- Addaptations of Andrey Borzenkov applied to 7.22 source
- Alterations to avoid most HCF_ASSERTs
-- Switching interrupts off and on in the HCF
--- Bugfixes, things that were aparently wrong like reporting link status
+-- Bugfixes, things that were apparently wrong like reporting link status
change which checked a variable that was not changed in HCF anymore.
-- Used on WEP but setting keys via SIOCSIWENCODEEXT was not supported
-- Recovery actions added
* hcfcfg.tpl list all #defines which must be specified to:
* adjust the HCF functions defined in HCF.C to the characteristics of a specific environment
* o maximum sizes for messages
-* o Endianess
+* o Endianness
* Compiler specific macros
* o port I/O macros
* o type definitions
#if 0 //get compiler going
#if HCF_EX_INT_TICK != HREG_EV_TICK
;? out dated checking
-err: someone redefined these macros while the implemenation assumes they are equal;
+err: someone redefined these macros while the implementation assumes they are equal;
#endif
#if HCF_EX_INT_TX_OK != HFS_TX_CNTL_TX_OK || HFS_TX_CNTL_TX_OK != HREG_EV_TX_OK
;? out dated checking
-err: someone redefined these macros while the implemenation assumes they are equal;
+err: someone redefined these macros while the implementation assumes they are equal;
#endif
#if HCF_EX_INT_TX_EX != HFS_TX_CNTL_TX_EX || HFS_TX_CNTL_TX_EX != HREG_EV_TX_EX
;? out dated checking
-err: someone redefined these macros while the implemenation assumes they are equal;
+err: someone redefined these macros while the implementation assumes they are equal;
#endif
#endif // 0 get compiler going
#define HCF_SUCCESS 0x00 // OK
-#define HCF_ERR_TIME_OUT 0x04 // Expected Hermes event did not occure in expected time
+#define HCF_ERR_TIME_OUT 0x04 // Expected Hermes event did not occur in expected time
#define HCF_ERR_NO_NIC 0x05 /* card not found (usually yanked away during hcfio_in_string
* Also: card is either absent or disabled while it should be neither */
#define HCF_ERR_LEN 0x08 /* buffer size insufficient
* - IFB_ConfigTable too small
* - hcf_get_info buffer has a size of 0 or 1 or less than needed
- * to accomodate all data
+ * to accommodate all data
* - hcf_put_info: CFG_DLNV_DATA exceeds intermediate
* buffer size */
#define HCF_ERR_INCOMP_PRI 0x09 // primary functions are not compatible
// Manufacture ID: 0156,0003
// Lowest measurment for noise floor seen is value 54
// Highest signal strength in close proximity to the AP seen is value 118
-// Very good must be arround 100 (otherwise its never "full scale"
+// Very good must be around 100 (otherwise its never "full scale"
// All other constants are derrived from these. This makes the signal gauge
// work for me...
#define HCF_MIN_SIGNAL_LEVEL 54
*
*------------------------------------------------------------------------------
*
- * Header for defintions and macros internal to the drvier.
+ * Header for definitions and macros internal to the drvier.
*
*------------------------------------------------------------------------------
*
#include <wl_pci.h>
#endif /* BUS_PCI */
/*******************************************************************************
- * macro defintions
+ * macro definitions
******************************************************************************/
#define VALID_PARAM(C) \
{ \
lp->ltvRecord.u.u16[0] = CNV_INT_TO_LITTLE( lp->TxRateControl[0] );
#endif // WARP
-//;?skip temporarily to see whether the RID or something else is the probelm hcf_status = hcf_put_info( &lp->hcfCtx, (LTVP)&( lp->ltvRecord ));
+//;?skip temporarily to see whether the RID or something else is the problem hcf_status = hcf_put_info( &lp->hcfCtx, (LTVP)&( lp->ltvRecord ));
DBG_TRACE( DbgInfo, "CFG_TX_RATE_CNTL 2.4GHz : 0x%04x\n",
lp->TxRateControl[0] );
netif_stop_queue( dev );
- /* Allocate virutal devices for WDS support if needed */
+ /* Allocate virtual devices for WDS support if needed */
WL_WDS_DEVICE_ALLOC( lp );
DBG_LEAVE( DbgInfo );
* DESCRIPTION:
*
* Registered in the pci_driver structure, this function is called when the
- * PCI subsystem finds a new PCI device which matches the infomation contained
+ * PCI subsystem finds a new PCI device which matches the information contained
* in the pci_device_id table.
*
* PARAMETERS:
* DESCRIPTION:
*
* Registered in the pci_driver structure, this function is called when the
- * PCI subsystem detects that a PCI device which matches the infomation
+ * PCI subsystem detects that a PCI device which matches the information
* contained in the pci_device_id table has been removed.
*
* PARAMETERS:
*
* DESCRIPTION:
*
- * Disonnect from the UIL after a request has been completed.
+ * Disconnect from the UIL after a request has been completed.
*
* PARAMETERS:
*
memset(byte_field, '\0', 3);
while (value[value_offset] != '\0') {
- /* Skip over the colon chars seperating the bytes, if they exist */
+ /* Skip over the colon chars separating the bytes, if they exist */
if (value[value_offset] == ':') {
value_offset++;
continue;
/*******************************************************************************
- * bus architechture specific defines, includes, etc.
+ * bus architecture specific defines, includes, etc.
******************************************************************************/
/*
* There doesn't seem to be a difference for PCMCIA and PCI anymore, at least
int retries = 0;
/*------------------------------------------------------------------------*/
- //;? Note: shows results as trace, retruns always 0 unless BUSY
+ //;? Note: shows results as trace, returns always 0 unless BUSY
DBG_FUNC( "wireless_set_scan" );
DBG_ENTER( DbgInfo );
projects / karo-tx-linux.git / commitdiff