We hit this panic on a few of our boxes this week where we have an
ordered_extent with an NULL inode. We do an igrab() of the inode in writepages,
but weren't doing it in writepage which can be called directly from the VM on
dirty pages. If the inode has been unlinked then we could have I_FREEING set
which means igrab() would return NULL and we get this panic. Fix this by trying
to igrab in btrfs_writepage, and if it returns NULL then just redirty the page
and return AOP_WRITEPAGE_ACTIVATE; so the VM knows it wasn't successful. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like oversight, call brelse() when checksum fails. Further down the
code, in the non error path, we do call brelse() and so we don't see
brelse() in the goto error paths.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel now always uses vector registers when available, however KVM
has special logic if support is really enabled for a guest. If support
is disabled, guest_fpregs.fregs will only contain memory for the fpu.
The kernel, however, will store vector registers into that area,
resulting in crazy memory overwrites.
Simply extending that area is not enough, because the format of the
registers also changes. We would have to do additional conversions, making
the code even more complex. Therefore let's directly use one place for
the vector/fpu registers + fpc (in kvm_run). We just have to convert the
data properly when accessing it. This makes current code much easier.
Please note that vector/fpu registers are now always stored to
vcpu->run->s.regs.vrs. Although this data is visible to QEMU and
used for migration, we only guarantee valid values to user space when
KVM_SYNC_VRS is set. As that is only the case when we have vector
register support, we are on the safe side.
Fixes: b5510d9b68c3 ("s390/fpu: always enable the vector facility if it is available") Cc: stable@vger.kernel.org # v4.4 d9a3a09af54d s390/kvm: remove dependency on struct save_area definition Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[adopt to d9a3a09af54d] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt8500 clocksource driver declares itself as capable to handle the
minimum delay of 4 cycles by passing the value into
clockevents_config_and_register(). The vt8500_timer_set_next_event()
requires the passed cycles value to be at least 16. The impact is that
userspace hangs in nanosleep() calls with small delay intervals.
This problem is reproducible in Linux 4.2 starting from: c6eb3f70d448 ('hrtimer: Get rid of hrtimer softirq')
From Russell King, more detailed explanation:
"It's a speciality of the StrongARM/PXA hardware. It takes a certain
number of OSCR cycles for the value written to hit the compare registers.
So, if a very small delta is written (eg, the compare register is written
with a value of OSCR + 1), the OSCR will have incremented past this value
before it hits the underlying hardware. The result is, that you end up
waiting a very long time for the OSCR to wrap before the event fires.
So, we introduce a check in set_next_event() to detect this and return
-ETIME if the calculated delta is too small, which causes the generic
clockevents code to retry after adding the min_delta specified in
clockevents_config_and_register() to the current time value.
min_delta must be sufficient that we don't re-trip the -ETIME check - if
we do, we will return -ETIME, forward the next event time, try to set it,
return -ETIME again, and basically lock the system up. So, min_delta
must be larger than the check inside set_next_event(). A factor of two
was chosen to ensure that this situation would never occur.
The PXA code worked on PXA systems for years, and I'd suggest no one
changes this mechanism without access to a wide range of PXA systems,
otherwise they're risking breakage."
Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Alexey Charkov <alchark@gmail.com> Signed-off-by: Roman Volkov <rvolkov@v1ros.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71f64340fc0e changed the handling of irq_desc->action from
CPU 0 CPU 1
free_irq() lock(desc)
lock(desc) handle_edge_irq()
if (desc->action) {
handle_irq_event()
action = desc->action
unlock(desc)
desc->action = NULL handle_irq_event_percpu(desc, action)
action->xxx
to
CPU 0 CPU 1
free_irq() lock(desc)
lock(desc) handle_edge_irq()
if (desc->action) {
handle_irq_event()
unlock(desc)
desc->action = NULL handle_irq_event_percpu(desc, action)
action = desc->action
action->xxx
So if free_irq manages to set the action to NULL between the unlock and before
the readout, we happily dereference a null pointer.
We could simply revert 71f64340fc0e, but we want to preserve the better code
generation. A simple solution is to change the action loop from a do {} while
to a while {} loop.
This is safe because we either see a valid desc->action or NULL. If the action
is about to be removed it is still valid as free_irq() is blocked on
synchronize_irq().
That's basically the same mechanism as we have for shared
interrupts. action->next can become NULL while handle_irq_event_percpu()
runs. Either it sees the action or NULL. It does not matter, because action
itself cannot go away before the interrupt in progress flag has been cleared.
Fixes: commit 71f64340fc0e "genirq: Remove the second parameter from handle_irq_event_percpu()" Reported-by: zyjzyj2000@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Huang Shijie <shijie.huang@arm.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1601131224190.3575@nanos Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4167e9b2cf10 ("mm: remove GFP_THISNODE") removed the GFP_THISNODE
flag combination due to confusing semantics. It noted that
alloc_misplaced_dst_page() was one such user after changes made by
commit e97ca8e5b864 ("mm: fix GFP_THISNODE callers and clarify").
Unfortunately when GFP_THISNODE was removed, users of
alloc_misplaced_dst_page() started waking kswapd and entering direct
reclaim because the wrong GFP flags are cleared. The consequence is
that workloads that used to fit into memory now get reclaimed which is
addressed by this patch.
The problem can be demonstrated with "mutilate" that exercises memcached
which is software dedicated to memory object caching. The configuration
uses 80% of memory and is run 3 times for varying numbers of clients.
The results on a 4-socket NUMA box are
The metric is queries/second with the more the better. The results are
way outside of the noise and the reason for the improvement is obvious
from some of the vmstats
The vanilla kernel is swapping like crazy with large amounts of direct
reclaim and kswapd activity. The figures are aggregate but it's known
that the bad activity is throughout the entire test.
Note that simple streaming anon/file memory consumers also see this
problem but it's not as obvious. In those cases, kswapd is awake when
it should not be.
As there are at least two reclaim-related bugs out there, it's worth
spelling out the user-visible impact. This patch only addresses bugs
related to excessive reclaim on NUMA hardware when the working set is
larger than a NUMA node. There is a bug related to high kswapd CPU
usage but the reports are against laptops and other UMA hardware and is
not addressed by this patch.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pmd_trans_unstable()/pmd_none_or_trans_huge_or_clear_bad() were
introduced to locklessy (but atomically) detect when a pmd is a regular
(stable) pmd or when the pmd is unstable and can infinitely transition
from pmd_none() and pmd_trans_huge() from under us, while only holding
the mmap_sem for reading (for writing not).
While holding the mmap_sem only for reading, MADV_DONTNEED can run from
under us and so before we can assume the pmd to be a regular stable pmd
we need to compare it against pmd_none() and pmd_trans_huge() in an
atomic way, with pmd_trans_unstable(). The old pmd_trans_huge() left a
tiny window for a race.
Useful applications are unlikely to notice the difference as doing
MADV_DONTNEED concurrently with a page fault would lead to undefined
behavior.
[akpm@linux-foundation.org: tidy up comment grammar/layout] Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing append direct io cleanup, if deleting inode fails, it goes
out without unlocking inode, which will cause the inode deadlock.
This issue was introduced by commit cf1776a9e834 ("ocfs2: fix a tiny
race when truncate dio orohaned entry").
Signed-off-by: Guozhonghua <guozhonghua@h3c.com> Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Reviewed-by: Gang He <ghe@suse.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get tons of cases where the master interrupt handler apparently set
a bit, with the SDEIIR disagreeing. No idea what's going on there, but
it's consistent on gen8+, no one seems to care about it and it's
making CI results flaky.
Shut it up.
No idea what's going on here, but we've had fun with PCH interrupts
before:
drm/i915: also disable south interrupts when handling them
Note that there's a regression report in Bugzilla, and other
regression reports on the mailing lists keep croping up. But no ill
effects have ever been reported. But for paranoia still keep the
message at a debug level as a breadcrumb, just in case.
The cxgb3_*_send() functions return NET_XMIT_ values, which are
positive integers values. So don't treat positive return values
as an error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
[a pox on developers and maintainers who do not cc: stable for bug fixes like this - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally the setup function will be called multiple times. Only request
the gpio the first time otherwise -EBUSY will occur on subsequent calls to
setup.
Reported-by: Joseph Bell <joe@iachieved.it> Signed-off-by: Michael Welling <mwelling@ieee.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's one point was missed in the patch commit da49889deb34 ("staging:
binder: Support concurrent 32 bit and 64 bit processes."). When configure
BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of
void * is 64bit on 64bit system. Correct it here.
Signed-off-by: Lisa Du <cldu@marvell.com> Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Fixes: da49889deb34 ("staging: binder: Support concurrent 32 bit and 64 bit processes.") Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda6187181 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Reported-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a thin pool is being destroyed delayed work items are
cancelled using cancel_delayed_work(), which doesn't guarantee that on
return the delayed item isn't running. This can cause the work item to
requeue itself on an already destroyed workqueue. Fix this by using
cancel_delayed_work_sync() which guarantees that on return the work item
is not running anymore.
Fixes: 905e51b39a555 ("dm thin: commit outstanding data every second") Fixes: 85ad643b7e7e5 ("dm thin: add timeout to stop out-of-data-space mode holding IO forever") Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, it would only scan the entire disk if it was starting from
the very start of the disk - i.e. if the previous scan got to the end.
This was broken by refill_full_stripes(), which updates last_scanned so
that refill_dirty was never triggering the searched_from_start path.
But if we change refill_dirty() to always scan the entire disk if
necessary, regardless of what last_scanned was, the code gets cleaner
and we fix that bug too.
Added a safeguard in the shutdown case. At least while not being
attached it is also possible to trigger a kernel bug by writing into
writeback_running. This change adds the same check before trying to
wake up the thread for that case.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows to use register, not register_quiet in udev to avoid "device_busy" error.
The initial patch proposed at https://lkml.org/lkml/2013/8/26/549 by Gabriel de Perthuis
<g2p.code@gmail.com> does not unlock the mutex and hangs the kernel.
See http://thread.gmane.org/gmane.linux.kernel.bcache.devel/2594 for the discussion.
Cc: Denis Bychkov <manover@gmail.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Gabriel de Perthuis <g2p.code@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We forget to clear BCACHE_DEV_UNLINK_DONE flag in bcache_device_attach()
function when we attach a backing device first time. After detaching this
backing device, this flag will be true and sysfs_remove_link() isn't called in
bcache_device_unlink(). Then when we attach this backing device again,
sysfs_create_link() will return EEXIST error in bcache_device_link().
So the fix is trival and we clear this flag in bcache_device_link().
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Tested-by: Joshua Schmid <jschmid@suse.com> Tested-by: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Kent Overstreet <kmo@daterainc.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subject : [PATCH v2] bcache: fix a livelock in btree lock
Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM)
This commit tries to fix a livelock in bcache. This livelock might
happen when we causes a huge number of cache misses simultaneously.
When we get a cache miss, bcache will execute the following path.
->cached_dev_make_request()
->cached_dev_read()
->cached_lookup()
->bch->btree_map_keys()
->btree_root() <------------------------
->bch_btree_map_keys_recurse() |
->cache_lookup_fn() |
->cached_dev_cache_miss() |
->bch_btree_insert_check_key() -|
[If btree->seq is not equal to seq + 1, we should return
EINTR and traverse btree again.]
In bch_btree_insert_check_key() function we first need to check upgrade
flag (op->lock == -1), and when this flag is true we need to release
read btree->lock and try to take write btree->lock. During taking and
releasing this write lock, btree->seq will be monotone increased in
order to prevent other threads modify this in cache miss (see btree.h:74).
But if there are some cache misses caused by some requested, we could
meet a livelock because btree->seq is always changed by others. Thus no
one can make progress.
This commit will try to take write btree->lock if it encounters a race
when we traverse btree. Although it sacrifice the scalability but we
can ensure that only one can modify the btree.
'This is because the pstore filesystem can be backed by UEFI variables,
and (for example) a crash might dump the last kilobytes of the dmesg
into a number of pstore entries, each entry backed by a separate UEFI
variable in the above GUID namespace, and with a variable name
according to the above pattern.
Please see "drivers/firmware/efi/efi-pstore.c".
While this patch series will not prevent the user from deleting those
UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
entry will continue to delete the backing UEFI variable), I think it
would be nice to preserve the possibility for the sysadmin to delete
Linux-created UEFI variables that carry portions of the crash log,
*without* having to mount the pstore filesystem.'
There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.
Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.
Reported-by: Laszlo Ersek <lersek@redhat.com> Acked-by: Peter Jones <pjones@redhat.com> Tested-by: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"rm -rf" is bricking some peoples' laptops because of variables being
used to store non-reinitializable firmware driver data that's required
to POST the hardware.
These are 100% bugs, and they need to be fixed, but in the mean time it
shouldn't be easy to *accidentally* brick machines.
We have to have delete working, and picking which variables do and don't
work for deletion is quite intractable, so instead make everything
immutable by default (except for a whitelist), and make tools that
aren't quite so broad-spectrum unset the immutable flag.
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the variables in this list so far are defined to be in the global
namespace in the UEFI spec, so this just further ensures we're
validating the variables we think we are.
Including the guid for entries will become more important in future
patches when we decide whether or not to allow deletion of variables
based on presence in this list.
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Actually translate from ucs2 to utf8 before doing the test, and then
test against our other utf8 data, instead of fudging it.
Signed-off-by: Peter Jones <pjones@redhat.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Translate EFI's UCS-2 variable names to UTF-8 instead of just assuming
all variable names fit in ASCII.
Signed-off-by: Peter Jones <pjones@redhat.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds ucs2_utf8size(), which tells us how big our ucs2 string is in
bytes, and ucs2_as_utf8, which translates from ucs2 to utf8..
Signed-off-by: Peter Jones <pjones@redhat.com> Tested-by: Lee, Chun-Yi <jlee@suse.com> Acked-by: Matthew Garrett <mjg59@coreos.com> Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PSCI SMP implementation is built only when both CONFIG_SMP and
CONFIG_ARM_PSCI are set, so a configuration that has the latter
but not the former can get a link error when it tries to call
psci_smp_available().
arch/arm/mach-tegra/built-in.o: In function `tegra114_cpuidle_init':
cpuidle-tegra114.c:(.init.text+0x52a): undefined reference to `psci_smp_available'
This corrects the #ifdef in the psci.h header file to match the
Makefile conditional we have for building that function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_memremap() returns an ERR_PTR() value in case of error.
However, it returns NULL when memremap() failed. This causes
the caller, such as the pmem driver, to proceed and oops later.
Change devm_memremap() to return ERR_PTR(-ENXIO) when memremap()
failed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Cc: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC6 (and Linaro's 2015.12 snapshot of GCC5) has a new default that uses
adrp/ldr or adrp/add to address literal pools. When CONFIG_ARM64_ERRATUM_843419
is enabled, modules built with this toolchain fail to load:
module libahci: unsupported RELA relocation: 275
This patch fixes the problem by passing '-mpc-relative-literal-loads'
to the compiler.
Cc: stable@vger.kernel.org Fixes: df057cc7b4fa ("arm64: errata: add module build workaround for erratum #843419") BugLink: http://bugs.launchpad.net/bugs/1533009 Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Suggested-by: Christophe Lyon <christophe.lyon@linaro.org> Signed-off-by: Dann Frazier <dann.frazier@canonical.com>
[will: backport to 4.4-stable] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that the DEBUG_UART_BCM63XX option is enabled whenever
the ARCH_BCM_63XX is, and that breaks multiplatform kernels because
we then end up using the UART address from BCM63XX rather than the
one we actually configured (if any).
This changes the BCM63XX options to only have one Kconfig option,
and only enable that if the user explicitly turns it on.
ext4 can update bh->b_state non-atomically in _ext4_get_block() and
ext4_da_get_block_prep(). Usually this is fine since bh is just a
temporary storage for mapping information on stack but in some cases it
can be fully living bh attached to a page. In such case non-atomic
update of bh->b_state can race with an atomic update which then gets
lost. Usually when we are mapping bh and thus updating bh->b_state
non-atomically, nobody else touches the bh and so things work out fine
but there is one case to especially worry about: ext4_finish_bio() uses
BH_Uptodate_Lock on the first bh in the page to synchronize handling of
PageWriteback state. So when blocksize < pagesize, we can be atomically
modifying bh->b_state of a buffer that actually isn't under IO and thus
can race e.g. with delalloc trying to map that buffer. The result is
that we can mistakenly set / clear BH_Uptodate_Lock bit resulting in the
corruption of PageWriteback state or missed unlock of BH_Uptodate_Lock.
Fix the problem by always updating bh->b_state bits atomically.
Reported-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Nikolay Borisov <kernel@kyup.com>
[NB: Backported to 4.4.2] Acked-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires. The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table). Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).
To fix this, we change the logic slightly. We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support. Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made. Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.
I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> CC: Dmitry Vyukov <dvyukov@google.com> CC: Vladislav Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value passed by unix_diag_get_exact to unix_lookup_by_ino has type
__u32, but unix_lookup_by_ino's argument ino has type int, which is not
a problem yet.
However, when ino is compared with sock_i_ino return value of type
unsigned long, ino is sign extended to signed long, and this results
to incorrect comparison on 64-bit architectures for inode numbers
greater than INT_MAX.
This bug was found by strace test suite.
Fixes: 5d3cae8bc39d ("unix_diag: Dumping exact socket core") Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tipc_bcast_unlock need to be unlocked in error path.
Signed-off-by: Insu Yun <wuninsu@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My implementation around IFF_NO_QUEUE driver flag assumed that leaving
tx_queue_len untouched (specifically: not setting it to zero) by drivers
would make it possible to assign a regular qdisc to them without having
to worry about setting tx_queue_len to a useful value. This was only
partially true: I overlooked that some drivers don't call ether_setup()
and therefore not initialize tx_queue_len to the default value of 1000.
Consequently, removing the workarounds in place for that case in qdisc
implementations which cared about it (namely, pfifo, bfifo, gred, htb,
plug and sfb) leads to problems with these specific interface types and
qdiscs.
Luckily, there's already a sanitization point for drivers setting
tx_queue_len to zero, which can be reused to assign the fallback value
most qdisc implementations used, which is 1.
Fixes: 348e3435cbefa ("net: sched: drop all special handling of tx_queue_len == 0") Tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0: (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1: (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2: (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.
We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.
Reported-by: Ilya Dryomov <idryomov@gmail.com> Fixes: ebb516af60e1 ("tcp/dccp: fix race at listener dismantle phase") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.
Fix this issue by checking and removing route cache when we get route.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
actions could change the etherproto in particular with ethernet
tunnelled data. Typically such actions, after peeling the outer header,
will ask for the packet to be reclassified. We then need to restart
the classification with the new proto header.
Example setup used to catch this:
sudo tc qdisc add dev $ETH ingress
sudo $TC filter add dev $ETH parent ffff: pref 1 protocol 802.1Q \
u32 match u32 0 0 flowid 1:1 \
action vlan pop reclassify
Fixes: 3b3ae880266d ("net: sched: consolidate tc_classify{,_compat}") Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop reference on the relay_po socket when __pppoe_xmit() succeeds.
This is already handled correctly in the error path.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous commit (33f72e6) added notification via netlink for tunnels
when created/modified/deleted. If the notification returned an error,
this error was returned from the tunnel function. If there were no
listeners, the error code ESRCH was returned, even though having no
listeners is not an error. Other calls to this and other similar
notification functions either ignore the error code, or filter ESRCH.
This patch checks for ESRCH and does not flag this as an error.
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.
Fixes: f4a1edd56120 ('net/mlx4_en: Advertize encapsulation offloads [...]') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d47010e ('net/mlx4_en: Add HW timestamping (TS) support') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94d6 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by: Amir Vadai <amir@vadai.me> Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.
The bug was added for IPv4 only.
Fixes: 079096f103fac ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 5266698661401a ("tipc: let broadcast packet reception
use new link receive function") we introduced a new per-node
broadcast reception link instance. This link is created at the
moment the node itself is created. Unfortunately, the allocation
is done after the node instance has already been added to the node
lookup hash table. This creates a potential race condition, where
arriving broadcast packets are able to find and access the node
before it has been fully initialized, and before the above mentioned
link has been created. The result is occasional crashes in the function
tipc_bcast_rcv(), which is trying to access the not-yet existing link.
We fix this by deferring the addition of the node instance until after
it has been fully initialized in the function tipc_node_create().
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Tested-by: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.
Callers are responsible for the freeing.
Many thanks to Dmitry for the report and diagnostic.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic in bond_arp_rcv will accept an incoming ARP for
validation if (a) the receiving slave is either "active" (which includes
the currently active slave, or the current ARP slave) or, (b) there is a
currently active slave, and it has received an ARP since it became active.
For case (b), the receiving slave isn't the currently active slave, and is
receiving the original broadcast ARP request, not an ARP reply from the
target.
This logic can fail if there is no currently active slave. In
this situation, the ARP probe logic cycles through all slaves, assigning
each in turn as the "current_arp_slave" for one arp_interval, then setting
that one as "active," and sending an ARP probe from that slave. The
current logic expects the ARP reply to arrive on the sending
current_arp_slave, however, due to switch FDB updating delays, the reply
may be directed to another slave.
This can arise if the bonding slaves and switch are working, but
the ARP target is not responding. When the ARP target recovers, a
condition may result wherein the ARP target host replies faster than the
switch can update its forwarding table, causing each ARP reply to be sent
to the previous current_arp_slave. This will never pass the logic in
bond_arp_rcv, as neither of the above conditions (a) or (b) are met.
Some experimentation on a LAN shows ARP reply round trips in the
200 usec range, but my available switches never update their FDB in less
than 4000 usec.
This patch changes the logic in bond_arp_rcv to additionally
accept an ARP reply for validation on any slave if there is a current ARP
slave and it sent an ARP probe during the previous arp_interval.
Fixes: aeea64ac717a ("bonding: don't trust arp requests unless active slave really works") Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ctx access is used, the kernel often needs to expand/rewrite
instructions, so after that patching, branch offsets have to be
adjusted for both forward and backward jumps in the new eBPF program,
but for backward jumps it fails to account the delta. Meaning, for
example, if the expansion happens exactly on the insn that sits at
the jump target, it doesn't fix up the back jump offset.
Analysis on what the check in adjust_branches() is currently doing:
/* adjust offset of jmps if necessary */
if (i < pos && i + insn->off + 1 > pos)
insn->off += delta;
else if (i > pos && i + insn->off + 1 < pos)
insn->off -= delta;
First case is if we cross pos-boundary and the jump instruction was
before pos. This is handeled correctly. I.e. if i == pos, then this
would mean our jump that we currently check was the patchlet itself
that we just injected. Since such patchlets are self-contained and
have no awareness of any insns before or after the patched one, the
delta is correctly not adjusted. Also, for the second condition in
case of i + insn->off + 1 == pos, means we jump to that newly patched
instruction, so no offset adjustment are needed. That part is correct.
Second interesting case is where we cross pos-boundary and the jump
instruction was after pos. Backward jump with i == pos would be
impossible and pose a bug somewhere in the patchlet, so the first
condition checking i > pos is okay only by itself. However, i +
insn->off + 1 < pos does not always work as intended to trigger the
adjustment. It works when jump targets would be far off where the
delta wouldn't matter. But, for example, where the fixed insn->off
before pointed to pos (target_Y), it now points to pos + delta, so
that additional room needs to be taken into account for the check.
This means that i) both tests here need to be adjusted into pos + delta,
and ii) for the second condition, the test needs to be <= as pos
itself can be a target in the backjump, too.
Fixes: 9bac3d6d548e ("bpf: allow extended BPF programs access skb fields") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue with unaligned accesses when using
eth_get_headlen on a page that was DMA aligned instead of being IP aligned.
The fact is when trying to check the length we don't need to be looking at
the flow label so we can reorder the checks to first check if we are
supposed to gather the flow label and then make the call to actually get
it.
v2: Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can
cause us to check for the flow label.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the unaligned accesses seen on GRE TEB tunnels when
generating hash keys. Specifically what this patch does is make it so that
we force the use of skb_copy_bits when the GRE inner headers will be
unaligned due to NET_IP_ALIGNED being a non-zero value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ed5a377d87dc ("sctp: translate host order to network order when
setting a hmacid") corrected the hmacid byte-order when setting a hmacid.
but the same issue also exists on getting a hmacid.
We fix it by changing hmacids to host order when users get them with
getsockopt.
Fixes: Commit ed5a377d87dc ("sctp: translate host order to network order when setting a hmacid") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware posts the devcmd result in result ring. In case of timeout, driver
does not increment the current result pointer and firmware could post the
result after timeout has occurred. During next devcmd, driver would be
reading the result of previous devcmd.
Fix this by incrementing result even in case of timeout.
Fixes: 373fb0873d43 ("enic: add devcmd2") Signed-off-by: Sandeep Pillai <sanpilla@cisco.com> Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.
tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.
This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.
v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com> Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petr Novopashenniy reported that ICMP redirects on SYN_RECV sockets
were leading to RST.
This is of course incorrect.
A specific list of ICMP messages should be able to drop a SYN_RECV.
For instance, a REDIRECT on SYN_RECV shall be ignored, as we do
not hold a dst per SYN_RECV pseudo request.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111751 Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table") Reported-by: Petr Novopashenniy <pety@rusnet.ru> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad406bb1 ("unix: properly account for FDs passed over unix sockets") Reported-by: David Herrmann <dh.herrmann@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silence lockdep false positive about rcu_dereference() being
used in the wrong context.
First one should use rcu_dereference_protected() as we own the spinlock.
Second one should be a normal assignation, as no barrier is needed.
Fixes: 18367681a10bd ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.") Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rcu stall with the following backtrace was seen on a system with
forwarding, optimistic_dad and use_optimistic set. To reproduce,
set these flags and allow ipv6 autoconf.
This occurs because the device write_lock is acquired while already
holding the read_lock. Back trace below -
v2: do addrconf_dad_kick inside read lock and then acquire write
lock for ipv6_ifa_notify as suggested by Eric
Fixes: 7fd2561e4ebdd ("net: ipv6: Add a sysctl to make optimistic
addresses useful candidates")
Cc: Eric Dumazet <edumazet@google.com> Cc: Erik Kline <ek@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the egress interface index specified via IPV6_PKTINFO
is ignored by __ip6_datagram_connect(), so that RFC 3542 section 6.7
can be subverted when the user space application calls connect()
before sendmsg().
Fix it by initializing properly flowi6_oif in connect() before
performing the route lookup.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e4c ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.
This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.
ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With some combinations of user provided flags in netlink command,
it is possible to call tcp_get_info() with a buffer that is not 8-bytes
aligned.
It does matter on some arches, so we need to use put_unaligned() to
store the u64 fields.
Current iproute2 package does not trigger this particular issue.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info") Fixes: 977cb0ecf82e ("tcp: add pacing_rate information into tcp_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.
However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.
Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.
Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.
Fixes: 03bf0c281234 ("switchdev: introduce switchdev notifier") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Later parts of the stack (including fragmentation) expect that there is
never a socket attached to frag in a frag_list, however this invariant
was not enforced on all defrag paths. This could lead to the
BUG_ON(skb->sk) during ip_do_fragment(), as per the call stack at the
end of this commit message.
While the call could be added to openvswitch to fix this particular
error, the head and tail of the frags list are already orphaned
indirectly inside ip_defrag(), so it seems like the remaining fragments
should all be orphaned in all circumstances.
Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action") Signed-off-by: Joe Stringer <joe@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 'commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing
to events")', we terminate the connection if the subscription
creation fails.
In the same commit, the subscription creation result was based on
the value of the subscription pointer (set in the function) instead
of the return code.
Unfortunately, the same function tipc_subscrp_create() handles
subscription cancel request. For a subscription cancellation request,
the subscription pointer cannot be set. Thus if a subscriber has
several subscriptions and cancels any of them, the connection is
terminated.
In this commit, we terminate the connection based on the return value
of tipc_subscrp_create(). Fixes: commit 7fe8097cef5f ("tipc: fix nullpointer bug when subscribing to events") Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 76e398a62712 ("net: dsa: use switchdev obj for VLAN add/del
ops"), the Marvell 88E6xxx switch has been unable to pass traffic
between ports - any received traffic is discarded by the switch.
Taking a port out of bridge mode and configuring a vlan on it also the
port to start passing traffic.
With the debugfs files re-instated to allow debug of this issue by
comparing the register settings between the working and non-working
case, the reason becomes clear:
Register 7 for the ports is the default vlan tag register, and in the
non-working setup, it has been set to 2, despite vlan 2 not being
configured. This causes the switch to drop all packets coming in to
these ports. The working setup has the default vlan tag register set
to 1, which is the default vlan when none is configured.
Inspection of the code reveals why. The code prior to this commit
was:
- for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
- if (!err && vlan->flags & BRIDGE_VLAN_INFO_PVID)
- err = ds->drv->port_pvid_set(ds, p->port, vid);
but the new code is:
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
+ }
...
+ if (pvid)
+ err = _mv88e6xxx_port_pvid_set(ds, port, vid);
This causes the new code to always set the default vlan to one higher
than the old code.
Fix this.
Fixes: 76e398a62712 ("net: dsa: use switchdev obj for VLAN add/del ops") Cc: <stable@vger.kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends commit b93d6471748d ("sctp: implement the sender side
for SACK-IMMEDIATELY extension") as it didn't white list
SCTP_SACK_IMMEDIATELY on sctp_msghdr_parse(), causing it to be
understood as an invalid flag and returning -EINVAL to the application.
Note that the actual handling of the flag is already there in
sctp_datamsg_from_user().
https://tools.ietf.org/html/rfc7053#section-7
Fixes: b93d6471748d ("sctp: implement the sender side for SACK-IMMEDIATELY extension") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several times already this has been reported as kasan reports caused by
syzkaller and trinity and people always looked at RCU races, but it is
much more simple. :)
In case we bind a pptp socket multiple times, we simply add it to
the callid_sock list but don't remove the old binding. Thus the old
socket stays in the bucket with unused call_id indexes and doesn't get
cleaned up. This causes various forms of kasan reports which were hard
to pinpoint.
Simply don't allow multiple binds and correct error handling in
pptp_bind. Also keep sk_state bits in place in pptp_connect.
Fixes: 00959ade36acad ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)") Cc: Dmitry Kozlov <xeb@mail.ru> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Dmitry Vyukov <dvyukov@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Dave Jones <davej@codemonkey.org.uk> Reported-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem here is the skb we provide to tcp_v4_send_ack() had to
be parked in the backlog of a new TCP fastopen child because this child
was owned by the user at the time an out of window packet arrived.
Before queuing a packet, TCP has to set skb->dev to NULL as the device
could disappear before packet is removed from the queue.
Fix this issue by using the net pointer provided by the socket (being a
timewait or a request socket).
IPv6 is immune to the bug : tcp_v6_send_response() already gets the net
pointer from the socket if provided.
Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path") Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jerry Chu <hkchu@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the commit 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be
correctly controlled.") changed the default xmit checksum setting
for lwt vxlan/geneve ipv6 tunnels, so that now the checksum is not
set into external UDP header.
This commit changes the rx checksum setting for both lwt vxlan/geneve
devices created by openvswitch accordingly, so that lwt over ipv6
tunnel pairs are again able to communicate with default values.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jiri Benc <jbenc@redhat.com> Acked-by: Jesse Gross <jesse@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring checksums on UDP tunnels, the flags are different
for IPv4 vs. IPv6 (and reversed). However, when lightweight tunnels
are enabled the flags used are always the IPv4 versions, which are
ignored in the IPv6 code paths. This uses the correct IPv6 flags, so
checksums can be controlled appropriately.
Fixes: a725e514 ("vxlan: metadata based tunneling for IPv6") Fixes: abe492b4 ("geneve: UDP checksum configuration via netlink") Signed-off-by: Jesse Gross <jesse@kernel.org> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY status frames are not reliable, the PHY may not be able to send them
during heavy receive traffic. This overflow condition is signaled by the
PHY in the next status frame, but the driver did not make use of it.
Instead it always reported wrong tx timestamps to user space after an
overflow happened because it assigned newly received tx timestamps to old
packets in the queue.
This commit fixes this issue by clearing the tx timestamp queue every time
an overflow happens, so that no timestamps are delivered for overflow
packets. This way time stamping will continue correctly after an overflow.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GRO is currently not aware of tunnel metadata generated by lightweight
tunnels and stored in the dst. This leads to two possible problems:
* Incorrectly merging two frames that have different metadata.
* Leaking of allocated metadata from merged frames.
This avoids those problems by comparing the tunnel information before
merging, similar to how we handle other metadata (such as vlan tags),
and releasing any state when we are done.
Reported-by: John <john.phillips5@hpe.com> Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.") Signed-off-by: Jesse Gross <jesse@kernel.org> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support the generic kernel parameter parse_args() was
extended via commit ecc8617053e0 ("module: add extra
argument for parse_params() callback") however commit
failed to f2411da746985 failed to add the required argument.
This causes a crash then whenever async_probe generic
module parameter is used. This was overlooked when the
form in which in-kernel async probe support was reworked
a bit... Fix this as originally intended.
Cc: Hannes Reinecke <hare@suse.de> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> [minimized] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Helge reported for timerfd we have the same issue in itimers. We return
remaining time larger than the programmed relative time to user space in case
of CONFIG_TIME_LOW_RES=y. Use the proper function to adjust the extra time
added in hrtimer_start_range_ns().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Helge Deller <deller@gmx.de> Cc: John Stultz <john.stultz@linaro.org> Cc: linux-m68k@lists.linux-m68k.org Cc: dhowells@redhat.com Link: http://lkml.kernel.org/r/20160114164159.528222587@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Helge reported for timerfd we have the same issue in posix timers. We
return remaining time larger than the programmed relative time to user space
in case of CONFIG_TIME_LOW_RES=y. Use the proper function to adjust the extra
time added in hrtimer_start_range_ns().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Helge Deller <deller@gmx.de> Cc: John Stultz <john.stultz@linaro.org> Cc: linux-m68k@lists.linux-m68k.org Cc: dhowells@redhat.com Link: http://lkml.kernel.org/r/20160114164159.450510905@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge reported that a relative timer can return a remaining time larger than
the programmed relative time on parisc and other architectures which have
CONFIG_TIME_LOW_RES set. This happens because we add a jiffie to the resulting
expiry time to prevent short timeouts.
Use the new function hrtimer_expires_remaining_adjusted() to calculate the
remaining time. It takes that extra added time into account for relative
timers.
Reported-and-tested-by: Helge Deller <deller@gmx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org> Cc: linux-m68k@lists.linux-m68k.org Cc: dhowells@redhat.com Link: http://lkml.kernel.org/r/20160114164159.354500742@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An unprivileged user can trigger an oops on a kernel with
CONFIG_CHECKPOINT_RESTORE.
proc_pid_cmdline_read takes mmap_sem for reading and obtains args + env
start/end values. These get sanity checked as follows:
BUG_ON(arg_start > arg_end);
BUG_ON(env_start > env_end);
These can be changed by prctl_set_mm. Turns out also takes the semaphore for
reading, effectively rendering it useless. This results in:
Turns out there are instances where the code just reads aformentioned
values without locking whatsoever - namely environ_read and get_cmdline.
Interestingly these functions look quite resilient against bogus values,
but I don't believe this should be relied upon.
The first patch gets rid of the oops bug by grabbing mmap_sem for
writing.
The second patch is optional and puts locking around aformentioned
consumers for safety. Consumers of other fields don't seem to benefit
from similar treatment and are left untouched.
This patch (of 2):
The code was taking the semaphore for reading, which does not protect
against readers nor concurrent modifications.
The problem could cause a sanity checks to fail in procfs's cmdline
reader, resulting in an OOPS.
Note that some functions perform an unlocked read of various mm fields,
but they seem to be fine despite possible modificaton.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Jarod Wilson <jarod@redhat.com> Cc: Jan Stancek <jstancek@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Anshuman Khandual <anshuman.linux@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently I've been seeing xfs/051 fail on 1k block size filesystems.
Trying to trace the events during the test lead to the problem going
away, indicating that it was a race condition that lead to this
ASSERT failure:
When I finally caught it with tracing enabled, I saw that AG 2 had
an elevated reference count and a buffer was responsible for it. I
tracked down the specific buffer, and found that it was missing the
final reference count release that would put it back on the LRU and
hence be found by xfs_wait_buftarg() calls in the log mount failure
handling.
The last four traces for the buffer before the assert were (trimmed
for relevance)
kworker/0:1-5259 xfs_buf_iodone: hold 2 lock 0 flags ASYNC
kworker/0:1-5259 xfs_buf_ioerror: hold 2 lock 0 error -5
mount-7163 xfs_buf_lock_done: hold 2 lock 0 flags ASYNC
mount-7163 xfs_buf_unlock: hold 2 lock 1 flags ASYNC
This is an async write that is completing, so there's nobody waiting
for it directly. Hence we call xfs_buf_relse() once all the
processing is complete. That does:
Now, it's clear that mount is waiting on the buffer lock, and that
it has been released by xfs_buf_relse() and gained by mount. This is
expected, because at this point the mount process is in
xfs_buf_delwri_submit() waiting for all the IO it submitted to
complete.
The mount process, however, is waiting on the lock for the buffer
because it is in xfs_buf_delwri_submit(). This waits for IO
completion, but it doesn't wait for the buffer reference owned by
the IO to go away. The mount process collects all the completions,
fails the log recovery, and the higher level code then calls
xfs_wait_buftarg() to free all the remaining buffers in the
filesystem.
The issue is that on unlocking the buffer, the scheduler has decided
that the mount process has higher priority than the the kworker
thread that is running the IO completion, and so immediately
switched contexts to the mount process from the semaphore unlock
code, hence preventing the kworker thread from finishing the IO
completion and releasing the IO reference to the buffer.
Hence by the time that xfs_wait_buftarg() is run, the buffer still
has an active reference and so isn't on the LRU list that the
function walks to free the remaining buffers. Hence we miss that
buffer and continue onwards to tear down the mount structures,
at which time we get find a stray reference count on the perag
structure. On a non-debug kernel, this will be ignored and the
structure torn down and freed. Hence when the kworker thread is then
rescheduled and the buffer released and freed, it will access a
freed perag structure.
The problem here is that when the log mount fails, we still need to
quiesce the log to ensure that the IO workqueues have returned to
idle before we run xfs_wait_buftarg(). By synchronising the
workqueues, we ensure that all IO completions are fully processed,
not just to the point where buffers have been unlocked. This ensures
we don't end up in the situation above.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 24ba16bb3d499c49974669cd8429c3e4138ab102 as it
prevents machines from suspending. This regression occurs when the
xfsaild is idle on entry to suspend, and so there s no activity to
wake it from it's idle sleep and hence see that it is supposed to
freeze. Hence the freezer times out waiting for it and suspend is
cancelled.
There is no obvious fix for this short of freezing the filesystem
properly, so revert this change for now.
Signed-off-by: Dave Chinner <david@fromorbit.com> Acked-by: Jiri Kosina <jkosina@suse.cz> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we do inode readahead in log recovery, we do can do the
readahead before we've replayed the icreate transaction that stamps
the buffer with inode cores. The inode readahead verifier catches
this and marks the buffer as !done to indicate that it doesn't yet
contain valid inodes.
In adding buffer error notification (i.e. setting b_error = -EIO at
the same time as as we clear the done flag) to such a readahead
verifier failure, we can then get subsequent inode recovery failing
with this error:
This occurs when readahead completion races with icreate item replay
such as:
inode readahead
find buffer
lock buffer
submit RA io
....
icreate recovery
xfs_trans_get_buffer
find buffer
lock buffer
<blocks on RA completion>
.....
<ra completion>
fails verifier
clear XBF_DONE
set bp->b_error = -EIO
release and unlock buffer
<icreate gains lock>
icreate initialises buffer
marks buffer as done
adds buffer to delayed write queue
releases buffer
At this point, we have an initialised inode buffer that is up to
date but has an -EIO state registered against it. When we finally
get to recovering an inode in that buffer:
inode item recovery
xfs_trans_read_buffer
find buffer
lock buffer
sees XBF_DONE is set, returns buffer
sees bp->b_error is set
fail log recovery!
Essentially, we need xfs_trans_get_buf_map() to clear the error status of
the buffer when doing a lookup. This function returns uninitialised
buffers, so the buffer returned can not be in an error state and
none of the code that uses this function expects b_error to be set
on return. Indeed, there is an ASSERT(!bp->b_error); in the
transaction case in xfs_trans_get_buf_map() that would have caught
this if log recovery used transactions....
This patch firstly changes the inode readahead failure to set -EIO
on the buffer, and secondly changes xfs_buf_get_map() to never
return a buffer with an error state set so this first change doesn't
cause unexpected log recovery failures.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because struct xfs_agfl is 36 bytes long and has a 64-bit integer
inside it, gcc will quietly round the structure size up to the nearest
64 bits -- in this case, 40 bytes. This results in the XFS_AGFL_SIZE
macro returning incorrect results for v5 filesystems on 64-bit
machines (118 items instead of 119). As a result, a 32-bit xfs_repair
will see garbage in AGFL item 119 and complain.
Therefore, tell gcc not to pad the structure so that the AGFL size
calculation is correct.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log