arch/arm/boot/dts/armada-388-gp.dts

   1 /*
   2  * Device Tree file for Marvell Armada 385 development board
   3  * (RD-88F6820-GP)
   4  *
   5  * Copyright (C) 2014 Marvell
   6  *
   7  * Gregory CLEMENT <gregory.clement@free-electrons.com>
   8  *
   9  * This file is dual-licensed: you can use it either under the terms
  10  * of the GPL or the X11 license, at your option. Note that this dual
  11  * licensing only applies to this file, and not this project as a
  12  * whole.
  13  *
  14  *  a) This file is licensed under the terms of the GNU General Public
  15  *     License version 2.  This program is licensed "as is" without
  16  *     any warranty of any kind, whether express or implied.
  17  *
  18  * Or, alternatively,
  19  *
  20  *  b) Permission is hereby granted, free of charge, to any person
  21  *     obtaining a copy of this software and associated documentation
  22  *     files (the "Software"), to deal in the Software without
  23  *     restriction, including without limitation the rights to use,
  24  *     copy, modify, merge, publish, distribute, sublicense, and/or
  25  *     sell copies of the Software, and to permit persons to whom the
  26  *     Software is furnished to do so, subject to the following
  27  *     conditions:
  28  *
  29  *     The above copyright notice and this permission notice shall be
  30  *     included in all copies or substantial portions of the Software.
  31  *
  32  *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
  33  *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
  34  *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
  35  *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
  36  *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
  37  *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
  38  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  39  *     OTHER DEALINGS IN THE SOFTWARE.
  40  */
  41
  42 /dts-v1/;
  43 #include "armada-388.dtsi"
  44 #include <dt-bindings/gpio/gpio.h>
  45
  46 / {
  47         model = "Marvell Armada 388 DB-88F6820-GP";
  48         compatible = "marvell,a388-gp", "marvell,armada388", "marvell,armada380";
  49
  50         chosen {
  51                 stdout-path = "serial0:115200n8";
  52         };
  53
  54         memory {
  55                 device_type = "memory";
  56                 reg = <0x00000000 0x80000000>; /* 2 GB */
  57         };
  58
  59         soc {
  60                 ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
  61                           MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
  62                           MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
  63                           MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
  64                           MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
  65
  66                 internal-regs {
  67                         i2c@11000 {
  68                                 pinctrl-names = "default";
  69                                 pinctrl-0 = <&i2c0_pins>;
  70                                 status = "okay";
  71                                 clock-frequency = <100000>;
  72
  73                                 expander0: pca9555@20 {
  74                                         compatible = "nxp,pca9555";
  75                                         pinctrl-names = "default";
  76                                         pinctrl-0 = <&pca0_pins>;
  77                                         interrupt-parent = <&gpio0>;
  78                                         interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
  79                                         gpio-controller;
  80                                         #gpio-cells = <2>;
  81                                         interrupt-controller;
  82                                         #interrupt-cells = <2>;
  83                                         reg = <0x20>;
  84                                 };
  85
  86                                 expander1: pca9555@21 {
  87                                         compatible = "nxp,pca9555";
  88                                         pinctrl-names = "default";
  89                                         interrupt-parent = <&gpio0>;
  90                                         interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
  91                                         gpio-controller;
  92                                         #gpio-cells = <2>;
  93                                         interrupt-controller;
  94                                         #interrupt-cells = <2>;
  95                                         reg = <0x21>;
  96                                 };
  97
  98                                 eeprom@57 {
  99                                         compatible = "atmel,24c64";
 100                                         reg = <0x57>;
 101                                 };
 102                         };
 103
 104                         serial@12000 {
 105                                 /*
 106                                  * Exported on the micro USB connector CON16
 107                                  * through an FTDI
 108                                  */
 109
 110                                 pinctrl-names = "default";
 111                                 pinctrl-0 = <&uart0_pins>;
 112                                 status = "okay";
 113                         };
 114
 115                         /* GE1 CON15 */
 116                         ethernet@30000 {
 117                                 pinctrl-names = "default";
 118                                 pinctrl-0 = <&ge1_rgmii_pins>;
 119                                 status = "okay";
 120                                 phy = <&phy1>;
 121                                 phy-mode = "rgmii-id";
 122                                 buffer-manager = <&bm>;
 123                                 bm,pool-long = <2>;
 124                                 bm,pool-short = <3>;
 125                         };
 126
 127                         /* CON4 */
 128                         usb@58000 {
 129                                 vcc-supply = <&reg_usb2_0_vbus>;
 130                                 status = "okay";
 131                         };
 132
 133                         /* GE0 CON1 */
 134                         ethernet@70000 {
 135                                 pinctrl-names = "default";
 136                                 /*
 137                                  * The Reference Clock 0 is used to provide a
 138                                  * clock to the PHY
 139                                  */
 140                                 pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
 141                                 status = "okay";
 142                                 phy = <&phy0>;
 143                                 phy-mode = "rgmii-id";
 144                                 buffer-manager = <&bm>;
 145                                 bm,pool-long = <0>;
 146                                 bm,pool-short = <1>;
 147                         };
 148
 149
 150                         mdio@72004 {
 151                                 pinctrl-names = "default";
 152                                 pinctrl-0 = <&mdio_pins>;
 153
 154                                 phy0: ethernet-phy@1 {
 155                                         reg = <1>;
 156                                 };
 157
 158                                 phy1: ethernet-phy@0 {
 159                                         reg = <0>;
 160                                 };
 161                         };
 162
 163                         sata@a8000 {
 164                                 pinctrl-names = "default";
 165                                 pinctrl-0 = <&sata0_pins>, <&sata1_pins>;
 166                                 status = "okay";
 167                                 #address-cells = <1>;
 168                                 #size-cells = <0>;
 169
 170                                 sata0: sata-port@0 {
 171                                         reg = <0>;
 172                                         target-supply = <&reg_5v_sata0>;
 173                                 };
 174
 175                                 sata1: sata-port@1 {
 176                                         reg = <1>;
 177                                         target-supply = <&reg_5v_sata1>;
 178                                 };
 179                         };
 180
 181                         bm@c8000 {
 182                                 status = "okay";
 183                         };
 184
 185                         sata@e0000 {
 186                                 pinctrl-names = "default";
 187                                 pinctrl-0 = <&sata2_pins>, <&sata3_pins>;
 188                                 status = "okay";
 189                                 #address-cells = <1>;
 190                                 #size-cells = <0>;
 191
 192                                 sata2: sata-port@0 {
 193                                         reg = <0>;
 194                                         target-supply = <&reg_5v_sata2>;
 195                                 };
 196
 197                                 sata3: sata-port@1 {
 198                                         reg = <1>;
 199                                         target-supply = <&reg_5v_sata3>;
 200                                 };
 201                         };
 202
 203                         sdhci@d8000 {
 204                                 pinctrl-names = "default";
 205                                 pinctrl-0 = <&sdhci_pins>;
 206                                 no-1-8-v;
 207                                 /*
 208                                  * A388-GP board v1.5 and higher replace
 209                                  * hitherto card detection method based on GPIO
 210                                  * with the one using DAT3 pin. As they are
 211                                  * incompatible, software-based polling is
 212                                  * enabled with 'broken-cd' property. For boards
 213                                  * older than v1.5 it can be replaced with:
 214                                  * 'cd-gpios = <&expander0 5 GPIO_ACTIVE_LOW>;',
 215                                  * whereas for the newer ones following can be
 216                                  * used instead:
 217                                  * 'dat3-cd;'
 218                                  * 'cd-inverted;'
 219                                  */
 220                                 broken-cd;
 221                                 wp-inverted;
 222                                 bus-width = <8>;
 223                                 status = "okay";
 224                         };
 225
 226                         /* CON5 */
 227                         usb3@f0000 {
 228                                 usb-phy = <&usb2_1_phy>;
 229                                 status = "okay";
 230                         };
 231
 232                         /* CON7 */
 233                         usb3@f8000 {
 234                                 usb-phy = <&usb3_phy>;
 235                                 status = "okay";
 236                         };
 237                 };
 238
 239                 bm-bppi {
 240                         status = "okay";
 241                 };
 242
 243                 pcie-controller {
 244                         status = "okay";
 245                         /*
 246                          * One PCIe units is accessible through
 247                          * standard PCIe slot on the board.
 248                          */
 249                         pcie@1,0 {
 250                                 /* Port 0, Lane 0 */
 251                                 status = "okay";
 252                         };
 253
 254                         /*
 255                          * The two other PCIe units are accessible
 256                          * through mini PCIe slot on the board.
 257                          */
 258                         pcie@2,0 {
 259                                 /* Port 1, Lane 0 */
 260                                 status = "okay";
 261                         };
 262                         pcie@3,0 {
 263                                 /* Port 2, Lane 0 */
 264                                 status = "okay";
 265                         };
 266                 };
 267
 268                 gpio-fan {
 269                         compatible = "gpio-fan";
 270                         gpios = <&expander1 3 GPIO_ACTIVE_HIGH>;
 271                         gpio-fan,speed-map = <   0 0
 272                                               3000 1>;
 273                 };
 274         };
 275
 276         usb2_1_phy: usb2_1_phy {
 277                 compatible = "usb-nop-xceiv";
 278                 vcc-supply = <&reg_usb2_1_vbus>;
 279         };
 280
 281         usb3_phy: usb3_phy {
 282                 compatible = "usb-nop-xceiv";
 283                 vcc-supply = <&reg_usb3_vbus>;
 284         };
 285
 286         reg_usb3_vbus: usb3-vbus {
 287                 compatible = "regulator-fixed";
 288                 regulator-name = "usb3-vbus";
 289                 regulator-min-microvolt = <5000000>;
 290                 regulator-max-microvolt = <5000000>;
 291                 enable-active-high;
 292                 gpio = <&expander1 15 GPIO_ACTIVE_HIGH>;
 293         };
 294
 295         reg_usb2_0_vbus: v5-vbus0 {
 296                 compatible = "regulator-fixed";
 297                 regulator-name = "v5.0-vbus0";
 298                 regulator-min-microvolt = <5000000>;
 299                 regulator-max-microvolt = <5000000>;
 300                 enable-active-high;
 301                 regulator-always-on;
 302                 gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
 303         };
 304
 305         reg_usb2_1_vbus: v5-vbus1 {
 306                 compatible = "regulator-fixed";
 307                 regulator-name = "v5.0-vbus1";
 308                 regulator-min-microvolt = <5000000>;
 309                 regulator-max-microvolt = <5000000>;
 310                 enable-active-high;
 311                 gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
 312         };
 313
 314         reg_sata0: pwr-sata0 {
 315                 compatible = "regulator-fixed";
 316                 regulator-name = "pwr_en_sata0";
 317                 regulator-min-microvolt = <12000000>;
 318                 regulator-max-microvolt = <12000000>;
 319                 enable-active-high;
 320                 regulator-boot-on;
 321                 gpio = <&expander0 2 GPIO_ACTIVE_HIGH>;
 322         };
 323
 324         reg_5v_sata0: v5-sata0 {
 325                 compatible = "regulator-fixed";
 326                 regulator-name = "v5.0-sata0";
 327                 regulator-min-microvolt = <5000000>;
 328                 regulator-max-microvolt = <5000000>;
 329                 vin-supply = <&reg_sata0>;
 330         };
 331
 332         reg_12v_sata0: v12-sata0 {
 333                 compatible = "regulator-fixed";
 334                 regulator-name = "v12.0-sata0";
 335                 regulator-min-microvolt = <12000000>;
 336                 regulator-max-microvolt = <12000000>;
 337                 vin-supply = <&reg_sata0>;
 338         };
 339
 340         reg_sata1: pwr-sata1 {
 341                 regulator-name = "pwr_en_sata1";
 342                 compatible = "regulator-fixed";
 343                 regulator-min-microvolt = <12000000>;
 344                 regulator-max-microvolt = <12000000>;
 345                 enable-active-high;
 346                 regulator-boot-on;
 347                 gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
 348         };
 349
 350         reg_5v_sata1: v5-sata1 {
 351                 compatible = "regulator-fixed";
 352                 regulator-name = "v5.0-sata1";
 353                 regulator-min-microvolt = <5000000>;
 354                 regulator-max-microvolt = <5000000>;
 355                 vin-supply = <&reg_sata1>;
 356         };
 357
 358         reg_12v_sata1: v12-sata1 {
 359                 compatible = "regulator-fixed";
 360                 regulator-name = "v12.0-sata1";
 361                 regulator-min-microvolt = <12000000>;
 362                 regulator-max-microvolt = <12000000>;
 363                 vin-supply = <&reg_sata1>;
 364         };
 365
 366         reg_sata2: pwr-sata2 {
 367                 compatible = "regulator-fixed";
 368                 regulator-name = "pwr_en_sata2";
 369                 enable-active-high;
 370                 regulator-boot-on;
 371                 gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
 372         };
 373
 374         reg_5v_sata2: v5-sata2 {
 375                 compatible = "regulator-fixed";
 376                 regulator-name = "v5.0-sata2";
 377                 regulator-min-microvolt = <5000000>;
 378                 regulator-max-microvolt = <5000000>;
 379                 vin-supply = <&reg_sata2>;
 380         };
 381
 382         reg_12v_sata2: v12-sata2 {
 383                 compatible = "regulator-fixed";
 384                 regulator-name = "v12.0-sata2";
 385                 regulator-min-microvolt = <12000000>;
 386                 regulator-max-microvolt = <12000000>;
 387                 vin-supply = <&reg_sata2>;
 388         };
 389
 390         reg_sata3: pwr-sata3 {
 391                 compatible = "regulator-fixed";
 392                 regulator-name = "pwr_en_sata3";
 393                 enable-active-high;
 394                 regulator-boot-on;
 395                 gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
 396         };
 397
 398         reg_5v_sata3: v5-sata3 {
 399                 compatible = "regulator-fixed";
 400                 regulator-name = "v5.0-sata3";
 401                 regulator-min-microvolt = <5000000>;
 402                 regulator-max-microvolt = <5000000>;
 403                 vin-supply = <&reg_sata3>;
 404         };
 405
 406         reg_12v_sata3: v12-sata3 {
 407                 compatible = "regulator-fixed";
 408                 regulator-name = "v12.0-sata3";
 409                 regulator-min-microvolt = <12000000>;
 410                 regulator-max-microvolt = <12000000>;
 411                 vin-supply = <&reg_sata3>;
 412         };
 413 };
 414
 415 &pinctrl {
 416         pca0_pins: pca0_pins {
 417                 marvell,pins = "mpp18";
 418                 marvell,function = "gpio";
 419         };
 420 };
 421
 422 &spi0 {
 423         pinctrl-names = "default";
 424         pinctrl-0 = <&spi0_pins>;
 425         status = "okay";
 426
 427         spi-flash@0 {
 428                 #address-cells = <1>;
 429                 #size-cells = <1>;
 430                 compatible = "st,m25p128", "jedec,spi-nor";
 431                 reg = <0>; /* Chip select 0 */
 432                 spi-max-frequency = <50000000>;
 433                 m25p,fast-read;
 434         };
 435 };