudrate}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr}\0" \
- "flash_nand=run nand_args addip addcons;bootm ${kernel_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/sc3/uImage\0" \
- "u-boot=/tftpboot/sc3/u-boot.bin\0" \
- "setup=tftp 200000 /tftpboot/sc3/setup.img;source 200000\0" \
- "kernel_addr=FFE08000\0" \
- ""
-#undef CONFIG_BOOTCOMMAND
-
-#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#if 1 /* feel free to disable for development */
-#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
-#define CONFIG_AUTOBOOT_PROMPT \
- "\nSC3 - booting... stop with ENTER\n"
-#define CONFIG_AUTOBOOT_DELAY_STR "\r" /* 1st "password" */
-#define CONFIG_AUTOBOOT_DELAY_STR2 "\n" /* 1st "password" */
-#endif
-
-/*
- * define CONFIG_BOOTCOMMAND to the autoboot commands. They will running after
- * the CONFIG_BOOTDELAY delay to boot your machine
- */
-#define CONFIG_BOOTCOMMAND "bootp;dcache on;bootm"
-
-/*
- * define CONFIG_BOOTARGS to the default kernel parameters. They will used if you don't
- * set different values at the u-boot prompt
- */
-#ifdef USE_VGA_GRAPHICS
- #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp nfsroot=/tftpboot/solidcard3re"
-#else
- #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs rw ip=bootp"
-#endif
-/*
- * Is the USB host controller assembled? If yes define CONFIG_ISP1161_PRESENT
- * This reserves memory bank #4 for this purpose
- */
-#undef CONFIG_ISP1161_PRESENT
-
-#undef CONFIG_LOADS_ECHO /* no echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/* #define CONFIG_EEPRO100_SROM_WRITE */
-/* #define CONFIG_SHOW_MAC */
-#define CONFIG_EEPRO100
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* add 405GP MII PHY management */
-#define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SOURCE
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
-#define CONFIG_SYS_PROMPT "SC3> " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- * baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- *
- * Consider the OPB clock! If it get lower the BASE_BAUD must be lower to
- * (see 405GP datasheet for descritpion)
- */
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-#define CONFIG_SYS_BASE_BAUD 921600 /* internal clock */
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-/*-----------------------------------------------------------------------
- * IIC stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-
-#define I2C_INIT
-#define I2C_ACTIVE 0
-#define I2C_TRISTATE 0
-
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* mask valid bits */
-
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-/* If you want to see, whats connected to your PCI bus */
-/* #define CONFIG_PCI_SCAN_SHOW */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
-/*-----------------------------------------------------------------------
- * External peripheral base address
- *-----------------------------------------------------------------------
- */
-#if !defined(CONFIG_CMD_IDE)
-
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#else
-#define CONFIG_START_IDE 1 /* check, if use IDE */
-
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-#define CONFIG_ATAPI
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
-
-#ifndef IDE_USES_ISA_EMULATION
-
-/* New and faster access */
-#define CONFIG_SYS_ATA_BASE_ADDR 0x7A000000 /* start of ISA IO emulation */
-
-/* How many IDE busses are available */
-#define CONFIG_SYS_IDE_MAXBUS 1
-
-/* What IDE ports are available */
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x000 /* first is available */
-#undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */
-
-/* access to the data port is calculated:
- CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-
-/* access to the registers is calculated:
- CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-
-/* access to the alternate register is calculated:
- CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x008 /* Offset for alternate registers */
-
-#else /* IDE_USES_ISA_EMULATION */
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0x79000000 /* start of ISA IO emulation */
-
-/* How many IDE busses are available */
-#define CONFIG_SYS_IDE_MAXBUS 1
-
-/* What IDE ports are available */
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* first is available */
-#undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */
-
-/* access to the data port is calculated:
- CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-
-/* access to the registers is calculated:
- CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-
-/* access to the alternate register is calculated:
- CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x03F0 /* Offset for alternate registers */
-
-#endif /* IDE_USES_ISA_EMULATION */
-
-#endif
-
-/*
-#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
-#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
-#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
-*/
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- *
- * CONFIG_SYS_FLASH_BASE -> start address of internal flash
- * CONFIG_SYS_MONITOR_BASE -> start of u-boot
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFE00000
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of U-Boot */
-#define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1)
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MiB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization ## FIXME: lookup in datasheet
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */
-#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_WRITE_SWAPPED_DATA /* swap Databytes between reading/writing */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector in bottom type */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x4000 /* see README - env sector total size */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#endif
-/* let us changing anything in our environment */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * NAND-FLASH stuff
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x77D00000
-
-#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-
-/* No command line, one static partition */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nand0"
-#define CONFIG_JFFS2_PART_SIZE 0x01000000
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/*
- * Init Memory Controller:
- *
- */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE
-#define FLASH_BASE1_PRELIM 0
-
-/*-----------------------------------------------------------------------
- * Some informations about the internal SRAM (OCM=On Chip Memory)
- *
- * CONFIG_SYS_OCM_DATA_ADDR -> location
- * CONFIG_SYS_OCM_DATA_SIZE -> size
-*/
-
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM):
- * - we are using the internal 4k SRAM, so we don't need data cache mapping
- * - internal SRAM (OCM=On Chip Memory) is placed to CONFIG_SYS_OCM_DATA_ADDR
- * - Stackpointer will be located to
- * (CONFIG_SYS_INIT_RAM_ADDR&0xFFFF0000) | (CONFIG_SYS_INIT_SP_OFFSET&0x0000FFFF)
- * in arch/powerpc/cpu/ppc4xx/start.S
- */
-
-#undef CONFIG_SYS_INIT_DCACHE_CS
-/* Where the internal SRAM starts */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR
-/* Where the internal SRAM ends (only offset) */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x0F00
-
-/*
-
- CONFIG_SYS_INIT_RAM_ADDR ------> ------------ lower address
- | |
- | ^ |
- | | |
- | | Stack |
- CONFIG_SYS_GBL_DATA_OFFSET ----> ------------
- | |
- | 64 Bytes |
- | |
- CONFIG_SYS_INIT_RAM_SIZE ------> ------------ higher address
- (offset only)
-
-*/
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-/* Initial value of the stack pointern in internal SRAM */
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* ################################################################################### */
-/* These defines will be used in arch/powerpc/cpu/ppc4xx/cpu_init.c to setup external chip selects */
-/* They are currently undefined cause they are initiaized in board/solidcard3/init.S */
-
-/* This chip select accesses the boot device */
-/* It depends on boot select switch if this device is 16 or 8 bit */
-
-#undef CONFIG_SYS_EBC_PB0AP
-#undef CONFIG_SYS_EBC_PB0CR
-
-#undef CONFIG_SYS_EBC_PB1AP
-#undef CONFIG_SYS_EBC_PB1CR
-
-#undef CONFIG_SYS_EBC_PB2AP
-#undef CONFIG_SYS_EBC_PB2CR
-
-#undef CONFIG_SYS_EBC_PB3AP
-#undef CONFIG_SYS_EBC_PB3CR
-
-#undef CONFIG_SYS_EBC_PB4AP
-#undef CONFIG_SYS_EBC_PB4CR
-
-#undef CONFIG_SYS_EBC_PB5AP
-#undef CONFIG_SYS_EBC_PB5CR
-
-#undef CONFIG_SYS_EBC_PB6AP
-#undef CONFIG_SYS_EBC_PB6CR
-
-#undef CONFIG_SYS_EBC_PB7AP
-#undef CONFIG_SYS_EBC_PB7CR
-
-#define CONFIG_SYS_EBC_CFG 0xb84ef000
-
-#undef CONFIG_SDRAM_BANK0 /* use private SDRAM initialization */
-#undef CONFIG_SPD_EEPROM
-
-/*
- * Define this to get more information about system configuration
- */
-/* #define SC3_DEBUGOUT */
-#undef SC3_DEBUGOUT
-
-/***********************************************************************
- * External peripheral base address
- ***********************************************************************/
-
-#define CONFIG_SYS_ISA_MEM_BASE_ADDRESS 0x78000000
-/*
- Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu.
- Das funktioniert bei deren Karten, weil sie eine PCI-Bridge benutzen, die
- das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen
- auf ISA- und PCI-Zyklen)
- */
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
-/*#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0x79000000 */
-
-/************************************************************
- * Video support
- ************************************************************/
-
-#ifdef USE_VGA_GRAPHICS
-#define CONFIG_VIDEO /* To enable video controller support */
-#define CONFIG_VIDEO_CT69000
-#define CONFIG_CFB_CONSOLE
-/* #define CONFIG_VIDEO_LOGO */
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-/* #define CONFIG_VIDEO_HW_CURSOR */
-#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
-
-#define VIDEO_HW_RECTFILL
-#define VIDEO_HW_BITBLT
-
-#endif
-
-/************************************************************
- * Ident
- ************************************************************/
-#define CONFIG_SC3_VERSION "r1.4"
-
-#define POST_OUT(x) (*((volatile unsigned char*)(0x79000080))=x)
-
-#endif /* __CONFIG_H */