return max_bitflips;
}
-#define ECC_SECTOR_SIZE 512
-
#define ECC_SECTOR(x) (((x) & ECC_ERROR_ADDRESS__SECTOR_NR) >> 12)
#define ECC_BYTE(x) (((x) & ECC_ERROR_ADDRESS__OFFSET))
#define ECC_CORRECTION_VALUE(x) ((x) & ERR_CORRECTION_INFO__BYTEMASK)
struct denali_nand_info *denali,
unsigned long *uncor_ecc_flags, uint8_t *buf)
{
+ unsigned int ecc_size = denali->nand.ecc.size;
unsigned int bitflips = 0;
unsigned int max_bitflips = 0;
uint32_t err_addr, err_cor_info;
* an erased sector.
*/
*uncor_ecc_flags |= BIT(err_sector);
- } else if (err_byte < ECC_SECTOR_SIZE) {
+ } else if (err_byte < ecc_size) {
/*
- * If err_byte is larger than ECC_SECTOR_SIZE, means error
+ * If err_byte is larger than ecc_size, means error
* happened in OOB, so we ignore it. It's no need for
* us to correct it err_device is represented the NAND
* error bits are happened in if there are more than
int offset;
unsigned int flips_in_byte;
- offset = (err_sector * ECC_SECTOR_SIZE + err_byte) *
+ offset = (err_sector * ecc_size + err_byte) *
denali->devnum + err_device;
/* correct the ECC error */
denali_irq_init(denali);
}
-/*
- * Althogh controller spec said SLC ECC is forceb to be 4bit,
- * but denali controller in MRST only support 15bit and 8bit ECC
- * correction
- */
-#define ECC_8BITS 14
-#define ECC_15BITS 26
+int denali_calc_ecc_bytes(int step_size, int strength)
+{
+ /* BCH code. Denali requires ecc.bytes to be multiple of 2 */
+ return DIV_ROUND_UP(strength * fls(step_size * 8), 16) * 2;
+}
+EXPORT_SYMBOL(denali_calc_ecc_bytes);
+
+static int denali_ecc_setup(struct mtd_info *mtd, struct nand_chip *chip,
+ struct denali_nand_info *denali)
+{
+ int oobavail = mtd->oobsize - denali->bbtskipbytes;
+ int ret;
+
+ /*
+ * If .size and .strength are already set (usually by DT),
+ * check if they are supported by this controller.
+ */
+ if (chip->ecc.size && chip->ecc.strength)
+ return nand_check_ecc_caps(chip, denali->ecc_caps, oobavail);
+
+ /*
+ * We want .size and .strength closest to the chip's requirement
+ * unless NAND_ECC_MAXIMIZE is requested.
+ */
+ if (!(chip->ecc.options & NAND_ECC_MAXIMIZE)) {
+ ret = nand_match_ecc_req(chip, denali->ecc_caps, oobavail);
+ if (!ret)
+ return 0;
+ }
+
+ /* Max ECC strength is the last thing we can do */
+ return nand_maximize_ecc(chip, denali->ecc_caps, oobavail);
+}
static int denali_ooblayout_ecc(struct mtd_info *mtd, int section,
struct mtd_oob_region *oobregion)
/* no subpage writes on denali */
chip->options |= NAND_NO_SUBPAGE_WRITE;
- /*
- * Denali Controller only support 15bit and 8bit ECC in MRST,
- * so just let controller do 15bit ECC for MLC and 8bit ECC for
- * SLC if possible.
- * */
- if (!nand_is_slc(chip) &&
- (mtd->oobsize > (denali->bbtskipbytes +
- ECC_15BITS * (mtd->writesize /
- ECC_SECTOR_SIZE)))) {
- /* if MLC OOB size is large enough, use 15bit ECC*/
- chip->ecc.strength = 15;
- chip->ecc.bytes = ECC_15BITS;
- iowrite32(15, denali->flash_reg + ECC_CORRECTION);
- } else if (mtd->oobsize < (denali->bbtskipbytes +
- ECC_8BITS * (mtd->writesize /
- ECC_SECTOR_SIZE))) {
- pr_err("Your NAND chip OOB is not large enough to contain 8bit ECC correction codes");
+ ret = denali_ecc_setup(mtd, chip, denali);
+ if (ret) {
+ dev_err(denali->dev, "Failed to setup ECC settings.\n");
goto failed_req_irq;
- } else {
- chip->ecc.strength = 8;
- chip->ecc.bytes = ECC_8BITS;
- iowrite32(8, denali->flash_reg + ECC_CORRECTION);
}
+ dev_dbg(denali->dev,
+ "chosen ECC settings: step=%d, strength=%d, bytes=%d\n",
+ chip->ecc.size, chip->ecc.strength, chip->ecc.bytes);
+
+ iowrite32(chip->ecc.strength, denali->flash_reg + ECC_CORRECTION);
+
+ iowrite32(chip->ecc.size, denali->flash_reg + CFG_DATA_BLOCK_SIZE);
+ iowrite32(chip->ecc.size, denali->flash_reg + CFG_LAST_DATA_BLOCK_SIZE);
+ /* chip->ecc.steps is set by nand_scan_tail(); not available here */
+ iowrite32(mtd->writesize / chip->ecc.size,
+ denali->flash_reg + CFG_NUM_DATA_BLOCKS);
+
mtd_set_ooblayout(mtd, &denali_ooblayout_ops);
- /* override the default read operations */
- chip->ecc.size = ECC_SECTOR_SIZE;
chip->ecc.read_page = denali_read_page;
chip->ecc.read_page_raw = denali_read_page_raw;
chip->ecc.write_page = denali_write_page;
projects / karo-tx-linux.git / commitdiff