Stefan Agner [Mon, 27 Oct 2014 16:40:44 +0000 (17:40 +0100)]
ARM: imx: clk-vf610: define PLL's clock tree
So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).
However, since commit dc4805c2e78ba5a22ea1632f3e3e4ee601a1743b
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.
This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Linus Torvalds [Tue, 4 Nov 2014 05:06:22 +0000 (21:06 -0800)]
Merge tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
"This kernel cycle has been calm for both pin control and GPIO so far
but here are three pin control patches for you anyway, only really
dealing with Baytrail:
- Two fixes for the Baytrail driver affecting IRQs and output state
in sysfs
- Use the linux-gpio mailing list also for pinctrl patches"
* tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: baytrail: show output gpio state correctly on Intel Baytrail
pinctrl: use linux-gpio mailing list
pinctrl: baytrail: Clear DIRECT_IRQ bit
Linus Torvalds [Tue, 4 Nov 2014 05:01:04 +0000 (21:01 -0800)]
Merge branch 'fixes-for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This contains important fixes for recently introduced highmem support
for default contiguous memory region used for dma-mapping subsystem"
* 'fixes-for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
mm, cma: make parameters order consistent in func declaration and definition
mm: cma: Use %pa to print physical addresses
mm: cma: Ensure that reservations never cross the low/high mem boundary
mm: cma: Always consider a 0 base address reservation as dynamic
mm: cma: Don't crash on allocation if CMA area can't be activated
Peter Chen [Tue, 4 Nov 2014 03:14:31 +0000 (11:14 +0800)]
usb: core: notify disconnection when core detects disconnect
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Tony Zheng [Fri, 17 Oct 2014 11:43:02 +0000 (19:43 +0800)]
usb: core: need to call usb_phy_notify_connect after device setup
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org> Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Mon, 27 Oct 2014 13:53:29 +0000 (14:53 +0100)]
xhci: no switching back on non-ULT Haswell
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Adel Gadllah [Thu, 9 Oct 2014 07:29:29 +0000 (09:29 +0200)]
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Mark Einon [Sun, 19 Oct 2014 19:25:26 +0000 (20:25 +0100)]
MAINTAINERS: Remove duplicate entry for usbip driver
The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file
still has the old staging entry as well as the new one. Remove the old entry.
Signed-off-by: Mark Einon <mark.einon@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luis Henriques [Wed, 1 Oct 2014 23:10:57 +0000 (00:10 +0100)]
usb: storage: fix build warnings !CONFIG_PM
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: Remove references to non-existent PLAT_S5P symbol
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde96
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Hans de Goede [Tue, 28 Oct 2014 10:05:29 +0000 (11:05 +0100)]
xhci: Disable streams on Asmedia 1042 xhci controllers
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Alan Stern [Fri, 31 Oct 2014 18:49:47 +0000 (14:49 -0400)]
usb-storage: handle a skipped data phase
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by: Paul Osmialowski <newchief@king.net.pl> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Wed, 1 Oct 2014 09:29:14 +0000 (11:29 +0200)]
usb: Do not allow usb_alloc_streams on unconfigured devices
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Paris [Thu, 30 Oct 2014 15:04:47 +0000 (11:04 -0400)]
cdc-acm: ensure that termios get set when the port is activated
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com> Reviewed-by: Johan Hovold <johan@kernel.org> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 3 Nov 2014 23:04:26 +0000 (15:04 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fixes from Sage Weil:
"There is a GFP flag fix from Mike Christie, an error code fix from
Jan, and fixes for two unnecessary allocations (kmalloc and workqueue)
from Ilya. All are well tested.
Ilya has one other fix on the way but it didn't get tested in time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: eliminate unnecessary allocation in process_one_ticket()
rbd: Fix error recovery in rbd_obj_read_sync()
libceph: use memalloc flags for net IO
rbd: use a single workqueue for all devices
Linus Torvalds [Mon, 3 Nov 2014 22:07:05 +0000 (14:07 -0800)]
Merge tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
Fengguang Wu [Mon, 3 Nov 2014 19:43:32 +0000 (16:43 -0300)]
[media] sp2: sp2_init() can be static
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Running ftracetests on a box that mounted debugfs in two locations
made the ftracetests fail. This is because the tests uses a grep
of debugfs from the /proc/mounts file to find the debugfs mount
point, and then appends "/tracing" to that string to get the tracing
directory.
If the debugfs directory is mounted twice, then that grep will return
two answers and appending "/tracing" to a string with two lines will
not work.
Use "head -1" to only take the first mount point found.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
regulator: max77693: Fix use of uninitialized regulator config
Driver allocated on stack struct regulator_config but didn't initialize
it fully. Few fields (driver_data, ena_gpio) were left untouched. This
lead to using random ena_gpio values as GPIOs for max77693 regulators.
On occasion these values could match real GPIO numbers leading to
interfering with other drivers and to unsuccessful enable/disable of
regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 80b022e29bfd ("regulator: max77693: Add max77693 regualtor driver.") Cc: <stable@vger.kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Ulrich Eckhardt [Fri, 10 Oct 2014 16:27:32 +0000 (13:27 -0300)]
[media] imon: fix other RC type protocol support
With kernel 3.17 the imon remote control for device 15c2:0034 does not
work anymore, which uses the OTHER protocol. Only the front panel
buttons which uses the RC6 protocol are working.
thermal: exynos: fix IRQ clearing on TMU initialization
* Factor out code for clearing raised IRQs from exynos_tmu_work() to
exynos_tmu_clear_irqs().
* Add a comment about documentation bugs to exynos_tmu_clear_irqs().
[ The documentation for Exynos3250, Exynos4412, Exynos5250 and
Exynos5260 incorrectly states that INTCLEAR register has
a different placing of bits responsible for FALL IRQs than
INTSTAT register. Exynos5420 and Exynos5440 documentation is
correct (Exynos4210 doesn't support FALL IRQs at all). ]
* Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead
of open-coded code trying to clear IRQs according to predefined
masks. After this change exynos_tmu_initialize() just clears
IRQs that are raised like it is already done in exynos_tmu_work().
As a nice side-effect the code now uses the correct offset
(16 instead of 12) for bits responsible for clearing FALL IRQs
in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250.
* Remove no longer needed intclr_rise_[mask,shift] and
intclr_fall_[mask,shift] fields from struct exynos_tmu_registers.
* Remove no longer needed defines.
This patch has been tested on Exynos4412 and Exynos5420 SoCs.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here on function return all temporarily used device nodes shall
decrement their usage counter. The problems are found with device
nodes allocated by for_each_child_of_node(), of_parse_phandle()
and of_find_node_by_name(), fix all problems at once.
thermal: exynos: Add support for TRIM_RELOAD feature at Exynos3250
This patch add support for TRIM_RELOAD feature at Exynos3250. The TMu of
Exynos3250 has two TRIMINFO_CON register and must need to set RELOAD bit
before reading TRIMINFO register.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: Amit Daniel Kachhap <amit.daniel@samsung.com> Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal: exynos: Add support for many TRIMINFO_CTRL registers
This patch support many TRIMINFO_CTRL registers if specific Exynos SoC
has one more TRIMINFO_CTRL registers. Also this patch uses proper 'RELOAD'
shift/mask bit operation to set RELOAD feature instead of static value.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Zhang Rui <rui.zhang@intel.com> Cc: Eduardo Valentin <edubezval@gmail.com> Cc: Amit Daniel Kachhap <amit.daniel@samsung.com> Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal: samsung: Exynos5260 and Exynos5420 should not use TRIM_RELOAD flag
Currently these SoCs claim TRIM_RELOAD support but don't have
triminfo_ctrl register address defined in their struct
exynos_tmu_registers entries. This causes incorrect write of
value "1" to data->base + 0x00 address (which happens to be
TRIMINFO register). Additionally according to the documentation
that I have neither Exynos5260 nor Exynos5420 support/require
TRIM_RELOAD feature. Thus fix the aforementioned issue by
removing TMU_SUPPORT_TRIM_RELOAD flag for both Exynos5260 and
Exynos5420.
thermal: exynos: cache non_hw_trigger_levels in pdata
Cache number of non-hardware trigger levels in a new pdata field
(non_hw_trigger_levels) and convert code in exynos_tmu_initialize()
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal: exynos: simplify temp_to_code() and code_to_temp()
* Remove dead temp check from temp_to_code() (this function users
in exynos_tmu_initialize() always pass correct temperatures and
exynos_tmu_set_emulation() returns early for EXYNOS4210 because
TMU_SUPPORT_EMULATION flag is not set on this SoC).
* Move temp_code check from code_to_temp() to exynos_tmu_read()
(code_to_temp() only user).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal: exynos: remove redundant threshold_code checks from exynos_tmu_initialize()
Remove runtime checks for negative return values of temp_to_code()
from exynos_tmu_initialize().
The current level temperature data hardcoded in pdata will never
cause a negative temp_to_code() return values and checking itself
is not proper. The checks in question are done at runtime in
a production code for data that is hardcoded inside driver during
development time and later it doesn't change. Such data should
be verified during development and review time (i.e. by a script
parsing relevant data from exynos_tmu_data.c, one can also argue
that verification to be done is so simple that the review by
a maintainer should be enough).
Theres should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal: exynos: remove redundant pdata checks from exynos_tmu_initialize()
Remove runtime checks for pdata sanity from exynos_tmu_initialize().
The current values hardcoded in pdata will never trigger the checks
and checking itself is not proper. The checks in question are done
at runtime in a production code for data that is hardcoded inside
driver during development time and later it doesn't change. Such
data should be verified during development and review time (i.e. by
a script parsing relevant data from exynos_tmu_data.c, one can also
argue that verification to be done is so simple that the review by
a maintainer should be enough).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal: exynos: remove dead code for HW_MODE calibration
The commit 1928457 ("thermal: exynos: Add hardware mode thermal
calibration support") has added HW_MODE feature but it has never
been enabled. As such it has been a dead code for over a year
now and should be removed from the kernel.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove unused / write-only entries from struct exynos_tmu_registers.
Then remove unused defines while at it.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Linus Torvalds [Sun, 2 Nov 2014 22:45:52 +0000 (14:45 -0800)]
Merge tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
Linus Torvalds [Sun, 2 Nov 2014 22:39:35 +0000 (14:39 -0800)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
Linus Torvalds [Sun, 2 Nov 2014 22:27:30 +0000 (14:27 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
Olof Johansson [Sun, 2 Nov 2014 21:36:05 +0000 (13:36 -0800)]
Merge tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.18-rc2" from Tony Lindgren:
Few fixes for omaps to enable NAND BCH so devices won't
produce errors when booted with omap2plus_defconfig, and
reduce bloat by making IPV6 a loadable module.
Also let's add a warning about legacy boot being deprecated
for omap3.
We now have things working with device tree, and only omap3 is
still booting in legacy mode. So hopefully this warning will
help move the remaining legacy mode users to boot with device
tree.
As the total reduction of code and static data is somewhere
around 20000 lines of code once we remove omap3 legacy mode
booting, we really do want to make omap3 to boot also in
device tree mode only over the next few merge cycles.
* tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (407 commits)
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
+ Linux 3.18-rc2
Linus Torvalds [Sun, 2 Nov 2014 20:56:20 +0000 (12:56 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
Linus Torvalds [Sun, 2 Nov 2014 20:31:02 +0000 (12:31 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
Dave Airlie [Sun, 2 Nov 2014 19:23:17 +0000 (05:23 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
Linus Torvalds [Sun, 2 Nov 2014 18:28:43 +0000 (10:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"A bunch of assorted fixes, most of them followups to overlayfs merge"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: initialize ->is_cursor
Return short read or 0 at end of a raw device, not EIO
isofs: don't bother with ->d_op for normal case
isofs_cmp(): we'll never see a dentry for . or ..
overlayfs: fix lockdep misannotation
ovl: fix check for cursor
overlayfs: barriers for opening upper-layer directory
rcu: Provide counterpart to rcu_dereference() for non-RCU situations
staging: android: logger: Fix log corruption regression
Linus Torvalds [Sun, 2 Nov 2014 18:20:26 +0000 (10:20 -0800)]
irda: stop calling sk_prot->disconnect() on connection failure
The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer. And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.
So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:56 +0000 (14:31 +0200)]
drm/exynos: correct connector->dpms field before resuming
During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:55 +0000 (14:31 +0200)]
drm/exynos: enable vblank after DPMS on
Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Andrzej Hajda [Fri, 10 Oct 2014 12:31:54 +0000 (14:31 +0200)]
drm/exynos: init kms poll at the end of initialization
HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Jan Kiszka [Wed, 8 Oct 2014 16:05:39 +0000 (18:05 +0200)]
KVM: nVMX: Disable preemption while reading from shadow VMCS
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Mon, 27 Oct 2014 22:03:43 +0000 (00:03 +0200)]
KVM: x86: Fix far-jump to non-canonical check
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In both Armada-375 and Armada-38x MPIC interrupts should be identified by
reading cause register multiplied by the interrupt mask.
A lack of above mentioned multiplication resulted in a bug, caused by the
fact that in Armada-375 and Armada-38x some of the interrupts
(e.g. network interrupts) can be handled either as a GIC or MPIC interrupts.
Therefore during MPIC interrupts handling, cause register shows hits from
interrupts even if they are masked for MPIC but unmasked for a GIC.
This resulted in 'bad IRQ' error, because masked MPIC interrupt without
registered interrupt handler, was trying to be handled during interrupt
handling procedure of some other unmasked MPIC interrupt (e.g. local timer
irq).
This commit fixes that by ensuring that during MPIC interrupt handling only
interrupts that are unmasked for MPIC are processed.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: bc69b8adfe22 ("irqchip: armada-370-xp: Setup a chained handler for the MPIC") Cc: <stable@vger.kernel.org> # v3.15+ Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Link: https://lkml.kernel.org/r/1411643839-64925-3-git-send-email-jaz@semihalf.com Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Dan Streetman [Fri, 31 Oct 2014 19:41:34 +0000 (15:41 -0400)]
powerpc: use device_online/offline() instead of cpu_up/down()
In powerpc pseries platform dlpar operations, use device_online() and
device_offline() instead of cpu_up() and cpu_down().
Calling cpu_up/down() directly does not update the cpu device offline
field, which is used to online/offline a cpu from sysfs. Calling
device_online/offline() instead keeps the sysfs cpu online value
correct. The hotplug lock, which is required to be held when calling
device_online/offline(), is already held when dlpar_online/offline_cpu()
are called, since they are called only from cpu_probe|release_store().
This patch fixes errors on phyp (PowerVM) systems that have cpu(s)
added/removed using dlpar operations; without this patch, the
/sys/devices/system/cpu/cpuN/online nodes do not correctly show the
online state of added/removed cpus.
Signed-off-by: Dan Streetman <ddstreet@ieee.org> Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com> Fixes: 0902a9044fa5 ("Driver core: Use generic offline/online for CPU offline/online") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Airlie [Sat, 1 Nov 2014 23:23:31 +0000 (09:23 +1000)]
Merge branch 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux
A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
(welcome Sinclair!)
and a fix for an incorrect hash key computation from me that is
completely harmless, but can wait 'til the next merge window if necessary.
(I can't really bother stable with this one).
* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
Linus Torvalds [Sat, 1 Nov 2014 22:11:27 +0000 (15:11 -0700)]
Merge tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some staging driver fixes for 3.18-rc3. Mostly iio and
comedi driver fixes for issues reported by people.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: fix memory leak / bad pointer freeing for chanlist
staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
staging: comedi: widen subdevice number argument in ioctl handlers
staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sat, 1 Nov 2014 22:08:04 +0000 (15:08 -0700)]
Merge tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.18-rc3.
Mostly usb-serial device ids and gadget fixes for issues that have
been reported. Full details are in the shortlog.
All of these have been in linux-next for a while"
* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: chipidea: Fix oops when removing the ci_hdrc module
usb: gadget: function: Fixed the return value on error path
usb: dwc2: gadget: disable phy before turning off power regulators
usb: gadget: function: Remove redundant usb_free_all_descriptors
usb: dwc3: gadget: Properly initialize LINK TRB
usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
usb: dwc2: Bits in bitfield should add up to 32
usb: dwc2: gadget: sparse warning of context imbalance
usb: gadget: udc: core: fix kernel oops with soft-connect
usb: musb: musb_dsps: fix NULL pointer in suspend
usb: musb: dsps: start OTG timer on resume again
usb: gadget: loopback: don't queue requests to bogus endpoints
usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
usb: gadget: f_fs: remove redundant ffs_data_get()
usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
usb: gadget: composite: enable BESL support
usb: musb: cppi41: restart hrtimer only if not yet done
usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
usb: serial: ftdi_sio: add "bricked" FTDI device PID
...
Linus Torvalds [Sat, 1 Nov 2014 17:41:26 +0000 (10:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Filipe is nailing down some problems with our skinny extent variation,
and Dave's patch fixes endian problems in the new super block checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
Btrfs: properly clean up btrfs_end_io_wq_cache
Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
btrfs: use macro accessors in superblock validation checks
Linus Torvalds [Sat, 1 Nov 2014 02:51:11 +0000 (19:51 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Linus Torvalds [Sat, 1 Nov 2014 02:08:25 +0000 (19:08 -0700)]
Merge tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes received after my previous pull request plus one that
has been in the works for quite a while, but its previous version
caused problems to happen, so it's been deferred till now.
Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
ACPI EC regression introduced in 3.17, system suspend error code path
regression introduced in 3.15, an older bug related to recovery from
failing resume from hibernation and a cpufreq-dt driver issue related
to operation performance points.
Specifics:
- Fix a crash on r8a7791/koelsch during resume from system suspend
caused by a recent cpufreq-dt commit (Geert Uytterhoeven).
- Fix an MFD enumeration problem introduced by a recent commit adding
ACPI support to the MFD subsystem that exposed a weakness in the
ACPI core causing ACPI enumeration to be applied to all devices
associated with one ACPI companion object, although it should be
used for one of them only (Mika Westerberg).
- Fix an ACPI EC regression introduced during the 3.17 cycle causing
some Samsung laptops to misbehave as a result of a workaround
targeted at some Acer machines. That includes a revert of a commit
that went too far and a quirk for the Acer machines in question.
From Lv Zheng.
- Fix a regression in the system suspend error code path introduced
during the 3.15 cycle that causes it to fail to take errors from
asychronous execution of "late" suspend callbacks into account
(Imre Deak).
- Fix a long-standing bug in the hibernation resume error code path
that fails to roll back everything correcty on "freeze" callback
errors and leaves some devices in a "suspended" state causing more
breakage to happen subsequently (Imre Deak).
- Make the cpufreq-dt driver disable operation performance points
that are not supported by the VR connected to the CPU voltage plane
with acceptable tolerance instead of constantly failing voltage
scaling later on (Lucas Stach)"
* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
ACPI: Use ACPI companion to match only the first physical device
cpufreq: cpufreq-dt: disable unsupported OPPs
An unintentional sysfs filename change in commit 5136b2da770d
("PCI: convert bus code to use dev_groups"), which appeared in
v3.13, changed "enable" to "enabled", and this changes it back.
Old users of "enable" are currently broken and will be helped by
this change. Anything that started to use "enabled" after v3.13
will be broken by this change. If necessary, we can add a symlink
to make both work, but this patch doesn't do that.
A mistaken duplicate merge that added a check twice. Nothing's
broken; this just removes the unnecessary code.
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"
* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Rename sysfs 'enabled' file back to 'enable'
PCI: imx6: Wait for clocks to stabilize after ref_en
Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
Andy Lutomirski [Sat, 1 Nov 2014 01:08:45 +0000 (18:08 -0700)]
x86_64, entry: Fix out of bounds read on sysenter
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code
reads out of bounds, causing the NT fix to be unreliable. But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.
That read is deterministically above the top of the stack. I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.
Fixes: 8c7aa698baca ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by: Rusty Russell <rusty@ozlabs.org> Cc: stable@vger.kernel.org Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 31 Oct 2014 23:22:29 +0000 (16:22 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"A set of miscellaneous ext4 bug fixes for 3.18"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: make ext4_ext_convert_to_initialized() return proper number of blocks
ext4: bail early when clearing inode journal flag fails
ext4: bail out from make_indexed_dir() on first error
jbd2: use a better hash function for the revoke table
ext4: prevent bugon on race between write/fcntl
ext4: remove extent status procfs files if journal load fails
ext4: disallow changing journal_csum option during remount
ext4: enable journal checksum when metadata checksum feature enabled
ext4: fix oops when loading block bitmap failed
ext4: fix overflow when updating superblock backups after resize
Linus Torvalds [Fri, 31 Oct 2014 23:18:47 +0000 (16:18 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota and ext3 fixes from Jan Kara.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs, jbd: use a more generic hash function
quota: Properly return errors from dquot_writeback_dquots()
ext3: Don't check quota format when there are no quota files
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
Pull sparc update from David Miller:
"Two changes:
1) It makes no sense to execute a VTOC partition table request in the
Sun virtual block device driver and fail to load if it doesn't
succeed because a) we don't use the result at all and b) it won't
succeed if there is an EFI partition on the disk, for example.
We read the partition table via the normal means in the block layer
anyways, so this is really completely useless, so just remove it.
From Dwight Engen.
2) Hook up new bpf system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: don't call VD_OP_GET_VTOC
sparc: Hook up bpf system call.
Linus Torvalds [Fri, 31 Oct 2014 21:43:42 +0000 (14:43 -0700)]
Merge tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze updates from Michal Simek:
- wire-up new bpf syscall
- fix PCI bug
- fix Kconfig warning
* tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire up bpf syscall
microblaze: Fix IO space breakage after of_pci_range_to_resource() change
microblaze: Fix missing NR_CPUS in menuconfig
Linus Torvalds [Fri, 31 Oct 2014 21:30:16 +0000 (14:30 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fixes from all around the place:
- hyper-V 32-bit PAE guest kernel fix
- two IRQ allocation fixes on certain x86 boards
- intel-mid boot crash fix
- intel-quark quirk
- /proc/interrupts duplicate irq chip name fix
- cma boot crash fix
- syscall audit fix
- boot crash fix with certain TSC configurations (seen on Qemu)
- smpboot.c build warning fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE
ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi()
x86, intel-mid: Create IRQs for APB timers and RTC timers
x86: Don't enable F00F workaround on Intel Quark processors
x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts
x86, cma: Reserve DMA contiguous area after initmem_init()
i386/audit: stop scribbling on the stack frame
x86, apic: Handle a bad TSC more gracefully
x86: ACPI: Do not translate GSI number if IOAPIC is disabled
x86/smpboot: Move data structure to its primary usage scope
* acpi-scan:
ACPI: Use ACPI companion to match only the first physical device
* acpi-ec:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
Linus Torvalds [Fri, 31 Oct 2014 21:05:35 +0000 (14:05 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various scheduler fixes all over the place: three SCHED_DL fixes,
three sched/numa fixes, two generic race fixes and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/dl: Fix preemption checks
sched: Update comments for CLONE_NEWNS
sched: stop the unbound recursion in preempt_schedule_context()
sched/fair: Fix division by zero sysctl_numa_balancing_scan_size
sched/fair: Care divide error in update_task_scan_period()
sched/numa: Fix unsafe get_task_struct() in task_numa_assign()
sched/deadline: Fix races between rt_mutex_setprio() and dl_task_timer()
sched/deadline: Don't replenish from a !SCHED_DEADLINE entity
sched: Fix race between task_group and sched_task_group
Linus Torvalds [Fri, 31 Oct 2014 21:01:47 +0000 (14:01 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus on the kernel side:
- a revert for a newly introduced PMU driver which isn't complete yet
and where we ran out of time with fixes (to be tried again in
v3.19) - this makes up for a large chunk of the diffstat.
- compilation warning fixes
- a printk message fix
- event_idx usage fixes/cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Trivial typo fix for --demangle
perf tools: Fix report -F dso_from for data without branch info
perf tools: Fix report -F dso_to for data without branch info
perf tools: Fix report -F symbol_from for data without branch info
perf tools: Fix report -F symbol_to for data without branch info
perf tools: Fix report -F mispredict for data without branch info
perf tools: Fix report -F in_tx for data without branch info
perf tools: Fix report -F abort for data without branch info
perf tools: Make CPUINFO_PROC an array to support different kernel versions
perf callchain: Use global caching provided by libunwind
perf/x86/intel: Revert incomplete and undocumented Broadwell client support
perf/x86: Fix compile warnings for intel_uncore
perf: Fix typos in sample code in the perf_event.h header
perf: Fix and clean up initialization of pmu::event_idx
perf: Fix bogus kernel printk
perf diff: Add missing hists__init() call at tool start
Linus Torvalds [Fri, 31 Oct 2014 20:57:45 +0000 (13:57 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull futex fixes from Ingo Molnar:
"This contains two futex fixes: one fixes a race condition, the other
clarifies shared/private futex comments"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix a race condition between REQUEUE_PI and task death
futex: Mention key referencing differences between shared and private futexes
Ilya Dryomov [Wed, 22 Oct 2014 14:15:37 +0000 (18:15 +0400)]
libceph: eliminate unnecessary allocation in process_one_ticket()
Commit c27a3e4d667f ("libceph: do not hard code max auth ticket len")
while fixing a buffer overlow tried to keep the same as much of the
surrounding code as possible and introduced an unnecessary kmalloc() in
the unencrypted ticket path. It is likely to fail on huge tickets, so
get rid of it.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com> Reviewed-by: Sage Weil <sage@redhat.com>
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 31 Oct 2014 17:38:52 +0000 (13:38 -0400)]
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>