Michał Mirosław [Tue, 15 Nov 2011 15:29:55 +0000 (15:29 +0000)]
net: ethtool: break association of ETH_FLAG_* with NETIF_F_*
This is the only place left where dev->features are directly
exposed to userspace.
I know checkpatch.pl complains about __ethtool_{get,set}_flags(), but
the code is easier to read this way.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michał Mirosław [Tue, 15 Nov 2011 15:29:55 +0000 (15:29 +0000)]
net: remove legacy ethtool ops
As all drivers are converted, we may now remove discrete offload setting
callback handling.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 15 Nov 2011 04:12:55 +0000 (04:12 +0000)]
net: use jump_label for netstamp_needed
netstamp_needed seems a good candidate to jump_label conversion.
This avoids 3 conditional branches per incoming packet in fast path.
No measurable difference, given that these conditional branches are
predicted on modern cpus. Only a small icache reduction, thanks to the
unlikely() stuff.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Mon, 14 Nov 2011 14:17:08 +0000 (14:17 +0000)]
enable virtio_net to return bus_info in ethtool -i consistent with emulated NICs
Add a new .bus_name to virtio_config_ops then modify virtio_net to
call through to it in an ethtool .get_drvinfo routine to report
bus_info in ethtool -i output which is consistent with other
emulated NICs and the output of lspci.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-gpio: Add reset functionality to mdio-gpio driver(v2).
This patch adds phy reset functionality to mdio-gpio driver. Now
mdio_gpio_platform_data has new member as function pointer which can be
filled at the bsp level for a callback from phy infrastructure. Also the
mdio-bitbang driver fills-in the reset function of mii_bus structure.
Without this patch the bsp level code has to takecare of the reseting
PHY's on the bus, which become bit hacky for every bsp and
phy-infrastructure is ignored aswell.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matti Vaittinen [Mon, 14 Nov 2011 00:15:14 +0000 (00:15 +0000)]
IPv6 routing, NLM_F_* flag support: REPLACE and EXCL flags support, warn about missing CREATE flag
The support for NLM_F_* flags at IPv6 routing requests.
If NLM_F_CREATE flag is not defined for RTM_NEWROUTE request,
warning is printed, but no error is returned. Instead new route is
added. Later NLM_F_CREATE may be required for
new route creation.
Exception is when NLM_F_REPLACE flag is given without NLM_F_CREATE, and
no matching route is found. In this case it should be safe to assume
that the request issuer is familiar with NLM_F_* flags, and does really
not want route to be created.
Specifying NLM_F_REPLACE flag will now make the kernel to search for
matching route, and replace it with new one. If no route is found and
NLM_F_CREATE is specified as well, then new route is created.
Also, specifying NLM_F_EXCL will yield returning of error if matching
route is found.
Patch created against linux-3.2-rc1
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Mon, 14 Nov 2011 08:13:25 +0000 (08:13 +0000)]
Sweep the last of the active .get_drvinfo floors under ethernet/
This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy. It also does a modicum of other
cleaning in those routines.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 14 Nov 2011 06:05:34 +0000 (06:05 +0000)]
bnx2x: uses build_skb() in receive path
bnx2x uses following formula to compute its rx_buf_sz :
dev->mtu + 2*L1_CACHE_BYTES + 14 + 8 + 8 + 2
Then core network adds NET_SKB_PAD and SKB_DATA_ALIGN(sizeof(struct
skb_shared_info))
Final allocated size for skb head on x86_64 (L1_CACHE_BYTES = 64,
MTU=1500) : 2112 bytes : SLUB/SLAB round this to 4096 bytes.
Since skb truesize is then bigger than SK_MEM_QUANTUM, we have lot of
false sharing because of mem_reclaim in UDP stack.
One possible way to half truesize is to reduce the need by 64 bytes
(2112 -> 2048 bytes)
Instead of allocating a full cache line at the end of packet for
alignment, we can use the fact that skb_shared_info sits at the end of
skb->head, and we can use this room, if we convert bnx2x to new
build_skb() infrastructure.
skb_shared_info will be initialized after hardware finished its
transfert, so we can eventually overwrite the final padding.
Using build_skb() also reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are recycled while still hot.
Performance results :
(820.000 pps on a rx UDP monothread benchmark, instead of 720.000 pps)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Eilon Greenstein <eilong@broadcom.com> CC: Ben Hutchings <bhutchings@solarflare.com> CC: Tom Herbert <therbert@google.com> CC: Jamal Hadi Salim <hadi@mojatatu.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Thomas Graf <tgraf@infradead.org> CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 14 Nov 2011 06:03:34 +0000 (06:03 +0000)]
net: introduce build_skb()
One of the thing we discussed during netdev 2011 conference was the idea
to change some network drivers to allocate/populate their skb at RX
completion time, right before feeding the skb to network stack.
In old days, we allocated skbs when populating the RX ring.
This means bringing into cpu cache sk_buff and skb_shared_info cache
lines (since we clear/initialize them), then 'queue' skb->data to NIC.
By the time NIC fills a frame in skb->data buffer and host can process
it, cpu probably threw away the cache lines from its caches, because lot
of things happened between the allocation and final use.
So the deal would be to allocate only the data buffer for the NIC to
populate its RX ring buffer. And use build_skb() at RX completion to
attach a data buffer (now filled with an ethernet frame) to a new skb,
initialize the skb_shared_info portion, and give the hot skb to network
stack.
build_skb() is the function to allocate an skb, caller providing the
data buffer that should be attached to it. Drivers are expected to call
skb_reserve() right after build_skb() to adjust skb->data to the
Ethernet frame (usually skipping NET_SKB_PAD and NET_IP_ALIGN, but some
drivers might add a hardware provided alignment)
Data provided to build_skb() MUST have been allocated by a prior
kmalloc() call, with enough room to add SKB_DATA_ALIGN(sizeof(struct
skb_shared_info)) bytes at the end of the data without corrupting
incoming frame.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Eilon Greenstein <eilong@broadcom.com> CC: Ben Hutchings <bhutchings@solarflare.com> CC: Tom Herbert <therbert@google.com> CC: Jamal Hadi Salim <hadi@mojatatu.com> CC: Stephen Hemminger <shemminger@vyatta.com> CC: Thomas Graf <tgraf@infradead.org> CC: Herbert Xu <herbert@gondor.apana.org.au> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds listen only mode to the mscan controller.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 9 Nov 2011 12:07:14 +0000 (12:07 +0000)]
neigh: new unresolved queue limits
Le mercredi 09 novembre 2011 à 16:21 -0500, David Miller a écrit :
> From: David Miller <davem@davemloft.net>
> Date: Wed, 09 Nov 2011 16:16:44 -0500 (EST)
>
> > From: Eric Dumazet <eric.dumazet@gmail.com>
> > Date: Wed, 09 Nov 2011 12:14:09 +0100
> >
> >> unres_qlen is the number of frames we are able to queue per unresolved
> >> neighbour. Its default value (3) was never changed and is responsible
> >> for strange drops, especially if IP fragments are used, or multiple
> >> sessions start in parallel. Even a single tcp flow can hit this limit.
> > ...
> >
> > Ok, I've applied this, let's see what happens :-)
>
> Early answer, build fails.
>
> Please test build this patch with DECNET enabled and resubmit. The
> decnet neigh layer still refers to the removed ->queue_len member.
>
> Thanks.
Ouch, this was fixed on one machine yesterday, but not the other one I
used this morning, sorry.
[PATCH V5 net-next] neigh: new unresolved queue limits
unres_qlen is the number of frames we are able to queue per unresolved
neighbour. Its default value (3) was never changed and is responsible
for strange drops, especially if IP fragments are used, or multiple
sessions start in parallel. Even a single tcp flow can hit this limit.
$ arp -d 192.168.20.108 ; ping -c 2 -s 8000 192.168.20.108
PING 192.168.20.108 (192.168.20.108) 8000(8028) bytes of data.
8008 bytes from 192.168.20.108: icmp_seq=2 ttl=64 time=0.322 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
More changes to the recent code to support control of forwarding
database via netlink.
* Support NTF_USE like neighbour table
* Validate state bits from application
* Only send notifications (and change bits) if new entry is
different.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Wed, 9 Nov 2011 09:58:07 +0000 (09:58 +0000)]
Sweep additional floors of strcpy in .get_drvinfo routines
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Fri, 11 Nov 2011 05:10:39 +0000 (05:10 +0000)]
fsl_pq_mdio: Clean up tbi address configuration
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sanjay Hortikar [Fri, 11 Nov 2011 16:11:21 +0000 (16:11 +0000)]
net-forcedeth: Add internal loopback support for forcedeth NICs.
Support enabling/disabling/querying internal loopback mode for
forcedeth NICs using ethtool.
Signed-off-by: Sanjay Hortikar <horti@google.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes settings for device initialization which makes possible to
use NDISC and TCP.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables debug output enabled by default.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 13 Nov 2011 01:24:04 +0000 (01:24 +0000)]
ipv6: reduce percpu needs for icmpv6msg mibs
Reading /proc/net/snmp6 on a machine with a lot of cpus is very
expensive (can be ~88000 us).
This is because ICMPV6MSG MIB uses 4096 bytes per cpu, and folding
values for all possible cpus can read 16 Mbytes of memory (32MBytes on
non x86 arches)
ICMP messages are not considered as fast path on a typical server, and
eventually few cpus handle them anyway. We can afford an atomic
operation instead of using percpu data.
This saves 4096 bytes per cpu and per network namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 11 Nov 2011 22:16:48 +0000 (22:16 +0000)]
net: introduce ethernet teaming device
This patch introduces new network device called team. It supposes to be
very fast, simple, userspace-driven alternative to existing bonding
driver.
Userspace library called libteam with couple of demo apps is available
here:
https://github.com/jpirko/libteam
Note it's still in its dipers atm.
team<->libteam use generic netlink for communication. That and rtnl
suppose to be the only way to configure team device, no sysfs etc.
Python binding of libteam was recently introduced.
Daemon providing arpmon/miimon active-backup functionality will be
introduced shortly. All what's necessary is already implemented in
kernel team driver.
v7->v8:
- check ndo_ndo_vlan_rx_[add/kill]_vid functions before calling
them.
- use dev_kfree_skb_any() instead of dev_kfree_skb()
v6->v7:
- transmit and receive functions are not checked in hot paths.
That also resolves memory leak on transmit when no port is
present
v5->v6:
- changed couple of _rcu calls to non _rcu ones in non-readers
v4->v5:
- team_change_mtu() uses team->lock while travesing though port
list
- mac address changes are moved completely to jurisdiction of
userspace daemon. This way the daemon can do FOM1, FOM2 and
possibly other weird things with mac addresses.
Only round-robin mode sets up all ports to bond's address then
enslaved.
- Extended Kconfig text
v3->v4:
- remove redundant synchronize_rcu from __team_change_mode()
- revert "set and clear of mode_ops happens per pointer, not per
byte"
- extend comment of function __team_change_mode()
v2->v3:
- team_change_mtu() uses rcu version of list traversal to unwind
- set and clear of mode_ops happens per pointer, not per byte
- port hashlist changed to be embedded into team structure
- error branch in team_port_enter() does cleanup now
- fixed rtln->rtnl
v1->v2:
- modes are made as modules. Makes team more modular and
extendable.
- several commenters' nitpicks found on v1 were fixed
- several other bugs were fixed.
- note I ignored Eric's comment about roundrobin port selector
as Eric's way may be easily implemented as another mode (mode
"random") in future.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:32 +0000 (04:34 +0000)]
bnx2x: update driver version to 1.70.35-0
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Sun, 13 Nov 2011 04:34:31 +0000 (04:34 +0000)]
bnx2x: Remove on-stack napi struct variable
Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:30 +0000 (04:34 +0000)]
bnx2x: prevent race in statistics flow
The race may cause access of registers while MAC hw block is
in reset state. As a result syslog will show error messages.
We can prevent this by using state from local variable.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Sun, 13 Nov 2011 04:34:29 +0000 (04:34 +0000)]
bnx2x: add fan failure event handling
Shut down the device in case of fan failure to prevent HW damage.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:28 +0000 (04:34 +0000)]
bnx2x: remove unused #define
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:27 +0000 (04:34 +0000)]
bnx2x: simplify definition of RX_SGE_MASK_LEN and use it.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:26 +0000 (04:34 +0000)]
bnx2x: DCBX: use #define instead of magic
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:25 +0000 (04:34 +0000)]
bnx2x: propagate DCBX negotiation
We need propagate the DCBX results from PMF to other functions
on the same port, in order to properly update netdev structure
and allow following new ETS and PFC configurations.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:24 +0000 (04:34 +0000)]
bnx2x: separate FCoE and iSCSI license initialization.
FCoE license info must be initialized at probe(), but
iSCSI at open().
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:23 +0000 (04:34 +0000)]
bnx2x: remove unused variable
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:22 +0000 (04:34 +0000)]
bnx2x: use rx_queue index for skb_record_rx_queue()
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 13 Nov 2011 04:34:21 +0000 (04:34 +0000)]
bnx2x: allow FCoE and DCB for 578xx
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Thu, 10 Nov 2011 19:18:00 +0000 (19:18 +0000)]
be2net: stop issuing FW cmds if any cmd times out
A FW cmd timeout (with a sufficiently large timeout value in the
order of tens of seconds) indicates an unresponsive FW. In this state
issuing further cmds and waiting for a completion will only stall the process.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Thu, 10 Nov 2011 19:17:57 +0000 (19:17 +0000)]
be2net: init (vf)_if_handle/vf_pmac_id to handle failure scenarios
Initialize if_handle, vf_if_handle and vf_pmac_id with "-1" so that in
failure cases when be_clear() is called, we can skip over
if_destroy/pmac_del cmds if they have not been created.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 9 Nov 2011 07:24:35 +0000 (07:24 +0000)]
ipv4: PKTINFO doesnt need dst reference
Le lundi 07 novembre 2011 à 15:33 +0100, Eric Dumazet a écrit :
> At least, in recent kernels we dont change dst->refcnt in forwarding
> patch (usinf NOREF skb->dst)
>
> One particular point is the atomic_inc(dst->refcnt) we have to perform
> when queuing an UDP packet if socket asked PKTINFO stuff (for example a
> typical DNS server has to setup this option)
>
> I have one patch somewhere that stores the information in skb->cb[] and
> avoid the atomic_{inc|dec}(dst->refcnt).
>
OK I found it, I did some extra tests and believe its ready.
[PATCH net-next] ipv4: IP_PKTINFO doesnt need dst reference
When a socket uses IP_PKTINFO notifications, we currently force a dst
reference for each received skb. Reader has to access dst to get needed
information (rt_iif & rt_spec_dst) and must release dst reference.
We also forced a dst reference if skb was put in socket backlog, even
without IP_PKTINFO handling. This happens under stress/load.
We can instead store the needed information in skb->cb[], so that only
softirq handler really access dst, improving cache hit ratios.
This removes two atomic operations per packet, and false sharing as
well.
On a benchmark using a mono threaded receiver (doing only recvmsg()
calls), I can reach 720.000 pps instead of 570.000 pps.
IP_PKTINFO is typically used by DNS servers, and any multihomed aware
UDP application.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Nov 2011 13:04:43 +0000 (13:04 +0000)]
ipv4: reduce percpu needs for icmpmsg mibs
Reading /proc/net/snmp on a machine with a lot of cpus is very expensive
(can be ~88000 us).
This is because ICMPMSG MIB uses 4096 bytes per cpu, and folding values
for all possible cpus can read 16 Mbytes of memory.
ICMP messages are not considered as fast path on a typical server, and
eventually few cpus handle them anyway. We can afford an atomic
operation instead of using percpu data.
This saves 4096 bytes per cpu and per network namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Nov 2011 22:07:07 +0000 (17:07 -0500)]
net: rename sk_clone to sk_clone_lock
Make clear that sk_clone() and inet_csk_clone() return a locked socket.
Add _lock() prefix and kerneldoc.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This just makes it possible to spoof source IPv6 address on a socket
without having to create and bind a new socket for every source IP
we wish to spoof.
Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This makes native ipv6 bind follow the precedent set by:
- native ipv4 bind behaviour
- dual stack ipv4-mapped ipv6 bind behaviour.
This does allow an unpriviledged process to spoof its source IPv6
address, just like it currently can spoof its source IPv4 address
(for example when using UDP).
Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Jones [Mon, 7 Nov 2011 13:29:27 +0000 (13:29 +0000)]
sweep the floors and convert some .get_drvinfo routines to strlcpy
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Tue, 11 Oct 2011 01:12:02 +0000 (01:12 +0000)]
ipv4: Fix inetpeer expire time information
As we update the learned pmtu informations on demand, we might
report a nagative expiration time value to userspace if the
pmtu informations are already expired and we have not send a
packet to that inetpeer after expiration. With this patch we
send a expire time of null to userspace after expiration
until the next packet is send to that inetpeer.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
oftedal [Mon, 7 Nov 2011 11:47:53 +0000 (11:47 +0000)]
sunhme: Allow usage on SBI based SBus systems
To prevent the SBus driver for Sun Happy Meal cards from being loaded for
PCI cards utilizing the same chipset, a filter was added to the probe
function in commit 0b492fce3d72d982a7981905f85484a1e1ba7fde.
The filter was implemented by checking the name of the parent node in
the OF tree. This patch extends this filter, so that the driver will
load on SBus systems that are based upon SBI SBus Bridges.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nico Erfurth [Tue, 8 Nov 2011 07:30:40 +0000 (07:30 +0000)]
Fix incorrect usage of NET_IP_ALIGN
The driver used NET_IP_ALIGN to remove some additional padding inside of
the rx_fixup function. On many architectures NET_IP_ALIGN defaults to 2
which removed the correct amount of bytes.
On MCORE2-machines commit ea812ca1b06113597adcd8e70c0f84a413d97544
introduces a change which sets NET_IP_ALIGN to 0 by default. Which
triggered the bug on these machines.
This fix introduces a new RXW_PADDING define and uses this instead of
NET_IP_ALIGN. The name was taken from the original SMSC7500 driver which
is provided by SMSC.
Signed-off-by: Nico Erfurth <ne@erfurth.eu> Tested-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Haley [Tue, 8 Nov 2011 04:41:42 +0000 (04:41 +0000)]
ipv6: drop packets when source address is multicast
RFC 4291 Section 2.7 says Multicast addresses must not be used as source
addresses in IPv6 packets - drop them on input so we don't process the
packet further.
Signed-off-by: Brian Haley <brian.haley@hp.com> Reported-and-Tested-by: Kumar Sanghvi <divinekumar@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Mon, 7 Nov 2011 20:44:37 +0000 (20:44 +0000)]
r8169: increase the delay parameter of pm_schedule_suspend
The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 8 Nov 2011 00:16:02 +0000 (16:16 -0800)]
Linux 3.2-rc1
.. with new name. Because nothing says "really solid kernel release"
like naming it after an extinct animal that just happened to be in the
news lately.
Al Viro [Mon, 7 Nov 2011 21:21:26 +0000 (21:21 +0000)]
VFS: we need to set LOOKUP_JUMPED on mountpoint crossing
Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.
Linus Torvalds [Mon, 7 Nov 2011 20:38:11 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Fix live annotation in the --stdio interface
perf top tui: Don't recalc column widths considering just the first page
perf report: Add progress bar when processing time ordered events
perf hists browser: Warn about lost events
perf tools: Fix a typo of command name as trace-cmd
perf hists: Fix recalculation of total_period when sorting entries
perf header: Fix build on old systems
perf ui browser: Handle K_RESIZE in dialog windows
perf ui browser: No need to switch char sets that often
perf hists browser: Use K_TIMER
perf ui: Rename ui__warning_paranoid to ui__error_paranoid
perf ui: Reimplement the popup windows using libslang
perf ui: Reimplement ui__popup_menu using ui__browser
perf ui: Reimplement ui_helpline using libslang
perf ui: Improve handling sigwinch a bit
perf ui progress: Reimplement using slang
perf evlist: Fix grouping of multiple events
Tony Lindgren [Mon, 7 Nov 2011 20:27:10 +0000 (12:27 -0800)]
ARM: OMAP: Fix export.h or module.h includes
Commit 32aaeffbd4a7457bf2f7448b33b5946ff2a960eb (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
Axel Lin [Mon, 7 Nov 2011 20:27:10 +0000 (12:27 -0800)]
ARM: OMAP: omap_device: Include linux/export.h
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
david decotigny [Sat, 5 Nov 2011 14:38:24 +0000 (14:38 +0000)]
forcedeth: fix a few sparse warnings (variable shadowing)
This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mandeep Baines [Sat, 5 Nov 2011 14:38:23 +0000 (14:38 +0000)]
forcedeth: Improve stats counters
Rx byte count was off; instead use the hardware's count. Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.
- The count of transmitted packets reported by the forcedeth driver
reports pre-TSO (TCP Segmentation Offload) packet counts and not the
count of the number of packets sent on the wire. This change fixes
the forcedeth driver to report the correct count. Fixed the code by
copying the count stored in the NIC H/W to the value reported by the
driver.
- Count rx_drop_frame errors as rx_fifo_errors:
We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
for too long. Normally, rx_fifo_errors would be counted in this case.
The rx_drop_frame error count is private to forcedeth and is not
reported by ifconfig or sysfs. The rx_fifo_errors count is currently
unused in the forcedeth driver. It is reported by ifconfig as overruns.
This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
david decotigny [Sat, 5 Nov 2011 14:38:22 +0000 (14:38 +0000)]
forcedeth: remove unneeded stats updates
Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.
Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Ditto [Sat, 5 Nov 2011 14:38:21 +0000 (14:38 +0000)]
forcedeth: Acknowledge only interrupts that are being processed
This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process. This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: David Decotigny <david.decotigny@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
david decotigny [Sat, 5 Nov 2011 14:38:20 +0000 (14:38 +0000)]
forcedeth: fix race when unloading module
When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().
Tested:
x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
+ rmmod/modprobe/ifconfig in a loop
Paul Gortmaker [Wed, 28 Sep 2011 22:29:32 +0000 (18:29 -0400)]
drivers/md: change module.h -> export.h in persistent-data/dm-*
For the files which are not themselves modular, we can change
them to include only the smaller export.h since all they are
doing is looking for EXPORT_SYMBOL.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Gortmaker [Sun, 9 Oct 2011 03:24:48 +0000 (23:24 -0400)]
arm: Add export.h to recently added files for EXPORT_SYMBOL
These files didn't exist at the time of the module.h split, and
so were not fixed by the commits on that baseline. Since they use
the EXPORT_SYMBOL and/or THIS_MODULE macros, they will need the
new export.h file included that provides them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the bug added in commit v3.1-rc7-1055-gf9b491e
SKB can be NULL at this point, at least for cdc-ncm.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 7 Nov 2011 18:13:52 +0000 (10:13 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
Linus Torvalds [Mon, 7 Nov 2011 18:01:56 +0000 (10:01 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
vmwgfx: Snoop DMA transfers with non-covering sizes
vmwgfx: Move the prefered mode first in the list
vmwgfx: Unreference surface on cursor error path
vmwgfx: Free prefered mode on error path
vmwgfx: Use pointer return error codes
vmwgfx: Fix hw cursor position
vmwgfx: Infrastructure for explicit placement
vmwgfx: Make the preferred autofit mode have a 60Hz vrefresh
vmwgfx: Remove screen object active list
vmwgfx: Screen object cleanups
drm/radeon/kms: consolidate GART code, fix segfault after GPU lockup V2
drm/radeon/kms: don't poll forever if MC GDDR link training fails
drm/radeon/kms: fix DP setup on TRAVIS bridges
drm/radeon/kms: set HPD polarity in hpd_init()
drm/radeon/kms: add MSI module parameter
drm/radeon/kms: Add MSI quirk for Dell RS690
drm/radeon/kms: Add MSI quirk for HP RS690
drm/radeon/kms: split MSI check into a separate function
vmwgfx: Reinstate the update_layout ioctl
drm/radeon/kms: always do extended edid probe
...
Linus Torvalds [Mon, 7 Nov 2011 17:11:16 +0000 (09:11 -0800)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
vmwgfx: Snoop DMA transfers with non-covering sizes
Enough to get cursors working under Wayland.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Make it possible to use explicit placement
(although not hooked up with a user-space interface yet)
and relax the single framebuffer limit to only apply to implicit placement.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
projects / karo-tx-linux.git / log