David S. Miller [Fri, 30 Oct 2015 11:19:43 +0000 (20:19 +0900)]
Merge tag 'nfc-next-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.4 pull request
This is the NFC pull request for 4.4.
It's a bit bigger than usual, the 3 main culprits being:
- A new driver for Intel's Fields Peak NCI chipset. In order to
support this chipset we had to export a few NCI routines and
extend the driver NCI ops to not only support proprietary
commands but also core ones.
- Support for vendor commands for both STM drivers, st-nci
and st21nfca. Those vendor commands allow to run factory tests
through the NFC netlink interface.
- New i2c and SPI support for the Marvell driver, together with
firmware download support for this driver's core.
Besides that we also have:
- A few file renames in the STM drivers, to keep the naming
consistent between drivers.
- Some improvements and fixes on the NCI HCI layer, mostly to
properly reach a secure element over a legacy HCI link.
- A few fixes for the s3fwrn5 and trf7970a drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a some more Bluetooth patches for 4.4 which collected up during
the past week. The most important ones are from Kuba Pawlak for fixing
locking issues with SCO sockets. There's also a fix from Alexander Aring
for 6lowpan, a memleak fix from Julia Lawall for the btmrvl driver and
some cleanup patches from Marcel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 26 Oct 2015 18:06:33 +0000 (11:06 -0700)]
ipv6: recreate ipv6 link-local addresses when increasing MTU over IPV6_MIN_MTU
This change makes it so that we reinitialize the interface if the MTU is
increased back above IPV6_MIN_MTU and the interface is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Oct 2015 03:27:07 +0000 (12:27 +0900)]
Merge branch 'mlxsw-flooding-and-cosmetics'
Jiri Pirko says:
====================
mlxsw: driver update
This driver update mainly brings support for user to be able to setup
flooding on specified port, via bridge flag. Also, there is a fix in ageing
time conversion. The rest is just cosmetics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 28 Oct 2015 09:17:04 +0000 (10:17 +0100)]
mlxsw: Put braces on all arms of branch statement
Fix a place where checkpatch complains that braces should be used
on all arms of this statement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 28 Oct 2015 09:17:03 +0000 (10:17 +0100)]
mlxsw: Put constant on the right side of comparisons
Fixes those places where checkpatch complains that comparisons
should place the constant on the right side of the test.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Oct 2015 09:16:57 +0000 (10:16 +0100)]
mlxsw: spectrum: Add support for VLAN ranges in flooding configuration
When enabling a range of VLANs on a bridged port we can configure
flooding for these VLANs by one register access instead of calling the
same register for each VLAN. This is accomplished by using the 'range'
field of the Switch Flooding Table Register (SFTR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Oct 2015 09:16:55 +0000 (10:16 +0100)]
switchdev: Make flood to CPU optional
In certain use cases it is not always desirable for the switch device to
flood traffic to CPU port. Instead, only certain packet types (e.g.
STP, LACP) should be trapped to it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Oct 2015 09:16:54 +0000 (10:16 +0100)]
switchdev: Add support for flood control
Allow devices supporting this feature to control the flooding of unknown
unicast traffic, by making switchdev infrastructure propagate this setting
to the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Oct 2015 03:21:57 +0000 (12:21 +0900)]
Merge branch 'xgene_txrx_delay'
Iyappan Subramanian says:
====================
drivers: xgene: Add support RGMII TX/RX delay configuration
X-Gene RGMII ethernet controller has a RGMII bridge that performs the
task of converting the RGMII signal {RX_CLK,RX_CTL, RX_DATA[3:0]} from
PHY to GMII signal {RX_DV,RX_ER,RX_DATA[7:0]} and vice versa. This
RGMII bridge has a provision to internally delay the input RX_CLK and
the output TX_CLK using configuration registers. This will help in
maintain the CLK-CTL delay relationship in various operating
conditions.
This patch adds support RGMII TX/RX delay configuration.
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers: net: xgene: Add support RGMII TX/RX delay configuration
Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Tue, 27 Oct 2015 14:52:56 +0000 (07:52 -0700)]
bridge: set is_local and is_static before fdb entry is added to the fdb hashtable
Problem Description:
We can add fdbs pointing to the bridge with NULL ->dst but that has a
few race conditions because br_fdb_insert() is used which first creates
the fdb and then, after the fdb has been published/linked, sets
"is_local" to 1 and in that time frame if a packet arrives for that fdb
it may see it as non-local and either do a NULL ptr dereference in
br_forward() or attach the fdb to the port where it arrived, and later
br_fdb_insert() will make it local thus getting a wrong fdb entry.
Call chain br_handle_frame_finish() -> br_forward():
But in br_handle_frame_finish() in order to call br_forward() the dst
should not be local i.e. skb != NULL, whenever the dst is
found to be local skb is set to NULL so we can't forward it,
and here comes the problem since it's running only
with RCU when forwarding packets it can see the entry before "is_local"
is set to 1 and actually try to dereference NULL.
The main issue is that if someone sends a packet to the switch while
it's adding the entry which points to the bridge device, it may
dereference NULL ptr. This is needed now after we can add fdbs
pointing to the bridge. This poses a problem for
br_fdb_update() as well, while someone's adding a bridge fdb, but
before it has is_local == 1, it might get moved to a port if it comes
as a source mac and then it may get its "is_local" set to 1
This patch changes fdb_create to take is_local and is_static as
arguments to set these values in the fdb entry before it is added to the
hash. Also adds null check for port in br_forward.
Fixes: 3741873b4f73 ("bridge: allow adding of fdb entries pointing to the bridge device") Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Tue, 27 Oct 2015 13:49:00 +0000 (09:49 -0400)]
geneve: add IPv6 bits to geneve_fill_metadata_dst
Signed-off-by: John W. Linville <linville@tuxdriver.com> Reviewed-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Mon, 26 Oct 2015 21:01:45 +0000 (17:01 -0400)]
geneve: handle ipv6 priority like ipv4 tos
Other callers of udp_tunnel6_xmit_skb just pass 0 for the prio
argument. Jesse Gross <jesse@nicira.com> suggested that prio is really
the same as IPv4's tos and should be handled the same, so this is my
interpretation of that suggestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Reported-by: Jesse Gross <jesse@nicira.com> Reviewed-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Mon, 26 Oct 2015 21:01:44 +0000 (17:01 -0400)]
geneve: implement support for IPv6-based tunnels
NOTE: Link-local IPv6 addresses for remote endpoints are not supported,
since the driver currently has no capacity for binding a geneve
interface to a specific link.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Reviewed-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Dolca [Mon, 26 Oct 2015 11:58:54 +0000 (13:58 +0200)]
NFC: nci: non-static functions can not be inline
This fixes a build error that seems to be toochain
dependent (Not seen with gcc v5.1):
In file included from net/nfc/nci/rsp.c:36:0:
net/nfc/nci/rsp.c: In function ‘nci_rsp_packet’:
include/net/nfc/nci_core.h:355:12: error: inlining failed in call to
always_inline ‘nci_prop_rsp_packet’: function body not available
inline int nci_prop_rsp_packet(struct nci_dev *ndev, __u16 opcode,
Signed-off-by: Robert Dolca <robert.dolca@intel.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
yankejian [Tue, 27 Oct 2015 11:16:34 +0000 (19:16 +0800)]
net: hisilicon: updates HNS config and documents
updates the bindings documents and dtsi file according to the review
comments[https://lkml.org/lkml/2015/9/21/670] from Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: huangdaode <huangdaode@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Peng [Tue, 27 Oct 2015 09:17:40 +0000 (17:17 +0800)]
net: hns: fixes the bug tested XGE by ethtool -p
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com> Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com> Signed-off-by: yankejian <yankejian@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:56:56 +0000 (19:56 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tycho Andersen [Tue, 27 Oct 2015 00:23:59 +0000 (09:23 +0900)]
seccomp, ptrace: add support for dumping seccomp filters
This patch adds support for dumping a process' (classic BPF) seccomp
filters via ptrace.
PTRACE_SECCOMP_GET_FILTER allows the tracer to dump the user's classic BPF
seccomp filters. addr should be an integer which represents the ith seccomp
filter (0 is the most recently installed filter). data should be a struct
sock_filter * with enough room for the ith filter, or NULL, in which case
the filter is not saved. The return value for this command is the number of
BPF instructions the program represents, or negative in the case of errors.
Command specific errors are ENOENT: which indicates that there is no ith
filter in this seccomp tree, and EMEDIUMTYPE, which indicates that the ith
filter was not installed as a classic BPF filter.
A caveat with this approach is that there is no way to get explicitly at
the heirarchy of seccomp filters, and users need to memcmp() filters to
decide which are inherited. This means that a task which installs two of
the same filter can potentially confuse users of this interface.
v2: * make save_orig const
* check that the orig_prog exists (not necessary right now, but when
grows eBPF support it will be)
* s/n/filter_off and make it an unsigned long to match ptrace
* count "down" the tree instead of "up" when passing a filter offset
v3: * don't take the current task's lock for inspecting its seccomp mode
* use a 0x42** constant for the ptrace command value
v4: * don't copy to userspace while holding spinlocks
v5: * add another condition to WARN_ON
v6: * rebase on net-next
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com> Acked-by: Kees Cook <keescook@chromium.org> CC: Will Drewry <wad@chromium.org> Reviewed-by: Oleg Nesterov <oleg@redhat.com> CC: Andy Lutomirski <luto@amacapital.net> CC: Pavel Emelyanov <xemul@parallels.com> CC: Serge E. Hallyn <serge.hallyn@ubuntu.com> CC: Alexei Starovoitov <ast@kernel.org> CC: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:53:04 +0000 (19:53 -0700)]
Merge branch 'mpls-multipath-improvements'
Robert Shearman says:
====================
mpls: mulipath improvements
Two improvements to the recently added mpls multipath support. The
first is a fix for missing initialisation the nexthop address length
for the v4 and v6 explicit null label routes, and the second is to
reduce the amount of memory used by mpls routes by changing the way
the via addresses are stored.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Tue, 27 Oct 2015 00:37:36 +0000 (00:37 +0000)]
mpls: reduce memory usage of routes
Nexthops for MPLS routes have a via address field sized for the
largest via address that is expected, which is 32 bytes. This means
that in the most common case of having ipv4 via addresses, 28 bytes of
memory more than required are used per nexthop. In the other common
case of an ipv6 nexthop then 16 bytes more than required are
used. With large numbers of MPLS routes this extra memory usage could
start to become significant.
To avoid allocating memory for a maximum length via address when not
all of it is required and to allow for ease of iterating over
nexthops, then the via addresses are changed to be stored in the same
memory block as the route and nexthops, but in an array after the end
of the array of nexthops. New accessors are provided to retrieve a
pointer to the via address.
To allow for O(1) access without having to store a pointer or offset
per nh, the via address for each nexthop is sized according to the
maximum via address for any nexthop in the route, which is stored in a
new route field, rt_max_alen, but this is in an existing hole in
struct mpls_route so it doesn't increase the size of the
structure. Each via address is ensured to be aligned to VIA_ALEN_ALIGN
to account for architectures that don't allow unaligned accesses.
Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Tue, 27 Oct 2015 00:37:35 +0000 (00:37 +0000)]
mpls: fix forwarding using v4/v6 explicit null
Fill in the via address length for the predefined IPv4 and IPv6
explicit-null label routes.
Fixes: f8efb73c97e2 ("mpls: multipath route support") Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 26 Oct 2015 14:23:42 +0000 (14:23 +0000)]
sfc: replace spinlocks with bit ops for busy poll locking
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netstamp_needed is toggled for all socket families if they request
timestamping. But some protocols don't need the lower-layer timestamping
code at all. This patch starts disabling it for af-unix.
E.g. systemd enables timestamping during boot-up on the journald af-unix
sockets, thus causing the system to globally enable timestamping in the
lower networking stack. Still, it is very probable that timestamping
gets activated, by e.g. dhclient or various NTP implementations.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Oct 2015 02:35:01 +0000 (19:35 -0700)]
Merge branch 'qed-driver'
Ariel Elior says:
====================
Add new drivers: qed & qede
This series implements the driver set for Qlogic's new QL4xxx series.
These are 10/20/25/40/50/100 Gig capable converged nics, supporting
ethernet (obviously), iscsi, fcoe, roce and iwarp protocols.
The overall driver design includes a common module ('qed') and protocol
specific dependent modules for ethernet ('qede'), fcoe ('qedf'),
iscsi ('qedi') and roce ('qedr').
The common module contains all of the common logic, e.g. initialization,
cleanup, infrastructure for interrupt handling, link management, slowpath
etc. as well as protocol agnostic features, and supplying an abstraction
layer for other modules.
The protocol specific modules can be compiled and operated independently
of each other, with the exception of the rdma modules which are dependent
on the ethernet module, in accordance with the kernel rdma stack design.
This series only adds the core and ethernet modules, with basic L2
capabilities. Future series will add the rest of the modules and enhance
the L2 functionality.
Ths patch series is constructed of the following patches:
qed: Add module with basic common support
qed: Add basic L2 interface
qede: Add basic Network driver
qed: Add slowpath L2 support
qede: Add basic network device support
qede: Add classification configuration
qed: Add link support
qede: Add support for link
qed: Add statistics support
qede: Add basic ethtool support
This project is a team effort, thanks go to Yuval Mintz, Dmitry Kravkov,
Michal Kalderon, Tomer Tayar, Manish Chopra, Sudarsana Kalluru,
Rajesh Borundia, Sony Chacko, Artum Zolotushko, Harish Patil, Rasesh Mody,
Sergey Ukhterov and Elad Manela, as well as former team members,
Eilon Greenstein and Shmulik Ravid.
Changes from previos version:
-----------------------------
From Version 7:
- Various small fixes according to Dave's suggestions; Largest change
[code-wise] - don't use tabs for indenting function arguments.
From Version 6:
- Reduced the number of arguments for functions with exceptionally
high number of parameters.
From Version 5:
- Style change and fixes [mostly in 1, 4 and 7].
Thanks go to Francois Romieu, a mere mortal. ;-)
From Version 4:
- Drop dependency for x86_64.
From Version 3:
- Limit support of initial submission to x86_64.
- Fix endian problems appearing via sparse [although no BE support yet].
- Fix small issues suggested by the kbuild test robot.
From Version 2:
- Removed U64_{HI,LO}; Using {upper,lower}_32_bits instead.
- Use regular napi weight definition.
- [We still use the __le variants for variables, since we didn't get
a reply regarding the change into non-user API types].
From Version 1:
- Removed private license file; Instead revised comments at source headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 26 Oct 2015 09:02:33 +0000 (11:02 +0200)]
qed: Add statistics support
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:31 +0000 (11:02 +0200)]
qed: Add link support
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:29 +0000 (11:02 +0200)]
qede: Add basic network device support
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 26 Oct 2015 09:02:28 +0000 (11:02 +0200)]
qed: Add slowpath L2 support
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:27 +0000 (11:02 +0200)]
qede: Add basic Network driver
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:26 +0000 (11:02 +0200)]
qed: Add basic L2 interface
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 26 Oct 2015 09:02:25 +0000 (11:02 +0200)]
qed: Add module with basic common support
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
I remember this warning and we had a similar issue when using workqueues
and calling netif_rx. See commit 5ff3fec ("mac802154: fix NOHZ
local_softirq_pending 08 warning").
This warning occurs when calling "netif_rx" inside the wrong context
(non softirq context). The net core api offers "netif_rx_ni" to call
netif_rx inside the correct softirq context.
Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Adding IPv6 for the TSO helper API is trivial:
* Don't play with the id (which doesn't exist in IPv6)
* Correctly update the payload_len (don't include the
length of the IP header itself)
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 27 Oct 2015 05:16:02 +0000 (22:16 -0700)]
Merge tag 'arcnet-for-4.4-rc1' of git://git.pengutronix.de/git/mgr/linux
Michael Grzeschik says:
====================
This series includes code simplifaction. The main changes are the correct
xceiver handling (enable/disable) of the com20020 cards. The driver now handles
link status change detection. The EAE PCI-ARCNET cards now make use of the
rotary encoded subdevice indexing and got support for led triggers on transmit
and reconnection events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuba Pawlak [Mon, 26 Oct 2015 16:17:14 +0000 (16:17 +0000)]
Bluetooth: Fix crash on fast disconnect of SCO
Fix a crash that may happen when a connection is closed before it was fully
established. Mapping conn->hcon was released by shutdown function, but it
is still referenced in (not yet finished) connection established handling
function.
exported perf symbols are GPL only, mark eBPF helper functions
used in tracing as GPL only as well.
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix safety checks for bpf_perf_event_read():
- only non-inherited events can be added to perf_event_array map
(do this check statically at map insertion time)
- dynamically check that event is local and !pmu->count
Otherwise buggy bpf program can cause kernel splat.
Also fix error path after perf_event_attrs()
and remove redundant 'extern'.
Fixes: 35578d798400 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Cuissard [Mon, 26 Oct 2015 09:27:39 +0000 (10:27 +0100)]
NFC: nfcmrvl: add firmware download support
Implement firmware download protocol for Marvell NFC controllers.
This protocol is based on NCI frames that's why parts of its
implementation use some NCI generic functions.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: st21nfca: Add support for proprietary commands
Add support for proprietary commands useful mainly
for factory testings.
Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where no
secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry as
for example RF trimmings or low level drivers configurations
(I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_LOAD: Allow to load a firmware into the CLF. A complete
packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: netlink: Add mode parameter to deactivate_target functions
In order to manage in a better way the nci poll mode state machine,
add mode parameter to deactivate_target functions.
This way we can manage different target state.
mode parameter make sense only in nci core.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for proprietary commands useful mainly for
factory testings. Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where
no secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry
like for example RF trimmings or low level drivers
configurations (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF.
A complete packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
- HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied
on the CLF antenna. A value between 0 and 0x0f is returned. 0 is
maximum.
- HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode.
It is a specific CLF command as there is no GPIO for this.
- HCI_DM_FWUPD_END: Allow to complete firmware update.
- HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied
on the CLF antenna to a reference value.
- MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data
received during a NCI_CORE_INIT_CMD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Florian Fainelli [Fri, 23 Oct 2015 19:11:08 +0000 (12:11 -0700)]
net: dsa: bcm_sf2: Unhardcode port numbers
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Oct 2015 18:38:07 +0000 (11:38 -0700)]
net: dsa: bcm_sf2: Implement FDB operations
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8xxxu.c:5786:32: warning: ‘rtl8192cu_fops’ defined but not used [-Wunused-variable]
Fix it by adding temporary ifdefs around the static functions.
Fixes: 033695bdf6d7 ("rtl8xxxu: move devices supported by rtlwifi under UNTESTED config") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The arcnet device has no interrupt to detect if the link has changed
from disconnected to connected. This patch adds an timer to toggle the
link detection. The timer will get retriggered as long as the
reconnection interrupts accure. If the recon interrupts hold off
for >1s we define the connection stable again.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has special leds on the the main io pci resource
bar. This patch adds support to trigger the conflict and data leds with
the packages.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
The EAE PLX-PCI card has a special rotary encoder
to configure the address of every card individually.
We take this information for the initial setup of
the cards dev_id.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
arcnet: com20020: add enable and disable device on open/close
This patch changes the driver to properly work with the linux netif
interface. The controller gets enabled on open and disabled on close.
Therefor it removes every bogus start of the xceiver. It only gets
enabled on com20020_open and disabled on com20020_close.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Marcel Holtmann [Sun, 25 Oct 2015 21:45:53 +0000 (22:45 +0100)]
Bluetooth: Rename bt_cb()->req into bt_cb()->hci
The SKB context buffer for HCI request is really not just for requests,
information in their are preserved for the whole HCI layer. So it makes
more sense to actually rename it into bt_cb()->hci and also call it then
struct hci_ctrl.
In addition that allows moving the decoded opcode for outgoing packets
into that struct. So far it was just consuming valuable space from the
main shared items. And opcode are not valid for L2CAP packets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST21NFCA_DM_GETINFO(ST21NFCA_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: st21nfca: Keep st21nfca_gates unchanged in load_session
We need to keep initial st_nci_gates values in order for
nfc_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st21nfca_gates was causing nfc_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: st-nci: Keep st_nci_gates unchanged in load_session
We need to keep initial st_nci_gates values in order for
nci_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st_nci_gates was causing nci_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: nci: Create pipe on specific gate in nci_hci_connect_gate
Some gates might need to have their pipes explicitly created.
Add a call to nci_hci_create_pipe in nci_hci_connect_gate for
every gate that is different than NCI_HCI_LINK_MGMT_GATE or
NCI_HCI_ADMIN_GATE.
In case of an error when opening a pipe, like in hci layer,
delete the pipe if it was created.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
projects / karo-tx-linux.git / log