scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()
The BUG_ON() recently introduced in lpfc_sli_ringtxcmpl_put() is hit in
the lpfc_els_abort() > lpfc_sli_issue_abort_iotag() >
lpfc_sli_abort_iotag_issue() function path [similar names], due to
'piocb->vport == NULL':
BUG_ON(!piocb || !piocb->vport);
This happens because lpfc_sli_abort_iotag_issue() doesn't set the
'abtsiocbp->vport' pointer -- but this is not the problem.
Previously, lpfc_sli_ringtxcmpl_put() accessed 'piocb->vport' only if
'piocb->iocb.ulpCommand' is neither CMD_ABORT_XRI_CN nor
CMD_CLOSE_XRI_CN, which are the only possible values for
lpfc_sli_abort_iotag_issue():
So, this function path would not have hit this possible NULL pointer
dereference before.
In order to fix this regression, move the second part of the BUG_ON()
check prior to the pointer dereference that it does check for.
For reference, this is the stack trace observed. The problem happened
because an unsolicited event was received - a PLOGI was received after
our PLOGI was issued but not yet complete, so the discovery state
machine goes on to sw-abort our PLOGI.
Dan Carpenter [Fri, 18 Nov 2016 11:53:39 +0000 (14:53 +0300)]
scsi: be2iscsi: allocate enough memory in beiscsi_boot_get_sinfo()
We accidentally allocate sizeof(u32) instead of sizeof(struct
be_cmd_get_session_resp).
Fixes: 50a4b824be9e ("scsi: be2iscsi: Fix to make boot discovery non-blocking") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Suganath Prabu S [Thu, 17 Nov 2016 10:45:58 +0000 (16:15 +0530)]
scsi: mpt3sas: Unblock device after controller reset
While issuing any ATA passthrough command to firmware the driver will
block the device. But it will unblock the device only if the I/O
completes through the ISR path. If a controller reset occurs before
command completion the device will remain in blocked state.
Make sure we unblock the device following a controller reset if an ATA
passthrough command was queued.
[mkp: clarified patch description]
Cc: <stable@vger.kernel.org> # v4.4+ Fixes: ac6c2a93bd07 ("mpt3sas: Fix for SATA drive in blocked state, after diag reset") Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Thu, 17 Nov 2016 11:15:56 +0000 (12:15 +0100)]
scsi: hpsa: use bus '3' for legacy HBA devices
Older controllers use SCSI target id '0' for the first internal disk. As
the controllers are now placed on the same bus as the internal disks
this leads to a clash with the SCSI target id of controller. This patch
checks the SCSI revision, and moves older controller to bus '3' to be
compatible with older releases and avoid this problem.
[mkp: fixed uninitialized variable]
Fixes: 09371d623c9 ("hpsa: Change SAS transport devices to bus 0.") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 540eb1eef0ab ("scsi: libfc: fix seconds_since_last_reset calculation")
removed the use of 'struct timespec' from fc_get_host_stats(). This broke the
output of 'fcoeadm -s' after kernel 4.8-rc1.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: <stable@vger.kernel.org> # v4.8+ Fixes: 540eb1eef0ab ("scsi: libfc: fix seconds_since_last_reset calculation") Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: qla2xxx: do not abort all commands in the adapter during EEH recovery
The previous commit 1535aa75a3d8 ("qla2xxx: fix invalid DMA access after
command aborts in PCI device remove") introduced a regression during an
EEH recovery, since the change to the qla2x00_abort_all_cmds() function
calls qla2xxx_eh_abort(), which verifies the EEH recovery condition but
handles it heavy-handed. (commit a465537ad1a4 "qla2xxx: Disable the
adapter and skip error recovery in case of register disconnect.")
This problem warrants a more general/optimistic solution right into
qla2xxx_eh_abort() (eg in case a real command abort arrives during EEH
recovery, or if it takes long enough to trigger command aborts); but
it's still worth to add a check to ensure the code added by the previous
commit is correct and contained within its owner function.
This commit just adds a 'if (!ha->flags.eeh_busy)' check around it.
(ahem; a trivial fix for this -rc series; sorry for this oversight.)
With it applied, both PCI device remove and EEH recovery works fine.
Fixes: 1535aa75a3d8 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove") Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming
secure erase. Due to the very long time the operation takes, commands
issued during the erase will time out and will trigger execution of the
abort hook. Even though the abort hook is called for the specific
command which timed out, this leads to entire device halt
(scsi_state terminated) and premature termination of the secure erase.
Set device state to busy while ATA passthrough commands are in progress.
[mkp: hand applied to 4.9/scsi-fixes, tweaked patch description]
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com> Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Cc: <linux-scsi@vger.kernel.org> Cc: Sathya Prakash <sathya.prakash@broadcom.com> Cc: Chaitra P B <chaitra.basappa@broadcom.com> Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com> Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com> Cc: Hannes Reinecke <hare@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sumit Saxena [Wed, 9 Nov 2016 10:59:42 +0000 (02:59 -0800)]
scsi: megaraid_sas: fix macro MEGASAS_IS_LOGICAL to avoid regression
This patch will fix regression caused by commit 1e793f6fc0db ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove
If a command is aborted in the kernel but not in the adapter, it might be
considered complete and its DMA memory released, but it is still alive in
the adapter, which will trigger an invalid DMA access upon its completion
(in the DMA operations to deliver the command response to the driver).
On powerpc platforms with IOMMU/EEH capabilities, the problem is observed
during PCI device removal with ongoing IO requests -- which might trigger
an EEH event very often, pointing to a 'TCE Request Page Access Error'.
In that path, which is qla2x00_remove_one(), the commands are aborted in
qla2x00_abort_all_cmds(), which does not perform an abort in the adapter
as is done in qla2xxx_eh_abort() for example.
So, this patch changes qla2x00_abort_all_cmds() to abort commands in the
adapter too, with a call to qla2xxx_eh_abort(), which already implements
all the logic to submit abort requests and handle responses.
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com> Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: qla2xxx: do not queue commands when unloading
When the driver is unloading, in qla2x00_remove_one(), there is a single
call/point in time to abort ongoing commands, qla2x00_abort_all_cmds(),
which is still several steps away from the call to scsi_remove_host().
If more commands continue to arrive and be processed during that
interval, when the driver is tearing down and releasing its structures,
it might potentially hit an oops due to invalid memory access:
Unable to handle kernel paging request for data at address 0x00000138
<...>
NIP [d000000004700a40] qla2xxx_queuecommand+0x80/0x3f0 [qla2xxx]
LR [d000000004700a10] qla2xxx_queuecommand+0x50/0x3f0 [qla2xxx]
So, fail commands in qla2xxx_queuecommand() if the UNLOADING bit is set.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before calling task_release_itt() task data is memset to zero because of
which DDP context information is lost resulting in incorrect DDP
resource cleanup, to fix this call task_release_itt() before memset.
Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bill Kuzeja [Fri, 21 Oct 2016 20:45:27 +0000 (16:45 -0400)]
scsi: qla2xxx: Fix scsi scan hang triggered if adapter fails during init
A system can get hung task timeouts if a qlogic board fails during
initialization (if the board breaks again or fails the init). The hang
involves the scsi scan.
In a nutshell, since commit beb9e315e6e0 ("qla2xxx: Prevent removal and
board_disable race"):
...it is possible to have freed ha (base_vha->hw) early by a call to
qla2x00_remove_one when pdev->enable_cnt equals zero:
if (!atomic_read(&pdev->enable_cnt)) {
scsi_host_put(base_vha->host);
kfree(ha);
pci_set_drvdata(pdev, NULL);
return;
Almost always, the scsi_host_put above frees the vha structure
(attached to the end of the Scsi_Host we're putting) since it's the last
put, and life is good. However, if we are entering this routine because
the adapter has broken sometime during initialization AND a scsi scan is
already in progress (and has done its own scsi_host_get), vha will not
be freed. What's worse, the scsi scan will access the freed ha structure
through qla2xxx_scan_finished:
if (time > vha->hw->loop_reset_delay * HZ)
return 1;
The scsi scan keeps checking to see if a scan is complete by calling
qla2xxx_scan_finished. There is a timeout value that limits the length
of time a scan can take (hw->loop_reset_delay, usually set to 5
seconds), but this definition is in the data structure (hw) that can get
freed early.
This can yield unpredictable results, the worst of which is that the
scsi scan can hang indefinitely. This happens when the freed structure
gets reused and loop_reset_delay gets overwritten with garbage, which
the scan obliviously uses as its timeout value.
The fix for this is simple: at the top of qla2xxx_scan_finished, check
for the UNLOADING bit in the vha structure (_vha is not freed at this
point). If UNLOADING is set, we exit the scan for this adapter
immediately. After this last reference to the ha structure, we'll exit
the scan for this adapter, and continue on.
This problem is hard to hit, but I have run into it doing negative
testing many times now (with a test specifically designed to bring it
out), so I can verify that this fix works. My testing has been against a
RHEL7 driver variant, but the bug and patch are equally relevant to to
the upstream driver.
Fixes: beb9e315e6e0 ("qla2xxx: Prevent removal and board_disable race") Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In other words, alua_rtpg_queue() must hold an sdev reference and a pg
reference before queueing rtpg work. If no rtpg work is queued no
additional references should be held when alua_rtpg_queue() returns. If
no rtpg work is queued, ensure that alua_rtpg_queue() only gives up the
sdev reference if that reference was obtained by the same
alua_rtpg_queue() call.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reported-by: Tang Junhui <tang.junhui@zte.com.cn> Cc: Hannes Reinecke <hare@suse.com> Cc: Tang Junhui <tang.junhui@zte.com.cn> Cc: <stable@vger.kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
David Jeffery [Fri, 28 Oct 2016 16:27:26 +0000 (12:27 -0400)]
scsi: vmw_pvscsi: return SUCCESS for successful command aborts
The vmw_pvscsi driver reports most successful aborts as FAILED to the
scsi error handler. This is do to a misunderstanding of how
completion_done() works and its interaction with a successful wait using
wait_for_completion_timeout(). The vmw_pvscsi driver is expecting
completion_done() to always return true if complete() has been called on
the completion structure. But completion_done() returns true after
complete() has been called only if no function like
wait_for_completion_timeout() has seen the completion and cleared it as
part of successfully waiting for the completion.
Instead of using completion_done(), vmw_pvscsi should just use the
return value from wait_for_completion_timeout() to know if the wait
timed out or not.
[mkp: bumped driver version per request]
Signed-off-by: David Jeffery <djeffery@redhat.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Acked-by: Jim Gill <jgill@vmware.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
That check should be for the line sas_target_priv_data->raid_device =
raid_device;
Due to above hunk, we are not initializing raid_device's starget for
raid volumes, and so during raid disk deletion driver is not calling
scsi_remove_target() API as driver observes starget field of
raid_device's structure as NULL.
tang.junhui [Fri, 28 Oct 2016 07:54:07 +0000 (15:54 +0800)]
scsi: scsi_dh_alua: fix missing kref_put() in alua_rtpg_work()
Reference count of pg leaks in alua_rtpg_work() since kref_put() is not
called to decrease the reference count of pg when the condition
pg->rtpg_sdev==NULL satisfied (actually it is easy to satisfy), it would
cause memory of pg leakage.
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn> Cc: <stable@vger.kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ching Huang [Wed, 19 Oct 2016 09:50:26 +0000 (17:50 +0800)]
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
The arcmsr driver failed to pass SYNCHRONIZE CACHE to controller
firmware. Depending on how drive caches are handled internally by
controller firmware this could potentially lead to data integrity
problems.
Ensure that cache flushes are passed to the controller.
[mkp: applied by hand and removed unused vars]
Cc: <stable@vger.kernel.org> Signed-off-by: Ching Huang <ching2048@areca.com.tw> Reported-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kashyap Desai [Fri, 21 Oct 2016 13:33:32 +0000 (06:33 -0700)]
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59 CC: stable@vger.kernel.org Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Tue, 11 Oct 2016 09:23:23 +0000 (11:23 +0200)]
scsi: NCR5380: no longer mark irq probing as __init
The g_NCR5380 has been converted to more regular probing, which
means its probe function can now be invoked after the __init section
is discarded, as pointed out by this kbuild warning:
WARNING: drivers/scsi/built-in.o(.text+0x3a105): Section mismatch in reference from the function generic_NCR5380_isa_match() to the function .init.text:probe_intr()
WARNING: drivers/scsi/built-in.o(.text+0x3a145): Section mismatch in reference from the function generic_NCR5380_isa_match() to the variable .init.data:probe_irq
To make sure this works correctly in all cases, let's remove
the __init and __initdata annotations.
Fixes: a8cfbcaec0c1 ("scsi: g_NCR5380: Stop using scsi_module.c") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk_timeout_work takes queue_lock spin_lock with interrupts disabled
before invoking iscsi_eh_cmd_timed_out. This causes a WARN_ON_ONCE in
spin_unlock_bh for wrb_lock/io_sgl_lock/mgmt_sgl_lock.
CPU was kept busy in lot of bottom half work with interrupts disabled
thus causing hard lock up.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jitendra Bhivare [Thu, 13 Oct 2016 06:38:48 +0000 (12:08 +0530)]
scsi: libiscsi: Fix locking in __iscsi_conn_send_pdu
The code at free_task label in __iscsi_conn_send_pdu can get executed
from blk_timeout_work which takes queue_lock using spin_lock_irq.
back_lock taken with spin_unlock_bh will cause WARN_ON_ONCE. The code
gets executed either with bottom half or IRQ disabled hence using
spin_lock/spin_unlock for back_lock is safe.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Sat, 15 Oct 2016 19:09:13 +0000 (12:09 -0700)]
Merge tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs
Pull befs fixes from Luis de Bethencourt:
"I recently took maintainership of the befs file system [0]. This is
the first time I send you a git pull request, so please let me know if
all the below is OK.
Salah Triki and myself have been cleaning the code and fixing a few
small bugs.
Sorry I couldn't send this sooner in the merge window, I was waiting
to have my GPG key signed by kernel members at ELCE in Berlin a few
days ago."
[0] https://lkml.org/lkml/2016/7/27/502
* tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs: (39 commits)
befs: befs: fix style issues in datastream.c
befs: improve documentation in datastream.c
befs: fix typos in datastream.c
befs: fix typos in btree.c
befs: fix style issues in super.c
befs: fix comment style
befs: add check for ag_shift in superblock
befs: dump inode_size superblock information
befs: remove unnecessary initialization
befs: fix typo in befs_sb_info
befs: add flags field to validate superblock state
befs: fix typo in befs_find_key
befs: remove unused BEFS_BT_PARMATCH
fs: befs: remove ret variable
fs: befs: remove in vain variable assignment
fs: befs: remove unnecessary *befs_sb variable
fs: befs: remove useless initialization to zero
fs: befs: remove in vain variable assignment
fs: befs: Insert NULL inode to dentry
fs: befs: Remove useless calls to brelse in befs_find_brun_dblindirect
...
Linus Torvalds [Sat, 15 Oct 2016 17:03:15 +0000 (10:03 -0700)]
Merge tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot
time as possible, hoping to capitalize on any possible variation in
CPU operation (due to runtime data differences, hardware differences,
SMP ordering, thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example
for how to manipulate kernel code using the gcc plugin internals"
* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Mark functions with __latent_entropy
gcc-plugins: Add latent_entropy plugin
Linus Torvalds [Sat, 15 Oct 2016 16:26:12 +0000 (09:26 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Linus Torvalds [Sat, 15 Oct 2016 16:20:54 +0000 (09:20 -0700)]
Merge tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial small fixes"
* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: line6: fix a crash in line6_hwdep_write()
ALSA: seq: fix passing wrong pointer in function call of compatibility layer
ALSA: hda - Fix a failure of micmute led when having multi adcs
ALSA: line6: Fix POD X3 Live audio input
Linus Torvalds [Sat, 15 Oct 2016 01:19:05 +0000 (18:19 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more misc uaccess and vfs updates from Al Viro:
"The rest of the stuff from -next (more uaccess work) + assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
score: traps: Add missing include file to fix build error
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
fs/super.c: fix race between freeze_super() and thaw_super()
overlayfs: Fix setting IOP_XATTR flag
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
blackfin: no access_ok() for __copy_{to,from}_user()
arm64: don't zero in __copy_from_user{,_inatomic}
arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
arc: don't leak bits of kernel stack into coredump
alpha: get rid of tail-zeroing in __copy_user()
Linus Torvalds [Sat, 15 Oct 2016 00:47:31 +0000 (17:47 -0700)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Including:
- nine bug fixes for stable. Some of these we found at the recent two
weeks of SMB3 test events/plugfests.
- significant improvements in reconnection (e.g. if server or network
crashes) especially when mounted with "persistenthandles" or to
server which advertises Continuous Availability on the share.
- a new mount option "idsfromsid" which improves POSIX compatibility
in some cases (when winbind not configured e.g.) by better (and
faster) fetching uid/gid from acl (when "cifsacl" mount option is
enabled). NB: we are almost complete work on "cifsacl" (querying
mode/uid/gid from ACL) for SMB3, but SMB3 support for cifsacl is
not included in this set.
- improved handling for SMB3 "credits" (even if server is buggy)
Still working on two sets of changes:
- cifsacl enablement for SMB3
- cleanup of RFC1001 length calculation (so we can handle encryption
and multichannel and RDMA)
And a couple of new bugs were reported recently (unrelated to above)
so will probably have another merge request next week"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
CIFS: Retrieve uid and gid from special sid if enabled
CIFS: Add new mount option to set owner uid and gid from special sids in acl
CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
CIFS: Fix persistent handles re-opening on reconnect
SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
SMB2: Separate Kerberos authentication from SMB2_sess_setup
Expose cifs module parameters in sysfs
Cleanup missing frees on some ioctls
Enable previous version support
Do not send SMB3 SET_INFO request if nothing is changing
SMB3: Add mount parameter to allow user to override max credits
fs/cifs: reopen persistent handles on reconnect
Clarify locking of cifs file and tcon structures and make more granular
Fix regression which breaks DFS mounting
fs/cifs: keep guid when assigning fid to fileinfo
SMB3: GUIDs should be constructed as random but valid uuids
Set previous session id correctly on SMB3 reconnect
cifs: Limit the overall credit acquired
Display number of credits available
Add way to query creation time of file via cifs xattr
...
Linus Torvalds [Sat, 15 Oct 2016 00:44:56 +0000 (17:44 -0700)]
Merge branch 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Some fixes from Omar and Dave Sterba for our new free space tree.
This isn't heavily used yet, but as we move toward making it the new
default we wanted to nail down an endian bug"
* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: tests: uninline member definitions in free_space_extent
btrfs: tests: constify free space extent specs
Btrfs: expand free space tree sanity tests to catch endianness bug
Btrfs: fix extent buffer bitmap tests on big-endian systems
Btrfs: catch invalid free space trees
Btrfs: fix mount -o clear_cache,space_cache=v2
Btrfs: fix free space tree bitmaps on big-endian systems
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
sb_wait_write()->percpu_rwsem_release() fools lockdep to avoid the
false-positives. Now that xfs was fixed by Dave's commit dbad7c993053
("xfs: stop holding ILOCK over filldir callbacks") we can remove it and
change freeze_super() and thaw_super() to run with s_writers.rw_sem locks
held; we add two trivial helpers for that, lockdep_sb_freeze_release()
and lockdep_sb_freeze_acquire().
xfstests-dev/check `grep -il freeze tests/*/???` does not trigger any
warning from lockdep.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 15 Oct 2016 00:23:33 +0000 (17:23 -0700)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This update contains fixes to the "use mounter's permission to access
underlying layers" area, and miscellaneous other fixes and cleanups.
No new features this time"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: use vfs_get_link()
vfs: add vfs_get_link() helper
ovl: use generic_readlink
ovl: explain error values when removing acl from workdir
ovl: Fix info leak in ovl_lookup_temp()
ovl: during copy up, switch to mounter's creds early
ovl: lookup: do getxattr with mounter's permission
ovl: copy_up_xattr(): use strnlen
fs/super.c: fix race between freeze_super() and thaw_super()
Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.
In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Vivek Goyal [Fri, 14 Oct 2016 01:03:36 +0000 (03:03 +0200)]
overlayfs: Fix setting IOP_XATTR flag
ovl_fill_super calls ovl_new_inode to create a root inode for the new
superblock before initializing sb->s_xattr. This wrongly causes
IOP_XATTR to be cleared in i_opflags of the new inode, causing SELinux
to log the following message:
SELinux: (dev overlay, type overlay) has no xattr support
Fix this by initializing sb->s_xattr and similar fields before calling
ovl_new_inode.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Vegard Nossum [Sat, 8 Oct 2016 09:18:07 +0000 (11:18 +0200)]
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
Both import_iovec() and rw_copy_check_uvector() take an array
(typically small and on-stack) which is used to hold an iovec array copy
from userspace. This is to avoid an expensive memory allocation in the
fast path (i.e. few iovec elements).
The caller may have to check whether these functions actually used
the provided buffer or allocated a new one -- but this differs between
the too. Let's just add a kernel doc to clarify what the semantics are
for each function.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 14 Oct 2016 22:17:12 +0000 (15:17 -0700)]
Merge tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"This update consists of:
- Fixes and improvements to existing tests
- Moving code from Documentation to selftests, samples, and tools:
* Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and
networking tests from Documentation to selftests.
* Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay,
and blackfin examples from Documentation to samples.
* Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
Documentation to tools.
* Deletes BUILD_DOCSRC and its dependencies"
* tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (21 commits)
selftests/futex: Check ANSI terminal color support
Doc: update 00-INDEX files to reflect the runnable code move
samples: move blackfin gptimers-example from Documentation
tools: move pcmcia crc32hash tool from Documentation
tools: move laptops dslm tool from Documentation
tools: move accounting tool from Documentation
samples: move auxdisplay example code from Documentation
samples: move watchdog example code from Documentation
samples: move timers example code from Documentation
samples: move misc-devices/mei example code from Documentation
samples: move mic/mpssd example code from Documentation
selftests: Move networking/timestamping from Documentation
selftests: move watchdog tests from Documentation/watchdog
selftests: move ia64 tests from Documentation/ia64
selftests: move vDSO tests from Documentation/vDSO
selftests: move ptp tests from Documentation/ptp
selftests: move prctl tests from Documentation/prctl
selftests: move dnotify_test from Documentation/filesystems
selftests/timers: Add missing error code assignment before test
selftests/zram: replace ZRAM_LZ4_COMPRESS
...
Linus Torvalds [Fri, 14 Oct 2016 22:03:08 +0000 (15:03 -0700)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"Just a few patches on the kbuild.git#misc branch this time:
- New Coccinelle patch by Nicholas Mc Guire
- Existing patch fixes by Julia Lawall
- Minor comment fix by Markus Elfring"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Coccinelle: flag conditions with no effect
scripts/coccicheck: Update reference for the corresponding documentation
Coccinelle: pm_runtime: ensure relevance of pm_runtime reports
Coccinelle: limit memdup_user transformation to GFP_KERNEL case
Linus Torvalds [Fri, 14 Oct 2016 21:26:58 +0000 (14:26 -0700)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
Linus Torvalds [Fri, 14 Oct 2016 21:11:22 +0000 (14:11 -0700)]
Merge tag 'docs-4.9-2' of git://git.lwn.net/linux
Pull one more documentation update from Jonathan Corbet:
"A single commit converting the mac80211 DocBook template over to
Sphinx. Only 32 more to go..."
* tag 'docs-4.9-2' of git://git.lwn.net/linux:
docs-rst: sphinxify 802.11 documentation
Linus Torvalds [Fri, 14 Oct 2016 20:43:08 +0000 (13:43 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma qedr RoCE driver from Doug Ledford:
"Early on in the merge window I mentioned I had a backlog of new
drivers waiting to be reviewed and that, in addition to the hns-roce
driver, I wanted to get possible a couple more reviewed. I ended up
only having the time to complete one of the additional drivers.
During Dave Miller's pull request this go around, there were a series
of 9 patches to the QLogic qed net driver that add basic support for a
paired RoCE driver. That support is currently not functional because
it is missing the matching RoCE driver in the RDMA subsystem. I
managed to finish that review. However, because it goes against part
of Dave's net pull, and a part that was accepted a day or two after
the merge window opened, to apply cleanly it has to be applied to
either the tip of Dave's net branch, or as I did in this case, I just
applied it to your master after you had taken Dave's pull request."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
qedr: Add events support and register IB device
qedr: Add GSI support
qedr: Add LL2 RoCE interface
qedr: Add support for data path
qedr: Add support for memory registeration verbs
qedr: Add support for QP verbs
qedr: Add support for PD,PKEY and CQ verbs
qedr: Add support for user context verbs
qedr: Add support for RoCE HW init
qedr: Add RoCE driver framework
Linus Torvalds [Fri, 14 Oct 2016 20:35:05 +0000 (13:35 -0700)]
Merge tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"This merge window was the first where Huawei had to try and coordinate
their patches between their net driver and their new roce driver
(similar to mlx4 and mlx5).
They didn't do horribly, but there were some issues (and we knew that
because they simply didn't know what to do in the beginning). As a
result, I had a set of patches that depended on some patches that
normally would have come to you via Dave's tree. Those patches have
been on netdev@ for a while, so I got Dave to give me his approval to
send them to you. As such, the other 29 patches I had behind them are
also now ready to go.
This catches the hns and hns-roce drivers up to current, and for
future patches we are working with them to get them up to speed on how
to do joint driver development so that they don't have these sorts of
cross tree dependency issues again. BTW, Dave gave me permission to
add his Acked-by: to the patches against the net tree, but I've had
this branch through 0day (but not linux-next since it was off by
itself) and I didn't want to rebase the series just to add Dave's ack
for the 8 patches in the net area.
Updates to the hns drivers:
- Small patch set for hns net driver that the roce patches depend on
- Various fixes to the hns-roce driver
- Add connection manager support to the hns-roce driver"
* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (36 commits)
IB/hns: Fix for removal of redundant code
IB/hns: Delete the redundant lines in hns_roce_v1_m_qp()
IB/hns: Fix the bug when platform_get_resource() exec fail
IB/hns: Update the rq head when modify qp state
IB/hns: Cq has not been freed
IB/hns: Validate mtu when modified qp
IB/hns: Some items of qpc need to take user param
IB/hns: The Ack timeout need a lower limit value
IB/hns: Return bad wr while post send failed
IB/hns: Fix bug of memory leakage for registering user mr
IB/hns: Modify the init of iboe lock
IB/hns: Optimize code of aeq and ceq interrupt handle and fix the bug of qpn
IB/hns: Delete the sqp_start from the structure hns_roce_caps
IB/hns: Fix bug of clear hem
IB/hns: Remove unused parameter named qp_type
IB/hns: Simplify function of pd alloc and qp alloc
IB/hns: Fix bug of using uninit refcount and free
IB/hns: Remove parameters of resize cq
IB/hns: Remove unused parameters in some functions
IB/hns: Add node_guid definition to the bindings document
...
Brian King [Thu, 13 Oct 2016 19:45:24 +0000 (14:45 -0500)]
scsi: ipr: Fix async error WARN_ON
Commit afc3f83cb4a5 ("scsi: ipr: Add asynchronous error notification")
introduced the warn on shown below. To fix this, rather than attempting
to send the KOBJ_CHANGE uevent from interrupt context, which is what is
causing the WARN_ON, just wake the ipr worker thread which will send a
KOBJ_CHANGE uevent.
Dan Carpenter [Fri, 14 Oct 2016 20:18:39 +0000 (16:18 -0400)]
scsi: zfcp: spin_lock_irqsave() is not nestable
We accidentally overwrite the original saved value of "flags" so that we
can't re-enable IRQs at the end of the function. Presumably this
function is mostly called with IRQs disabled or it would be obvious in
testing.
Fixes: aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)") Cc: <stable@vger.kernel.org> #2.6.38+ Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Fri, 14 Oct 2016 20:19:30 +0000 (13:19 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull some more input subsystem updates from Dmitry Torokhov:
"An update to the ALPS driver to support the V8 protocol with
touchstick, a change for i8042 to skip selftest on many Asus laptops
which helps to keep their touchpads working after resume, and a couple
other driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - skip selftest on ASUS laptops
Input: melfas_mip4 - add ic_name sysfs attribute
Input: melfas_mip4 - add maintainer information
Input: melfas_mip4 - add devicetree binding documentations
Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
Input: synaptics-rmi4 - fix error handling in I2C transport driver
Input: synaptics-rmi4 - fix error handling in SPI transport driver
Input: ALPS - add V8 protocol documentation
Input: ALPS - set DualPoint flag for 74 03 28 devices
Input: ALPS - allow touchsticks to report pressure
Input: ALPS - handle 0-pressure 1F events
Input: ALPS - add touchstick support for SS5 hardware
Input: elantech - force needed quirks on Fujitsu H760
Input: elantech - fix Lenovo version typo
Drivers:
- ac100: support clock-output-names
- cmos: properly handle ACPI alarms and quirky BIOSes and other fixes
- ds1307: fix century bit support while staying comaptible with
previous behaviour by default
- ds1347: switch to regmap
- isl12057 is now handled by ds1307
- omap: support external wakeup
- rv8803: allow to disable voltage drop detection"
* tag 'rtc-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (25 commits)
rtc: rv8803: set VDETOFF and SWOFF via device tree
dt/bindings: Add bindings for Micro Crystal rv8803
devicetree: Add Micro Crystal AG vendor id
rtc: cmos: avoid unused function warning
rtc: ac100: Add NULL checking for devm_kzalloc call
rtc: ds1347: changed raw spi calls to register map calls
rtc: cmos: Restore alarm after resume
rtc: cmos: Clear ACPI-driven alarms upon resume
rtc: omap: Support ext_wakeup configuration
rtc: cmos: Initialize hpet timer before irq is registered
rtc: asm9260: rework locking
rtc: asm9260: allow COMPILE_TEST
rtc: constify rtc_class_ops structures
rtc: ac100: support clock-output-names in device tree binding
rtc: rx6110: remove owner assignment
rtc: pic32: Delete owner assignment
rtc: bq32k: Fix handling of oscillator failure flag
rtc: bq32k: Use correct mask name for 'minutes' register.
rtc: sysfs: fix a cast removing the const attribute
Documentation: dt: Intersil isl12057 is not a trivial device
...
Linus Torvalds [Fri, 14 Oct 2016 20:09:41 +0000 (13:09 -0700)]
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"A small update pull request from I2C.
This adds one comment to a change we did in this merge window to
handle lockdep better, and pulls in a branch which should have been in
4.8 already improving DT support for I2C"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
gpio: pca953x: add a comment explaining the need for a lockdep subclass
i2c: core: Add support for 'i2c-bus' subnode
dt-bindings: i2c: Add support for 'i2c-bus' subnode
Linus Torvalds [Fri, 14 Oct 2016 19:50:05 +0000 (12:50 -0700)]
Merge tag 'acpi-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"This includes a couple of fixes needed after recent changes, two ACPI
driver fixes (fan and "Processor Aggregator"), an update of the ACPI
device properties handling code and a new MAINTAINERS entry for ACPI
on ARM64.
Specifics:
- Fix an unused function warning that started to appear after recent
changes in the ACPI EC driver (Eric Biggers).
- Fix the KERN_CONT usage in acpi_os_vprintf() that has become
(particularly) annoying recently (Joe Perches).
- Fix the fan status checking in the ACPI fan driver to avoid
returning incorrect error codes sometimes (Srinivas Pandruvada).
- Fix the ACPI Processor Aggregator driver (PAD) to always let the
special processor_aggregator driver from Xen take over when running
as Xen dom0 (Juergen Gross).
- Update the handling of reference device properties in ACPI by
allowing empty rows ("holes") to appear in reference property lists
(Mika Westerberg).
- Add a new MAINTAINERS entry for ACPI on ARM64 (Lorenzo Pieralisi)"
* tag 'acpi-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi_os_vprintf: Use printk_get_level() to avoid unnecessary KERN_CONT
ACPI / PAD: don't register acpi_pad driver if running as Xen dom0
ACPI / property: Allow holes in reference properties
MAINTAINERS: Add ARM64-specific ACPI maintainers entry
ACPI / EC: Fix unused function warning when CONFIG_PM_SLEEP=n
ACPI / fan: Fix error reading cur_state
Linus Torvalds [Fri, 14 Oct 2016 19:46:13 +0000 (12:46 -0700)]
Merge tag 'pm-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"This includes a couple of fixes for cpufreq regressions introduced in
4.8, a rework of the intel_pstate algorithm used on Atom processors
(that took some time to test) plus a fix and a couple of cleanups in
that driver, a CPPC cpufreq driver fix, and a some devfreq fixes and
cleanups (core and exynos-nocp).
Specifics:
- Fix two cpufreq regressions causing undesirable changes in behavior
to appear (one in the core and one in the conservative governor)
introduced during the 4.8 cycle (Aaro Koskinen, Rafael Wysocki).
- Fix the way the intel_pstate driver accesses MSRs related to the
hardware-managed P-states (HWP) feature during the initialization
which currently is unsafe and may cause the processor to generate a
general protection fault (Srinivas Pandruvada).
- Rework the intel_pstate's P-state selection algorithm used on Atom
processors to avoid known problems with the current one and to make
the computation more straightforward, which also happens to improve
performance in multiple benchmarks a bit (Rafael Wysocki).
- Improve two comments in the intel_pstate driver (Rafael Wysocki).
- Fix the desired performance computation in the CPPC cpufreq driver
(Hoan Tran).
- Fix the devfreq core to avoid printing misleading error messages in
some cases (Tobias Jakobi).
- Fix the error code path in devfreq_add_device() to use proper
locking around list modifications (Axel Lin).
- Fix a build failure and remove a couple of redundant updates of
variables in the exynos-nocp devfreq driver (Axel Lin)"
* tag 'pm-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: CPPC: Correct desired_perf calculation
cpufreq: conservative: Fix next frequency selection
cpufreq: skip invalid entries when searching the frequency
cpufreq: intel_pstate: Fix struct pstate_adjust_policy kerneldoc
cpufreq: intel_pstate: Proportional algorithm for Atom
PM / devfreq: Skip status update on uninitialized previous_freq
PM / devfreq: Add proper locking around list_del()
PM / devfreq: exynos-nocp: Remove redundant code
PM / devfreq: exynos-nocp: Select REGMAP_MMIO
cpufreq: intel_pstate: Clarify comment in get_target_pstate_use_performance()
cpufreq: intel_pstate: Fix unsafe HWP MSR access
Steve French [Fri, 14 Oct 2016 00:06:23 +0000 (19:06 -0500)]
CIFS: Retrieve uid and gid from special sid if enabled
New mount option "idsfromsid" indicates to cifs.ko that
it should try to retrieve the uid and gid owner fields
from special sids. This patch adds the code to parse the owner
sids in the ACL to see if they match, and if so populate the
uid and/or gid from them. This is faster than upcalling for
them and asking winbind, and is a fairly common case, and is
also helpful when cifs.upcall and idmapping is not configured.
Signed-off-by: Steve French <steve.french@primarydata.com> Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Steve French [Fri, 23 Sep 2016 06:36:34 +0000 (01:36 -0500)]
CIFS: Add new mount option to set owner uid and gid from special sids in acl
Add "idsfromsid" mount option to indicate to cifs.ko that it should
try to retrieve the uid and gid owner fields from special sids in the
ACL if present. This first patch just adds the parsing for the mount
option.
Signed-off-by: Steve French <steve.french@primarydata.com> Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Linus Torvalds [Fri, 14 Oct 2016 19:18:50 +0000 (12:18 -0700)]
Merge branch 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- tracepoints for basic cgroup management operations added
- kernfs and cgroup path formatting functions updated to behave in the
style of strlcpy()
- non-critical bug fixes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
blkcg: Unlock blkcg_pol_mutex only once when cpd == NULL
cgroup: fix error handling regressions in proc_cgroup_show() and cgroup_release_agent()
cpuset: fix error handling regression in proc_cpuset_show()
cgroup: add tracepoints for basic operations
cgroup: make cgroup_path() and friends behave in the style of strlcpy()
kernfs: remove kernfs_path_len()
kernfs: make kernfs_path*() behave in the style of strlcpy()
kernfs: add dummy implementation of kernfs_path_from_node()
Ram Amrani [Mon, 10 Oct 2016 10:15:30 +0000 (13:15 +0300)]
qedr: Add RoCE driver framework
Adds a skeletal implementation of the qed* RoCE driver -
basically the ability to communicate with the qede driver and
receive notifications from it regarding various init/exit events.
Linus Torvalds [Fri, 14 Oct 2016 18:46:25 +0000 (11:46 -0700)]
Merge branch 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu updates from Tejun Heo:
- Nick improved generic implementations of percpu operations which
modify the variable and return so that they calculate the physical
address only once.
- percpu_ref percpu <-> atomic mode switching improvements. The
patchset was originally posted about a year ago but fell through the
crack.
- misc non-critical fixes.
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
mm/percpu.c: fix potential memory leakage for pcpu_embed_first_chunk()
mm/percpu.c: correct max_distance calculation for pcpu_embed_first_chunk()
percpu: eliminate two sparse warnings
percpu: improve generic percpu modify-return implementation
percpu-refcount: init ->confirm_switch member properly
percpu_ref: allow operation mode switching operations to be called concurrently
percpu_ref: restructure operation mode switching
percpu_ref: unify staggered atomic switching wait behavior
percpu_ref: reorganize __percpu_ref_switch_to_atomic() and relocate percpu_ref_switch_to_atomic()
percpu_ref: remove unnecessary RCU grace period for staggered atomic switching confirmation
Linus Torvalds [Fri, 14 Oct 2016 18:41:28 +0000 (11:41 -0700)]
Merge branch 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
- Write same support added
- Minor ahci MSIX irq handling updates
- Non-critical SCSI command translation fixes
- Controller specific changes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: Revert "ahci: qoriq: Disable NCQ on ls2080a SoC"
libata: remove <asm-generic/libata-portmap.h>
libata: remove unused definitions from <asm/libata-portmap.h>
pata_at91: Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
ata: Replace BUG() with BUG_ON().
ata: sata_mv: Replacing dma_pool_alloc and memset with a single call dma_pool_zalloc.
libata: Some drives failing on SCT Write Same
ahci: use pci_alloc_irq_vectors
libata: SCT Write Same handle ATA_DFLAG_PIO
libata: SCT Write Same / DSM Trim
libata: Add support for SCT Write Same
libata: Safely overwrite attached page in WRITE SAME xlat
ahci: also use a per-port lock for the multi-MSIX case
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ahci: st: Add ports-implemented property in support
ahci: qoriq: enable snoopable sata read and write
ahci: qoriq: adjust sata parameter
libata-scsi: fix MODE SELECT translation for Control mode page
libata-scsi: use u8 array to store mode page copy
Linus Torvalds [Fri, 14 Oct 2016 18:37:50 +0000 (11:37 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a set of minor updates and fixes which weren't quite
ready in time for the first pull request.
The only real thing of note is Mike Christie is stepping down as
Maintainer of iscsi to be replaced by Lee Duncan and Chris Leech"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Kconfig fix
scsi: g_NCR5380: Stop using scsi_module.c
scsi: g_NCR5380: Reduce overrides[] from array to struct
scsi: g_NCR5380: Remove deprecated __setup
scsi: ufs: Fix error return code in ufshcd_init()
scsi: ufs: Data Segment only needed for WRITE DESCRIPTOR
scsi: cxgb4i: Set completion bit in work request
MAINTAINERS: Update open-iscsi maintainers
scsi: ufs: Enable no vccq quirk for skhynix device
scsi: be2iscsi: mark symbols static where possible
Linus Torvalds [Fri, 14 Oct 2016 18:11:39 +0000 (11:11 -0700)]
Merge tag 'metag-for-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture fix from James Hogan:
"A simple build fix for irqsoff atomics which has started hitting
meta1_defconfig during the 4.9 merge window"
* tag 'metag-for-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Only define atomic_dec_if_positive conditionally
Linus Torvalds [Fri, 14 Oct 2016 18:07:42 +0000 (11:07 -0700)]
Merge tag 'powerpc-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"Some more powerpc updates for 4.9:
Freescale updates from Scott Wood:
- qbman support (a prerequisite for datapath drivers such as ethernet)
- a PCI DMA fix+improvement
- reset handler changes
- more 8xx optimizations
- some cleanups and fixes.'
Miklos Szeredi [Tue, 4 Oct 2016 12:40:45 +0000 (14:40 +0200)]
vfs: add vfs_get_link() helper
This helper is for filesystems that want to read the symlink and are better
off with the get_link() interface (returning a char *) rather than the
readlink() interface (copy into a userspace buffer).
Also call the LSM hook for readlink (not get_link) since this is for
symlink reading not following.
1) Fix various build warnings in tlan/qed/xen-netback drivers, from
Arnd Bergmann.
2) Propagate proper error code in strparser's strp_recv(), from Geert
Uytterhoeven.
3) Fix accidental broadcast of RTM_GETTFILTER responses, from Eric
Dumazret.
4) Need to use list_for_each_entry_safe() in qed driver, from Wei
Yongjun.
5) Openvswitch 802.1AD bug fixes from Jiri Benc.
6) Cure BUILD_BUG_ON() in mlx5 driver, from Tom Herbert.
7) Fix UDP ipv6 checksumming in netvsc driver, from Stephen Hemminger.
8) stmmac driver fixes from Giuseppe CAVALLARO.
9) Fix access to mangled IP6CB in tcp, from Eric Dumazet.
10) Fix info leaks in tipc and rtnetlink, from Dan Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net: bridge: add the multicast_flood flag attribute to brport_attrs
net: axienet: Remove unused parameter from __axienet_device_reset
liquidio: CN23XX: fix a loop timeout
net: rtnl: info leak in rtnl_fill_vfinfo()
tipc: info leak in __tipc_nl_add_udp_addr()
net: ipv4: Do not drop to make_route if oif is l3mdev
net: phy: Trigger state machine on state change and not polling.
ipv6: tcp: restore IP6CB for pktoptions skbs
netvsc: Remove mistaken udp.h inclusion.
xen-netback: fix type mismatch warning
stmmac: fix error check when init ptp
stmmac: fix ptp init for gmac4
qed: fix old-style function definition
netvsc: fix checksum on UDP IPV6
net_sched: reorder pernet ops and act ops registrations
xen-netback: fix guest Rx stall detection (after guest Rx refactor)
drivers/ptp: Fix kernel memory disclosure
net/mlx5: Add MLX5_ARRAY_SET64 to fix BUILD_BUG_ON
qmi_wwan: add support for Quectel EC21 and EC25
openvswitch: add NETIF_F_HW_VLAN_STAG_TX to internal dev
...
Linus Torvalds [Fri, 14 Oct 2016 04:28:20 +0000 (21:28 -0700)]
Merge tag 'nfs-for-4.9-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"Highlights include:
Stable bugfixes:
- sunrpc: fix writ espace race causing stalls
- NFS: Fix inode corruption in nfs_prime_dcache()
- NFSv4: Don't report revoked delegations as valid in nfs_have_delegation()
- NFSv4: nfs4_copy_delegation_stateid() must fail if the delegation is invalid
- NFSv4: Open state recovery must account for file permission changes
- NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
Features:
- Add support for tracking multiple layout types with an ordered list
- Add support for using multiple backchannel threads on the client
- Add support for pNFS file layout session trunking
- Delay xprtrdma use of DMA API (for device driver removal)
- Add support for xprtrdma remote invalidation
- Add support for larger xprtrdma inline thresholds
- Use a scatter/gather list for sending xprtrdma RPC calls
- Add support for the CB_NOTIFY_LOCK callback
- Improve hashing sunrpc auth_creds by using both uid and gid
Bugfixes:
- Fix xprtrdma use of DMA API
- Validate filenames before adding to the dcache
- Fix corruption of xdr->nwords in xdr_copy_to_scratch
- Fix setting buffer length in xdr_set_next_buffer()
- Don't deadlock the state manager on the SEQUENCE status flags
- Various delegation and stateid related fixes
- Retry operations if an interrupted slot receives EREMOTEIO
- Make nfs boot time y2038 safe"
* tag 'nfs-for-4.9-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (100 commits)
NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
fs: nfs: Make nfs boot time y2038 safe
sunrpc: replace generic auth_cred hash with auth-specific function
sunrpc: add RPCSEC_GSS hash_cred() function
sunrpc: add auth_unix hash_cred() function
sunrpc: add generic_auth hash_cred() function
sunrpc: add hash_cred() function to rpc_authops struct
Retry operation on EREMOTEIO on an interrupted slot
pNFS: Fix atime updates on pNFS clients
sunrpc: queue work on system_power_efficient_wq
NFSv4.1: Even if the stateid is OK, we may need to recover the open modes
NFSv4: If recovery failed for a specific open stateid, then don't retry
NFSv4: Fix retry issues with nfs41_test/free_stateid
NFSv4: Open state recovery must account for file permission changes
NFSv4: Mark the lock and open stateids as invalid after freeing them
NFSv4: Don't test open_stateid unless it is set
NFSv4: nfs4_do_handle_exception() handle revoke/expiry of a single stateid
NFS: Always call nfs_inode_find_state_and_recover() when revoking a delegation
NFSv4: Fix a race when updating an open_stateid
NFSv4: Fix a race in nfs_inode_reclaim_delegation()
...
Linus Torvalds [Fri, 14 Oct 2016 04:04:42 +0000 (21:04 -0700)]
Merge tag 'nfsd-4.9' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Some RDMA work and some good bugfixes, and two new features that could
benefit from user testing:
- Anna Schumacker contributed a simple NFSv4.2 COPY implementation.
COPY is already supported on the client side, so a call to
copy_file_range() on a recent client should now result in a
server-side copy that doesn't require all the data to make a round
trip to the client and back.
- Jeff Layton implemented callbacks to notify clients when contended
locks become available, which should reduce latency on workloads
with contended locks"
* tag 'nfsd-4.9' of git://linux-nfs.org/~bfields/linux:
NFSD: Implement the COPY call
nfsd: handle EUCLEAN
nfsd: only WARN once on unmapped errors
exportfs: be careful to only return expected errors.
nfsd4: setclientid_confirm with unmatched verifier should fail
nfsd: randomize SETCLIENTID reply to help distinguish servers
nfsd: set the MAY_NOTIFY_LOCK flag in OPEN replies
nfs: add a new NFS4_OPEN_RESULT_MAY_NOTIFY_LOCK constant
nfsd: add a LRU list for blocked locks
nfsd: have nfsd4_lock use blocking locks for v4.1+ locks
nfsd: plumb in a CB_NOTIFY_LOCK operation
NFSD: fix corruption in notifier registration
svcrdma: support Remote Invalidation
svcrdma: Server-side support for rpcrdma_connect_private
rpcrdma: RDMA/CM private message data structure
svcrdma: Skip put_page() when send_reply() fails
svcrdma: Tail iovec leaves an orphaned DMA mapping
nfsd: fix dprintk in nfsd4_encode_getdeviceinfo
nfsd: eliminate cb_minorversion field
nfsd: don't set a FL_LAYOUT lease for flexfiles layouts
Linus Torvalds [Fri, 14 Oct 2016 03:28:22 +0000 (20:28 -0700)]
Merge tag 'xfs-reflink-for-linus-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
< XFS has gained super CoW powers! >
----------------------------------
\ ^__^
\ (oo)\_______
(__)\ )\/\
||----w |
|| ||
Pull XFS support for shared data extents from Dave Chinner:
"This is the second part of the XFS updates for this merge cycle. This
pullreq contains the new shared data extents feature for XFS.
Given the complexity and size of this change I am expecting - like the
addition of reverse mapping last cycle - that there will be some
follow-up bug fixes and cleanups around the -rc3 stage for issues that
I'm sure will show up once the code hits a wider userbase.
What it is:
At the most basic level we are simply adding shared data extents to
XFS - i.e. a single extent on disk can now have multiple owners. To do
this we have to add new on-disk features to both track the shared
extents and the number of times they've been shared. This is done by
the new "refcount" btree that sits in every allocation group. When we
share or unshare an extent, this tree gets updated.
Along with this new tree, the reverse mapping tree needs to be updated
to track each owner or a shared extent. This also needs to be updated
ever share/unshare operation. These interactions at extent allocation
and freeing time have complex ordering and recovery constraints, so
there's a significant amount of new intent-based transaction code to
ensure that operations are performed atomically from both the runtime
and integrity/crash recovery perspectives.
We also need to break sharing when writes hit a shared extent - this
is where the new copy-on-write implementation comes in. We allocate
new storage and copy the original data along with the overwrite data
into the new location. We only do this for data as we don't share
metadata at all - each inode has it's own metadata that tracks the
shared data extents, the extents undergoing CoW and it's own private
extents.
Of course, being XFS, nothing is simple - we use delayed allocation
for CoW similar to how we use it for normal writes. ENOSPC is a
significant issue here - we build on the reservation code added in
4.8-rc1 with the reverse mapping feature to ensure we don't get
spurious ENOSPC issues part way through a CoW operation. These
mechanisms also help minimise fragmentation due to repeated CoW
operations. To further reduce fragmentation overhead, we've also
introduced a CoW extent size hint, which indicates how large a region
we should allocate when we execute a CoW operation.
With all this functionality in place, we can hook up .copy_file_range,
.clone_file_range and .dedupe_file_range and we gain all the
capabilities of reflink and other vfs provided functionality that
enable manipulation to shared extents. We also added a fallocate mode
that explicitly unshares a range of a file, which we implemented as an
explicit CoW of all the shared extents in a file.
As such, it's a huge chunk of new functionality with new on-disk
format features and internal infrastructure. It warns at mount time as
an experimental feature and that it may eat data (as we do with all
new on-disk features until they stabilise). We have not released
userspace suport for it yet - userspace support currently requires
download from Darrick's xfsprogs repo and build from source, so the
access to this feature is really developer/tester only at this point.
Initial userspace support will be released at the same time the kernel
with this code in it is released.
The new code causes 5-6 new failures with xfstests - these aren't
serious functional failures but things the output of tests changing
slightly due to perturbations in layouts, space usage, etc. OTOH,
we've added 150+ new tests to xfstests that specifically exercise this
new functionality so it's got far better test coverage than any
functionality we've previously added to XFS.
Darrick has done a pretty amazing job getting us to this stage, and
special mention also needs to go to Christoph (review, testing,
improvements and bug fixes) and Brian (caught several intricate bugs
during review) for the effort they've also put in.
Summary:
- unshare range (FALLOC_FL_UNSHARE) support for fallocate
- copy-on-write extent size hints (FS_XFLAG_COWEXTSIZE) for fsxattr
interface
- shared extent support for XFS
- copy-on-write support for shared extents
- copy_file_range support
- clone_file_range support (implements reflink)
- dedupe_file_range support
- defrag support for reverse mapping enabled filesystems"
* tag 'xfs-reflink-for-linus-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (71 commits)
xfs: convert COW blocks to real blocks before unwritten extent conversion
xfs: rework refcount cow recovery error handling
xfs: clear reflink flag if setting realtime flag
xfs: fix error initialization
xfs: fix label inaccuracies
xfs: remove isize check from unshare operation
xfs: reduce stack usage of _reflink_clear_inode_flag
xfs: check inode reflink flag before calling reflink functions
xfs: implement swapext for rmap filesystems
xfs: refactor swapext code
xfs: various swapext cleanups
xfs: recognize the reflink feature bit
xfs: simulate per-AG reservations being critically low
xfs: don't mix reflink and DAX mode for now
xfs: check for invalid inode reflink flags
xfs: set a default CoW extent size of 32 blocks
xfs: convert unwritten status of reverse mappings for shared files
xfs: use interval query for rmap alloc operations on shared files
xfs: add shared rmap map/unmap/convert log item types
xfs: increase log reservations for reflink
...
Pavel Shilovsky [Tue, 11 Oct 2016 22:34:07 +0000 (15:34 -0700)]
CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
We are already doing the same thing for an ordinary open case:
we can't keep read oplock on a file if we have mandatory byte-range
locks because pagereading can conflict with these locks on a server.
Fix it by setting oplock level to NONE.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com>
Pavel Shilovsky [Sat, 8 Oct 2016 00:26:36 +0000 (17:26 -0700)]
CIFS: Fix persistent handles re-opening on reconnect
openFileList of tcon can be changed while cifs_reopen_file() is called
that can lead to an unexpected behavior when we return to the loop.
Fix this by introducing a temp list for keeping all file handles that
need to be reopen.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com>
Sachin Prabhu [Fri, 7 Oct 2016 18:11:22 +0000 (19:11 +0100)]
SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
We split the rawntlmssp authentication into negotiate and
authencate parts. We also clean up the code and add helpers.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Sachin Prabhu [Fri, 7 Oct 2016 18:11:21 +0000 (19:11 +0100)]
SMB2: Separate Kerberos authentication from SMB2_sess_setup
Add helper functions and split Kerberos authentication off
SMB2_sess_setup.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Steve French [Mon, 26 Sep 2016 19:23:08 +0000 (14:23 -0500)]
Do not send SMB3 SET_INFO request if nothing is changing
[CIFS] We had cases where we sent a SMB2/SMB3 setinfo request with all
timestamp (and DOS attribute) fields marked as 0 (ie do not change)
e.g. on chmod or chown.
Signed-off-by: Steve French <steve.french@primarydata.com> CC: Stable <stable@vger.kernel.org>
Linus Torvalds [Fri, 14 Oct 2016 00:08:58 +0000 (17:08 -0700)]
Merge tag 'pci-v4.9-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
PCI changes for the v4.9 merge window:
"Here are some more changes I'd like to have in v4.9. There's one
small Tegra bug fix in the PHY poweroff path, which is only used in
failure paths.
The rest is all strictly cleanup that should make host bridge drivers
more readable, but shouldn't actually change any behavior.
Summary:
- use local struct device pointers in many host bridge drivers for
clarity
- remove unused platform data
- use generic DesignWare accessors
- misc cleanups: remove redundant structure entries and re-order
structure members to put comon generic fields first etc"
* tag 'pci-v4.9-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
MAINTAINERS: Add maintainer for the PCIe Marvell Armada 8K driver
MAINTAINERS: Add DT binding to the Aardvark PCIe driver maintainer
PCI: rockchip: Indent "if" statement body
PCI: hisi: Reorder struct hisi_pcie
PCI: hisi: Pass device-specific struct to internal functions
PCI: hisi: Include register block base in PCIE_SYS_STATE4 address
PCI: dra7xx: Reorder struct dra7xx_pcie
PCI: xilinx-nwl: Remove unused platform data
PCI: xilinx-nwl: Add local struct device pointers
PCI: xilinx: Removed unused xilinx_pcie_assign_msi() argument
PCI: xilinx: Remove unused platform data
PCI: xilinx: Add local struct device pointers
PCI: xgene: Add register accessors
PCI: xgene: Pass struct xgene_pcie_port to setup functions
PCI: xgene: Remove unused platform data
PCI: tegra: Remove unused platform data
PCI: tegra: Add local struct device pointers
PCI: tegra: Fix argument order in tegra_pcie_phy_disable()
PCI: rockchip: Remove unused platform data
PCI: rcar-gen2: Add local struct device pointers
...
Linus Torvalds [Thu, 13 Oct 2016 23:52:39 +0000 (16:52 -0700)]
Merge tag 'platform-drivers-x86-v4.9-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers updates from Darren Hart:
"Cleanups, refactoring, and a couple bug fixes.
intel_pmc_core:
- avoid boot time warning for !CONFIG_DEBUGFS_FS
intel_pmc_ipc:
- Convert to use platform_device_register_full
asus-wmi:
- Filter buggy scan codes on ASUS Q500A
toshiba_bluetooth:
- Decouple an error checking status code
toshiba_haps:
- Change logging level from info to debug
- Split ACPI and HDD protection error handling
asus-laptop:
- get rid of parse_arg()
asus-wmi:
- fix asus ux303ub brightness issue
toshiba_acpi:
- Fix typo in *_cooling_method_set function
- Change error checking logic from TCI functions
- Clean up variable declaration"
* tag 'platform-drivers-x86-v4.9-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: intel_pmc_core: avoid boot time warning for !CONFIG_DEBUGFS_FS
platform/x86: intel_pmc_ipc: Convert to use platform_device_register_full
platform/x86: asus-wmi: Filter buggy scan codes on ASUS Q500A
platform/x86: toshiba_bluetooth: Decouple an error checking status code
platform/x86: toshiba_haps: Change logging level from info to debug
platform/x86: toshiba_haps: Split ACPI and HDD protection error handling
platform/x86: asus-laptop: get rid of parse_arg()
platform/x86: asus-wmi: fix asus ux303ub brightness issue
platform/x86: toshiba_acpi: Fix typo in *_cooling_method_set function
platform/x86: toshiba_acpi: Change error checking logic from TCI functions
platform/x86: toshiba_acpi: Clean up variable declaration
projects / karo-tx-linux.git / log