Add support for new RF chip ID: 3070. It seems to be the same as 5370,
maybe vendor just put wrong value on the eeprom, but add this id anyway
since devices with it showed on the marked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: Use fw filename and nvram based of devid for sdio.
SDIO firmware download routines uses one name for firmware file
and nvram file for all sdio devices. This is not user friendly.
Use fw filename and nvram filename based upon chip id and revision.
Reported-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The definition of BRCMF_EVENTING_MASK_LEN results in a sparse
error message
.../fweh.c:331:22: error: bad constant expression
.../fweh.c:388:22: error: bad constant expression
.../dhd_common.c:256:22: error: bad constant expression
This is caused by the use of roundup() in BRCMF_EVENTING_MASK_LEN
and it is used to allocate an array variable on the stack. Better
use DIV_ROUND_UP() macro.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 25 Sep 2013 11:05:43 +0000 (13:05 +0200)]
brcmfmac: reserve memory for bus layer in sk_buff::cb
Bus layer need to share sk_buff::cb with firmware signal feature. Reserve
necessary memory so they won't overwrite each other.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 25 Sep 2013 11:05:40 +0000 (13:05 +0200)]
brcmfmac: sync firmware event list
Update event list to keep sync with firmware development. Use calculated event
mask length instead of hard-coded value.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel Holtmann [Thu, 3 Oct 2013 08:26:37 +0000 (01:26 -0700)]
Bluetooth: Only one command per L2CAP LE signalling is supported
The Bluetooth specification makes it clear that only one command
should be present in the L2CAP LE signalling packet. So tighten
the checks here and restrict it to exactly one command.
This is different from L2CAP BR/EDR signalling where multiple
commands can be part of the same packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 06:37:29 +0000 (23:37 -0700)]
Bluetooth: Allow changing device class when BR/EDR is disabled
Changing the device class when BR/EDR is disabled has no visible
effect for remote devices. However to simplify the logic allow it
as long as the controller supports BR/EDR operations.
If it is not allowed, then the overall logic becomes rather
complicated since the class of device values would need clearing
or restoring when BR/EDR setting changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 04:16:08 +0000 (21:16 -0700)]
Bluetooth: Restrict loading of long term keys to LE capable controllers
Loading long term keys into a BR/EDR only controller make no sense.
The kernel would never use any of these keys. So instead of allowing
userspace to waste memory, reject such operation with a not supported
error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 04:16:07 +0000 (21:16 -0700)]
Bluetooth: Restrict loading of link keys to BR/EDR capable controllers
Loading link keys into a LE only controller make no sense. The kernel
would never use any of these keys. So instead of allowing userspace
to waste memory, reject such operation with a not supported error
message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 05:10:32 +0000 (22:10 -0700)]
Bluetooth: Allow setting static address even if LE is disabled
Setting the static address does not depend on LE beeing enabled. It
only depends on a controller with LE support.
When depending on LE enabled this command becomes really complicated
since in case LE gets disabled, it would be required to clear the
static address and also its random address representation inside
the controller. With future support for private addresses such
complex setup should be avoided.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Thu, 3 Oct 2013 04:31:52 +0000 (21:31 -0700)]
Bluetooth: Restrict SSP setting changes to BR/EDR enabled controllers
Only when BR/EDR is supported and enabled, allow changing of the SSP
setting. Just checking if the hardware supports SSP is not enough
since it might be the case that BR/EDR is disabled.
In the case that BR/EDR is disabled, but SSP supported by the
controller the not supported error message is now returned.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 15:28:21 +0000 (08:28 -0700)]
Bluetooth: Fix memory leak with L2CAP signal channels
The wrong type of L2CAP signalling packets on the wrong type of
either BR/EDR or LE links need to be dropped. When that happens
the packet is dropped, but the memory not freed. So actually
free the memory as well.
DoHyun Pyun [Wed, 2 Oct 2013 12:54:53 +0000 (21:54 +0900)]
Bluetooth: Add the definition for Slave Page Response Timeout
The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 110
"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.
Event Parameters: NONE"
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Status 0x00 Start Synchronization Train command completed
successfully.
0x01-0xFF Start Synchronization Train command failed.
See Part D, Error Codes, for error codes and
descriptions."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:51 +0000 (21:54 +0900)]
Bluetooth: Add the definition for Start Synchronization Train
The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 86
"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.
Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:50 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Set CSB
he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 78
"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.
The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.
The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.
The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:49 +0000 (21:54 +0900)]
Bluetooth: Add the structure for Write Sync Train Parameters
The Write_Synchronization_Train_Parameters command configures
the Synchronization Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 97
"7.3.90 Write Synchronization Train Parameters Command [New Section]
...
Note: The AFH_Channel_Map used in the Synchronization Train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
Interval_Min and Interval_Max specify the allowed range of
Sync_Train_Interval. Refer to [Vol. 2], Part B, section 2.7.2 for
a detailed description of Sync_Train_Interval. The BR/EDR Controller shall
select an interval from this range and return it in Sync_Train_Interval.
If the Controller is unable to select a value from this range, it shall
return the Invalid HCI Command Parameters (0x12) error code.
Once started (via the Start_Synchronization_Train Command) the
Synchronization Train will continue until synchronization_trainTO slots have
passed or Connectionless Slave Broadcast has been disabled."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:48 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Set CSB Data
The Set_Connectionless_Slave_Broadcast_Data command provides the
ability for the Host to set Connectionless Slave Broadcast data in
the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 93
"7.3.88 Set Connectionless Slave Broadcast Data Command [New Section]
...
If connectionless slave broadcast mode is disabled, this data shall be
kept by the BR/EDR Controller and used once connectionless slave broadcast
mode is enabled. If connectionless slave broadcast mode is enabled,
and this command is successful, this data will be sent starting with
the next Connectionless Slave Broadcast instant.
The Data_Length field may be zero, in which case no data needs to be
provided.
The Host may fragment the data using the Fragment field in the command. If
the combined length of the fragments exceeds the capacity of the largest
allowed packet size specified in the Set Connectionless Slave Broadcast
command, all fragments associated with the data being assembled shall be
discarded and the Invalid HCI Command Parameters error (0x12) shall be
returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:47 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Delete Reserved LT_ADDR
The Delete_Reserved_LT_ADDR command requests that the BR/EDR
Controller cancel the reservation for a specific LT_ADDR reserved for the
purposes of Connectionless Slave Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 92
"7.3.87 Delete Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is not reserved by the
BR/EDR Controller, it shall return the Unknown Connection Identifier (0x02)
error code.
If connectionless slave broadcast mode is still active, then the Controller
shall return the Command Disallowed (0x0C) error code."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DoHyun Pyun [Wed, 2 Oct 2013 12:54:46 +0000 (21:54 +0900)]
Bluetooth: Add the definition and structure for Set Reserved LT_ADDR
The Set_Reserved_LT_ADDR command allows the host to request that the
BR/EDR Controller reserve a specific LT_ADDR for Connectionless Slave
Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 90
"7.3.86 Set Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is already in use by the
BR/EDR Controller, it shall return the ACL Connection Already Exists (0x0B)
error code. If the LT_ADDR indicated in the LT_ADDR parameter is out of
range, the controller shall return the Invalid HCI Command Parameters (0x12)
error code. If the command succeeds, then the reserved LT_ADDR shall be
used when issuing subsequent Set Connectionless Slave Broadcast Data and
Set Connectionless Slave Broadcast commands.
To ensure that the reserved LT_ADDR is not already allocated, it is
recommended that this command be issued at some point after HCI_Reset is
issued but before page scanning is enabled or paging is initiated."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com> Signed-off-by: C S Bhargava <cs.bhargava@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 2 Oct 2013 13:02:24 +0000 (16:02 +0300)]
Bluetooth: Fix advertising data flags with disabled BR/EDR
We shouldn't include the simultaneous LE & BR/EDR flags in the LE
advertising data if BR/EDR is disabled on a dual-mode controller. This
patch fixes this issue and ensures that the create_ad function generates
the correct flags when BR/EDR is disabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 2 Oct 2013 12:45:22 +0000 (15:45 +0300)]
Bluetooth: Fix REJECTED vs NOT_SUPPORTED mgmt responses
The REJECTED management response should mainly be used when the adapter
is in a state where we cannot accept some command or a specific
parameter value. The NOT_SUPPORTED response in turn means that the
adapter really cannot support the command or parameter value.
This patch fixes this distinction and adds two helper functions to
easily get the appropriate LE or BR/EDR related status response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Wed, 2 Oct 2013 11:41:30 +0000 (04:41 -0700)]
Bluetooth: Add management command for setting static address
On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.
This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.
The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 07:27:02 +0000 (00:27 -0700)]
Bluetooth: Restrict disabling of HS when controller is powered off
Disabling the high speed setting when the controller is powered on has
too many side effects that are not taken care of. And in general it
is not an useful operation anyway. So just make such a command fail
with a rejection error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Wed, 2 Oct 2013 10:43:14 +0000 (13:43 +0300)]
Bluetooth: Add a new mgmt_set_bredr command
This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).
Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 2 Oct 2013 10:43:13 +0000 (13:43 +0300)]
Bluetooth: Introduce a new HCI_BREDR_ENABLED flag
To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).
This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.
We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Tue, 1 Oct 2013 19:44:50 +0000 (22:44 +0300)]
Bluetooth: Fix workqueue synchronization in hci_dev_open
When hci_sock.c calls hci_dev_open it needs to ensure that there isn't
pending work in progress, such as that which is scheduled for the
initial setup procedure or the one for automatically powering off after
the setup procedure. This adds the necessary calls to ensure that any
previously scheduled work is completed before attempting to call
hci_dev_do_open.
This patch fixes a race with old user space versions where we might
receive a HCIDEVUP ioctl before the setup procedure has been completed.
When that happens the setup procedures callback may fail early and leave
the device in an inconsistent state, causing e.g. the setup callback to
be (incorrectly) called more than once.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Tue, 1 Oct 2013 19:44:49 +0000 (22:44 +0300)]
Bluetooth: Refactor hci_dev_open to a separate hci_dev_do_open function
The requirements of an external call to hci_dev_open from hci_sock.c are
different to that from within hci_core.c. In the former case we want to
flush any pending work in hdev->req_workqueue whereas in the latter we
don't (since there we are already calling from within the workqueue
itself). This patch does the necessary refactoring to a separate
hci_dev_do_open function (analogous to hci_dev_do_close) but does not
yet introduce the synchronizations relating to the workqueue usage.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Wed, 2 Oct 2013 05:59:25 +0000 (22:59 -0700)]
Bluetooth: Enable -D__CHECK_ENDIAN__ for sparse by default
The Bluetooth protocol and hardware is pretty much all little endian
and so when running sparse via "make C=2" for example, enable the
endian checks by default.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 05:59:24 +0000 (22:59 -0700)]
Bluetooth: Require CAP_NET_ADMIN for HCI User Channel operation
The HCI User Channel operation is an admin operation that puts the
device into promiscuous mode for single use. It is more suitable
to require CAP_NET_ADMIN than CAP_NET_RAW.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 05:59:23 +0000 (22:59 -0700)]
Bluetooth: Send new settings event when changing high speed option
When enabling or disabling high speed setting it is required to send
a new settings event to inform other management interface users about
the changed settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 05:59:22 +0000 (22:59 -0700)]
Bluetooth: Provide high speed configuration option
Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.
This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 05:59:21 +0000 (22:59 -0700)]
Bluetooth: Replace BDADDR_LOCAL with BDADDR_NONE
The BDADDR_LOCAL is a relict from userspace and has never been used
within the kernel. So remove that constant and replace it with a new
BDADDR_NONE that is similar to HCI_DEV_NONE with all bits set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Wed, 2 Oct 2013 05:59:20 +0000 (22:59 -0700)]
Bluetooth: Use only 2 bits for controller type information
The controller type is limited to BR/EDR/LE and AMP controllers. This
can be easily encoded with just 2 bits and still leave enough room
for future controller types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
wl18xx: fix boot process in high temperature environment
In addition to existing WCS PLL configuration add and enable
also the coex PLL during init phase. This fixes boot failures
due to silicon latchup in high temperature environment (>85c).
wlvif could be passed as NULL from the wlcore_tx_work_locked()
to the wl1271_prepare_tx_frame() and to wl1271_skb_queue_head()
functions. This may lead to a Kernel panic, fix this by
validating that wlvif != NULL.
Start a ROC on the AP channel beforing sending the authentication reply
to a connecting STA. This ROC is held up to 1 second via a timer. If the
station is authorized and added by mac80211, the ROC is extended until
the station is fully authorized.
We make sure not to ROC twice when several stations are connecting in
parallel and to only release the ROC when both the pending-reply timer
and the STA-state callbacks do not require it.
rtlwifi: remove duplicate declarations and macros in headers
This patch brings no functional change.
There are still duplicate macros across the rtlwifi directory, for example
IQK_DELAY_TIME is defined multiple times, sometimes with different values,
this patch only removes duplicates within the same header file.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast antenna diversity is required only for single chain
chips and the diversity initialization is done in the
per-family board setup routines. Enabling of diversity
should be done based on the calibrated EEPROM/OTP data,
doing it for all chips is incorrect.
Remove the code that sets the fast_div bit for all cards, since
the documentation for the AR_PHY_CCK_DETECT register says:
reg 642: sig_detect_cck
enable_ant_fast_div : Only used for single chain chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: rt2800lib: fix band selection and LNA PE control for RT3593 PCIe cards
The band selection and PE control code for the
RT3593 chipsets only handles USB based devices
currently. Due to this limitation RT3593 based
PCIe cards are not working correctly.
On PCIe cards band selection is controlled via
GPIO #8 which is identical to the USB devices.
The LNA PE control is slightly different, all
LNA PEs are controlled by GPIO #4.
Update the code to configure the GPIO_CTRL register
correctly on PCIe devices.
Cc: Steven Liu <steven.liu@mediatek.com> Cc: JasonYS Cheng <jasonys.cheng@mediatek.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:
* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.
To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:58:32 +0000 (17:58 +0900)]
wireless: wl12xx: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:57:57 +0000 (17:57 +0900)]
wireless: wlcore: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:57:05 +0000 (17:57 +0900)]
wireless: wl1251: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:56:27 +0000 (17:56 +0900)]
wireless: libertas: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:55:41 +0000 (17:55 +0900)]
wireless: cw1200: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:54:47 +0000 (17:54 +0900)]
wireless: brcmfmac: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:53:02 +0000 (17:53 +0900)]
wireless: ath9k: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jingoo Han [Tue, 10 Sep 2013 08:51:47 +0000 (17:51 +0900)]
wireless: ath5k: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Albert Pool [Mon, 9 Sep 2013 18:36:30 +0000 (20:36 +0200)]
ar5523: Add USB ID of D-Link WUA-2340 rev A1
Signed-off-by: Albert Pool <albertpool@solcon.nl> Reported-by: Michael Landrum <landrummd@gmail.com> Acked-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log