* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (69 commits)
davinci: Initial support for Neuros OSD2 platform.
davinci: remove unused variable in arch/arm/mach-davinci/board-sffsdr.c
davinci: fix section mismatch warning in arch/arm/mach-davinci/board-dm646x-evm.c
DaVinci: DM365: Enable DaVinci RTC support for DM365 EVM
DA8xx/OMAP-L1xx: Add high speed SD/MMC capabilities
davinci: DA8XX/OMAP-L1XX: enable cpuidle and regulator in defconfig
davinci: DA850/OMAP-L138: avoid using separate initcall for initializing regulator
davinci: DA850/OMAP-L138 EVM: register for cpuidle support
davinci: DA8XX/OMAP-L1XX: add support for cpuidle driver register
davinci: add CPU idle driver
davinci: DA8XX/OMAP-L1XX: fix compiler warning
davinci: DA850/OMAP-L138: eliminate static function declaration
davinci: DA850/OMAP-L138 EVM: simplify configuration of emac in MII/RMII mode
davinci: DA850/OMAP-L138 EVM: get rid of DA850_UI_EXP config option
davinci: DA850/OMAP-L138 EVM: implement autodetect of RMII PHY
davinci: DA830/OMAP-L137 EVM: do not configure NAND on UI card when MMC/SD is selected
davinci: DA830/OMAP-L137 EVM: use runtime detection for UI card
davinci: DA830/OMAP-L137 EVM: remove ifdefs inside da830_evm_init()
davinci: DA830/OMAP-L137 EVM: fix warning with default config
davinci: Add NAND support for DA830/OMAP-L137 EVM platform
...
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc2-davinci1
-# Wed May 13 15:33:29 2009
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_POSIX_MQUEUE_SYSCTL=y
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_AUDIT is not set
-
-#
-# RCU Subsystem
-#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_GROUP_SCHED=y
-CONFIG_FAIR_GROUP_SCHED=y
-# CONFIG_RT_GROUP_SCHED is not set
-CONFIG_USER_SCHED=y
-# CONFIG_CGROUP_SCHED is not set
-# CONFIG_CGROUPS is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
-# CONFIG_RELAY is not set
-# CONFIG_NAMESPACES is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_RD_GZIP=y
-# CONFIG_RD_BZIP2 is not set
-# CONFIG_RD_LZMA is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL=y
-CONFIG_ANON_INODES=y
-CONFIG_EMBEDDED=y
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_AIO=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLUB_DEBUG=y
-CONFIG_COMPAT_BRK=y
-# CONFIG_SLAB is not set
-CONFIG_SLUB=y
-# CONFIG_SLOB is not set
-# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
-CONFIG_HAVE_OPROFILE=y
-# CONFIG_KPROBES is not set
-CONFIG_HAVE_KPROBES=y
-CONFIG_HAVE_KRETPROBES=y
-CONFIG_HAVE_CLK=y
-# CONFIG_SLOW_WORK is not set
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_SLABINFO=y
-CONFIG_RT_MUTEXES=y
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_FORCE_LOAD is not set
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_BLK_DEV_INTEGRITY is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_DEFAULT_AS=y
-# CONFIG_DEFAULT_DEADLINE is not set
-# CONFIG_DEFAULT_CFQ is not set
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="anticipatory"
-# CONFIG_FREEZER is not set
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_LOKI is not set
-# CONFIG_ARCH_MV78XX0 is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_ORION5X is not set
-# CONFIG_ARCH_PNX4008 is not set
-# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_S3C64XX is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-CONFIG_ARCH_DAVINCI=y
-# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
-CONFIG_CP_INTC=y
-
-#
-# TI DaVinci Implementations
-#
-
-#
-# DaVinci Core Type
-#
-# CONFIG_ARCH_DAVINCI_DM644x is not set
-# CONFIG_ARCH_DAVINCI_DM646x is not set
-# CONFIG_ARCH_DAVINCI_DM355 is not set
-CONFIG_ARCH_DAVINCI_DA830=y
-
-#
-# DaVinci Board Type
-#
-CONFIG_MACH_DAVINCI_DA830_EVM=y
-CONFIG_DAVINCI_MUX=y
-# CONFIG_DAVINCI_MUX_DEBUG is not set
-# CONFIG_DAVINCI_MUX_WARNINGS is not set
-CONFIG_DAVINCI_RESET_CLOCKS=y
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_ARM926T=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5TJ=y
-CONFIG_CPU_PABRT_NOIFAR=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-
-#
-# Processor Features
-#
-CONFIG_ARM_THUMB=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-CONFIG_CPU_DCACHE_WRITETHROUGH=y
-# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_COMMON_CLKDEV=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_VMSPLIT_3G=y
-# CONFIG_VMSPLIT_2G is not set
-# CONFIG_VMSPLIT_1G is not set
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_HIGHMEM is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_PHYS_ADDR_T_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
-CONFIG_HAVE_MLOCK=y
-CONFIG_HAVE_MLOCKED_PAGE_BIT=y
-CONFIG_LEDS=y
-# CONFIG_LEDS_CPU is not set
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE=""
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# CPU Power Management
-#
-# CONFIG_CPU_IDLE is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-# CONFIG_VFP is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_HAVE_AOUT=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_XFRM_STATISTICS is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-CONFIG_INET_TUNNEL=m
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-CONFIG_IPV6=m
-# CONFIG_IPV6_PRIVACY is not set
-# CONFIG_IPV6_ROUTER_PREF is not set
-# CONFIG_IPV6_OPTIMISTIC_DAD is not set
-# CONFIG_INET6_AH is not set
-# CONFIG_INET6_ESP is not set
-# CONFIG_INET6_IPCOMP is not set
-# CONFIG_IPV6_MIP6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-CONFIG_INET6_XFRM_MODE_TRANSPORT=m
-CONFIG_INET6_XFRM_MODE_TUNNEL=m
-CONFIG_INET6_XFRM_MODE_BEET=m
-# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
-CONFIG_IPV6_SIT=m
-CONFIG_IPV6_NDISC_NODETYPE=y
-# CONFIG_IPV6_TUNNEL is not set
-# CONFIG_IPV6_MULTIPLE_TABLES is not set
-# CONFIG_IPV6_MROUTE is not set
-# CONFIG_NETWORK_SECMARK is not set
-CONFIG_NETFILTER=y
-# CONFIG_NETFILTER_DEBUG is not set
-CONFIG_NETFILTER_ADVANCED=y
-
-#
-# Core Netfilter Configuration
-#
-# CONFIG_NETFILTER_NETLINK_QUEUE is not set
-# CONFIG_NETFILTER_NETLINK_LOG is not set
-# CONFIG_NF_CONNTRACK is not set
-# CONFIG_NETFILTER_XTABLES is not set
-# CONFIG_IP_VS is not set
-
-#
-# IP: Netfilter Configuration
-#
-# CONFIG_NF_DEFRAG_IPV4 is not set
-# CONFIG_IP_NF_QUEUE is not set
-# CONFIG_IP_NF_IPTABLES is not set
-# CONFIG_IP_NF_ARPTABLES is not set
-
-#
-# IPv6: Netfilter Configuration
-#
-# CONFIG_IP6_NF_QUEUE is not set
-# CONFIG_IP6_NF_IPTABLES is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_NET_DSA is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_PHONET is not set
-# CONFIG_NET_SCHED is not set
-# CONFIG_DCB is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_CAN is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-# CONFIG_WIRELESS is not set
-# CONFIG_WIMAX is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-CONFIG_BLK_DEV=y
-# CONFIG_BLK_DEV_COW_COMMON is not set
-CONFIG_BLK_DEV_LOOP=m
-# CONFIG_BLK_DEV_CRYPTOLOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=1
-CONFIG_BLK_DEV_RAM_SIZE=32768
-# CONFIG_BLK_DEV_XIP is not set
-# CONFIG_CDROM_PKTCDVD is not set
-# CONFIG_ATA_OVER_ETH is not set
-CONFIG_MISC_DEVICES=y
-# CONFIG_ICS932S401 is not set
-# CONFIG_ENCLOSURE_SERVICES is not set
-# CONFIG_ISL29003 is not set
-# CONFIG_C2PORT is not set
-
-#
-# EEPROM support
-#
-CONFIG_EEPROM_AT24=y
-# CONFIG_EEPROM_LEGACY is not set
-# CONFIG_EEPROM_93CX6 is not set
-CONFIG_HAVE_IDE=y
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-CONFIG_SCSI=m
-CONFIG_SCSI_DMA=y
-# CONFIG_SCSI_TGT is not set
-# CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
-
-#
-# SCSI support type (disk, tape, CD-ROM)
-#
-CONFIG_BLK_DEV_SD=m
-# CONFIG_CHR_DEV_ST is not set
-# CONFIG_CHR_DEV_OSST is not set
-# CONFIG_BLK_DEV_SR is not set
-# CONFIG_CHR_DEV_SG is not set
-# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
-# CONFIG_SCSI_MULTI_LUN is not set
-# CONFIG_SCSI_CONSTANTS is not set
-# CONFIG_SCSI_LOGGING is not set
-# CONFIG_SCSI_SCAN_ASYNC is not set
-CONFIG_SCSI_WAIT_SCAN=m
-
-#
-# SCSI Transports
-#
-# CONFIG_SCSI_SPI_ATTRS is not set
-# CONFIG_SCSI_FC_ATTRS is not set
-# CONFIG_SCSI_ISCSI_ATTRS is not set
-# CONFIG_SCSI_SAS_LIBSAS is not set
-# CONFIG_SCSI_SRP_ATTRS is not set
-CONFIG_SCSI_LOWLEVEL=y
-# CONFIG_ISCSI_TCP is not set
-# CONFIG_LIBFC is not set
-# CONFIG_LIBFCOE is not set
-# CONFIG_SCSI_DEBUG is not set
-# CONFIG_SCSI_DH is not set
-# CONFIG_SCSI_OSD_INITIATOR is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-CONFIG_TUN=m
-# CONFIG_VETH is not set
-CONFIG_PHYLIB=y
-
-#
-# MII PHY device drivers
-#
-# CONFIG_MARVELL_PHY is not set
-# CONFIG_DAVICOM_PHY is not set
-# CONFIG_QSEMI_PHY is not set
-CONFIG_LXT_PHY=y
-# CONFIG_CICADA_PHY is not set
-# CONFIG_VITESSE_PHY is not set
-# CONFIG_SMSC_PHY is not set
-# CONFIG_BROADCOM_PHY is not set
-# CONFIG_ICPLUS_PHY is not set
-# CONFIG_REALTEK_PHY is not set
-# CONFIG_NATIONAL_PHY is not set
-# CONFIG_STE10XP is not set
-CONFIG_LSI_ET1011C_PHY=y
-# CONFIG_FIXED_PHY is not set
-# CONFIG_MDIO_BITBANG is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-# CONFIG_SMC91X is not set
-CONFIG_TI_DAVINCI_EMAC=y
-# CONFIG_DM9000 is not set
-# CONFIG_ETHOC is not set
-# CONFIG_SMC911X is not set
-# CONFIG_SMSC911X is not set
-# CONFIG_DNET is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
-# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
-# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-
-#
-# Enable WiMAX (Networking options) to see the WiMAX drivers
-#
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-CONFIG_NETCONSOLE=y
-# CONFIG_NETCONSOLE_DYNAMIC is not set
-CONFIG_NETPOLL=y
-CONFIG_NETPOLL_TRAP=y
-CONFIG_NET_POLL_CONTROLLER=y
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=m
-CONFIG_INPUT_MOUSEDEV_PSAUX=y
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-
-#
-# Input Device Drivers
-#
-CONFIG_INPUT_KEYBOARD=y
-CONFIG_KEYBOARD_ATKBD=m
-# CONFIG_KEYBOARD_SUNKBD is not set
-# CONFIG_KEYBOARD_LKKBD is not set
-CONFIG_KEYBOARD_XTKBD=m
-# CONFIG_KEYBOARD_NEWTON is not set
-# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
-# CONFIG_TOUCHSCREEN_AD7879 is not set
-# CONFIG_TOUCHSCREEN_FUJITSU is not set
-# CONFIG_TOUCHSCREEN_GUNZE is not set
-# CONFIG_TOUCHSCREEN_ELO is not set
-# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
-# CONFIG_TOUCHSCREEN_MTOUCH is not set
-# CONFIG_TOUCHSCREEN_INEXIO is not set
-# CONFIG_TOUCHSCREEN_MK712 is not set
-# CONFIG_TOUCHSCREEN_PENMOUNT is not set
-# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
-# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
-# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
-# CONFIG_TOUCHSCREEN_TSC2007 is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-CONFIG_SERIO=y
-CONFIG_SERIO_SERPORT=y
-CONFIG_SERIO_LIBPS2=y
-# CONFIG_SERIO_RAW is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-# CONFIG_VT_CONSOLE is not set
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-CONFIG_DEVKMEM=y
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=3
-CONFIG_SERIAL_8250_RUNTIME_UARTS=3
-# CONFIG_SERIAL_8250_EXTENDED is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-# CONFIG_IPMI_HANDLER is not set
-CONFIG_HW_RANDOM=m
-# CONFIG_HW_RANDOM_TIMERIOMEM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_HELPER_AUTO=y
-
-#
-# I2C Hardware Bus support
-#
-
-#
-# I2C system bus drivers (mostly embedded / system-on-chip)
-#
-CONFIG_I2C_DAVINCI=y
-# CONFIG_I2C_GPIO is not set
-# CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_SIMTEC is not set
-
-#
-# External I2C/SMBus adapter drivers
-#
-# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_TAOS_EVM is not set
-
-#
-# Other I2C/SMBus bus drivers
-#
-# CONFIG_I2C_PCA_PLATFORM is not set
-# CONFIG_I2C_STUB is not set
-
-#
-# Miscellaneous I2C Chip support
-#
-# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
-# CONFIG_SENSORS_TSL2550 is not set
-# CONFIG_I2C_DEBUG_CORE is not set
-# CONFIG_I2C_DEBUG_ALGO is not set
-# CONFIG_I2C_DEBUG_BUS is not set
-# CONFIG_I2C_DEBUG_CHIP is not set
-# CONFIG_SPI is not set
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-CONFIG_GPIOLIB=y
-# CONFIG_DEBUG_GPIO is not set
-# CONFIG_GPIO_SYSFS is not set
-
-#
-# Memory mapped GPIO expanders:
-#
-
-#
-# I2C GPIO expanders:
-#
-# CONFIG_GPIO_MAX732X is not set
-# CONFIG_GPIO_PCA953X is not set
-CONFIG_GPIO_PCF857X=m
-
-#
-# PCI GPIO expanders:
-#
-
-#
-# SPI GPIO expanders:
-#
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
-CONFIG_WATCHDOG=y
-# CONFIG_WATCHDOG_NOWAYOUT is not set
-
-#
-# Watchdog Device Drivers
-#
-# CONFIG_SOFT_WATCHDOG is not set
-# CONFIG_DAVINCI_WATCHDOG is not set
-CONFIG_SSB_POSSIBLE=y
-
-#
-# Sonics Silicon Backplane
-#
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_CORE is not set
-# CONFIG_MFD_SM501 is not set
-# CONFIG_MFD_ASIC3 is not set
-# CONFIG_HTC_EGPIO is not set
-# CONFIG_HTC_PASIC3 is not set
-# CONFIG_TPS65010 is not set
-# CONFIG_TWL4030_CORE is not set
-# CONFIG_MFD_TMIO is not set
-# CONFIG_MFD_T7L66XB is not set
-# CONFIG_MFD_TC6387XB is not set
-# CONFIG_MFD_TC6393XB is not set
-# CONFIG_PMIC_DA903X is not set
-# CONFIG_MFD_WM8400 is not set
-# CONFIG_MFD_WM8350_I2C is not set
-# CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_SOUND=m
-# CONFIG_SOUND_OSS_CORE is not set
-CONFIG_SND=m
-CONFIG_SND_TIMER=m
-CONFIG_SND_PCM=m
-CONFIG_SND_JACK=y
-# CONFIG_SND_SEQUENCER is not set
-# CONFIG_SND_MIXER_OSS is not set
-# CONFIG_SND_PCM_OSS is not set
-# CONFIG_SND_HRTIMER is not set
-# CONFIG_SND_DYNAMIC_MINORS is not set
-CONFIG_SND_SUPPORT_OLD_API=y
-CONFIG_SND_VERBOSE_PROCFS=y
-# CONFIG_SND_VERBOSE_PRINTK is not set
-# CONFIG_SND_DEBUG is not set
-CONFIG_SND_DRIVERS=y
-# CONFIG_SND_DUMMY is not set
-# CONFIG_SND_MTPAV is not set
-# CONFIG_SND_SERIAL_U16550 is not set
-# CONFIG_SND_MPU401 is not set
-CONFIG_SND_ARM=y
-CONFIG_SND_SOC=m
-CONFIG_SND_DAVINCI_SOC=m
-CONFIG_SND_SOC_I2C_AND_SPI=m
-# CONFIG_SND_SOC_ALL_CODECS is not set
-# CONFIG_SOUND_PRIME is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_USB_MUSB_HOST is not set
-# CONFIG_USB_MUSB_PERIPHERAL is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-# CONFIG_USB_GADGET_AT91 is not set
-# CONFIG_USB_GADGET_ATMEL_USBA is not set
-# CONFIG_USB_GADGET_FSL_USB2 is not set
-# CONFIG_USB_GADGET_LH7A40X is not set
-# CONFIG_USB_GADGET_OMAP is not set
-# CONFIG_USB_GADGET_PXA25X is not set
-# CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
-# CONFIG_USB_GADGET_IMX is not set
-# CONFIG_USB_GADGET_M66592 is not set
-# CONFIG_USB_GADGET_AMD5536UDC is not set
-# CONFIG_USB_GADGET_FSL_QE is not set
-# CONFIG_USB_GADGET_CI13XXX is not set
-# CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_GOKU is not set
-# CONFIG_USB_GADGET_DUMMY_HCD is not set
-# CONFIG_USB_ZERO is not set
-# CONFIG_USB_ETH is not set
-# CONFIG_USB_GADGETFS is not set
-# CONFIG_USB_FILE_STORAGE is not set
-# CONFIG_USB_G_SERIAL is not set
-# CONFIG_USB_MIDI_GADGET is not set
-# CONFIG_USB_G_PRINTER is not set
-# CONFIG_USB_CDC_COMPOSITE is not set
-# CONFIG_MMC is not set
-# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-# CONFIG_DMADEVICES is not set
-# CONFIG_AUXDISPLAY is not set
-# CONFIG_REGULATOR is not set
-# CONFIG_UIO is not set
-# CONFIG_STAGING is not set
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT2_FS_XIP is not set
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-CONFIG_EXT3_FS_XATTR=y
-# CONFIG_EXT3_FS_POSIX_ACL is not set
-# CONFIG_EXT3_FS_SECURITY is not set
-# CONFIG_EXT4_FS is not set
-CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
-CONFIG_FS_MBCACHE=y
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-# CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
-CONFIG_XFS_FS=m
-# CONFIG_XFS_QUOTA is not set
-# CONFIG_XFS_POSIX_ACL is not set
-# CONFIG_XFS_RT is not set
-# CONFIG_XFS_DEBUG is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_BTRFS_FS is not set
-CONFIG_DNOTIFY=y
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-# CONFIG_QUOTA is not set
-# CONFIG_AUTOFS_FS is not set
-CONFIG_AUTOFS4_FS=m
-# CONFIG_FUSE_FS is not set
-
-#
-# Caches
-#
-# CONFIG_FSCACHE is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-CONFIG_FAT_FS=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_FAT_DEFAULT_CODEPAGE=437
-CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_PROC_PAGE_MONITOR=y
-CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-CONFIG_MISC_FILESYSTEMS=y
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-CONFIG_CRAMFS=y
-# CONFIG_SQUASHFS is not set
-# CONFIG_VXFS_FS is not set
-CONFIG_MINIX_FS=m
-# CONFIG_OMFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-# CONFIG_NFS_V3_ACL is not set
-# CONFIG_NFS_V4 is not set
-CONFIG_ROOT_NFS=y
-CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
-# CONFIG_NFSD_V3_ACL is not set
-# CONFIG_NFSD_V4 is not set
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_EXPORTFS=m
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-CONFIG_SMB_FS=m
-# CONFIG_SMB_NLS_DEFAULT is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_ACORN_PARTITION is not set
-# CONFIG_OSF_PARTITION is not set
-# CONFIG_AMIGA_PARTITION is not set
-# CONFIG_ATARI_PARTITION is not set
-# CONFIG_MAC_PARTITION is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_BSD_DISKLABEL is not set
-# CONFIG_MINIX_SUBPARTITION is not set
-# CONFIG_SOLARIS_X86_PARTITION is not set
-# CONFIG_UNIXWARE_DISKLABEL is not set
-# CONFIG_LDM_PARTITION is not set
-# CONFIG_SGI_PARTITION is not set
-# CONFIG_ULTRIX_PARTITION is not set
-# CONFIG_SUN_PARTITION is not set
-# CONFIG_KARMA_PARTITION is not set
-# CONFIG_EFI_PARTITION is not set
-# CONFIG_SYSV68_PARTITION is not set
-CONFIG_NLS=y
-CONFIG_NLS_DEFAULT="iso8859-1"
-CONFIG_NLS_CODEPAGE_437=y
-# CONFIG_NLS_CODEPAGE_737 is not set
-# CONFIG_NLS_CODEPAGE_775 is not set
-# CONFIG_NLS_CODEPAGE_850 is not set
-# CONFIG_NLS_CODEPAGE_852 is not set
-# CONFIG_NLS_CODEPAGE_855 is not set
-# CONFIG_NLS_CODEPAGE_857 is not set
-# CONFIG_NLS_CODEPAGE_860 is not set
-# CONFIG_NLS_CODEPAGE_861 is not set
-# CONFIG_NLS_CODEPAGE_862 is not set
-# CONFIG_NLS_CODEPAGE_863 is not set
-# CONFIG_NLS_CODEPAGE_864 is not set
-# CONFIG_NLS_CODEPAGE_865 is not set
-# CONFIG_NLS_CODEPAGE_866 is not set
-# CONFIG_NLS_CODEPAGE_869 is not set
-# CONFIG_NLS_CODEPAGE_936 is not set
-# CONFIG_NLS_CODEPAGE_950 is not set
-# CONFIG_NLS_CODEPAGE_932 is not set
-# CONFIG_NLS_CODEPAGE_949 is not set
-# CONFIG_NLS_CODEPAGE_874 is not set
-# CONFIG_NLS_ISO8859_8 is not set
-# CONFIG_NLS_CODEPAGE_1250 is not set
-# CONFIG_NLS_CODEPAGE_1251 is not set
-CONFIG_NLS_ASCII=m
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_NLS_ISO8859_2 is not set
-# CONFIG_NLS_ISO8859_3 is not set
-# CONFIG_NLS_ISO8859_4 is not set
-# CONFIG_NLS_ISO8859_5 is not set
-# CONFIG_NLS_ISO8859_6 is not set
-# CONFIG_NLS_ISO8859_7 is not set
-# CONFIG_NLS_ISO8859_9 is not set
-# CONFIG_NLS_ISO8859_13 is not set
-# CONFIG_NLS_ISO8859_14 is not set
-# CONFIG_NLS_ISO8859_15 is not set
-# CONFIG_NLS_KOI8_R is not set
-# CONFIG_NLS_KOI8_U is not set
-CONFIG_NLS_UTF8=m
-# CONFIG_DLM is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_FRAME_WARN=1024
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-CONFIG_DEBUG_FS=y
-# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
-CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
-CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
-CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-CONFIG_TIMER_STATS=y
-# CONFIG_DEBUG_OBJECTS is not set
-# CONFIG_SLUB_DEBUG_ON is not set
-# CONFIG_SLUB_STATS is not set
-CONFIG_DEBUG_PREEMPT=y
-CONFIG_DEBUG_RT_MUTEXES=y
-CONFIG_DEBUG_PI_LIST=y
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_WRITECOUNT is not set
-# CONFIG_DEBUG_MEMORY_INIT is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-# CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-# CONFIG_BACKTRACE_SELF_TEST is not set
-# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
-# CONFIG_FAULT_INJECTION is not set
-# CONFIG_LATENCYTOP is not set
-# CONFIG_SYSCTL_SYSCALL_CHECK is not set
-# CONFIG_PAGE_POISONING is not set
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_DYNAMIC_DEBUG is not set
-# CONFIG_SAMPLES is not set
-CONFIG_HAVE_ARCH_KGDB=y
-# CONFIG_KGDB is not set
-CONFIG_ARM_UNWIND=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_DEBUG_LL is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITYFS is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-
-#
-# Crypto core or helper
-#
-# CONFIG_CRYPTO_FIPS is not set
-# CONFIG_CRYPTO_MANAGER is not set
-# CONFIG_CRYPTO_MANAGER2 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-# CONFIG_CRYPTO_TEST is not set
-
-#
-# Authenticated Encryption with Associated Data
-#
-# CONFIG_CRYPTO_CCM is not set
-# CONFIG_CRYPTO_GCM is not set
-# CONFIG_CRYPTO_SEQIV is not set
-
-#
-# Block modes
-#
-# CONFIG_CRYPTO_CBC is not set
-# CONFIG_CRYPTO_CTR is not set
-# CONFIG_CRYPTO_CTS is not set
-# CONFIG_CRYPTO_ECB is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_XTS is not set
-
-#
-# Hash modes
-#
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-
-#
-# Digest
-#
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_MD4 is not set
-# CONFIG_CRYPTO_MD5 is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_RMD128 is not set
-# CONFIG_CRYPTO_RMD160 is not set
-# CONFIG_CRYPTO_RMD256 is not set
-# CONFIG_CRYPTO_RMD320 is not set
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_WP512 is not set
-
-#
-# Ciphers
-#
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_DES is not set
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_SALSA20 is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-
-#
-# Compression
-#
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_ZLIB is not set
-# CONFIG_CRYPTO_LZO is not set
-
-#
-# Random Number Generation
-#
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
-# CONFIG_BINARY_PRINTF is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-CONFIG_GENERIC_FIND_LAST_BIT=y
-CONFIG_CRC_CCITT=m
-# CONFIG_CRC16 is not set
-CONFIG_CRC_T10DIF=m
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_ZLIB_INFLATE=y
-CONFIG_DECOMPRESS_GZIP=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
-CONFIG_NLATTR=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-davinci1
-# Mon Jun 29 07:54:15 2009
+# Linux kernel version: 2.6.32-rc5
+# Thu Oct 22 12:19:19 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_HAS_CPUFREQ=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_USER_SCHED=y
# CONFIG_CGROUP_SCHED is not set
# CONFIG_CGROUPS is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
# CONFIG_NAMESPACES is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
CONFIG_COMPAT_BRK=y
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
#
# System Type
#
+CONFIG_MMU=y
# CONFIG_ARCH_AAEC2000 is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
# CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
-# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
CONFIG_ARCH_DAVINCI=y
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_BCMRING is not set
CONFIG_CP_INTC=y
#
# CONFIG_ARCH_DAVINCI_DM644x is not set
# CONFIG_ARCH_DAVINCI_DM355 is not set
# CONFIG_ARCH_DAVINCI_DM646x is not set
-# CONFIG_ARCH_DAVINCI_DA830 is not set
+CONFIG_ARCH_DAVINCI_DA830=y
CONFIG_ARCH_DAVINCI_DA850=y
CONFIG_ARCH_DAVINCI_DA8XX=y
# CONFIG_ARCH_DAVINCI_DM365 is not set
#
# DaVinci Board Type
#
+CONFIG_MACH_DAVINCI_DA830_EVM=y
+CONFIG_DA830_UI=y
+CONFIG_DA830_UI_LCD=y
+# CONFIG_DA830_UI_NAND is not set
CONFIG_MACH_DAVINCI_DA850_EVM=y
+CONFIG_DA850_UI_EXP=y
+CONFIG_DA850_UI_NONE=y
+# CONFIG_DA850_UI_RMII is not set
CONFIG_DAVINCI_MUX=y
# CONFIG_DAVINCI_MUX_DEBUG is not set
# CONFIG_DAVINCI_MUX_WARNINGS is not set
CONFIG_CPU_ARM926T=y
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5TJ=y
-CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_PABRT_LEGACY=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y
CONFIG_ARM_THUMB=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+CONFIG_CPU_DCACHE_WRITETHROUGH=y
# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-# CONFIG_OUTER_CACHE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
CONFIG_COMMON_CLKDEV=y
#
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
-# CONFIG_ARCH_HAS_HOLES_MEMORYMODEL is not set
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_HIGHMEM is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_LEDS=y
# CONFIG_LEDS_CPU is not set
CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
#
# Boot options
#
# CPU Power Management
#
-# CONFIG_CPU_IDLE is not set
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+# CONFIG_CPU_FREQ_DEBUG is not set
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=m
+CONFIG_CPU_FREQ_GOV_POWERSAVE=m
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=m
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_IDLE_GOV_MENU=y
#
# Floating point emulation
# CONFIG_IP6_NF_IPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
CONFIG_MISC_DEVICES=y
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
#
CONFIG_EEPROM_AT24=y
# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
CONFIG_MII=y
# CONFIG_AX88796 is not set
# CONFIG_SMC91X is not set
-# CONFIG_TI_DAVINCI_EMAC is not set
+CONFIG_TI_DAVINCI_EMAC=y
# CONFIG_DM9000 is not set
# CONFIG_ETHOC is not set
# CONFIG_SMC911X is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851_MLL is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
#
# Input device support
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=m
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-CONFIG_KEYBOARD_XTKBD=m
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+CONFIG_KEYBOARD_XTKBD=m
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
# CONFIG_TOUCHSCREEN_FUJITSU is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
# CONFIG_INPUT_MISC is not set
#
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
# I2C system bus drivers (mostly embedded / system-on-chip)
#
CONFIG_I2C_DAVINCI=y
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
# I2C GPIO expanders:
#
# CONFIG_GPIO_MAX732X is not set
-# CONFIG_GPIO_PCA953X is not set
-CONFIG_GPIO_PCF857X=m
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCF857X=y
#
# PCI GPIO expanders:
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_AB3100_CORE is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+CONFIG_REGULATOR_TPS6507X=y
+# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_DAVINCI is not set
+# CONFIG_FB_VIRTUAL is not set
+CONFIG_FB_DA8XX=y
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_SOUND=m
# CONFIG_SOUND_OSS_CORE is not set
CONFIG_SND=m
CONFIG_SND_VERBOSE_PROCFS=y
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
CONFIG_SND_DRIVERS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
CONFIG_SND_ARM=y
CONFIG_SND_SOC=m
CONFIG_SND_DAVINCI_SOC=m
+# CONFIG_SND_DA830_SOC_EVM is not set
+# CONFIG_SND_DA850_SOC_EVM is not set
CONFIG_SND_SOC_I2C_AND_SPI=m
# CONFIG_SND_SOC_ALL_CODECS is not set
# CONFIG_SOUND_PRIME is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
-# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
# CONFIG_STAGING is not set
#
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
CONFIG_XFS_FS=m
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_POSIX_ACL is not set
# CONFIG_XFS_RT is not set
# CONFIG_XFS_DEBUG is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
CONFIG_DEBUG_RT_MUTEXES=y
CONFIG_DEBUG_PI_LIST=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_KMEMTRACE is not set
# CONFIG_WORKQUEUE_TRACER is not set
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc3-davinci1
-# Fri Jul 17 08:26:52 2009
+# Linux kernel version: 2.6.32-rc4
+# Mon Oct 12 14:13:12 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_AIO=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_KPROBES=y
#
# System Type
#
+CONFIG_MMU=y
# CONFIG_ARCH_AAEC2000 is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
# CONFIG_ARCH_U300 is not set
CONFIG_ARCH_DAVINCI=y
# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_BCMRING is not set
CONFIG_AINTC=y
CONFIG_ARCH_DAVINCI_DMx=y
#
CONFIG_MACH_DAVINCI_EVM=y
CONFIG_MACH_SFFSDR=y
+CONFIG_MACH_NEUROS_OSD2=y
CONFIG_MACH_DAVINCI_DM355_EVM=y
CONFIG_MACH_DM355_LEOPARD=y
CONFIG_MACH_DAVINCI_DM6467_EVM=y
CONFIG_CPU_ARM926T=y
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5TJ=y
-CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_PABRT_LEGACY=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
CONFIG_COMMON_CLKDEV=y
#
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
CONFIG_VIRT_TO_BUS=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_LEDS=y
# CONFIG_LEDS_CPU is not set
# CONFIG_IP6_NF_IPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=m
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_AFS_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=m
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
+# CONFIG_KS8851_MLL is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_NETPOLL_TRAP=y
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
#
# Input device support
#
# Userland interfaces
#
-CONFIG_INPUT_MOUSEDEV=m
-CONFIG_INPUT_MOUSEDEV_PSAUX=y
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=m
CONFIG_INPUT_EVBUG=m
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=m
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
CONFIG_KEYBOARD_GPIO=y
# CONFIG_KEYBOARD_MATRIX is not set
# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
CONFIG_KEYBOARD_XTKBD=m
# CONFIG_TOUCHSCREEN_GUNZE is not set
# CONFIG_TOUCHSCREEN_ELO is not set
# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
# CONFIG_TOUCHSCREEN_MTOUCH is not set
# CONFIG_TOUCHSCREEN_INEXIO is not set
# CONFIG_TOUCHSCREEN_MK712 is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
# CONFIG_TOUCHSCREEN_TSC2007 is not set
# CONFIG_TOUCHSCREEN_W90X900 is not set
-# CONFIG_INPUT_MISC is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_CM109 is not set
+# CONFIG_INPUT_UINPUT is not set
+# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
+CONFIG_INPUT_DM355EVM=m
+CONFIG_INPUT_DM365EVM=m
#
# Hardware I/O ports
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-CONFIG_HW_RANDOM=m
-# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
#
# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCA953X is not set
-CONFIG_GPIO_PCF857X=m
+CONFIG_GPIO_PCF857X=y
#
# PCI GPIO expanders:
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_ASIC3 is not set
-# CONFIG_MFD_DM355EVM_MSP is not set
+CONFIG_MFD_DM355EVM_MSP=y
# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_TPS65010 is not set
# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
+# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB_DDC is not set
# CONFIG_FB_BOOT_VESA_SUPPORT is not set
-# CONFIG_FB_CFB_FILLRECT is not set
-# CONFIG_FB_CFB_COPYAREA is not set
-# CONFIG_FB_CFB_IMAGEBLIT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# Frame buffer hardware drivers
#
# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_DAVINCI=y
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=m
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=m
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=m
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=m
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HWA_HCD is not set
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
# CONFIG_USB_GADGET_PXA27X is not set
# CONFIG_USB_GADGET_S3C_HSOTG is not set
# CONFIG_USB_GADGET_IMX is not set
# CONFIG_USB_AUDIO is not set
CONFIG_USB_ETH=m
CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
CONFIG_USB_GADGETFS=m
CONFIG_USB_FILE_STORAGE=m
# CONFIG_USB_FILE_STORAGE_TEST is not set
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+CONFIG_MMC_DAVINCI=m
# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m
#
# iptables trigger is under Netfilter config (LED target)
#
+# CONFIG_ACCESSIBILITY is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=m
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_DM355EVM is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
#
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
-# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
# CONFIG_STAGING is not set
#
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
-CONFIG_ARM_UNWIND=y
+# CONFIG_ARM_UNWIND is not set
CONFIG_DEBUG_USER=y
CONFIG_DEBUG_ERRORS=y
# CONFIG_DEBUG_STACK_USAGE is not set
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
bool "DA830/OMAP-L137 based system"
select CP_INTC
select ARCH_DAVINCI_DA8XX
+ select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1
config ARCH_DAVINCI_DA850
bool "DA850/OMAP-L138 based system"
select CP_INTC
select ARCH_DAVINCI_DA8XX
+ select ARCH_HAS_CPUFREQ
config ARCH_DAVINCI_DA8XX
bool
Say Y here to select the Lyrtech Small Form Factor
Software Defined Radio (SFFSDR) board.
+config MACH_NEUROS_OSD2
+ bool "Neuros OSD2 Open Television Set Top Box"
+ depends on ARCH_DAVINCI_DM644x
+ help
+ Configure this option to specify the whether the board used
+ for development is a Neuros OSD2 Open Set Top Box.
+
config MACH_DAVINCI_DM355_EVM
bool "TI DM355 EVM"
default ARCH_DAVINCI_DM355
bool "TI DA830/OMAP-L137 Reference Platform"
default ARCH_DAVINCI_DA830
depends on ARCH_DAVINCI_DA830
+ select GPIO_PCF857X
help
Say Y here to select the TI DA830/OMAP-L137 Evaluation Module.
+choice
+ prompt "Select DA830/OMAP-L137 UI board peripheral"
+ depends on MACH_DAVINCI_DA830_EVM
+ help
+ The presence of UI card on the DA830/OMAP-L137 EVM is detected
+ automatically based on successful probe of the I2C based GPIO
+ expander on that board. This option selected in this menu has
+ an effect only in case of a successful UI card detection.
+
+config DA830_UI_LCD
+ bool "LCD"
+ help
+ Say Y here to use the LCD as a framebuffer or simple character
+ display.
+
+config DA830_UI_NAND
+ bool "NAND flash"
+ help
+ Say Y here to use the NAND flash. Do not forget to setup
+ the switch correctly.
+endchoice
+
config MACH_DAVINCI_DA850_EVM
bool "TI DA850/OMAP-L138 Reference Platform"
default ARCH_DAVINCI_DA850
depends on ARCH_DAVINCI_DA850
+ select GPIO_PCA953X
help
Say Y here to select the TI DA850/OMAP-L138 Evaluation Module.
+choice
+ prompt "Select peripherals connected to expander on UI board"
+ depends on MACH_DAVINCI_DA850_EVM
+ help
+ The presence of User Interface (UI) card on the DA850/OMAP-L138
+ EVM is detected automatically based on successful probe of the I2C
+ based GPIO expander on that card. This option selected in this
+ menu has an effect only in case of a successful UI card detection.
+
+config DA850_UI_NONE
+ bool "No peripheral is enabled"
+ help
+ Say Y if you do not want to enable any of the peripherals connected
+ to TCA6416 expander on DA850/OMAP-L138 EVM UI card
+
+config DA850_UI_RMII
+ bool "RMII Ethernet PHY"
+ help
+ Say Y if you want to use the RMII PHY on the DA850/OMAP-L138 EVM.
+ This PHY is found on the UI daughter card that is supplied with
+ the EVM.
+ NOTE: Please take care while choosing this option, MII PHY will
+ not be functional if RMII mode is selected.
+
+endchoice
+
config DAVINCI_MUX
bool "DAVINCI multiplexing support"
depends on ARCH_DAVINCI
# Board specific
obj-$(CONFIG_MACH_DAVINCI_EVM) += board-dm644x-evm.o
obj-$(CONFIG_MACH_SFFSDR) += board-sffsdr.o
+obj-$(CONFIG_MACH_NEUROS_OSD2) += board-neuros-osd2.o
obj-$(CONFIG_MACH_DAVINCI_DM355_EVM) += board-dm355-evm.o
obj-$(CONFIG_MACH_DM355_LEOPARD) += board-dm355-leopard.o
obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM) += board-dm646x-evm.o
obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o
obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o
obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o
+
+# Power Management
+obj-$(CONFIG_CPU_FREQ) += cpufreq.o
+obj-$(CONFIG_CPU_IDLE) += cpuidle.o
* or implied.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
#include <linux/console.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
#include <linux/i2c.h>
+#include <linux/i2c/pcf857x.h>
#include <linux/i2c/at24.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <mach/common.h>
-#include <mach/irqs.h>
#include <mach/cp_intc.h>
+#include <mach/mux.h>
+#include <mach/nand.h>
#include <mach/da8xx.h>
-#include <mach/asp.h>
+#include <mach/usb.h>
#define DA830_EVM_PHY_MASK 0x0
#define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
-static struct at24_platform_data da830_evm_i2c_eeprom_info = {
- .byte_len = SZ_256K / 8,
- .page_size = 64,
- .flags = AT24_FLAG_ADDR16,
- .setup = davinci_get_mac_addr,
- .context = (void *)0x7f00,
-};
+#define DA830_EMIF25_ASYNC_DATA_CE3_BASE 0x62000000
+#define DA830_EMIF25_CONTROL_BASE 0x68000000
-static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c256", 0x50),
- .platform_data = &da830_evm_i2c_eeprom_info,
- },
- {
- I2C_BOARD_INFO("tlv320aic3x", 0x18),
- }
+/*
+ * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
+ */
+#define ON_BD_USB_DRV GPIO_TO_PIN(1, 15)
+#define ON_BD_USB_OVC GPIO_TO_PIN(2, 4)
+
+static const short da830_evm_usb11_pins[] = {
+ DA830_GPIO1_15, DA830_GPIO2_4,
+ -1
};
-static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
- .bus_freq = 100, /* kHz */
- .bus_delay = 0, /* usec */
+static da8xx_ocic_handler_t da830_evm_usb_ocic_handler;
+
+static int da830_evm_usb_set_power(unsigned port, int on)
+{
+ gpio_set_value(ON_BD_USB_DRV, on);
+ return 0;
+}
+
+static int da830_evm_usb_get_power(unsigned port)
+{
+ return gpio_get_value(ON_BD_USB_DRV);
+}
+
+static int da830_evm_usb_get_oci(unsigned port)
+{
+ return !gpio_get_value(ON_BD_USB_OVC);
+}
+
+static irqreturn_t da830_evm_usb_ocic_irq(int, void *);
+
+static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler)
+{
+ int irq = gpio_to_irq(ON_BD_USB_OVC);
+ int error = 0;
+
+ if (handler != NULL) {
+ da830_evm_usb_ocic_handler = handler;
+
+ error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED |
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "OHCI over-current indicator", NULL);
+ if (error)
+ printk(KERN_ERR "%s: could not request IRQ to watch "
+ "over-current indicator changes\n", __func__);
+ } else
+ free_irq(irq, NULL);
+
+ return error;
+}
+
+static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = {
+ .set_power = da830_evm_usb_set_power,
+ .get_power = da830_evm_usb_get_power,
+ .get_oci = da830_evm_usb_get_oci,
+ .ocic_notify = da830_evm_usb_ocic_notify,
+
+ /* TPS2065 switch @ 5V */
+ .potpgt = (3 + 1) / 2, /* 3 ms max */
};
+static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
+{
+ da830_evm_usb_ocic_handler(&da830_evm_usb11_pdata, 1);
+ return IRQ_HANDLED;
+}
+
+static __init void da830_evm_usb_init(void)
+{
+ u32 cfgchip2;
+ int ret;
+
+ /*
+ * Set up USB clock/mode in the CFGCHIP2 register.
+ * FYI: CFGCHIP2 is 0x0000ef00 initially.
+ */
+ cfgchip2 = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG));
+
+ /* USB2.0 PHY reference clock is 24 MHz */
+ cfgchip2 &= ~CFGCHIP2_REFFREQ;
+ cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ;
+
+ /*
+ * Select internal reference clock for USB 2.0 PHY
+ * and use it as a clock source for USB 1.1 PHY
+ * (this is the default setting anyway).
+ */
+ cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
+ cfgchip2 |= CFGCHIP2_USB2PHYCLKMUX;
+
+ /*
+ * We have to override VBUS/ID signals when MUSB is configured into the
+ * host-only mode -- ID pin will float if no cable is connected, so the
+ * controller won't be able to drive VBUS thinking that it's a B-device.
+ * Otherwise, we want to use the OTG mode and enable VBUS comparators.
+ */
+ cfgchip2 &= ~CFGCHIP2_OTGMODE;
+#ifdef CONFIG_USB_MUSB_HOST
+ cfgchip2 |= CFGCHIP2_FORCE_HOST;
+#else
+ cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
+#endif
+
+ __raw_writel(cfgchip2, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG));
+
+ /* USB_REFCLKIN is not used. */
+ ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
+ if (ret)
+ pr_warning("%s: USB 2.0 PinMux setup failed: %d\n",
+ __func__, ret);
+ else {
+ /*
+ * TPS2065 switch @ 5V supplies 1 A (sustains 1.5 A),
+ * with the power on to power good time of 3 ms.
+ */
+ ret = da8xx_register_usb20(1000, 3);
+ if (ret)
+ pr_warning("%s: USB 2.0 registration failed: %d\n",
+ __func__, ret);
+ }
+
+ ret = da8xx_pinmux_setup(da830_evm_usb11_pins);
+ if (ret) {
+ pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
+ __func__, ret);
+ return;
+ }
+
+ ret = gpio_request(ON_BD_USB_DRV, "ON_BD_USB_DRV");
+ if (ret) {
+ printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
+ "power control: %d\n", __func__, ret);
+ return;
+ }
+ gpio_direction_output(ON_BD_USB_DRV, 0);
+
+ ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC");
+ if (ret) {
+ printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
+ "over-current indicator: %d\n", __func__, ret);
+ return;
+ }
+ gpio_direction_input(ON_BD_USB_OVC);
+
+ ret = da8xx_register_usb11(&da830_evm_usb11_pdata);
+ if (ret)
+ pr_warning("%s: USB 1.1 registration failed: %d\n",
+ __func__, ret);
+}
+
static struct davinci_uart_config da830_evm_uart_config __initdata = {
.enabled_uarts = 0x7,
};
+static const short da830_evm_mcasp1_pins[] = {
+ DA830_AHCLKX1, DA830_ACLKX1, DA830_AFSX1, DA830_AHCLKR1, DA830_AFSR1,
+ DA830_AMUTE1, DA830_AXR1_0, DA830_AXR1_1, DA830_AXR1_2, DA830_AXR1_5,
+ DA830_ACLKR1, DA830_AXR1_6, DA830_AXR1_7, DA830_AXR1_8, DA830_AXR1_10,
+ DA830_AXR1_11,
+ -1
+};
+
static u8 da830_iis_serializer_direction[] = {
RX_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
INACTIVE_MODE, TX_MODE, INACTIVE_MODE, INACTIVE_MODE,
.rxnumevt = 1,
};
+/*
+ * GPIO2[1] is used as MMC_SD_WP and GPIO2[2] as MMC_SD_INS.
+ */
+static const short da830_evm_mmc_sd_pins[] = {
+ DA830_MMCSD_DAT_0, DA830_MMCSD_DAT_1, DA830_MMCSD_DAT_2,
+ DA830_MMCSD_DAT_3, DA830_MMCSD_DAT_4, DA830_MMCSD_DAT_5,
+ DA830_MMCSD_DAT_6, DA830_MMCSD_DAT_7, DA830_MMCSD_CLK,
+ DA830_MMCSD_CMD, DA830_GPIO2_1, DA830_GPIO2_2,
+ -1
+};
+
+#define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1)
+
+static int da830_evm_mmc_get_ro(int index)
+{
+ return gpio_get_value(DA830_MMCSD_WP_PIN);
+}
+
+static struct davinci_mmc_config da830_evm_mmc_config = {
+ .get_ro = da830_evm_mmc_get_ro,
+ .wires = 4,
+ .max_freq = 50000000,
+ .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
+ .version = MMC_CTLR_VERSION_2,
+};
+
+static inline void da830_evm_init_mmc(void)
+{
+ int ret;
+
+ ret = da8xx_pinmux_setup(da830_evm_mmc_sd_pins);
+ if (ret) {
+ pr_warning("da830_evm_init: mmc/sd mux setup failed: %d\n",
+ ret);
+ return;
+ }
+
+ ret = gpio_request(DA830_MMCSD_WP_PIN, "MMC WP");
+ if (ret) {
+ pr_warning("da830_evm_init: can not open GPIO %d\n",
+ DA830_MMCSD_WP_PIN);
+ return;
+ }
+ gpio_direction_input(DA830_MMCSD_WP_PIN);
+
+ ret = da8xx_register_mmcsd0(&da830_evm_mmc_config);
+ if (ret) {
+ pr_warning("da830_evm_init: mmc/sd registration failed: %d\n",
+ ret);
+ gpio_free(DA830_MMCSD_WP_PIN);
+ }
+}
+
+/*
+ * UI board NAND/NOR flashes only use 8-bit data bus.
+ */
+static const short da830_evm_emif25_pins[] = {
+ DA830_EMA_D_0, DA830_EMA_D_1, DA830_EMA_D_2, DA830_EMA_D_3,
+ DA830_EMA_D_4, DA830_EMA_D_5, DA830_EMA_D_6, DA830_EMA_D_7,
+ DA830_EMA_A_0, DA830_EMA_A_1, DA830_EMA_A_2, DA830_EMA_A_3,
+ DA830_EMA_A_4, DA830_EMA_A_5, DA830_EMA_A_6, DA830_EMA_A_7,
+ DA830_EMA_A_8, DA830_EMA_A_9, DA830_EMA_A_10, DA830_EMA_A_11,
+ DA830_EMA_A_12, DA830_EMA_BA_0, DA830_EMA_BA_1, DA830_NEMA_WE,
+ DA830_NEMA_CS_2, DA830_NEMA_CS_3, DA830_NEMA_OE, DA830_EMA_WAIT_0,
+ -1
+};
+
+#if defined(CONFIG_MMC_DAVINCI) || defined(CONFIG_MMC_DAVINCI_MODULE)
+#define HAS_MMC 1
+#else
+#define HAS_MMC 0
+#endif
+
+#ifdef CONFIG_DA830_UI_NAND
+static struct mtd_partition da830_evm_nand_partitions[] = {
+ /* bootloader (U-Boot, etc) in first sector */
+ [0] = {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ /* bootloader params in the next sector */
+ [1] = {
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_128K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ /* kernel */
+ [2] = {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_2M,
+ .mask_flags = 0,
+ },
+ /* file system */
+ [3] = {
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ }
+};
+
+/* flash bbt decriptors */
+static uint8_t da830_evm_nand_bbt_pattern[] = { 'B', 'b', 't', '0' };
+static uint8_t da830_evm_nand_mirror_pattern[] = { '1', 't', 'b', 'B' };
+
+static struct nand_bbt_descr da830_evm_nand_bbt_main_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
+ NAND_BBT_WRITE | NAND_BBT_2BIT |
+ NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 2,
+ .len = 4,
+ .veroffs = 16,
+ .maxblocks = 4,
+ .pattern = da830_evm_nand_bbt_pattern
+};
+
+static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
+ NAND_BBT_WRITE | NAND_BBT_2BIT |
+ NAND_BBT_VERSION | NAND_BBT_PERCHIP,
+ .offs = 2,
+ .len = 4,
+ .veroffs = 16,
+ .maxblocks = 4,
+ .pattern = da830_evm_nand_mirror_pattern
+};
+
+static struct davinci_nand_pdata da830_evm_nand_pdata = {
+ .parts = da830_evm_nand_partitions,
+ .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions),
+ .ecc_mode = NAND_ECC_HW,
+ .ecc_bits = 4,
+ .options = NAND_USE_FLASH_BBT,
+ .bbt_td = &da830_evm_nand_bbt_main_descr,
+ .bbt_md = &da830_evm_nand_bbt_mirror_descr,
+};
+
+static struct resource da830_evm_nand_resources[] = {
+ [0] = { /* First memory resource is NAND I/O window */
+ .start = DA830_EMIF25_ASYNC_DATA_CE3_BASE,
+ .end = DA830_EMIF25_ASYNC_DATA_CE3_BASE + PAGE_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = { /* Second memory resource is AEMIF control registers */
+ .start = DA830_EMIF25_CONTROL_BASE,
+ .end = DA830_EMIF25_CONTROL_BASE + SZ_32K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device da830_evm_nand_device = {
+ .name = "davinci_nand",
+ .id = 1,
+ .dev = {
+ .platform_data = &da830_evm_nand_pdata,
+ },
+ .num_resources = ARRAY_SIZE(da830_evm_nand_resources),
+ .resource = da830_evm_nand_resources,
+};
+
+static inline void da830_evm_init_nand(int mux_mode)
+{
+ int ret;
+
+ if (HAS_MMC) {
+ pr_warning("WARNING: both MMC/SD and NAND are "
+ "enabled, but they share AEMIF pins.\n"
+ "\tDisable MMC/SD for NAND support.\n");
+ return;
+ }
+
+ ret = da8xx_pinmux_setup(da830_evm_emif25_pins);
+ if (ret)
+ pr_warning("da830_evm_init: emif25 mux setup failed: %d\n",
+ ret);
+
+ ret = platform_device_register(&da830_evm_nand_device);
+ if (ret)
+ pr_warning("da830_evm_init: NAND device not registered.\n");
+
+ gpio_direction_output(mux_mode, 1);
+}
+#else
+static inline void da830_evm_init_nand(int mux_mode) { }
+#endif
+
+#ifdef CONFIG_DA830_UI_LCD
+static inline void da830_evm_init_lcdc(int mux_mode)
+{
+ int ret;
+
+ ret = da8xx_pinmux_setup(da830_lcdcntl_pins);
+ if (ret)
+ pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n",
+ ret);
+
+ ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata);
+ if (ret)
+ pr_warning("da830_evm_init: lcd setup failed: %d\n", ret);
+
+ gpio_direction_output(mux_mode, 0);
+}
+#else
+static inline void da830_evm_init_lcdc(int mux_mode) { }
+#endif
+
+static struct at24_platform_data da830_evm_i2c_eeprom_info = {
+ .byte_len = SZ_256K / 8,
+ .page_size = 64,
+ .flags = AT24_FLAG_ADDR16,
+ .setup = davinci_get_mac_addr,
+ .context = (void *)0x7f00,
+};
+
+static int __init da830_evm_ui_expander_setup(struct i2c_client *client,
+ int gpio, unsigned ngpio, void *context)
+{
+ gpio_request(gpio + 6, "UI MUX_MODE");
+
+ /* Drive mux mode low to match the default without UI card */
+ gpio_direction_output(gpio + 6, 0);
+
+ da830_evm_init_lcdc(gpio + 6);
+
+ da830_evm_init_nand(gpio + 6);
+
+ return 0;
+}
+
+static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
+ unsigned ngpio, void *context)
+{
+ gpio_free(gpio + 6);
+ return 0;
+}
+
+static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = {
+ .gpio_base = DAVINCI_N_GPIO,
+ .setup = da830_evm_ui_expander_setup,
+ .teardown = da830_evm_ui_expander_teardown,
+};
+
+static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("24c256", 0x50),
+ .platform_data = &da830_evm_i2c_eeprom_info,
+ },
+ {
+ I2C_BOARD_INFO("tlv320aic3x", 0x18),
+ },
+ {
+ I2C_BOARD_INFO("pcf8574", 0x3f),
+ .platform_data = &da830_evm_ui_expander_info,
+ },
+};
+
+static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
+ .bus_freq = 100, /* kHz */
+ .bus_delay = 0, /* usec */
+};
+
static __init void da830_evm_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
pr_warning("da830_evm_init: i2c0 registration failed: %d\n",
ret);
+ da830_evm_usb_init();
+
soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->rmii_en = 1;
i2c_register_board_info(1, da830_evm_i2c_devices,
ARRAY_SIZE(da830_evm_i2c_devices));
- ret = da8xx_pinmux_setup(da830_mcasp1_pins);
+ ret = da8xx_pinmux_setup(da830_evm_mcasp1_pins);
if (ret)
pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n",
ret);
- da8xx_init_mcasp(1, &da830_evm_snd_data);
+ da8xx_register_mcasp(1, &da830_evm_snd_data);
+
+ da830_evm_init_mmc();
+
+ ret = da8xx_register_rtc();
+ if (ret)
+ pr_warning("da830_evm_init: rtc setup failed: %d\n", ret);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
da830_init();
}
-MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP L137 EVM")
+MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM")
.phys_io = IO_PHYS,
.io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
.boot_params = (DA8XX_DDR_BASE + 0x100),
* or implied.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
+#include <linux/i2c/pca953x.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
+#include <linux/regulator/machine.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <mach/common.h>
-#include <mach/irqs.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/nand.h>
+#include <mach/mux.h>
#define DA850_EVM_PHY_MASK 0x1
#define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
+#define DA850_LCD_PWR_PIN GPIO_TO_PIN(2, 8)
#define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15)
-#define DA850_LCD_PWR_PIN GPIO_TO_PIN(8, 10)
#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0)
#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1)
+#define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6)
+
static struct mtd_partition da850_evm_norflash_partition[] = {
{
.name = "NOR filesystem",
.resource = da850_evm_nandflash_resource,
};
+static struct platform_device *da850_evm_devices[] __initdata = {
+ &da850_evm_nandflash_device,
+ &da850_evm_norflash_device,
+};
+
+#define DA8XX_AEMIF_CE2CFG_OFFSET 0x10
+#define DA8XX_AEMIF_ASIZE_16BIT 0x1
+
+static void __init da850_evm_init_nor(void)
+{
+ void __iomem *aemif_addr;
+
+ aemif_addr = ioremap(DA8XX_AEMIF_CTL_BASE, SZ_32K);
+
+ /* Configure data bus width of CS2 to 16 bit */
+ writel(readl(aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET) |
+ DA8XX_AEMIF_ASIZE_16BIT,
+ aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET);
+
+ iounmap(aemif_addr);
+}
+
+static u32 ui_card_detected;
+
+#if defined(CONFIG_MMC_DAVINCI) || \
+ defined(CONFIG_MMC_DAVINCI_MODULE)
+#define HAS_MMC 1
+#else
+#define HAS_MMC 0
+#endif
+
+static __init void da850_evm_setup_nor_nand(void)
+{
+ int ret = 0;
+
+ if (ui_card_detected & !HAS_MMC) {
+ ret = da8xx_pinmux_setup(da850_nand_pins);
+ if (ret)
+ pr_warning("da850_evm_init: nand mux setup failed: "
+ "%d\n", ret);
+
+ ret = da8xx_pinmux_setup(da850_nor_pins);
+ if (ret)
+ pr_warning("da850_evm_init: nor mux setup failed: %d\n",
+ ret);
+
+ da850_evm_init_nor();
+
+ platform_add_devices(da850_evm_devices,
+ ARRAY_SIZE(da850_evm_devices));
+ }
+}
+
+#ifdef CONFIG_DA850_UI_RMII
+static inline void da850_evm_setup_emac_rmii(int rmii_sel)
+{
+ struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+ soc_info->emac_pdata->rmii_en = 1;
+ gpio_set_value(rmii_sel, 0);
+}
+#else
+static inline void da850_evm_setup_emac_rmii(int rmii_sel) { }
+#endif
+
+static int da850_evm_ui_expander_setup(struct i2c_client *client, unsigned gpio,
+ unsigned ngpio, void *c)
+{
+ int sel_a, sel_b, sel_c, ret;
+
+ sel_a = gpio + 7;
+ sel_b = gpio + 6;
+ sel_c = gpio + 5;
+
+ ret = gpio_request(sel_a, "sel_a");
+ if (ret) {
+ pr_warning("Cannot open UI expander pin %d\n", sel_a);
+ goto exp_setup_sela_fail;
+ }
+
+ ret = gpio_request(sel_b, "sel_b");
+ if (ret) {
+ pr_warning("Cannot open UI expander pin %d\n", sel_b);
+ goto exp_setup_selb_fail;
+ }
+
+ ret = gpio_request(sel_c, "sel_c");
+ if (ret) {
+ pr_warning("Cannot open UI expander pin %d\n", sel_c);
+ goto exp_setup_selc_fail;
+ }
+
+ /* deselect all functionalities */
+ gpio_direction_output(sel_a, 1);
+ gpio_direction_output(sel_b, 1);
+ gpio_direction_output(sel_c, 1);
+
+ ui_card_detected = 1;
+ pr_info("DA850/OMAP-L138 EVM UI card detected\n");
+
+ da850_evm_setup_nor_nand();
+
+ da850_evm_setup_emac_rmii(sel_a);
+
+ return 0;
+
+exp_setup_selc_fail:
+ gpio_free(sel_b);
+exp_setup_selb_fail:
+ gpio_free(sel_a);
+exp_setup_sela_fail:
+ return ret;
+}
+
+static int da850_evm_ui_expander_teardown(struct i2c_client *client,
+ unsigned gpio, unsigned ngpio, void *c)
+{
+ /* deselect all functionalities */
+ gpio_set_value(gpio + 5, 1);
+ gpio_set_value(gpio + 6, 1);
+ gpio_set_value(gpio + 7, 1);
+
+ gpio_free(gpio + 5);
+ gpio_free(gpio + 6);
+ gpio_free(gpio + 7);
+
+ return 0;
+}
+
+static struct pca953x_platform_data da850_evm_ui_expander_info = {
+ .gpio_base = DAVINCI_N_GPIO,
+ .setup = da850_evm_ui_expander_setup,
+ .teardown = da850_evm_ui_expander_teardown,
+};
+
static struct i2c_board_info __initdata da850_evm_i2c_devices[] = {
{
I2C_BOARD_INFO("tlv320aic3x", 0x18),
- }
+ },
+ {
+ I2C_BOARD_INFO("tca6416", 0x20),
+ .platform_data = &da850_evm_ui_expander_info,
+ },
};
static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = {
.enabled_uarts = 0x7,
};
-static struct platform_device *da850_evm_devices[] __initdata = {
- &da850_evm_nandflash_device,
- &da850_evm_norflash_device,
-};
-
/* davinci da850 evm audio machine driver */
static u8 da850_iis_serializer_direction[] = {
INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
.get_ro = da850_evm_mmc_get_ro,
.get_cd = da850_evm_mmc_get_cd,
.wires = 4,
+ .max_freq = 50000000,
+ .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
.version = MMC_CTLR_VERSION_2,
};
return 0;
}
-#define DA8XX_AEMIF_CE2CFG_OFFSET 0x10
-#define DA8XX_AEMIF_ASIZE_16BIT 0x1
+/* TPS65070 voltage regulator support */
-static void __init da850_evm_init_nor(void)
-{
- void __iomem *aemif_addr;
+/* 3.3V */
+struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
+ {
+ .supply = "usb0_vdda33",
+ },
+ {
+ .supply = "usb1_vdda33",
+ },
+};
- aemif_addr = ioremap(DA8XX_AEMIF_CTL_BASE, SZ_32K);
+/* 3.3V or 1.8V */
+struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
+ {
+ .supply = "dvdd3318_a",
+ },
+ {
+ .supply = "dvdd3318_b",
+ },
+ {
+ .supply = "dvdd3318_c",
+ },
+};
- /* Configure data bus width of CS2 to 16 bit */
- writel(readl(aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET) |
- DA8XX_AEMIF_ASIZE_16BIT,
- aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET);
+/* 1.2V */
+struct regulator_consumer_supply tps65070_dcdc3_consumers[] = {
+ {
+ .supply = "cvdd",
+ },
+};
- iounmap(aemif_addr);
-}
+/* 1.8V LDO */
+struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
+ {
+ .supply = "sata_vddr",
+ },
+ {
+ .supply = "usb0_vdda18",
+ },
+ {
+ .supply = "usb1_vdda18",
+ },
+ {
+ .supply = "ddr_dvdd18",
+ },
+};
-#if defined(CONFIG_MTD_PHYSMAP) || \
- defined(CONFIG_MTD_PHYSMAP_MODULE)
-#define HAS_NOR 1
-#else
-#define HAS_NOR 0
-#endif
+/* 1.2V LDO */
+struct regulator_consumer_supply tps65070_ldo2_consumers[] = {
+ {
+ .supply = "sata_vdd",
+ },
+ {
+ .supply = "pll0_vdda",
+ },
+ {
+ .supply = "pll1_vdda",
+ },
+ {
+ .supply = "usbs_cvdd",
+ },
+ {
+ .supply = "vddarnwa1",
+ },
+};
-#if defined(CONFIG_MMC_DAVINCI) || \
- defined(CONFIG_MMC_DAVINCI_MODULE)
-#define HAS_MMC 1
-#else
-#define HAS_MMC 0
-#endif
+struct regulator_init_data tps65070_regulator_data[] = {
+ /* dcdc1 */
+ {
+ .constraints = {
+ .min_uV = 3150000,
+ .max_uV = 3450000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc1_consumers),
+ .consumer_supplies = tps65070_dcdc1_consumers,
+ },
-static __init void da850_evm_init(void)
+ /* dcdc2 */
+ {
+ .constraints = {
+ .min_uV = 1710000,
+ .max_uV = 3450000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc2_consumers),
+ .consumer_supplies = tps65070_dcdc2_consumers,
+ },
+
+ /* dcdc3 */
+ {
+ .constraints = {
+ .min_uV = 950000,
+ .max_uV = 1320000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc3_consumers),
+ .consumer_supplies = tps65070_dcdc3_consumers,
+ },
+
+ /* ldo1 */
+ {
+ .constraints = {
+ .min_uV = 1710000,
+ .max_uV = 1890000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65070_ldo1_consumers),
+ .consumer_supplies = tps65070_ldo1_consumers,
+ },
+
+ /* ldo2 */
+ {
+ .constraints = {
+ .min_uV = 1140000,
+ .max_uV = 1320000,
+ .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
+ REGULATOR_CHANGE_STATUS),
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(tps65070_ldo2_consumers),
+ .consumer_supplies = tps65070_ldo2_consumers,
+ },
+};
+
+static struct i2c_board_info __initdata da850evm_tps65070_info[] = {
+ {
+ I2C_BOARD_INFO("tps6507x", 0x48),
+ .platform_data = &tps65070_regulator_data[0],
+ },
+};
+
+static int __init pmic_tps65070_init(void)
{
- struct davinci_soc_info *soc_info = &davinci_soc_info;
+ return i2c_register_board_info(1, da850evm_tps65070_info,
+ ARRAY_SIZE(da850evm_tps65070_info));
+}
+
+static const short da850_evm_lcdc_pins[] = {
+ DA850_GPIO2_8, DA850_GPIO2_15,
+ -1
+};
+
+static int __init da850_evm_config_emac(void)
+{
+ void __iomem *cfg_chip3_base;
int ret;
+ u32 val;
+ struct davinci_soc_info *soc_info = &davinci_soc_info;
+ u8 rmii_en = soc_info->emac_pdata->rmii_en;
+
+ if (!machine_is_davinci_da850_evm())
+ return 0;
+
+ cfg_chip3_base = DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP3_REG);
+
+ val = __raw_readl(cfg_chip3_base);
+
+ if (rmii_en) {
+ val |= BIT(8);
+ ret = da8xx_pinmux_setup(da850_rmii_pins);
+ pr_info("EMAC: RMII PHY configured, MII PHY will not be"
+ " functional\n");
+ } else {
+ val &= ~BIT(8);
+ ret = da8xx_pinmux_setup(da850_cpgmac_pins);
+ pr_info("EMAC: MII PHY configured, RMII PHY will not be"
+ " functional\n");
+ }
- ret = da8xx_pinmux_setup(da850_nand_pins);
if (ret)
- pr_warning("da850_evm_init: nand mux setup failed: %d\n",
+ pr_warning("da850_evm_init: cpgmac/rmii mux setup failed: %d\n",
ret);
- ret = da8xx_pinmux_setup(da850_nor_pins);
+ /* configure the CFGCHIP3 register for RMII or MII */
+ __raw_writel(val, cfg_chip3_base);
+
+ ret = davinci_cfg_reg(DA850_GPIO2_6);
if (ret)
- pr_warning("da850_evm_init: nor mux setup failed: %d\n",
+ pr_warning("da850_evm_init:GPIO(2,6) mux setup "
+ "failed\n");
+
+ ret = gpio_request(DA850_MII_MDIO_CLKEN_PIN, "mdio_clk_en");
+ if (ret) {
+ pr_warning("Cannot open GPIO %d\n",
+ DA850_MII_MDIO_CLKEN_PIN);
+ return ret;
+ }
+
+ /* Enable/Disable MII MDIO clock */
+ gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, rmii_en);
+
+ soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK;
+ soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY;
+
+ ret = da8xx_register_emac();
+ if (ret)
+ pr_warning("da850_evm_init: emac registration failed: %d\n",
ret);
- da850_evm_init_nor();
+ return 0;
+}
+device_initcall(da850_evm_config_emac);
+
+static __init void da850_evm_init(void)
+{
+ int ret;
- platform_add_devices(da850_evm_devices,
- ARRAY_SIZE(da850_evm_devices));
+ ret = pmic_tps65070_init();
+ if (ret)
+ pr_warning("da850_evm_init: TPS65070 PMIC init failed: %d\n",
+ ret);
ret = da8xx_register_edma();
if (ret)
pr_warning("da850_evm_init: i2c0 registration failed: %d\n",
ret);
- soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK;
- soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY;
- soc_info->emac_pdata->rmii_en = 0;
-
- ret = da8xx_pinmux_setup(da850_cpgmac_pins);
- if (ret)
- pr_warning("da850_evm_init: cpgmac mux setup failed: %d\n",
- ret);
-
- ret = da8xx_register_emac();
- if (ret)
- pr_warning("da850_evm_init: emac registration failed: %d\n",
- ret);
ret = da8xx_register_watchdog();
if (ret)
ret);
if (HAS_MMC) {
- if (HAS_NOR)
- pr_warning("WARNING: both NOR Flash and MMC/SD are "
- "enabled, but they share AEMIF pins.\n"
- "\tDisable one of them.\n");
-
ret = da8xx_pinmux_setup(da850_mmcsd0_pins);
if (ret)
pr_warning("da850_evm_init: mmcsd0 mux setup failed:"
pr_warning("da850_evm_init: mcasp mux setup failed: %d\n",
ret);
- da8xx_init_mcasp(0, &da850_evm_snd_data);
+ da8xx_register_mcasp(0, &da850_evm_snd_data);
ret = da8xx_pinmux_setup(da850_lcdcntl_pins);
if (ret)
pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n",
ret);
+ /* Handle board specific muxing for LCD here */
+ ret = da8xx_pinmux_setup(da850_evm_lcdc_pins);
+ if (ret)
+ pr_warning("da850_evm_init: evm specific lcd mux setup "
+ "failed: %d\n", ret);
+
ret = da850_lcd_hw_init();
if (ret)
pr_warning("da850_evm_init: lcd initialization failed: %d\n",
ret);
- ret = da8xx_register_lcdc();
+ ret = da8xx_register_lcdc(&sharp_lk043t1dg01_pdata);
if (ret)
pr_warning("da850_evm_init: lcdc registration failed: %d\n",
ret);
+
+ ret = da8xx_register_rtc();
+ if (ret)
+ pr_warning("da850_evm_init: rtc setup failed: %d\n", ret);
+
+ ret = da850_register_cpufreq();
+ if (ret)
+ pr_warning("da850_evm_init: cpufreq registration failed: %d\n",
+ ret);
+
+ ret = da8xx_register_cpuidle();
+ if (ret)
+ pr_warning("da850_evm_init: cpuidle registration failed: %d\n",
+ ret);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
* or implied.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
-#include <linux/dma-mapping.h>
+#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/i2c.h>
-#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/clk.h>
#include <linux/videodev2.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
-#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <mach/hardware.h>
#include <mach/dm355.h>
-#include <mach/psc.h>
-#include <mach/common.h>
#include <mach/i2c.h>
#include <mach/serial.h>
#include <mach/nand.h>
#include <mach/mmc.h>
+#include <mach/usb.h>
#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000
#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000
.mask_chipsel = BIT(14),
.parts = davinci_nand_partitions,
.nr_parts = ARRAY_SIZE(davinci_nand_partitions),
- .ecc_mode = NAND_ECC_HW_SYNDROME,
+ .ecc_mode = NAND_ECC_HW,
.options = NAND_USE_FLASH_BBT,
+ .ecc_bits = 4,
};
static struct resource davinci_nand_resources[] = {
gpio_request(2, "usb_id_toggle");
gpio_direction_output(2, USB_ID_VALUE);
/* irlml6401 switches over 1A in under 8 msec */
- setup_usb(500, 8);
+ davinci_setup_usb(1000, 8);
davinci_setup_mmc(0, &dm355evm_mmc_config);
davinci_setup_mmc(1, &dm355evm_mmc_config);
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
-#include <linux/dma-mapping.h>
+#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/i2c.h>
-#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
-#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <mach/hardware.h>
#include <mach/dm355.h>
-#include <mach/psc.h>
-#include <mach/common.h>
#include <mach/i2c.h>
#include <mach/serial.h>
#include <mach/nand.h>
#include <mach/mmc.h>
+#include <mach/usb.h>
#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000
#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000
gpio_request(2, "usb_id_toggle");
gpio_direction_output(2, USB_ID_VALUE);
/* irlml6401 switches over 1A in under 8 msec */
- setup_usb(500, 8);
+ davinci_setup_usb(1000, 8);
davinci_setup_mmc(0, &dm355leopard_mmc_config);
davinci_setup_mmc(1, &dm355leopard_mmc_config);
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
-#include <linux/dma-mapping.h>
+#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
-#include <asm/setup.h>
+#include <linux/input.h>
+
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
+
#include <mach/mux.h>
-#include <mach/hardware.h>
#include <mach/dm365.h>
-#include <mach/psc.h>
#include <mach/common.h>
#include <mach/i2c.h>
#include <mach/serial.h>
#include <mach/mmc.h>
#include <mach/nand.h>
-
+#include <mach/keyscan.h>
static inline int have_imager(void)
{
.nr_parts = ARRAY_SIZE(davinci_nand_partitions),
.ecc_mode = NAND_ECC_HW,
.options = NAND_USE_FLASH_BBT,
+ .ecc_bits = 4,
};
static struct resource davinci_nand_resources[] = {
.context = (void *)0x7f00,
};
+static struct snd_platform_data dm365_evm_snd_data;
+
static struct i2c_board_info i2c_info[] = {
{
I2C_BOARD_INFO("24c256", 0x50),
.platform_data = &eeprom_info,
},
+ {
+ I2C_BOARD_INFO("tlv320aic3x", 0x18),
+ },
};
static struct davinci_i2c_platform_data i2c_pdata = {
.bus_delay = 0 /* usec */,
};
+#ifdef CONFIG_KEYBOARD_DAVINCI
+static unsigned short dm365evm_keymap[] = {
+ KEY_KP2,
+ KEY_LEFT,
+ KEY_EXIT,
+ KEY_DOWN,
+ KEY_ENTER,
+ KEY_UP,
+ KEY_KP1,
+ KEY_RIGHT,
+ KEY_MENU,
+ KEY_RECORD,
+ KEY_REWIND,
+ KEY_KPMINUS,
+ KEY_STOP,
+ KEY_FASTFORWARD,
+ KEY_KPPLUS,
+ KEY_PLAYPAUSE,
+ 0
+};
+
+static struct davinci_ks_platform_data dm365evm_ks_data = {
+ .keymap = dm365evm_keymap,
+ .keymapsize = ARRAY_SIZE(dm365evm_keymap),
+ .rep = 1,
+ /* Scan period = strobe + interval */
+ .strobe = 0x5,
+ .interval = 0x2,
+ .matrix_type = DAVINCI_KEYSCAN_MATRIX_4X4,
+};
+#endif
+
static int cpld_mmc_get_cd(int module)
{
if (!cpld)
/* maybe setup mmc1/etc ... _after_ mmc0 */
evm_init_cpld();
+
+ dm365_init_asp(&dm365_evm_snd_data);
+ dm365_init_rtc();
+
+#ifdef CONFIG_KEYBOARD_DAVINCI
+ dm365_init_ks(&dm365evm_ks_data);
+#endif
}
static __init void dm365_evm_irq_init(void)
* or implied.
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/memory.h>
-
#include <linux/i2c.h>
#include <linux/i2c/pcf857x.h>
#include <linux/i2c/at24.h>
-#include <linux/etherdevice.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-#include <linux/io.h>
#include <linux/phy.h>
#include <linux/clk.h>
#include <linux/videodev2.h>
#include <media/tvp514x.h>
-#include <asm/setup.h>
#include <asm/mach-types.h>
-
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
#include <mach/dm644x.h>
#include <mach/common.h>
#include <mach/i2c.h>
#include <mach/serial.h>
#include <mach/mux.h>
-#include <mach/psc.h>
#include <mach/nand.h>
#include <mach/mmc.h>
-#include <mach/emac.h>
+#include <mach/usb.h>
#define DM644X_EVM_PHY_MASK (0x2)
#define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
/* irlml6401 switches over 1A, in under 8 msec;
* now it can be managed by nDRV_VBUS ...
*/
- setup_usb(500, 8);
+ davinci_setup_usb(1000, 8);
return 0;
}
**************************************************************************/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
-#include <linux/fs.h>
-#include <linux/major.h>
-#include <linux/root_dev.h>
-#include <linux/dma-mapping.h>
-#include <linux/serial.h>
-#include <linux/serial_8250.h>
#include <linux/leds.h>
#include <linux/gpio.h>
-#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
#include <linux/i2c/pcf857x.h>
-#include <linux/etherdevice.h>
#include <media/tvp514x.h>
-#include <asm/setup.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
#include <mach/dm646x.h>
#include <mach/common.h>
-#include <mach/psc.h>
#include <mach/serial.h>
#include <mach/i2c.h>
-#include <mach/mmc.h>
-#include <mach/emac.h>
+#include <mach/nand.h>
#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE)
#define HAS_ATA 0
#endif
+#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x20008000
+#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x42000000
+
+#define NAND_BLOCK_SIZE SZ_128K
+
/* CPLD Register 0 bits to control ATA */
#define DM646X_EVM_ATA_RST BIT(0)
#define DM646X_EVM_ATA_PWD BIT(1)
.enabled_uarts = (1 << 0),
};
+/* Note: We are setting first partition as 'bootloader' constituting UBL, U-Boot
+ * and U-Boot environment this avoids dependency on any particular combination
+ * of UBL, U-Boot or flashing tools etc.
+ */
+static struct mtd_partition davinci_nand_partitions[] = {
+ {
+ /* UBL, U-Boot with environment */
+ .name = "bootloader",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 16 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ }, {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_4M,
+ .mask_flags = 0,
+ }, {
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ }
+};
+
+static struct davinci_nand_pdata davinci_nand_data = {
+ .mask_cle = 0x80000,
+ .mask_ale = 0x40000,
+ .parts = davinci_nand_partitions,
+ .nr_parts = ARRAY_SIZE(davinci_nand_partitions),
+ .ecc_mode = NAND_ECC_HW,
+ .options = 0,
+};
+
+static struct resource davinci_nand_resources[] = {
+ {
+ .start = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE,
+ .end = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = DAVINCI_ASYNC_EMIF_CONTROL_BASE,
+ .end = DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device davinci_nand_device = {
+ .name = "davinci_nand",
+ .id = 0,
+
+ .num_resources = ARRAY_SIZE(davinci_nand_resources),
+ .resource = davinci_nand_resources,
+
+ .dev = {
+ .platform_data = &davinci_nand_data,
+ },
+};
+
/* CPLD Register 0 Client: used for I/O Control */
static int cpld_reg0_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{ .name = "DS4", .active_low = 1, },
};
-static __initconst struct gpio_led_platform_data evm_led_data = {
+static const struct gpio_led_platform_data evm_led_data = {
.num_leds = ARRAY_SIZE(evm_leds),
.leds = evm_leds,
};
dm646x_init_mcasp0(&dm646x_evm_snd_data[0]);
dm646x_init_mcasp1(&dm646x_evm_snd_data[1]);
+ platform_device_register(&davinci_nand_device);
+
if (HAS_ATA)
dm646x_init_ide();
--- /dev/null
+/*
+ * Neuros Technologies OSD2 board support
+ *
+ * Modified from original 644X-EVM board support.
+ * 2008 (c) Neuros Technology, LLC.
+ * 2009 (c) Jorge Luis Zapata Muga <jorgeluis.zapata@gmail.com>
+ * 2009 (c) Andrey A. Porodko <Andrey.Porodko@gmail.com>
+ *
+ * The Neuros OSD 2.0 is the hardware component of the Neuros Open
+ * Internet Television Platform. Hardware is very close to TI
+ * DM644X-EVM board. It has:
+ * DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
+ * USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
+ * Additionaly realtime clock, IR remote control receiver,
+ * IR Blaster based on MSP430 (firmware although is different
+ * from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
+ * with PATA interface, two muxed red-green leds.
+ *
+ * For more information please refer to
+ * http://wiki.neurostechnology.com/index.php/OSD_2.0_HD
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/dm644x.h>
+#include <mach/i2c.h>
+#include <mach/serial.h>
+#include <mach/mux.h>
+#include <mach/nand.h>
+#include <mach/mmc.h>
+#include <mach/usb.h>
+
+#define NEUROS_OSD2_PHY_MASK 0x2
+#define NEUROS_OSD2_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
+
+#define DAVINCI_CFC_ATA_BASE 0x01C66000
+
+#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e00000
+#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000
+
+#define LXT971_PHY_ID 0x001378e2
+#define LXT971_PHY_MASK 0xfffffff0
+
+#define NTOSD2_AUDIOSOC_I2C_ADDR 0x18
+#define NTOSD2_MSP430_I2C_ADDR 0x59
+#define NTOSD2_MSP430_IRQ 2
+
+/* Neuros OSD2 has a Samsung 256 MByte NAND flash (Dev ID of 0xAA,
+ * 2048 blocks in the device, 64 pages per block, 2048 bytes per
+ * page.
+ */
+
+#define NAND_BLOCK_SIZE SZ_128K
+
+struct mtd_partition davinci_ntosd2_nandflash_partition[] = {
+ {
+ /* UBL (a few copies) plus U-Boot */
+ .name = "bootloader",
+ .offset = 0,
+ .size = 15 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ }, {
+ /* U-Boot environment */
+ .name = "params",
+ .offset = MTDPART_OFS_APPEND,
+ .size = 1 * NAND_BLOCK_SIZE,
+ .mask_flags = 0,
+ }, {
+ /* Kernel */
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_4M,
+ .mask_flags = 0,
+ }, {
+ /* File System */
+ .name = "filesystem",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ }
+ /* A few blocks at end hold a flash Bad Block Table. */
+};
+
+static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = {
+ .parts = davinci_ntosd2_nandflash_partition,
+ .nr_parts = ARRAY_SIZE(davinci_ntosd2_nandflash_partition),
+ .ecc_mode = NAND_ECC_HW,
+ .options = NAND_USE_FLASH_BBT,
+};
+
+static struct resource davinci_ntosd2_nandflash_resource[] = {
+ {
+ .start = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE,
+ .end = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = DAVINCI_ASYNC_EMIF_CONTROL_BASE,
+ .end = DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device davinci_ntosd2_nandflash_device = {
+ .name = "davinci_nand",
+ .id = 0,
+ .dev = {
+ .platform_data = &davinci_ntosd2_nandflash_data,
+ },
+ .num_resources = ARRAY_SIZE(davinci_ntosd2_nandflash_resource),
+ .resource = davinci_ntosd2_nandflash_resource,
+};
+
+static u64 davinci_fb_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device davinci_fb_device = {
+ .name = "davincifb",
+ .id = -1,
+ .dev = {
+ .dma_mask = &davinci_fb_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = 0,
+};
+
+static struct resource ide_resources[] = {
+ {
+ .start = DAVINCI_CFC_ATA_BASE,
+ .end = DAVINCI_CFC_ATA_BASE + 0x7ff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_IDE,
+ .end = IRQ_IDE,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 ide_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device ide_dev = {
+ .name = "palm_bk3710",
+ .id = -1,
+ .resource = ide_resources,
+ .num_resources = ARRAY_SIZE(ide_resources),
+ .dev = {
+ .dma_mask = &ide_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+static struct snd_platform_data dm644x_ntosd2_snd_data;
+
+static struct gpio_led ntosd2_leds[] = {
+ { .name = "led1_green", .gpio = GPIO(10), },
+ { .name = "led1_red", .gpio = GPIO(11), },
+ { .name = "led2_green", .gpio = GPIO(12), },
+ { .name = "led2_red", .gpio = GPIO(13), },
+};
+
+static struct gpio_led_platform_data ntosd2_leds_data = {
+ .num_leds = ARRAY_SIZE(ntosd2_leds),
+ .leds = ntosd2_leds,
+};
+
+static struct platform_device ntosd2_leds_dev = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &ntosd2_leds_data,
+ },
+};
+
+
+static struct platform_device *davinci_ntosd2_devices[] __initdata = {
+ &davinci_fb_device,
+ &ntosd2_leds_dev,
+};
+
+static struct davinci_uart_config uart_config __initdata = {
+ .enabled_uarts = (1 << 0),
+};
+
+static void __init davinci_ntosd2_map_io(void)
+{
+ dm644x_init();
+}
+
+/*
+ I2C initialization
+*/
+static struct davinci_i2c_platform_data ntosd2_i2c_pdata = {
+ .bus_freq = 20 /* kHz */,
+ .bus_delay = 100 /* usec */,
+};
+
+static struct i2c_board_info __initdata ntosd2_i2c_info[] = {
+};
+
+static int ntosd2_init_i2c(void)
+{
+ int status;
+
+ davinci_init_i2c(&ntosd2_i2c_pdata);
+ status = gpio_request(NTOSD2_MSP430_IRQ, ntosd2_i2c_info[0].type);
+ if (status == 0) {
+ status = gpio_direction_input(NTOSD2_MSP430_IRQ);
+ if (status == 0) {
+ status = gpio_to_irq(NTOSD2_MSP430_IRQ);
+ if (status > 0) {
+ ntosd2_i2c_info[0].irq = status;
+ i2c_register_board_info(1,
+ ntosd2_i2c_info,
+ ARRAY_SIZE(ntosd2_i2c_info));
+ }
+ }
+ }
+ return status;
+}
+
+static struct davinci_mmc_config davinci_ntosd2_mmc_config = {
+ .wires = 4,
+ .version = MMC_CTLR_VERSION_1
+};
+
+
+#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
+ defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE)
+#define HAS_ATA 1
+#else
+#define HAS_ATA 0
+#endif
+
+#if defined(CONFIG_MTD_NAND_DAVINCI) || \
+ defined(CONFIG_MTD_NAND_DAVINCI_MODULE)
+#define HAS_NAND 1
+#else
+#define HAS_NAND 0
+#endif
+
+static __init void davinci_ntosd2_init(void)
+{
+ struct clk *aemif_clk;
+ struct davinci_soc_info *soc_info = &davinci_soc_info;
+ int status;
+
+ aemif_clk = clk_get(NULL, "aemif");
+ clk_enable(aemif_clk);
+
+ if (HAS_ATA) {
+ if (HAS_NAND)
+ pr_warning("WARNING: both IDE and Flash are "
+ "enabled, but they share AEMIF pins.\n"
+ "\tDisable IDE for NAND/NOR support.\n");
+ davinci_cfg_reg(DM644X_HPIEN_DISABLE);
+ davinci_cfg_reg(DM644X_ATAEN);
+ davinci_cfg_reg(DM644X_HDIREN);
+ platform_device_register(&ide_dev);
+ } else if (HAS_NAND) {
+ davinci_cfg_reg(DM644X_HPIEN_DISABLE);
+ davinci_cfg_reg(DM644X_ATAEN_DISABLE);
+
+ /* only one device will be jumpered and detected */
+ if (HAS_NAND)
+ platform_device_register(
+ &davinci_ntosd2_nandflash_device);
+ }
+
+ platform_add_devices(davinci_ntosd2_devices,
+ ARRAY_SIZE(davinci_ntosd2_devices));
+
+ /* Initialize I2C interface specific for this board */
+ status = ntosd2_init_i2c();
+ if (status < 0)
+ pr_warning("davinci_ntosd2_init: msp430 irq setup failed:"
+ " %d\n", status);
+
+ davinci_serial_init(&uart_config);
+ dm644x_init_asp(&dm644x_ntosd2_snd_data);
+
+ soc_info->emac_pdata->phy_mask = NEUROS_OSD2_PHY_MASK;
+ soc_info->emac_pdata->mdio_max_freq = NEUROS_OSD2_MDIO_FREQUENCY;
+
+ davinci_setup_usb(1000, 8);
+ /*
+ * Mux the pins to be GPIOs, VLYNQEN is already done at startup.
+ * The AEAWx are five new AEAW pins that can be muxed by separately.
+ * They are a bitmask for GPIO management. According TI
+ * documentation (http://www.ti.com/lit/gpn/tms320dm6446) to employ
+ * gpio(10,11,12,13) for leds any combination of bits works except
+ * four last. So we are to reset all five.
+ */
+ davinci_cfg_reg(DM644X_AEAW0);
+ davinci_cfg_reg(DM644X_AEAW1);
+ davinci_cfg_reg(DM644X_AEAW2);
+ davinci_cfg_reg(DM644X_AEAW3);
+ davinci_cfg_reg(DM644X_AEAW4);
+
+ davinci_setup_mmc(0, &davinci_ntosd2_mmc_config);
+}
+
+static __init void davinci_ntosd2_irq_init(void)
+{
+ davinci_irq_init();
+}
+
+MACHINE_START(NEUROS_OSD2, "Neuros OSD2")
+ /* Maintainer: Neuros Technologies <neuros@groups.google.com> */
+ .phys_io = IO_PHYS,
+ .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
+ .boot_params = (DAVINCI_DDR_BASE + 0x100),
+ .map_io = davinci_ntosd2_map_io,
+ .init_irq = davinci_ntosd2_irq_init,
+ .timer = &davinci_timer,
+ .init_machine = davinci_ntosd2_init,
+MACHINE_END
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
-#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
-
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
-#include <linux/etherdevice.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/io.h>
-#include <asm/setup.h>
#include <asm/mach-types.h>
-
#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <mach/dm644x.h>
#include <mach/common.h>
#include <mach/i2c.h>
#include <mach/serial.h>
-#include <mach/psc.h>
#include <mach/mux.h>
+#include <mach/usb.h>
#define SFFSDR_PHY_MASK (0x2)
#define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
.resource = davinci_sffsdr_nandflash_resource,
};
-static struct emac_platform_data sffsdr_emac_pdata = {
- .phy_mask = SFFSDR_PHY_MASK,
- .mdio_max_freq = SFFSDR_MDIO_FREQUENCY,
-};
-
static struct at24_platform_data eeprom_info = {
.byte_len = (64*1024) / 8,
.page_size = 32,
davinci_serial_init(&uart_config);
soc_info->emac_pdata->phy_mask = SFFSDR_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = SFFSDR_MDIO_FREQUENCY;
- setup_usb(0, 0); /* We support only peripheral mode. */
+ davinci_setup_usb(0, 0); /* We support only peripheral mode. */
/* mux VLYNQ pins */
davinci_cfg_reg(DM644X_VLYNQEN);
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/mutex.h>
-#include <linux/platform_device.h>
#include <linux/io.h>
+#include <linux/delay.h>
#include <mach/hardware.h>
if (clk->parent)
__clk_enable(clk->parent);
if (clk->usecount++ == 0 && (clk->flags & CLK_PSC))
- davinci_psc_config(psc_domain(clk), clk->psc_ctlr,
- clk->lpsc, 1);
+ davinci_psc_config(psc_domain(clk), clk->gpsc, clk->lpsc, 1);
}
static void __clk_disable(struct clk *clk)
if (WARN_ON(clk->usecount == 0))
return;
if (--clk->usecount == 0 && !(clk->flags & CLK_PLL))
- davinci_psc_config(psc_domain(clk), clk->psc_ctlr,
- clk->lpsc, 0);
+ davinci_psc_config(psc_domain(clk), clk->gpsc, clk->lpsc, 0);
if (clk->parent)
__clk_disable(clk->parent);
}
if (clk == NULL || IS_ERR(clk))
return -EINVAL;
+ if (clk->round_rate)
+ return clk->round_rate(clk, rate);
+
return clk->rate;
}
EXPORT_SYMBOL(clk_round_rate);
+/* Propagate rate to children */
+static void propagate_rate(struct clk *root)
+{
+ struct clk *clk;
+
+ list_for_each_entry(clk, &root->children, childnode) {
+ if (clk->recalc)
+ clk->rate = clk->recalc(clk);
+ propagate_rate(clk);
+ }
+}
+
int clk_set_rate(struct clk *clk, unsigned long rate)
{
+ unsigned long flags;
+ int ret = -EINVAL;
+
if (clk == NULL || IS_ERR(clk))
- return -EINVAL;
+ return ret;
- /* changing the clk rate is not supported */
- return -EINVAL;
+ spin_lock_irqsave(&clockfw_lock, flags);
+ if (clk->set_rate)
+ ret = clk->set_rate(clk, rate);
+ if (ret == 0) {
+ if (clk->recalc)
+ clk->rate = clk->recalc(clk);
+ propagate_rate(clk);
+ }
+ spin_unlock_irqrestore(&clockfw_lock, flags);
+
+ return ret;
}
EXPORT_SYMBOL(clk_set_rate);
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ unsigned long flags;
+
+ if (clk == NULL || IS_ERR(clk))
+ return -EINVAL;
+
+ /* Cannot change parent on enabled clock */
+ if (WARN_ON(clk->usecount))
+ return -EINVAL;
+
+ mutex_lock(&clocks_mutex);
+ clk->parent = parent;
+ list_del_init(&clk->childnode);
+ list_add(&clk->childnode, &clk->parent->children);
+ mutex_unlock(&clocks_mutex);
+
+ spin_lock_irqsave(&clockfw_lock, flags);
+ if (clk->recalc)
+ clk->rate = clk->recalc(clk);
+ propagate_rate(clk);
+ spin_unlock_irqrestore(&clockfw_lock, flags);
+
+ return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
int clk_register(struct clk *clk)
{
if (clk == NULL || IS_ERR(clk))
clk->name, clk->parent->name))
return -EINVAL;
+ INIT_LIST_HEAD(&clk->children);
+
mutex_lock(&clocks_mutex);
list_add_tail(&clk->node, &clocks);
+ if (clk->parent)
+ list_add_tail(&clk->childnode, &clk->parent->children);
mutex_unlock(&clocks_mutex);
/* If rate is already set, use it */
if (clk->rate)
return 0;
+ /* Else, see if there is a way to calculate it */
+ if (clk->recalc)
+ clk->rate = clk->recalc(clk);
+
/* Otherwise, default to parent rate */
- if (clk->parent)
+ else if (clk->parent)
clk->rate = clk->parent->rate;
return 0;
mutex_lock(&clocks_mutex);
list_del(&clk->node);
+ list_del(&clk->childnode);
mutex_unlock(&clocks_mutex);
}
EXPORT_SYMBOL(clk_unregister);
continue;
/* ignore if in Disabled or SwRstDisable states */
- if (!davinci_psc_is_clk_active(ck->psc_ctlr, ck->lpsc))
+ if (!davinci_psc_is_clk_active(ck->gpsc, ck->lpsc))
continue;
pr_info("Clocks: disable unused %s\n", ck->name);
- davinci_psc_config(psc_domain(ck), ck->psc_ctlr, ck->lpsc, 0);
+ davinci_psc_config(psc_domain(ck), ck->gpsc, ck->lpsc, 0);
}
spin_unlock_irq(&clockfw_lock);
late_initcall(clk_disable_unused);
#endif
-static void clk_sysclk_recalc(struct clk *clk)
+static unsigned long clk_sysclk_recalc(struct clk *clk)
{
u32 v, plldiv;
struct pll_data *pll;
+ unsigned long rate = clk->rate;
/* If this is the PLL base clock, no more calculations needed */
if (clk->pll_data)
- return;
+ return rate;
if (WARN_ON(!clk->parent))
- return;
+ return rate;
- clk->rate = clk->parent->rate;
+ rate = clk->parent->rate;
/* Otherwise, the parent must be a PLL */
if (WARN_ON(!clk->parent->pll_data))
- return;
+ return rate;
pll = clk->parent->pll_data;
/* If pre-PLL, source clock is before the multiplier and divider(s) */
if (clk->flags & PRE_PLL)
- clk->rate = pll->input_rate;
+ rate = pll->input_rate;
if (!clk->div_reg)
- return;
+ return rate;
v = __raw_readl(pll->base + clk->div_reg);
if (v & PLLDIV_EN) {
plldiv = (v & PLLDIV_RATIO_MASK) + 1;
if (plldiv)
- clk->rate /= plldiv;
+ rate /= plldiv;
}
+
+ return rate;
+}
+
+static unsigned long clk_leafclk_recalc(struct clk *clk)
+{
+ if (WARN_ON(!clk->parent))
+ return clk->rate;
+
+ return clk->parent->rate;
}
-static void __init clk_pll_init(struct clk *clk)
+static unsigned long clk_pllclk_recalc(struct clk *clk)
{
u32 ctrl, mult = 1, prediv = 1, postdiv = 1;
u8 bypass;
struct pll_data *pll = clk->pll_data;
+ unsigned long rate = clk->rate;
pll->base = IO_ADDRESS(pll->phys_base);
ctrl = __raw_readl(pll->base + PLLCTL);
- clk->rate = pll->input_rate = clk->parent->rate;
+ rate = pll->input_rate = clk->parent->rate;
if (ctrl & PLLCTL_PLLEN) {
bypass = 0;
}
if (!bypass) {
- clk->rate /= prediv;
- clk->rate *= mult;
- clk->rate /= postdiv;
+ rate /= prediv;
+ rate *= mult;
+ rate /= postdiv;
}
pr_debug("PLL%d: input = %lu MHz [ ",
pr_debug("* %d ", mult);
if (postdiv > 1)
pr_debug("/ %d ", postdiv);
- pr_debug("] --> %lu MHz output.\n", clk->rate / 1000000);
+ pr_debug("] --> %lu MHz output.\n", rate / 1000000);
+
+ return rate;
+}
+
+/**
+ * davinci_set_pllrate - set the output rate of a given PLL.
+ *
+ * Note: Currently tested to work with OMAP-L138 only.
+ *
+ * @pll: pll whose rate needs to be changed.
+ * @prediv: The pre divider value. Passing 0 disables the pre-divider.
+ * @pllm: The multiplier value. Passing 0 leads to multiply-by-one.
+ * @postdiv: The post divider value. Passing 0 disables the post-divider.
+ */
+int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv,
+ unsigned int mult, unsigned int postdiv)
+{
+ u32 ctrl;
+ unsigned int locktime;
+
+ if (pll->base == NULL)
+ return -EINVAL;
+
+ /*
+ * PLL lock time required per OMAP-L138 datasheet is
+ * (2000 * prediv)/sqrt(pllm) OSCIN cycles. We approximate sqrt(pllm)
+ * as 4 and OSCIN cycle as 25 MHz.
+ */
+ if (prediv) {
+ locktime = ((2000 * prediv) / 100);
+ prediv = (prediv - 1) | PLLDIV_EN;
+ } else {
+ locktime = 20;
+ }
+ if (postdiv)
+ postdiv = (postdiv - 1) | PLLDIV_EN;
+ if (mult)
+ mult = mult - 1;
+
+ ctrl = __raw_readl(pll->base + PLLCTL);
+
+ /* Switch the PLL to bypass mode */
+ ctrl &= ~(PLLCTL_PLLENSRC | PLLCTL_PLLEN);
+ __raw_writel(ctrl, pll->base + PLLCTL);
+
+ /*
+ * Wait for 4 OSCIN/CLKIN cycles to ensure that the PLLC has switched
+ * to bypass mode. Delay of 1us ensures we are good for all > 4MHz
+ * OSCIN/CLKIN inputs. Typically the input is ~25MHz.
+ */
+ udelay(1);
+
+ /* Reset and enable PLL */
+ ctrl &= ~(PLLCTL_PLLRST | PLLCTL_PLLDIS);
+ __raw_writel(ctrl, pll->base + PLLCTL);
+
+ if (pll->flags & PLL_HAS_PREDIV)
+ __raw_writel(prediv, pll->base + PREDIV);
+
+ __raw_writel(mult, pll->base + PLLM);
+
+ if (pll->flags & PLL_HAS_POSTDIV)
+ __raw_writel(postdiv, pll->base + POSTDIV);
+
+ /*
+ * Wait for PLL to reset properly, OMAP-L138 datasheet says
+ * 'min' time = 125ns
+ */
+ udelay(1);
+
+ /* Bring PLL out of reset */
+ ctrl |= PLLCTL_PLLRST;
+ __raw_writel(ctrl, pll->base + PLLCTL);
+
+ udelay(locktime);
+
+ /* Remove PLL from bypass mode */
+ ctrl |= PLLCTL_PLLEN;
+ __raw_writel(ctrl, pll->base + PLLCTL);
+
+ return 0;
}
+EXPORT_SYMBOL(davinci_set_pllrate);
int __init davinci_clk_init(struct davinci_clk *clocks)
{
for (c = clocks; c->lk.clk; c++) {
clk = c->lk.clk;
- if (clk->pll_data)
- clk_pll_init(clk);
+ if (!clk->recalc) {
+
+ /* Check if clock is a PLL */
+ if (clk->pll_data)
+ clk->recalc = clk_pllclk_recalc;
+
+ /* Else, if it is a PLL-derived clock */
+ else if (clk->flags & CLK_PLL)
+ clk->recalc = clk_sysclk_recalc;
+
+ /* Otherwise, it is a leaf clock (PSC clock) */
+ else if (clk->parent)
+ clk->recalc = clk_leafclk_recalc;
+ }
- /* Calculate rates for PLL-derived clocks */
- else if (clk->flags & CLK_PLL)
- clk_sysclk_recalc(clk);
+ if (clk->recalc)
+ clk->rate = clk->recalc(clk);
if (clk->lpsc)
clk->flags |= CLK_PSC;
/* REVISIT show device associations too */
/* cost is now small, but not linear... */
- list_for_each_entry(clk, &clocks, node) {
- if (clk->parent == parent)
- dump_clock(s, nest + NEST_DELTA, clk);
+ list_for_each_entry(clk, &parent->children, childnode) {
+ dump_clock(s, nest + NEST_DELTA, clk);
}
}
/* PLL/Reset register offsets */
#define PLLCTL 0x100
#define PLLCTL_PLLEN BIT(0)
+#define PLLCTL_PLLPWRDN BIT(1)
+#define PLLCTL_PLLRST BIT(3)
+#define PLLCTL_PLLDIS BIT(4)
+#define PLLCTL_PLLENSRC BIT(5)
#define PLLCTL_CLKMODE BIT(8)
#define PLLM 0x110
const char *name;
unsigned long rate;
u8 usecount;
- u8 flags;
u8 lpsc;
- u8 psc_ctlr;
+ u8 gpsc;
+ u32 flags;
struct clk *parent;
+ struct list_head children; /* list of children */
+ struct list_head childnode; /* parent's child list node */
struct pll_data *pll_data;
u32 div_reg;
+ unsigned long (*recalc) (struct clk *);
+ int (*set_rate) (struct clk *clk, unsigned long rate);
+ int (*round_rate) (struct clk *clk, unsigned long rate);
};
-/* Clock flags */
+/* Clock flags: SoC-specific flags start at BIT(16) */
#define ALWAYS_ENABLED BIT(1)
#define CLK_PSC BIT(2)
#define PSC_DSP BIT(3) /* PSC uses DSP domain, not ARM */
}
int davinci_clk_init(struct davinci_clk *clocks);
+int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv,
+ unsigned int mult, unsigned int postdiv);
extern struct platform_device davinci_wdt_device;
dip = davinci_get_id(davinci_soc_info.jtag_id);
if (!dip) {
ret = -EINVAL;
+ pr_err("Unknown DaVinci JTAG ID 0x%x\n",
+ davinci_soc_info.jtag_id);
goto err;
}
return;
err:
- pr_err("davinci_common_init: SoC Initialization failed\n");
+ panic("davinci_common_init: SoC Initialization failed\n");
}
*/
#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
#include <linux/irq.h>
#include <linux/io.h>
--- /dev/null
+/*
+ * CPU frequency scaling for DaVinci
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Based on linux/arch/arm/plat-omap/cpu-omap.c. Original Copyright follows:
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Written by Tony Lindgren <tony@atomide.com>
+ *
+ * Based on cpu-sa1110.c, Copyright (C) 2001 Russell King
+ *
+ * Copyright (C) 2007-2008 Texas Instruments, Inc.
+ * Updated to support OMAP3
+ * Rajendra Nayak <rnayak@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/types.h>
+#include <linux/cpufreq.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+
+#include <mach/hardware.h>
+#include <mach/cpufreq.h>
+#include <mach/common.h>
+
+#include "clock.h"
+
+struct davinci_cpufreq {
+ struct device *dev;
+ struct clk *armclk;
+};
+static struct davinci_cpufreq cpufreq;
+
+static int davinci_verify_speed(struct cpufreq_policy *policy)
+{
+ struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data;
+ struct cpufreq_frequency_table *freq_table = pdata->freq_table;
+ struct clk *armclk = cpufreq.armclk;
+
+ if (freq_table)
+ return cpufreq_frequency_table_verify(policy, freq_table);
+
+ if (policy->cpu)
+ return -EINVAL;
+
+ cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq,
+ policy->cpuinfo.max_freq);
+
+ policy->min = clk_round_rate(armclk, policy->min * 1000) / 1000;
+ policy->max = clk_round_rate(armclk, policy->max * 1000) / 1000;
+ cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq,
+ policy->cpuinfo.max_freq);
+ return 0;
+}
+
+static unsigned int davinci_getspeed(unsigned int cpu)
+{
+ if (cpu)
+ return 0;
+
+ return clk_get_rate(cpufreq.armclk) / 1000;
+}
+
+static int davinci_target(struct cpufreq_policy *policy,
+ unsigned int target_freq, unsigned int relation)
+{
+ int ret = 0;
+ unsigned int idx;
+ struct cpufreq_freqs freqs;
+ struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data;
+ struct clk *armclk = cpufreq.armclk;
+
+ /*
+ * Ensure desired rate is within allowed range. Some govenors
+ * (ondemand) will just pass target_freq=0 to get the minimum.
+ */
+ if (target_freq < policy->cpuinfo.min_freq)
+ target_freq = policy->cpuinfo.min_freq;
+ if (target_freq > policy->cpuinfo.max_freq)
+ target_freq = policy->cpuinfo.max_freq;
+
+ freqs.old = davinci_getspeed(0);
+ freqs.new = clk_round_rate(armclk, target_freq * 1000) / 1000;
+ freqs.cpu = 0;
+
+ if (freqs.old == freqs.new)
+ return ret;
+
+ cpufreq_debug_printk(CPUFREQ_DEBUG_DRIVER,
+ dev_driver_string(cpufreq.dev),
+ "transition: %u --> %u\n", freqs.old, freqs.new);
+
+ ret = cpufreq_frequency_table_target(policy, pdata->freq_table,
+ freqs.new, relation, &idx);
+ if (ret)
+ return -EINVAL;
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+
+ /* if moving to higher frequency, up the voltage beforehand */
+ if (pdata->set_voltage && freqs.new > freqs.old)
+ pdata->set_voltage(idx);
+
+ ret = clk_set_rate(armclk, idx);
+
+ /* if moving to lower freq, lower the voltage after lowering freq */
+ if (pdata->set_voltage && freqs.new < freqs.old)
+ pdata->set_voltage(idx);
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+ return ret;
+}
+
+static int __init davinci_cpu_init(struct cpufreq_policy *policy)
+{
+ int result = 0;
+ struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data;
+ struct cpufreq_frequency_table *freq_table = pdata->freq_table;
+
+ if (policy->cpu != 0)
+ return -EINVAL;
+
+ /* Finish platform specific initialization */
+ if (pdata->init) {
+ result = pdata->init();
+ if (result)
+ return result;
+ }
+
+ policy->cur = policy->min = policy->max = davinci_getspeed(0);
+
+ if (freq_table) {
+ result = cpufreq_frequency_table_cpuinfo(policy, freq_table);
+ if (!result)
+ cpufreq_frequency_table_get_attr(freq_table,
+ policy->cpu);
+ } else {
+ policy->cpuinfo.min_freq = policy->min;
+ policy->cpuinfo.max_freq = policy->max;
+ }
+
+ policy->min = policy->cpuinfo.min_freq;
+ policy->max = policy->cpuinfo.max_freq;
+ policy->cur = davinci_getspeed(0);
+
+ /*
+ * Time measurement across the target() function yields ~1500-1800us
+ * time taken with no drivers on notification list.
+ * Setting the latency to 2000 us to accomodate addition of drivers
+ * to pre/post change notification list.
+ */
+ policy->cpuinfo.transition_latency = 2000 * 1000;
+ return 0;
+}
+
+static int davinci_cpu_exit(struct cpufreq_policy *policy)
+{
+ cpufreq_frequency_table_put_attr(policy->cpu);
+ return 0;
+}
+
+static struct freq_attr *davinci_cpufreq_attr[] = {
+ &cpufreq_freq_attr_scaling_available_freqs,
+ NULL,
+};
+
+static struct cpufreq_driver davinci_driver = {
+ .flags = CPUFREQ_STICKY,
+ .verify = davinci_verify_speed,
+ .target = davinci_target,
+ .get = davinci_getspeed,
+ .init = davinci_cpu_init,
+ .exit = davinci_cpu_exit,
+ .name = "davinci",
+ .attr = davinci_cpufreq_attr,
+};
+
+static int __init davinci_cpufreq_probe(struct platform_device *pdev)
+{
+ struct davinci_cpufreq_config *pdata = pdev->dev.platform_data;
+
+ if (!pdata)
+ return -EINVAL;
+ if (!pdata->freq_table)
+ return -EINVAL;
+
+ cpufreq.dev = &pdev->dev;
+
+ cpufreq.armclk = clk_get(NULL, "arm");
+ if (IS_ERR(cpufreq.armclk)) {
+ dev_err(cpufreq.dev, "Unable to get ARM clock\n");
+ return PTR_ERR(cpufreq.armclk);
+ }
+
+ return cpufreq_register_driver(&davinci_driver);
+}
+
+static int __exit davinci_cpufreq_remove(struct platform_device *pdev)
+{
+ clk_put(cpufreq.armclk);
+
+ return cpufreq_unregister_driver(&davinci_driver);
+}
+
+static struct platform_driver davinci_cpufreq_driver = {
+ .driver = {
+ .name = "cpufreq-davinci",
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(davinci_cpufreq_remove),
+};
+
+static int __init davinci_cpufreq_init(void)
+{
+ return platform_driver_probe(&davinci_cpufreq_driver,
+ davinci_cpufreq_probe);
+}
+late_initcall(davinci_cpufreq_init);
+
--- /dev/null
+/*
+ * CPU idle for DaVinci SoCs
+ *
+ * Copyright (C) 2009 Texas Instruments Incorporated. http://www.ti.com/
+ *
+ * Derived from Marvell Kirkwood CPU idle code
+ * (arch/arm/mach-kirkwood/cpuidle.c)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/cpuidle.h>
+#include <linux/io.h>
+#include <asm/proc-fns.h>
+
+#include <mach/cpuidle.h>
+
+#define DAVINCI_CPUIDLE_MAX_STATES 2
+
+struct davinci_ops {
+ void (*enter) (u32 flags);
+ void (*exit) (u32 flags);
+ u32 flags;
+};
+
+/* fields in davinci_ops.flags */
+#define DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN BIT(0)
+
+static struct cpuidle_driver davinci_idle_driver = {
+ .name = "cpuidle-davinci",
+ .owner = THIS_MODULE,
+};
+
+static DEFINE_PER_CPU(struct cpuidle_device, davinci_cpuidle_device);
+static void __iomem *ddr2_reg_base;
+
+#define DDR2_SDRCR_OFFSET 0xc
+#define DDR2_SRPD_BIT BIT(23)
+#define DDR2_LPMODEN_BIT BIT(31)
+
+static void davinci_save_ddr_power(int enter, bool pdown)
+{
+ u32 val;
+
+ val = __raw_readl(ddr2_reg_base + DDR2_SDRCR_OFFSET);
+
+ if (enter) {
+ if (pdown)
+ val |= DDR2_SRPD_BIT;
+ else
+ val &= ~DDR2_SRPD_BIT;
+ val |= DDR2_LPMODEN_BIT;
+ } else {
+ val &= ~(DDR2_SRPD_BIT | DDR2_LPMODEN_BIT);
+ }
+
+ __raw_writel(val, ddr2_reg_base + DDR2_SDRCR_OFFSET);
+}
+
+static void davinci_c2state_enter(u32 flags)
+{
+ davinci_save_ddr_power(1, !!(flags & DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN));
+}
+
+static void davinci_c2state_exit(u32 flags)
+{
+ davinci_save_ddr_power(0, !!(flags & DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN));
+}
+
+static struct davinci_ops davinci_states[DAVINCI_CPUIDLE_MAX_STATES] = {
+ [1] = {
+ .enter = davinci_c2state_enter,
+ .exit = davinci_c2state_exit,
+ },
+};
+
+/* Actual code that puts the SoC in different idle states */
+static int davinci_enter_idle(struct cpuidle_device *dev,
+ struct cpuidle_state *state)
+{
+ struct davinci_ops *ops = cpuidle_get_statedata(state);
+ struct timeval before, after;
+ int idle_time;
+
+ local_irq_disable();
+ do_gettimeofday(&before);
+
+ if (ops && ops->enter)
+ ops->enter(ops->flags);
+ /* Wait for interrupt state */
+ cpu_do_idle();
+ if (ops && ops->exit)
+ ops->exit(ops->flags);
+
+ do_gettimeofday(&after);
+ local_irq_enable();
+ idle_time = (after.tv_sec - before.tv_sec) * USEC_PER_SEC +
+ (after.tv_usec - before.tv_usec);
+ return idle_time;
+}
+
+static int __init davinci_cpuidle_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct cpuidle_device *device;
+ struct davinci_cpuidle_config *pdata = pdev->dev.platform_data;
+ struct resource *ddr2_regs;
+ resource_size_t len;
+
+ device = &per_cpu(davinci_cpuidle_device, smp_processor_id());
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "cannot get platform data\n");
+ return -ENOENT;
+ }
+
+ ddr2_regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!ddr2_regs) {
+ dev_err(&pdev->dev, "cannot get DDR2 controller register base");
+ return -ENODEV;
+ }
+
+ len = resource_size(ddr2_regs);
+
+ ddr2_regs = request_mem_region(ddr2_regs->start, len, ddr2_regs->name);
+ if (!ddr2_regs)
+ return -EBUSY;
+
+ ddr2_reg_base = ioremap(ddr2_regs->start, len);
+ if (!ddr2_reg_base) {
+ ret = -ENOMEM;
+ goto ioremap_fail;
+ }
+
+ ret = cpuidle_register_driver(&davinci_idle_driver);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register driver\n");
+ goto driver_register_fail;
+ }
+
+ /* Wait for interrupt state */
+ device->states[0].enter = davinci_enter_idle;
+ device->states[0].exit_latency = 1;
+ device->states[0].target_residency = 10000;
+ device->states[0].flags = CPUIDLE_FLAG_TIME_VALID;
+ strcpy(device->states[0].name, "WFI");
+ strcpy(device->states[0].desc, "Wait for interrupt");
+
+ /* Wait for interrupt and DDR self refresh state */
+ device->states[1].enter = davinci_enter_idle;
+ device->states[1].exit_latency = 10;
+ device->states[1].target_residency = 10000;
+ device->states[1].flags = CPUIDLE_FLAG_TIME_VALID;
+ strcpy(device->states[1].name, "DDR SR");
+ strcpy(device->states[1].desc, "WFI and DDR Self Refresh");
+ if (pdata->ddr2_pdown)
+ davinci_states[1].flags |= DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN;
+ cpuidle_set_statedata(&device->states[1], &davinci_states[1]);
+
+ device->state_count = DAVINCI_CPUIDLE_MAX_STATES;
+
+ ret = cpuidle_register_device(device);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register device\n");
+ goto device_register_fail;
+ }
+
+ return 0;
+
+device_register_fail:
+ cpuidle_unregister_driver(&davinci_idle_driver);
+driver_register_fail:
+ iounmap(ddr2_reg_base);
+ioremap_fail:
+ release_mem_region(ddr2_regs->start, len);
+ return ret;
+}
+
+static struct platform_driver davinci_cpuidle_driver = {
+ .driver = {
+ .name = "cpuidle-davinci",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init davinci_cpuidle_init(void)
+{
+ return platform_driver_probe(&davinci_cpuidle_driver,
+ davinci_cpuidle_probe);
+}
+device_initcall(davinci_cpuidle_init);
+
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
-#include <linux/platform_device.h>
#include <asm/mach/map.h>
-#include <mach/clock.h>
#include <mach/psc.h>
-#include <mach/mux.h>
#include <mach/irqs.h>
#include <mach/cputype.h>
#include <mach/common.h>
#include <mach/time.h>
#include <mach/da8xx.h>
-#include <mach/asp.h>
#include "clock.h"
#include "mux.h"
.name = "uart1",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_UART1,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk uart2_clk = {
.name = "uart2",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_UART2,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk spi0_clk = {
.name = "spi1",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_SPI1,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk ecap0_clk = {
.name = "ecap0",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_ECAP,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk ecap1_clk = {
.name = "ecap1",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_ECAP,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk ecap2_clk = {
.name = "ecap2",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_ECAP,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk pwm0_clk = {
.name = "pwm0",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_PWM,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk pwm1_clk = {
.name = "pwm1",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_PWM,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk pwm2_clk = {
.name = "pwm2",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_PWM,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk eqep0_clk = {
.name = "eqep0",
.parent = &pll0_sysclk2,
.lpsc = DA830_LPSC1_EQEP,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk eqep1_clk = {
.name = "eqep1",
.parent = &pll0_sysclk2,
.lpsc = DA830_LPSC1_EQEP,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk lcdc_clk = {
.name = "lcdc",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_LCDC,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk mcasp0_clk = {
.name = "mcasp0",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_McASP0,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk mcasp1_clk = {
.name = "mcasp1",
.parent = &pll0_sysclk2,
.lpsc = DA830_LPSC1_McASP1,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk mcasp2_clk = {
.name = "mcasp2",
.parent = &pll0_sysclk2,
.lpsc = DA830_LPSC1_McASP2,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk usb20_clk = {
.name = "usb20",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_USB20,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk aemif_clk = {
.name = "emac",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_CPGMAC,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk gpio_clk = {
.name = "gpio",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_GPIO,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk i2c1_clk = {
.name = "i2c1",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_I2C,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk usb11_clk = {
.name = "usb11",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_USB11,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk emif3_clk = {
.name = "emif3",
.parent = &pll0_sysclk5,
.lpsc = DA8XX_LPSC1_EMIF3C,
+ .gpsc = 1,
.flags = ALWAYS_ENABLED,
- .psc_ctlr = 1,
};
static struct clk arm_clk = {
CLK(NULL, "pwm2", &pwm2_clk),
CLK("eqep.0", NULL, &eqep0_clk),
CLK("eqep.1", NULL, &eqep1_clk),
- CLK("da830_lcdc", NULL, &lcdc_clk),
+ CLK("da8xx_lcdc.0", NULL, &lcdc_clk),
CLK("davinci-mcasp.0", NULL, &mcasp0_clk),
CLK("davinci-mcasp.1", NULL, &mcasp1_clk),
CLK("davinci-mcasp.2", NULL, &mcasp2_clk),
.part_no = 0xb7df,
.manufacturer = 0x017, /* 0x02f >> 1 */
.cpu_id = DAVINCI_CPU_ID_DA830,
- .name = "da830/omap l137",
+ .name = "da830/omap-l137 rev1.0",
+ },
+ {
+ .variant = 0x8,
+ .part_no = 0xb7df,
+ .manufacturer = 0x017,
+ .cpu_id = DAVINCI_CPU_ID_DA830,
+ .name = "da830/omap-l137 rev1.1",
+ },
+ {
+ .variant = 0x9,
+ .part_no = 0xb7df,
+ .manufacturer = 0x017,
+ .cpu_id = DAVINCI_CPU_ID_DA830,
+ .name = "da830/omap-l137 rev2.0",
},
};
static struct davinci_soc_info davinci_soc_info_da830 = {
.io_desc = da830_io_desc,
.io_desc_num = ARRAY_SIZE(da830_io_desc),
- .jtag_id_base = IO_ADDRESS(DA8XX_JTAG_ID_REG),
.ids = da830_ids,
.ids_num = ARRAY_SIZE(da830_ids),
.cpu_clks = da830_clks,
.psc_bases = da830_psc_bases,
.psc_bases_num = ARRAY_SIZE(da830_psc_bases),
- .pinmux_base = IO_ADDRESS(DA8XX_BOOT_CFG_BASE + 0x120),
.pinmux_pins = da830_pins,
.pinmux_pins_num = ARRAY_SIZE(da830_pins),
.intc_base = (void __iomem *)DA8XX_CP_INTC_VIRT,
void __init da830_init(void)
{
+ da8xx_syscfg_base = ioremap(DA8XX_SYSCFG_BASE, SZ_4K);
+ if (WARN(!da8xx_syscfg_base, "Unable to map syscfg module"))
+ return;
+
+ davinci_soc_info_da830.jtag_id_base =
+ DA8XX_SYSCFG_VIRT(DA8XX_JTAG_ID_REG);
+ davinci_soc_info_da830.pinmux_base = DA8XX_SYSCFG_VIRT(0x120);
+
davinci_common_init(&davinci_soc_info_da830);
}
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
+#include <linux/cpufreq.h>
+#include <linux/regulator/consumer.h>
#include <asm/mach/map.h>
-#include <mach/clock.h>
#include <mach/psc.h>
-#include <mach/mux.h>
#include <mach/irqs.h>
#include <mach/cputype.h>
#include <mach/common.h>
#include <mach/time.h>
#include <mach/da8xx.h>
+#include <mach/cpufreq.h>
#include "clock.h"
#include "mux.h"
+/* SoC specific clock flags */
+#define DA850_CLK_ASYNC3 BIT(16)
+
#define DA850_PLL1_BASE 0x01e1a000
#define DA850_TIMER64P2_BASE 0x01f0c000
#define DA850_TIMER64P3_BASE 0x01f0d000
#define DA850_REF_FREQ 24000000
+#define CFGCHIP3_ASYNC3_CLKSRC BIT(4)
+#define CFGCHIP0_PLL_MASTER_LOCK BIT(4)
+
+static int da850_set_armrate(struct clk *clk, unsigned long rate);
+static int da850_round_armrate(struct clk *clk, unsigned long rate);
+static int da850_set_pll0rate(struct clk *clk, unsigned long armrate);
+
static struct pll_data pll0_data = {
.num = 1,
.phys_base = DA8XX_PLL0_BASE,
.parent = &ref_clk,
.pll_data = &pll0_data,
.flags = CLK_PLL,
+ .set_rate = da850_set_pll0rate,
};
static struct clk pll0_aux_clk = {
.name = "tpcc1",
.parent = &pll0_sysclk2,
.lpsc = DA850_LPSC1_TPCC1,
+ .gpsc = 1,
.flags = CLK_PSC | ALWAYS_ENABLED,
- .psc_ctlr = 1,
};
static struct clk tptc2_clk = {
.name = "tptc2",
.parent = &pll0_sysclk2,
.lpsc = DA850_LPSC1_TPTC2,
+ .gpsc = 1,
.flags = ALWAYS_ENABLED,
- .psc_ctlr = 1,
};
static struct clk uart0_clk = {
.name = "uart1",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_UART1,
- .psc_ctlr = 1,
+ .gpsc = 1,
+ .flags = DA850_CLK_ASYNC3,
};
static struct clk uart2_clk = {
.name = "uart2",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_UART2,
- .psc_ctlr = 1,
+ .gpsc = 1,
+ .flags = DA850_CLK_ASYNC3,
};
static struct clk aintc_clk = {
.name = "gpio",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_GPIO,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk i2c1_clk = {
.name = "i2c1",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_I2C,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk emif3_clk = {
.name = "emif3",
.parent = &pll0_sysclk5,
.lpsc = DA8XX_LPSC1_EMIF3C,
+ .gpsc = 1,
.flags = ALWAYS_ENABLED,
- .psc_ctlr = 1,
};
static struct clk arm_clk = {
.parent = &pll0_sysclk6,
.lpsc = DA8XX_LPSC0_ARM,
.flags = ALWAYS_ENABLED,
+ .set_rate = da850_set_armrate,
+ .round_rate = da850_round_armrate,
};
static struct clk rmii_clk = {
.name = "emac",
.parent = &pll0_sysclk4,
.lpsc = DA8XX_LPSC1_CPGMAC,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk mcasp_clk = {
.name = "mcasp",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_McASP0,
- .psc_ctlr = 1,
+ .gpsc = 1,
+ .flags = DA850_CLK_ASYNC3,
};
static struct clk lcdc_clk = {
.name = "lcdc",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC1_LCDC,
- .psc_ctlr = 1,
+ .gpsc = 1,
};
static struct clk mmcsd_clk = {
MUX_CFG(DA850, MII_RXD_0, 3, 28, 15, 8, false)
MUX_CFG(DA850, MDIO_CLK, 4, 0, 15, 8, false)
MUX_CFG(DA850, MDIO_D, 4, 4, 15, 8, false)
+ MUX_CFG(DA850, RMII_TXD_0, 14, 12, 15, 8, false)
+ MUX_CFG(DA850, RMII_TXD_1, 14, 8, 15, 8, false)
+ MUX_CFG(DA850, RMII_TXEN, 14, 16, 15, 8, false)
+ MUX_CFG(DA850, RMII_CRS_DV, 15, 4, 15, 8, false)
+ MUX_CFG(DA850, RMII_RXD_0, 14, 24, 15, 8, false)
+ MUX_CFG(DA850, RMII_RXD_1, 14, 20, 15, 8, false)
+ MUX_CFG(DA850, RMII_RXER, 14, 28, 15, 8, false)
+ MUX_CFG(DA850, RMII_MHZ_50_CLK, 15, 0, 15, 0, false)
/* McASP function */
MUX_CFG(DA850, ACLKR, 0, 0, 15, 1, false)
MUX_CFG(DA850, ACLKX, 0, 4, 15, 1, false)
MUX_CFG(DA850, EMA_WAIT_1, 6, 24, 15, 1, false)
MUX_CFG(DA850, NEMA_CS_2, 7, 0, 15, 1, false)
/* GPIO function */
+ MUX_CFG(DA850, GPIO2_6, 6, 4, 15, 8, false)
+ MUX_CFG(DA850, GPIO2_8, 5, 28, 15, 8, false)
MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false)
- MUX_CFG(DA850, GPIO8_10, 18, 28, 15, 8, false)
MUX_CFG(DA850, GPIO4_0, 10, 28, 15, 8, false)
MUX_CFG(DA850, GPIO4_1, 10, 24, 15, 8, false)
#endif
-1
};
+const short da850_rmii_pins[] __initdata = {
+ DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
+ DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
+ DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
+ DA850_MDIO_D,
+ -1
+};
+
const short da850_mcasp_pins[] __initdata = {
DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
};
const short da850_lcdcntl_pins[] __initdata = {
- DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3, DA850_LCD_D_4,
- DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7, DA850_LCD_D_8,
- DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11, DA850_LCD_D_12,
- DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15, DA850_LCD_PCLK,
- DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS, DA850_GPIO2_15,
- DA850_GPIO8_10,
+ DA850_LCD_D_0, DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3,
+ DA850_LCD_D_4, DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7,
+ DA850_LCD_D_8, DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11,
+ DA850_LCD_D_12, DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15,
+ DA850_LCD_PCLK, DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS,
-1
};
.clocksource_id = T0_TOP,
};
+static void da850_set_async3_src(int pllnum)
+{
+ struct clk *clk, *newparent = pllnum ? &pll1_sysclk2 : &pll0_sysclk2;
+ struct davinci_clk *c;
+ unsigned int v;
+ int ret;
+
+ for (c = da850_clks; c->lk.clk; c++) {
+ clk = c->lk.clk;
+ if (clk->flags & DA850_CLK_ASYNC3) {
+ ret = clk_set_parent(clk, newparent);
+ WARN(ret, "DA850: unable to re-parent clock %s",
+ clk->name);
+ }
+ }
+
+ v = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP3_REG));
+ if (pllnum)
+ v |= CFGCHIP3_ASYNC3_CLKSRC;
+ else
+ v &= ~CFGCHIP3_ASYNC3_CLKSRC;
+ __raw_writel(v, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP3_REG));
+}
+
+#ifdef CONFIG_CPU_FREQ
+/*
+ * Notes:
+ * According to the TRM, minimum PLLM results in maximum power savings.
+ * The OPP definitions below should keep the PLLM as low as possible.
+ *
+ * The output of the PLLM must be between 400 to 600 MHz.
+ * This rules out prediv of anything but divide-by-one for 24Mhz OSC input.
+ */
+struct da850_opp {
+ unsigned int freq; /* in KHz */
+ unsigned int prediv;
+ unsigned int mult;
+ unsigned int postdiv;
+ unsigned int cvdd_min; /* in uV */
+ unsigned int cvdd_max; /* in uV */
+};
+
+static const struct da850_opp da850_opp_300 = {
+ .freq = 300000,
+ .prediv = 1,
+ .mult = 25,
+ .postdiv = 2,
+ .cvdd_min = 1140000,
+ .cvdd_max = 1320000,
+};
+
+static const struct da850_opp da850_opp_200 = {
+ .freq = 200000,
+ .prediv = 1,
+ .mult = 25,
+ .postdiv = 3,
+ .cvdd_min = 1050000,
+ .cvdd_max = 1160000,
+};
+
+static const struct da850_opp da850_opp_96 = {
+ .freq = 96000,
+ .prediv = 1,
+ .mult = 20,
+ .postdiv = 5,
+ .cvdd_min = 950000,
+ .cvdd_max = 1050000,
+};
+
+#define OPP(freq) \
+ { \
+ .index = (unsigned int) &da850_opp_##freq, \
+ .frequency = freq * 1000, \
+ }
+
+static struct cpufreq_frequency_table da850_freq_table[] = {
+ OPP(300),
+ OPP(200),
+ OPP(96),
+ {
+ .index = 0,
+ .frequency = CPUFREQ_TABLE_END,
+ },
+};
+
+#ifdef CONFIG_REGULATOR
+static struct regulator *cvdd;
+
+static int da850_set_voltage(unsigned int index)
+{
+ struct da850_opp *opp;
+
+ if (!cvdd)
+ return -ENODEV;
+
+ opp = (struct da850_opp *) da850_freq_table[index].index;
+
+ return regulator_set_voltage(cvdd, opp->cvdd_min, opp->cvdd_max);
+}
+
+static int da850_regulator_init(void)
+{
+ cvdd = regulator_get(NULL, "cvdd");
+ if (WARN(IS_ERR(cvdd), "Unable to obtain voltage regulator for CVDD;"
+ " voltage scaling unsupported\n")) {
+ return PTR_ERR(cvdd);
+ }
+
+ return 0;
+}
+#endif
+
+static struct davinci_cpufreq_config cpufreq_info = {
+ .freq_table = &da850_freq_table[0],
+#ifdef CONFIG_REGULATOR
+ .init = da850_regulator_init,
+ .set_voltage = da850_set_voltage,
+#endif
+};
+
+static struct platform_device da850_cpufreq_device = {
+ .name = "cpufreq-davinci",
+ .dev = {
+ .platform_data = &cpufreq_info,
+ },
+};
+
+int __init da850_register_cpufreq(void)
+{
+ return platform_device_register(&da850_cpufreq_device);
+}
+
+static int da850_round_armrate(struct clk *clk, unsigned long rate)
+{
+ int i, ret = 0, diff;
+ unsigned int best = (unsigned int) -1;
+
+ rate /= 1000; /* convert to kHz */
+
+ for (i = 0; da850_freq_table[i].frequency != CPUFREQ_TABLE_END; i++) {
+ diff = da850_freq_table[i].frequency - rate;
+ if (diff < 0)
+ diff = -diff;
+
+ if (diff < best) {
+ best = diff;
+ ret = da850_freq_table[i].frequency;
+ }
+ }
+
+ return ret * 1000;
+}
+
+static int da850_set_armrate(struct clk *clk, unsigned long index)
+{
+ struct clk *pllclk = &pll0_clk;
+
+ return clk_set_rate(pllclk, index);
+}
+
+static int da850_set_pll0rate(struct clk *clk, unsigned long index)
+{
+ unsigned int prediv, mult, postdiv;
+ struct da850_opp *opp;
+ struct pll_data *pll = clk->pll_data;
+ unsigned int v;
+ int ret;
+
+ opp = (struct da850_opp *) da850_freq_table[index].index;
+ prediv = opp->prediv;
+ mult = opp->mult;
+ postdiv = opp->postdiv;
+
+ /* Unlock writing to PLL registers */
+ v = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP0_REG));
+ v &= ~CFGCHIP0_PLL_MASTER_LOCK;
+ __raw_writel(v, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP0_REG));
+
+ ret = davinci_set_pllrate(pll, prediv, mult, postdiv);
+ if (WARN_ON(ret))
+ return ret;
+
+ return 0;
+}
+#else
+int __init da850_register_cpufreq(void)
+{
+ return 0;
+}
+
+static int da850_set_armrate(struct clk *clk, unsigned long rate)
+{
+ return -EINVAL;
+}
+
+static int da850_set_pll0rate(struct clk *clk, unsigned long armrate)
+{
+ return -EINVAL;
+}
+
+static int da850_round_armrate(struct clk *clk, unsigned long rate)
+{
+ return clk->rate;
+}
+#endif
+
+
static struct davinci_soc_info davinci_soc_info_da850 = {
.io_desc = da850_io_desc,
.io_desc_num = ARRAY_SIZE(da850_io_desc),
- .jtag_id_base = IO_ADDRESS(DA8XX_JTAG_ID_REG),
.ids = da850_ids,
.ids_num = ARRAY_SIZE(da850_ids),
.cpu_clks = da850_clks,
.psc_bases = da850_psc_bases,
.psc_bases_num = ARRAY_SIZE(da850_psc_bases),
- .pinmux_base = IO_ADDRESS(DA8XX_BOOT_CFG_BASE + 0x120),
.pinmux_pins = da850_pins,
.pinmux_pins_num = ARRAY_SIZE(da850_pins),
.intc_base = (void __iomem *)DA8XX_CP_INTC_VIRT,
void __init da850_init(void)
{
+ da8xx_syscfg_base = ioremap(DA8XX_SYSCFG_BASE, SZ_4K);
+ if (WARN(!da8xx_syscfg_base, "Unable to map syscfg module"))
+ return;
+
+ davinci_soc_info_da850.jtag_id_base =
+ DA8XX_SYSCFG_VIRT(DA8XX_JTAG_ID_REG);
+ davinci_soc_info_da850.pinmux_base = DA8XX_SYSCFG_VIRT(0x120);
+
davinci_common_init(&davinci_soc_info_da850);
+
+ /*
+ * Move the clock source of Async3 domain to PLL1 SYSCLK2.
+ * This helps keeping the peripherals on this domain insulated
+ * from CPU frequency changes caused by DVFS. The firmware sets
+ * both PLL0 and PLL1 to the same frequency so, there should not
+ * be any noticible change even in non-DVFS use cases.
+ */
+ da850_set_async3_src(1);
}
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <mach/common.h>
#include <mach/time.h>
#include <mach/da8xx.h>
-#include <video/da8xx-fb.h>
+#include <mach/cpuidle.h>
#include "clock.h"
#define DA8XX_TPTC1_BASE 0x01c08400
#define DA8XX_WDOG_BASE 0x01c21000 /* DA8XX_TIMER64P1_BASE */
#define DA8XX_I2C0_BASE 0x01c22000
+#define DA8XX_RTC_BASE 0x01C23000
#define DA8XX_EMAC_CPPI_PORT_BASE 0x01e20000
#define DA8XX_EMAC_CPGMACSS_BASE 0x01e22000
#define DA8XX_EMAC_CPGMAC_BASE 0x01e23000
#define DA8XX_MDIO_REG_OFFSET 0x4000
#define DA8XX_EMAC_CTRL_RAM_SIZE SZ_8K
+void __iomem *da8xx_syscfg_base;
+
static struct plat_serial8250_port da8xx_serial_pdata[] = {
{
.mapbase = DA8XX_UART0_BASE,
.resource = da8xx_emac_resources,
};
+int __init da8xx_register_emac(void)
+{
+ return platform_device_register(&da8xx_emac_device);
+}
+
static struct resource da830_mcasp1_resources[] = {
{
.name = "mcasp1",
.resource = da850_mcasp_resources,
};
-int __init da8xx_register_emac(void)
-{
- return platform_device_register(&da8xx_emac_device);
-}
-
-void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata)
+void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata)
{
/* DA830/OMAP-L137 has 3 instances of McASP */
if (cpu_is_davinci_da830() && id == 1) {
.raster_order = 0,
};
-static struct da8xx_lcdc_platform_data da850_evm_lcdc_pdata = {
- .manu_name = "sharp",
- .controller_data = &lcd_cfg,
- .type = "Sharp_LK043T1DG01",
+struct da8xx_lcdc_platform_data sharp_lcd035q3dg01_pdata = {
+ .manu_name = "sharp",
+ .controller_data = &lcd_cfg,
+ .type = "Sharp_LCD035Q3DG01",
+};
+
+struct da8xx_lcdc_platform_data sharp_lk043t1dg01_pdata = {
+ .manu_name = "sharp",
+ .controller_data = &lcd_cfg,
+ .type = "Sharp_LK043T1DG01",
};
static struct resource da8xx_lcdc_resources[] = {
},
};
-static struct platform_device da850_lcdc_device = {
+static struct platform_device da8xx_lcdc_device = {
.name = "da8xx_lcdc",
.id = 0,
.num_resources = ARRAY_SIZE(da8xx_lcdc_resources),
.resource = da8xx_lcdc_resources,
- .dev = {
- .platform_data = &da850_evm_lcdc_pdata,
- }
};
-int __init da8xx_register_lcdc(void)
+int __init da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata)
{
- return platform_device_register(&da850_lcdc_device);
+ da8xx_lcdc_device.dev.platform_data = pdata;
+ return platform_device_register(&da8xx_lcdc_device);
}
static struct resource da8xx_mmcsd0_resources[] = {
da8xx_mmcsd0_device.dev.platform_data = config;
return platform_device_register(&da8xx_mmcsd0_device);
}
+
+static struct resource da8xx_rtc_resources[] = {
+ {
+ .start = DA8XX_RTC_BASE,
+ .end = DA8XX_RTC_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* timer irq */
+ .start = IRQ_DA8XX_RTC,
+ .end = IRQ_DA8XX_RTC,
+ .flags = IORESOURCE_IRQ,
+ },
+ { /* alarm irq */
+ .start = IRQ_DA8XX_RTC,
+ .end = IRQ_DA8XX_RTC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device da8xx_rtc_device = {
+ .name = "omap_rtc",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(da8xx_rtc_resources),
+ .resource = da8xx_rtc_resources,
+};
+
+int da8xx_register_rtc(void)
+{
+ /* Unlock the rtc's registers */
+ __raw_writel(0x83e70b13, IO_ADDRESS(DA8XX_RTC_BASE + 0x6c));
+ __raw_writel(0x95a4f1e0, IO_ADDRESS(DA8XX_RTC_BASE + 0x70));
+
+ return platform_device_register(&da8xx_rtc_device);
+}
+
+static struct resource da8xx_cpuidle_resources[] = {
+ {
+ .start = DA8XX_DDR2_CTL_BASE,
+ .end = DA8XX_DDR2_CTL_BASE + SZ_32K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+/* DA8XX devices support DDR2 power down */
+static struct davinci_cpuidle_config da8xx_cpuidle_pdata = {
+ .ddr2_pdown = 1,
+};
+
+
+static struct platform_device da8xx_cpuidle_device = {
+ .name = "cpuidle-davinci",
+ .num_resources = ARRAY_SIZE(da8xx_cpuidle_resources),
+ .resource = da8xx_cpuidle_resources,
+ .dev = {
+ .platform_data = &da8xx_cpuidle_pdata,
+ },
+};
+
+int __init da8xx_register_cpuidle(void)
+{
+ return platform_device_register(&da8xx_cpuidle_device);
+}
+
* (at your option) any later version.
*/
-#include <linux/module.h>
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
-#include <asm/mach/map.h>
-
#include <mach/hardware.h>
#include <mach/i2c.h>
#include <mach/irqs.h>
mmcsd1_resources[0].start = DM365_MMCSD1_BASE;
mmcsd1_resources[0].end = DM365_MMCSD1_BASE +
SZ_4K - 1;
- mmcsd0_resources[2].start = IRQ_DM365_SDIOINT1;
+ mmcsd1_resources[2].start = IRQ_DM365_SDIOINT1;
} else
break;
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <asm/mach/map.h>
#include <mach/dm355.h>
-#include <mach/clock.h>
#include <mach/cputype.h>
#include <mach/edma.h>
#include <mach/psc.h>
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <asm/mach/map.h>
#include <mach/dm365.h>
-#include <mach/clock.h>
#include <mach/cputype.h>
#include <mach/edma.h>
#include <mach/psc.h>
#include <mach/time.h>
#include <mach/serial.h>
#include <mach/common.h>
+#include <mach/asp.h>
+#include <mach/keyscan.h>
#include "clock.h"
#include "mux.h"
static struct clk usb_clk = {
.name = "usb",
- .parent = &pll2_sysclk1,
+ .parent = &pll1_aux_clk,
.lpsc = DAVINCI_LPSC_USB,
};
CLK(NULL, "usb", &usb_clk),
CLK("davinci_emac.1", NULL, &emac_clk),
CLK("voice_codec", NULL, &voicecodec_clk),
- CLK("soc-audio.0", NULL, &asp0_clk),
+ CLK("davinci-asp.0", NULL, &asp0_clk),
CLK(NULL, "rto", &rto_clk),
CLK(NULL, "mjcp", &mjcp_clk),
CLK(NULL, NULL, NULL),
MUX_CFG(DM365, EMAC_MDIO, 3, 1, 1, 1, false)
MUX_CFG(DM365, EMAC_MDCLK, 3, 0, 1, 1, false)
-MUX_CFG(DM365, KEYPAD, 2, 0, 0x3f, 0x3f, false)
+MUX_CFG(DM365, KEYSCAN, 2, 0, 0x3f, 0x3f, false)
MUX_CFG(DM365, PWM0, 1, 0, 3, 2, false)
MUX_CFG(DM365, PWM0_G23, 3, 26, 3, 3, false)
INT_CFG(DM365, INT_IMX1_DISABLE, 24, 1, 0, false)
INT_CFG(DM365, INT_NSF_ENABLE, 25, 1, 1, false)
INT_CFG(DM365, INT_NSF_DISABLE, 25, 1, 0, false)
+
+EVT_CFG(DM365, EVT2_ASP_TX, 0, 1, 0, false)
+EVT_CFG(DM365, EVT3_ASP_RX, 1, 1, 0, false)
#endif
};
[IRQ_I2C] = 3,
[IRQ_UARTINT0] = 3,
[IRQ_UARTINT1] = 3,
+ [IRQ_DM365_RTCINT] = 3,
[IRQ_DM365_SPIINT0_0] = 3,
[IRQ_DM365_SPIINT3_0] = 3,
[IRQ_DM365_GPIO0] = 3,
.resource = edma_resources,
};
+static struct resource dm365_asp_resources[] = {
+ {
+ .start = DAVINCI_DM365_ASP0_BASE,
+ .end = DAVINCI_DM365_ASP0_BASE + SZ_8K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = DAVINCI_DMA_ASP0_TX,
+ .end = DAVINCI_DMA_ASP0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = DAVINCI_DMA_ASP0_RX,
+ .end = DAVINCI_DMA_ASP0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device dm365_asp_device = {
+ .name = "davinci-asp",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(dm365_asp_resources),
+ .resource = dm365_asp_resources,
+};
+
+static struct resource dm365_rtc_resources[] = {
+ {
+ .start = DM365_RTC_BASE,
+ .end = DM365_RTC_BASE + SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_DM365_RTCINT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device dm365_rtc_device = {
+ .name = "rtc_davinci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(dm365_rtc_resources),
+ .resource = dm365_rtc_resources,
+};
+
static struct map_desc dm365_io_desc[] = {
{
.virtual = IO_VIRT,
},
};
+static struct resource dm365_ks_resources[] = {
+ {
+ /* registers */
+ .start = DM365_KEYSCAN_BASE,
+ .end = DM365_KEYSCAN_BASE + SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ /* interrupt */
+ .start = IRQ_DM365_KEYINT,
+ .end = IRQ_DM365_KEYINT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device dm365_ks_device = {
+ .name = "davinci_keyscan",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(dm365_ks_resources),
+ .resource = dm365_ks_resources,
+};
+
/* Contents of JTAG ID register used to identify exact cpu type */
static struct davinci_id dm365_ids[] = {
{
.sram_len = SZ_32K,
};
+void __init dm365_init_asp(struct snd_platform_data *pdata)
+{
+ davinci_cfg_reg(DM365_MCBSP0_BDX);
+ davinci_cfg_reg(DM365_MCBSP0_X);
+ davinci_cfg_reg(DM365_MCBSP0_BFSX);
+ davinci_cfg_reg(DM365_MCBSP0_BDR);
+ davinci_cfg_reg(DM365_MCBSP0_R);
+ davinci_cfg_reg(DM365_MCBSP0_BFSR);
+ davinci_cfg_reg(DM365_EVT2_ASP_TX);
+ davinci_cfg_reg(DM365_EVT3_ASP_RX);
+ dm365_asp_device.dev.platform_data = pdata;
+ platform_device_register(&dm365_asp_device);
+}
+
+void __init dm365_init_ks(struct davinci_ks_platform_data *pdata)
+{
+ davinci_cfg_reg(DM365_KEYSCAN);
+ dm365_ks_device.dev.platform_data = pdata;
+ platform_device_register(&dm365_ks_device);
+}
+
+void __init dm365_init_rtc(void)
+{
+ davinci_cfg_reg(DM365_INT_PRTCSS);
+ platform_device_register(&dm365_rtc_device);
+}
+
void __init dm365_init(void)
{
davinci_common_init(&davinci_soc_info_dm365);
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <asm/mach/map.h>
#include <mach/dm644x.h>
-#include <mach/clock.h>
#include <mach/cputype.h>
#include <mach/edma.h>
#include <mach/irqs.h>
MUX_CFG(DM644X, HPIEN_DISABLE, 0, 29, 1, 0, true)
MUX_CFG(DM644X, AEAW, 0, 0, 31, 31, true)
+MUX_CFG(DM644X, AEAW0, 0, 0, 1, 0, true)
+MUX_CFG(DM644X, AEAW1, 0, 1, 1, 0, true)
+MUX_CFG(DM644X, AEAW2, 0, 2, 1, 0, true)
+MUX_CFG(DM644X, AEAW3, 0, 3, 1, 0, true)
+MUX_CFG(DM644X, AEAW4, 0, 4, 1, 0, true)
MUX_CFG(DM644X, MSTK, 1, 9, 1, 0, false)
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/serial_8250.h>
#include <asm/mach/map.h>
#include <mach/dm646x.h>
-#include <mach/clock.h>
#include <mach/cputype.h>
#include <mach/edma.h>
#include <mach/irqs.h>
.part_no = 0xb770,
.manufacturer = 0x017,
.cpu_id = DAVINCI_CPU_ID_DM6467,
- .name = "dm6467",
+ .name = "dm6467_rev1.x",
+ },
+ {
+ .variant = 0x1,
+ .part_no = 0xb770,
+ .manufacturer = 0x017,
+ .cpu_id = DAVINCI_CPU_ID_DM6467,
+ .name = "dm6467_rev3.x",
},
};
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
-#include <linux/sched.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
-#include <linux/spinlock.h>
-#include <linux/compiler.h>
#include <linux/io.h>
-#include <mach/cputype.h>
-#include <mach/memory.h>
-#include <mach/hardware.h>
-#include <mach/irqs.h>
#include <mach/edma.h>
-#include <mach/mux.h>
-
/* Offsets matching "struct edmacc_param" */
#define PARM_OPT 0x00
return IRQ_HANDLED;
}
-static int reserve_contiguous_params(int ctlr, unsigned int id,
- unsigned int num_params,
- unsigned int start_param)
+static int reserve_contiguous_slots(int ctlr, unsigned int id,
+ unsigned int num_slots,
+ unsigned int start_slot)
{
int i, j;
- unsigned int count = num_params;
+ unsigned int count = num_slots;
+ int stop_slot = start_slot;
+ DECLARE_BITMAP(tmp_inuse, EDMA_MAX_PARAMENTRY);
- for (i = start_param; i < edma_info[ctlr]->num_slots; ++i) {
+ for (i = start_slot; i < edma_info[ctlr]->num_slots; ++i) {
j = EDMA_CHAN_SLOT(i);
- if (!test_and_set_bit(j, edma_info[ctlr]->edma_inuse))
+ if (!test_and_set_bit(j, edma_info[ctlr]->edma_inuse)) {
+ /* Record our current beginning slot */
+ if (count == num_slots)
+ stop_slot = i;
+
count--;
+ set_bit(j, tmp_inuse);
+
if (count == 0)
break;
- else if (id == EDMA_CONT_PARAMS_FIXED_EXACT)
- break;
- else
- count = num_params;
+ } else {
+ clear_bit(j, tmp_inuse);
+
+ if (id == EDMA_CONT_PARAMS_FIXED_EXACT) {
+ stop_slot = i;
+ break;
+ } else
+ count = num_slots;
+ }
}
/*
* We have to clear any bits that we set
- * if we run out parameter RAMs, i.e we do find a set
- * of contiguous parameter RAMs but do not find the exact number
- * requested as we may reach the total number of parameter RAMs
+ * if we run out parameter RAM slots, i.e we do find a set
+ * of contiguous parameter RAM slots but do not find the exact number
+ * requested as we may reach the total number of parameter RAM slots
*/
- if (count) {
- for (j = i - num_params + count + 1; j <= i ; ++j)
+ if (i == edma_info[ctlr]->num_slots)
+ stop_slot = i;
+
+ for (j = start_slot; j < stop_slot; j++)
+ if (test_bit(j, tmp_inuse))
clear_bit(j, edma_info[ctlr]->edma_inuse);
+ if (count)
return -EBUSY;
- }
- for (j = i - num_params + 1; j <= i; ++j)
+ for (j = i - num_slots + 1; j <= i; ++j)
memcpy_toio(edmacc_regs_base[ctlr] + PARM_OFFSET(j),
&dummy_paramset, PARM_SIZE);
- return EDMA_CTLR_CHAN(ctlr, i - num_params + 1);
+ return EDMA_CTLR_CHAN(ctlr, i - num_slots + 1);
}
/*-----------------------------------------------------------------------*/
/**
* edma_alloc_cont_slots- alloc contiguous parameter RAM slots
* The API will return the starting point of a set of
- * contiguous PARAM's that have been requested
+ * contiguous parameter RAM slots that have been requested
*
* @id: can only be EDMA_CONT_PARAMS_ANY or EDMA_CONT_PARAMS_FIXED_EXACT
* or EDMA_CONT_PARAMS_FIXED_NOT_EXACT
- * @count: number of contiguous Paramter RAM's
- * @param - the start value of Parameter RAM that should be passed if id
+ * @count: number of contiguous Paramter RAM slots
+ * @slot - the start value of Parameter RAM slot that should be passed if id
* is EDMA_CONT_PARAMS_FIXED_EXACT or EDMA_CONT_PARAMS_FIXED_NOT_EXACT
*
* If id is EDMA_CONT_PARAMS_ANY then the API starts looking for a set of
- * contiguous Parameter RAMs from parameter RAM 64 in the case of DaVinci SOCs
- * and 32 in the case of Primus
+ * contiguous Parameter RAM slots from parameter RAM 64 in the case of
+ * DaVinci SOCs and 32 in the case of DA8xx SOCs.
*
* If id is EDMA_CONT_PARAMS_FIXED_EXACT then the API starts looking for a
- * set of contiguous parameter RAMs from the "param" that is passed as an
+ * set of contiguous parameter RAM slots from the "slot" that is passed as an
* argument to the API.
*
* If id is EDMA_CONT_PARAMS_FIXED_NOT_EXACT then the API initially tries
- * starts looking for a set of contiguous parameter RAMs from the "param"
+ * starts looking for a set of contiguous parameter RAMs from the "slot"
* that is passed as an argument to the API. On failure the API will try to
- * find a set of contiguous Parameter RAMs in the remaining Parameter RAMs
+ * find a set of contiguous Parameter RAM slots from the remaining Parameter
+ * RAM slots
*/
int edma_alloc_cont_slots(unsigned ctlr, unsigned int id, int slot, int count)
{
* the number of channels and lesser than the total number
* of slots
*/
- if (slot < edma_info[ctlr]->num_channels ||
- slot >= edma_info[ctlr]->num_slots)
+ if ((id != EDMA_CONT_PARAMS_ANY) &&
+ (slot < edma_info[ctlr]->num_channels ||
+ slot >= edma_info[ctlr]->num_slots))
return -EINVAL;
/*
- * The number of parameter RAMs requested cannot be less than 1
+ * The number of parameter RAM slots requested cannot be less than 1
* and cannot be more than the number of slots minus the number of
* channels
*/
switch (id) {
case EDMA_CONT_PARAMS_ANY:
- return reserve_contiguous_params(ctlr, id, count,
+ return reserve_contiguous_slots(ctlr, id, count,
edma_info[ctlr]->num_channels);
case EDMA_CONT_PARAMS_FIXED_EXACT:
case EDMA_CONT_PARAMS_FIXED_NOT_EXACT:
- return reserve_contiguous_params(ctlr, id, count, slot);
+ return reserve_contiguous_slots(ctlr, id, count, slot);
default:
return -EINVAL;
}
EXPORT_SYMBOL(edma_alloc_cont_slots);
/**
- * edma_free_cont_slots - deallocate DMA parameter RAMs
- * @slot: first parameter RAM of a set of parameter RAMs to be freed
- * @count: the number of contiguous parameter RAMs to be freed
+ * edma_free_cont_slots - deallocate DMA parameter RAM slots
+ * @slot: first parameter RAM of a set of parameter RAM slots to be freed
+ * @count: the number of contiguous parameter RAM slots to be freed
*
* This deallocates the parameter RAM slots allocated by
* edma_alloc_cont_slots.
* Callers/applications need to keep track of sets of contiguous
- * parameter RAMs that have been allocated using the edma_alloc_cont_slots
+ * parameter RAM slots that have been allocated using the edma_alloc_cont_slots
* API.
* Callers are responsible for ensuring the slots are inactive, and will
* not be activated.
*/
int edma_free_cont_slots(unsigned slot, int count)
{
- unsigned ctlr;
+ unsigned ctlr, slot_to_free;
int i;
ctlr = EDMA_CTLR(slot);
for (i = slot; i < slot + count; ++i) {
ctlr = EDMA_CTLR(i);
- slot = EDMA_CHAN_SLOT(i);
+ slot_to_free = EDMA_CHAN_SLOT(i);
- memcpy_toio(edmacc_regs_base[ctlr] + PARM_OFFSET(slot),
+ memcpy_toio(edmacc_regs_base[ctlr] + PARM_OFFSET(slot_to_free),
&dummy_paramset, PARM_SIZE);
- clear_bit(slot, edma_info[ctlr]->edma_inuse);
+ clear_bit(slot_to_free, edma_info[ctlr]->edma_inuse);
}
return 0;
#include <linux/errno.h>
#include <linux/kernel.h>
-#include <linux/list.h>
-#include <linux/module.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/bitops.h>
-#include <mach/cputype.h>
-#include <mach/irqs.h>
-#include <mach/hardware.h>
-#include <mach/common.h>
#include <mach/gpio.h>
#include <asm/mach/irq.h>
-
static DEFINE_SPINLOCK(gpio_lock);
struct davinci_gpio {
#define DAVINCI_ASP0_BASE 0x01E02000
#define DAVINCI_ASP1_BASE 0x01E04000
+/* Bases of dm365 register banks */
+#define DAVINCI_DM365_ASP0_BASE 0x01D02000
+
/* Bases of dm646x register banks */
#define DAVINCI_DM646X_MCASP0_REG_BASE 0x01D01000
#define DAVINCI_DM646X_MCASP1_REG_BASE 0x01D01800
extern void __iomem *davinci_intc_base;
extern int davinci_intc_type;
-/* parameters describe VBUS sourcing for host mode */
-extern void setup_usb(unsigned mA, unsigned potpgt_msec);
-
-/* parameters describe VBUS sourcing for host mode */
-extern void setup_usb(unsigned mA, unsigned potpgt_msec);
-
struct davinci_timer_instance {
void __iomem *base;
u32 bottom_irq;
--- /dev/null
+/*
+ * TI DaVinci CPUFreq platform support.
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc. http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef _MACH_DAVINCI_CPUFREQ_H
+#define _MACH_DAVINCI_CPUFREQ_H
+
+#include <linux/cpufreq.h>
+
+struct davinci_cpufreq_config {
+ struct cpufreq_frequency_table *freq_table;
+ int (*set_voltage) (unsigned int index);
+ int (*init) (void);
+};
+
+#endif
--- /dev/null
+/*
+ * TI DaVinci cpuidle platform support
+ *
+ * 2009 (C) Texas Instruments, Inc. http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+#ifndef _MACH_DAVINCI_CPUIDLE_H
+#define _MACH_DAVINCI_CPUIDLE_H
+
+struct davinci_cpuidle_config {
+ u32 ddr2_pdown;
+};
+
+#endif
#ifndef __ASM_ARCH_DAVINCI_DA8XX_H
#define __ASM_ARCH_DAVINCI_DA8XX_H
+#include <video/da8xx-fb.h>
+
#include <mach/serial.h>
#include <mach/edma.h>
#include <mach/i2c.h>
#include <mach/emac.h>
#include <mach/asp.h>
#include <mach/mmc.h>
+#include <mach/usb.h>
+
+extern void __iomem *da8xx_syscfg_base;
/*
* The cp_intc interrupt controller for the da8xx isn't in the same
#define DA8XX_CP_INTC_SIZE SZ_8K
#define DA8XX_CP_INTC_VIRT (IO_VIRT - DA8XX_CP_INTC_SIZE - SZ_4K)
-#define DA8XX_BOOT_CFG_BASE (IO_PHYS + 0x14000)
+#define DA8XX_SYSCFG_BASE (IO_PHYS + 0x14000)
+#define DA8XX_SYSCFG_VIRT(x) (da8xx_syscfg_base + (x))
+#define DA8XX_JTAG_ID_REG 0x18
+#define DA8XX_CFGCHIP0_REG 0x17c
+#define DA8XX_CFGCHIP2_REG 0x184
+#define DA8XX_CFGCHIP3_REG 0x188
#define DA8XX_PSC0_BASE 0x01c10000
#define DA8XX_PLL0_BASE 0x01c11000
-#define DA8XX_JTAG_ID_REG 0x01c14018
#define DA8XX_TIMER64P0_BASE 0x01c20000
#define DA8XX_TIMER64P1_BASE 0x01c21000
#define DA8XX_GPIO_BASE 0x01e26000
#define DA8XX_AEMIF_CS2_BASE 0x60000000
#define DA8XX_AEMIF_CS3_BASE 0x62000000
#define DA8XX_AEMIF_CTL_BASE 0x68000000
+#define DA8XX_DDR2_CTL_BASE 0xb0000000
#define PINMUX0 0x00
#define PINMUX1 0x04
int da8xx_register_edma(void);
int da8xx_register_i2c(int instance, struct davinci_i2c_platform_data *pdata);
int da8xx_register_watchdog(void);
+int da8xx_register_usb20(unsigned mA, unsigned potpgt);
+int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
int da8xx_register_emac(void);
-int da8xx_register_lcdc(void);
+int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata);
int da8xx_register_mmcsd0(struct davinci_mmc_config *config);
-void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata);
+void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata);
+int da8xx_register_rtc(void);
+int da850_register_cpufreq(void);
+int da8xx_register_cpuidle(void);
extern struct platform_device da8xx_serial_device;
extern struct emac_platform_data da8xx_emac_pdata;
+extern struct da8xx_lcdc_platform_data sharp_lcd035q3dg01_pdata;
+extern struct da8xx_lcdc_platform_data sharp_lk043t1dg01_pdata;
extern const short da830_emif25_pins[];
extern const short da830_spi0_pins[];
extern const short da850_i2c0_pins[];
extern const short da850_i2c1_pins[];
extern const short da850_cpgmac_pins[];
+extern const short da850_rmii_pins[];
extern const short da850_mcasp_pins[];
extern const short da850_lcdcntl_pins[];
extern const short da850_mmcsd0_pins[];
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <mach/emac.h>
+#include <mach/asp.h>
+#include <mach/keyscan.h>
#define DM365_EMAC_BASE (0x01D07000)
#define DM365_EMAC_CNTRL_OFFSET (0x0000)
#define DM365_EMAC_MDIO_OFFSET (0x4000)
#define DM365_EMAC_CNTRL_RAM_SIZE (0x2000)
+/* Base of key scan register bank */
+#define DM365_KEYSCAN_BASE (0x01C69400)
+
+#define DM365_RTC_BASE (0x01C69000)
+
void __init dm365_init(void);
+void __init dm365_init_asp(struct snd_platform_data *pdata);
+void __init dm365_init_ks(struct davinci_ks_platform_data *pdata);
+void __init dm365_init_rtc(void);
#endif /* __ASM_ARCH_DM365_H */
#ifndef __ASM_ARCH_DM644X_H
#define __ASM_ARCH_DM644X_H
-#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <mach/emac.h>
#include <mach/asp.h>
#define IRQ_DM365_SDIOINT0 23
#define IRQ_DM365_MMCINT1 27
#define IRQ_DM365_PWMINT3 28
+#define IRQ_DM365_RTCINT 29
#define IRQ_DM365_SDIOINT1 31
#define IRQ_DM365_SPIINT0_0 42
#define IRQ_DM365_SPIINT3_0 43
/* AEAW functions */
DM644X_AEAW,
+ DM644X_AEAW0,
+ DM644X_AEAW1,
+ DM644X_AEAW2,
+ DM644X_AEAW3,
+ DM644X_AEAW4,
/* Memory Stick */
DM644X_MSTK,
DM365_EMAC_MDIO,
DM365_EMAC_MDCLK,
- /* Keypad */
- DM365_KEYPAD,
+ /* Key Scan */
+ DM365_KEYSCAN,
/* PWM */
DM365_PWM0,
DA850_MII_RXD_0,
DA850_MDIO_CLK,
DA850_MDIO_D,
+ DA850_RMII_TXD_0,
+ DA850_RMII_TXD_1,
+ DA850_RMII_TXEN,
+ DA850_RMII_CRS_DV,
+ DA850_RMII_RXD_0,
+ DA850_RMII_RXD_1,
+ DA850_RMII_RXER,
+ DA850_RMII_MHZ_50_CLK,
/* McASP function */
DA850_ACLKR,
DA850_NEMA_CS_2,
/* GPIO function */
+ DA850_GPIO2_6,
+ DA850_GPIO2_8,
DA850_GPIO2_15,
- DA850_GPIO8_10,
DA850_GPIO4_0,
DA850_GPIO4_1,
};
#ifndef __ASM_ARCH_SYSTEM_H
#define __ASM_ARCH_SYSTEM_H
-#include <linux/io.h>
-#include <mach/hardware.h>
-
extern void davinci_watchdog_reset(void);
static inline void arch_idle(void)
--- /dev/null
+/*
+ * USB related definitions
+ *
+ * Copyright (C) 2009 MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_USB_H
+#define __ASM_ARCH_USB_H
+
+/* DA8xx CFGCHIP2 (USB 2.0 PHY Control) register bits */
+#define CFGCHIP2_PHYCLKGD (1 << 17)
+#define CFGCHIP2_VBUSSENSE (1 << 16)
+#define CFGCHIP2_RESET (1 << 15)
+#define CFGCHIP2_OTGMODE (3 << 13)
+#define CFGCHIP2_NO_OVERRIDE (0 << 13)
+#define CFGCHIP2_FORCE_HOST (1 << 13)
+#define CFGCHIP2_FORCE_DEVICE (2 << 13)
+#define CFGCHIP2_FORCE_HOST_VBUS_LOW (3 << 13)
+#define CFGCHIP2_USB1PHYCLKMUX (1 << 12)
+#define CFGCHIP2_USB2PHYCLKMUX (1 << 11)
+#define CFGCHIP2_PHYPWRDN (1 << 10)
+#define CFGCHIP2_OTGPWRDN (1 << 9)
+#define CFGCHIP2_DATPOL (1 << 8)
+#define CFGCHIP2_USB1SUSPENDM (1 << 7)
+#define CFGCHIP2_PHY_PLLON (1 << 6) /* override PLL suspend */
+#define CFGCHIP2_SESENDEN (1 << 5) /* Vsess_end comparator */
+#define CFGCHIP2_VBDTCTEN (1 << 4) /* Vbus comparator */
+#define CFGCHIP2_REFFREQ (0xf << 0)
+#define CFGCHIP2_REFFREQ_12MHZ (1 << 0)
+#define CFGCHIP2_REFFREQ_24MHZ (2 << 0)
+#define CFGCHIP2_REFFREQ_48MHZ (3 << 0)
+
+struct da8xx_ohci_root_hub;
+
+typedef void (*da8xx_ocic_handler_t)(struct da8xx_ohci_root_hub *hub,
+ unsigned port);
+
+/* Passed as the platform data to the OHCI driver */
+struct da8xx_ohci_root_hub {
+ /* Switch the port power on/off */
+ int (*set_power)(unsigned port, int on);
+ /* Read the port power status */
+ int (*get_power)(unsigned port);
+ /* Read the port over-current indicator */
+ int (*get_oci)(unsigned port);
+ /* Over-current indicator change notification (pass NULL to disable) */
+ int (*ocic_notify)(da8xx_ocic_handler_t handler);
+
+ /* Time from power on to power good (in 2 ms units) */
+ u8 potpgt;
+};
+
+void davinci_setup_usb(unsigned mA, unsigned potpgt_ms);
+
+#endif /* ifndef __ASM_ARCH_USB_H */
#include <linux/module.h>
#include <linux/spinlock.h>
-#include <mach/hardware.h>
#include <mach/mux.h>
#include <mach/common.h>
*
*/
#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
#include <linux/io.h>
#include <mach/cputype.h>
-#include <mach/hardware.h>
#include <mach/psc.h>
-#include <mach/mux.h>
/* PSC register offsets */
#define EPCPR 0x070
#include <linux/clk.h>
#include <linux/io.h>
-#include <asm/irq.h>
-#include <mach/hardware.h>
#include <mach/serial.h>
-#include <mach/irqs.h>
#include <mach/cputype.h>
-#include <mach/common.h>
-
-#include "clock.h"
static inline unsigned int serial_read_reg(struct plat_serial8250_port *up,
int offset)
* (at your option) any later version.
*/
#include <linux/module.h>
-#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/genalloc.h>
#include <mach/common.h>
-#include <mach/memory.h>
#include <mach/sram.h>
-
static struct gen_pool *sram_pool;
void *sram_alloc(size_t len, dma_addr_t *dma)
#include <linux/interrupt.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
-#include <linux/spinlock.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/err.h>
-#include <linux/device.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
-#include <asm/system.h>
-#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include <asm/errno.h>
-#include <mach/io.h>
#include <mach/cputype.h>
#include <mach/time.h>
#include "clock.h"
/*
* USB
*/
-#include <linux/kernel.h>
-#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/usb/musb.h>
-#include <linux/usb/otg.h>
#include <mach/common.h>
-#include <mach/hardware.h>
#include <mach/irqs.h>
#include <mach/cputype.h>
+#include <mach/usb.h>
-#define DAVINCI_USB_OTG_BASE 0x01C64000
+#define DAVINCI_USB_OTG_BASE 0x01c64000
+
+#define DA8XX_USB0_BASE 0x01e00000
+#define DA8XX_USB1_BASE 0x01e25000
#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
static struct musb_hdrc_eps_bits musb_eps[] = {
.num_resources = ARRAY_SIZE(usb_resources),
};
-void __init setup_usb(unsigned mA, unsigned potpgt_msec)
+void __init davinci_setup_usb(unsigned mA, unsigned potpgt_ms)
{
- usb_data.power = mA / 2;
- usb_data.potpgt = potpgt_msec / 2;
+ usb_data.power = mA > 510 ? 255 : mA / 2;
+ usb_data.potpgt = (potpgt_ms + 1) / 2;
if (cpu_is_davinci_dm646x()) {
/* Override the defaults as DM6467 uses different IRQs. */
platform_device_register(&usb_dev);
}
+#ifdef CONFIG_ARCH_DAVINCI_DA8XX
+static struct resource da8xx_usb20_resources[] = {
+ {
+ .start = DA8XX_USB0_BASE,
+ .end = DA8XX_USB0_BASE + SZ_64K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_DA8XX_USB_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+int __init da8xx_register_usb20(unsigned mA, unsigned potpgt)
+{
+ usb_data.clock = "usb20";
+ usb_data.power = mA > 510 ? 255 : mA / 2;
+ usb_data.potpgt = (potpgt + 1) / 2;
+
+ usb_dev.resource = da8xx_usb20_resources;
+ usb_dev.num_resources = ARRAY_SIZE(da8xx_usb20_resources);
+
+ return platform_device_register(&usb_dev);
+}
+#endif /* CONFIG_DAVINCI_DA8XX */
+
#else
-void __init setup_usb(unsigned mA, unsigned potpgt_msec)
+void __init davinci_setup_usb(unsigned mA, unsigned potpgt_ms)
{
}
+#ifdef CONFIG_ARCH_DAVINCI_DA8XX
+int __init da8xx_register_usb20(unsigned mA, unsigned potpgt)
+{
+ return 0;
+}
+#endif
+
#endif /* CONFIG_USB_MUSB_HDRC */
+#ifdef CONFIG_ARCH_DAVINCI_DA8XX
+static struct resource da8xx_usb11_resources[] = {
+ [0] = {
+ .start = DA8XX_USB1_BASE,
+ .end = DA8XX_USB1_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_DA8XX_IRQN,
+ .end = IRQ_DA8XX_IRQN,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 da8xx_usb11_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device da8xx_usb11_device = {
+ .name = "ohci",
+ .id = 0,
+ .dev = {
+ .dma_mask = &da8xx_usb11_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+ .num_resources = ARRAY_SIZE(da8xx_usb11_resources),
+ .resource = da8xx_usb11_resources,
+};
+
+int __init da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata)
+{
+ da8xx_usb11_device.dev.platform_data = pdata;
+ return platform_device_register(&da8xx_usb11_device);
+}
+#endif /* CONFIG_DAVINCI_DA8XX */
projects / mv-sheeva.git / commitdiff