Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Turn the error paramter into a pointer so that target drivers can change
the value, and make sure only DM_ENDIO_* values are returned from the
methods.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Instead use the special DM_MAPIO_KILL return value to return -EIO just
like we do for the request based path. Note that dm-log-writes returned
-ENOMEM in a few places, which now becomes -EIO instead. No consumer
treats -ENOMEM special so this shouldn't be an issue (and it should
use a mempool to start with to make guaranteed progress).
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
block_dev: propagate bio_iov_iter_get_pages error in __blkdev_direct_IO
Once we move the block layer to its own status code we'll still want to
propagate the bio_iov_iter_get_pages, so restructure __blkdev_direct_IO
to take ret into account when returning the errno.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
A few (but not all) dm targets use a special EWOULDBLOCK error code for
failing REQ_RAHEAD requests that fail due to a lack of available resources.
But no one else knows about this magic code, and lower level drivers also
don't generate it when failing read-ahead requests for similar reasons.
So remove this special casing and ignore all additional error handling for
REQ_RAHEAD - if this was a real underlying error we'd get a normal read
once the real read comes in.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Josef Bacik [Thu, 8 Jun 2017 19:39:30 +0000 (15:39 -0400)]
nbd: set sk->sk_sndtimeo for our sockets
If the nbd server stops receiving packets altogether we will get stuck
waiting for them to receive indefinitely as the tcp buffer will never
empty, which looks like a deadlock. Fix this by setting the sk send
timeout to our configured timeout, that way if the server really
misbehaves we'll disconnect cleanly instead of waiting forever.
Reported-by: Dan Melnic <dmm@fb.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Arnd Bergmann [Fri, 9 Jun 2017 10:19:18 +0000 (12:19 +0200)]
loop: fix error handling regression
gcc points out an unusual indentation:
drivers/block/loop.c: In function 'loop_set_status':
drivers/block/loop.c:1149:3: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
if (figure_loop_size(lo, info->lo_offset, info->lo_sizelimit,
^~
drivers/block/loop.c:1152:4: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
goto exit;
This was introduced by a new feature that accidentally moved the opening
braces from one condition to another. Adding a second pair of braces
makes it work correctly again and also more readable.
Hannes Reinecke [Thu, 8 Jun 2017 11:46:45 +0000 (13:46 +0200)]
loop: support 4k physical blocksize
When generating bootable VM images certain systems (most notably
s390x) require devices with 4k blocksize. This patch implements
a new flag 'LO_FLAGS_BLOCKSIZE' which will set the physical
blocksize to that of the underlying device, and allow to change
the logical blocksize for up to the physical blocksize.
Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Wed, 31 May 2017 21:43:50 +0000 (14:43 -0700)]
nfsd: Check queue type before submitting a SCSI request
Since using scsi_req() is only allowed against request queues for
which struct scsi_request is the first member of their private
request data, refuse to submit SCSI commands against a queue for
which this is not the case.
References: commit 82ed4db499b8 ("block: split scsi_request out of struct request") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: J. Bruce Fields <bfields@redhat.com> Cc: Jeff Layton <jlayton@poochiereds.net> Cc: Omar Sandoval <osandov@fb.com> Cc: linux-nfs@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Wed, 31 May 2017 21:43:49 +0000 (14:43 -0700)]
cdrom: Check SCSI passthrough support before reading audio
The CDROMREADAUDIO ioctl uses SCSI passthrough when the .disk
pointer has been set in struct cdrom_device_info. Hence check
whether SCSI passthrough is supported before submitting a SCSI
command. Note: both the ide-cd and sr drivers set the disk
pointer in struct cdrom_device_info but neither the pcd nor
the gdrom driver sets that pointer.
References: commit 82ed4db499b8 ("block: split scsi_request out of struct request") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Omar Sandoval <osandov@fb.com> Cc: linux-block@vger.kernel.org Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Wed, 31 May 2017 21:43:48 +0000 (14:43 -0700)]
pktcdvd: Check queue type before attaching to a queue
Since the pktcdvd driver only supports request queues for which
struct scsi_request is the first member of their private request
data, refuse to register block layer queues for which struct
scsi_request is not the first member of the private data.
References: commit 82ed4db499b8 ("block: split scsi_request out of struct request") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Wed, 31 May 2017 21:43:47 +0000 (14:43 -0700)]
bsg: Check queue type before attaching to a queue
Since BSG only supports request queues for which struct scsi_request
is the first member of their private request data, refuse to register
block layer queues for which struct scsi_request is not the first
member of their private data.
References: commit bd1599d931ca ("scsi_transport_sas: fix BSG ioctl memory corruption")
References: commit 82ed4db499b8 ("block: split scsi_request out of struct request") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Wed, 31 May 2017 21:43:46 +0000 (14:43 -0700)]
block: Introduce queue flag QUEUE_FLAG_SCSI_PASSTHROUGH
From the context where a SCSI command is submitted it is not always
possible to figure out whether or not the queue the command is
submitted to has struct scsi_request as the first member of its
private data. Hence introduce the flag QUEUE_FLAG_SCSI_PASSTHROUGH.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Omar Sandoval <osandov@fb.com> Cc: Don Brace <don.brace@microsemi.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Thu, 1 Jun 2017 15:55:13 +0000 (08:55 -0700)]
blk-mq-debugfs: Add 'kick' operation
Running a queue causes the block layer to examine the per-CPU and
hw queues but not the requeue list. Hence add a 'kick' operation
that also examines the requeue list.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Eduardo Valentin <eduval@amazon.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Thu, 1 Jun 2017 15:55:12 +0000 (08:55 -0700)]
blk-mq-debugfs: Show busy requests
Requests that got stuck in a block driver are neither on
blk_mq_ctx.rq_list nor on any hw dispatch queue. Make these
visible in debugfs through the "busy" attribute.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Eduardo Valentin <eduval@amazon.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Omar Sandoval <osandov@fb.com> Cc: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Bart Van Assche [Thu, 1 Jun 2017 15:55:11 +0000 (08:55 -0700)]
blk-mq-debugfs: Show requeue list
When verifying whether or not a blk-mq driver forgot to kick the
requeue list after having requeued a request it is important to
be able to verify the contents of the requeue list. Hence export
that list through debugfs.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Eduardo Valentin <eduval@amazon.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Omar Sandoval <osandov@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Shaun McDowell [Fri, 26 May 2017 03:55:54 +0000 (23:55 -0400)]
nbd: add FUA op support
NBD userland client and server have FUA (forced unit access) support
and flags defined. Make NBD kernel module recognize NBD_FLAG_SEND_FUA,
enable FUA on the queue, and forward FUA requests to the server.
Ming Lei [Fri, 26 May 2017 11:53:20 +0000 (19:53 +0800)]
blk-mq: make per-sw-queue bio merge as default .bio_merge
Because what the per-sw-queue bio merge does is basically same with
scheduler's .bio_merge(), this patch makes per-sw-queue bio merge
as the default .bio_merge if no scheduler is used or io scheduler
doesn't provide .bio_merge().
Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Fri, 26 May 2017 11:53:19 +0000 (19:53 +0800)]
blk-mq: merge bio into sw queue before plugging
Before blk-mq is introduced, I/O is merged to elevator
before being putted into plug queue, but blk-mq changed the
order and makes merging to sw queue basically impossible.
Then it is observed that throughput of sequential I/O is degraded
about 10%~20% on virtio-blk in the test[1] if mq-deadline isn't used.
This patch moves the bio merging per sw queue before plugging,
like what blk_queue_bio() does, and the performance regression is
fixed under this situation.
- Fix warnings about unused variables that appeared in -rc1.
- Don't spew errors when bmapping a local format directory
- Fix an off-by-one error in a delalloc eof assertion
- Make fsmap only return inode information for CAP_SYS_ADMIN
- Fix a potential mount time deadlock recovering cow extents
- Fix unaligned memory access in _btree_visit_blocks
- Fix various SEEK_HOLE/SEEK_DATA bugs"
* tag 'xfs-4.12-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
xfs: Fix missed holes in SEEK_HOLE implementation
xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
xfs: fix unaligned access in xfs_btree_visit_blocks
xfs: avoid mount-time deadlock in CoW extent recovery
xfs: only return detailed fsmap info if the caller has CAP_SYS_ADMIN
xfs: bad assertion for delalloc an extent that start at i_size
xfs: fix warnings about unused stack variables
xfs: BMAPX shouldn't barf on inline-format directories
xfs: fix indlen accounting error on partial delalloc conversion
Linus Torvalds [Fri, 26 May 2017 18:05:22 +0000 (11:05 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into this series. This contains:
- A set of NVMe fixes, pulled from Christoph. This includes a set of
fixes for the fiber channel bits from James Smart, rdma queue depth
fix from Marta, controller removal fixes from Ming, and some more
APST quirk updates from Andy.
- A blk-mq debugfs fix from Bart, fixing a problem with the
untangling of the sysfs and debugfs blk-mq bits that was added in
this series.
- Error code fix in add_partition() from Dan.
- A small series of fixes for the new blk-throttle code from Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block: (21 commits)
blk-mq: Only register debugfs attributes for blk-mq queues
nvme: Quirk APST on Intel 600P/P3100 devices
nvme: only setup block integrity if supported by the driver
nvme: replace is_flags field in nvme_ctrl_ops with a flags field
nvme-pci: consistencly use ctrl->device for logging
partitions/msdos: FreeBSD UFS2 file systems are not recognized
block: fix an error code in add_partition()
blk-throttle: force user to configure all settings for io.low
blk-throttle: respect 0 bps/iops settings for io.low
blk-throttle: output some debug info in trace
blk-throttle: add hierarchy support for latency target and idle time
nvme_fc: remove extra controller reference taken on reconnect
nvme_fc: correct nvme status set on abort
nvme_fc: set logging level on resets/deletes
nvme_fc: revise comment on teardown
nvme_fc: Support ctrl_loss_tmo
nvme_fc: get rid of local reconnect_delay
blk-mq: remove blk_mq_abort_requeue_list()
nvme: avoid to use blk_mq_abort_requeue_list()
nvme: use blk_mq_start_hw_queues() in nvme_kill_queues()
...
Linus Torvalds [Fri, 26 May 2017 17:51:18 +0000 (10:51 -0700)]
Merge tag 'pci-v4.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix PCI_ENDPOINT build error (merged for v4.12)
- fix Switchtec driver (merged for v4.12)
- fix imx6 config read timeouts, fallout from changing to non-postable
reads
- add PM "needs_resume" flag for i915 suspend issue
* tag 'pci-v4.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
Linus Torvalds [Fri, 26 May 2017 16:35:22 +0000 (09:35 -0700)]
Merge tag 'ceph-for-4.12-rc3' of git://github.com/ceph/ceph-client
Pul ceph fixes from Ilya Dryomov:
"A bunch of make W=1 and static checker fixups, a RECONNECT_SEQ
messenger patch from Zheng and Luis' fallocate fix"
* tag 'ceph-for-4.12-rc3' of git://github.com/ceph/ceph-client:
ceph: check that the new inode size is within limits in ceph_fallocate()
libceph: cleanup old messages according to reconnect seq
libceph: NULL deref on crush_decode() error path
libceph: fix error handling in process_one_ticket()
libceph: validate blob_struct_v in process_one_ticket()
libceph: drop version variable from ceph_monmap_decode()
libceph: make ceph_msg_data_advance() return void
libceph: use kbasename() and kill ceph_file_part()
Linus Torvalds [Fri, 26 May 2017 16:05:35 +0000 (09:05 -0700)]
Merge tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
board.
Together with a couple of DTS updates for the Hikey board we have also
extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence
for the WiFi chip"
* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
arm64: dts: hikey: Fix WiFi support
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
arm64: dts: hikey: Add clock for the pmic mfd
mfd: dts: hi655x: Add clock binding for the pmic
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
mmc: dt: pwrseq-simple: Invent power-off-delay-us
Linus Torvalds [Fri, 26 May 2017 16:03:09 +0000 (09:03 -0700)]
Merge tag 'sound-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few HD-audio device-specific quirks and an endianess
fix for USB-audio, as well as the update of quirk model list document.
All fixes are small and trivial.
The document update could have been postponed, but it's a good thing
for user and has absolutely zero risk of breakage, so included here"
* tag 'sound-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - apply STAC_9200_DELL_M22 quirk for Dell Latitude D430
ALSA: hda - Update the list of quirk models
ALSA: hda - Provide dual-codecs model option for a few Realtek codecs
ALSA: hda - Apply dual-codec quirk for MSI Z270-Gaming mobo
ALSA: hda - No loopback on ALC299 codec
ALSA: usb-audio: fix Amanero Combo384 quirk on big-endian hosts
Linus Torvalds [Fri, 26 May 2017 15:54:06 +0000 (08:54 -0700)]
Merge tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Not a whole lot happening here, a set of amdgpu fixes and one core
deadlock fix, and some misc drivers fixes"
* tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: fix null point error when rmmod amdgpu.
drm/amd/powerplay: fix a signedness bugs
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
drm/radeon: Unbreak HPD handling for r600+
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu: fix fundamental suspend/resume issue
drm/gma500/psb: Actually use VBT mode when it is found
drm: Fix deadlock retry loop in page_flip_ioctl
drm: qxl: Delay entering atomic context during cursor update
drm/radeon: Fix oops upon driver load on PowerXpress laptops
Jens Axboe [Fri, 26 May 2017 15:11:19 +0000 (09:11 -0600)]
Merge branch 'nvme-4.12' of git://git.infradead.org/nvme into for-linus
Christoph writes:
"A couple of fixes for the next rc on the nvme front. Various FC fixes
from James, controller removal fixes from Ming (including a block layer
patch), a APST related device quirk from Andy, a RDMA fix for small
queue depth device from Marta, as well as fixes for the lack of
metadata support in non-PCIe drivers and the printk logging format from
me."
Bart Van Assche [Thu, 25 May 2017 23:38:06 +0000 (16:38 -0700)]
blk-mq: Only register debugfs attributes for blk-mq queues
The code in blk-mq-debugfs.c assumes that it is working on a blk-mq
queue and is not intended to work on a blk-sq queue. Hence only
register blk-mq debugfs attributes for blk-mq queues.
Fixes: commit 9c1051aacde8 ("blk-mq: untangle debugfs and sysfs") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Andy Lutomirski [Wed, 24 May 2017 22:06:31 +0000 (15:06 -0700)]
nvme: Quirk APST on Intel 600P/P3100 devices
They have known firmware bugs. A fix is apparently in the works --
once fixed firmware is available, someone from Intel (Hi, Keith!)
can adjust the quirk accordingly.
Cc: stable@vger.kernel.org # v4.11 Cc: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: Mario Limonciello <mario_limonciello@dell.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme: only setup block integrity if supported by the driver
Currently only the PCIe driver supports metadata, so we should not claim
integrity support for the other drivers. This prevents nasty crashes
with targets that advertise metadata support on fabrics.
Also use the opportunity to factor out some code into a separate helper
that isn't even compiled if CONFIG_BLK_DEV_INTEGRITY is disabled.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <keith.busch@intel.com>
Dave Airlie [Fri, 26 May 2017 01:51:55 +0000 (11:51 +1000)]
Merge branch 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A bunch of bug fixes:
- Fix display flickering on some chips at high refresh rates
- suspend/resume fix
- hotplug fix
- a couple of segfault fixes for certain cases
* 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix null point error when rmmod amdgpu.
drm/amd/powerplay: fix a signedness bugs
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
drm/radeon: Unbreak HPD handling for r600+
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu: fix fundamental suspend/resume issue
Dave Airlie [Fri, 26 May 2017 01:51:28 +0000 (11:51 +1000)]
Merge tag 'drm-misc-fixes-2017-05-25' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Core Changes:
- Don't drop vblank reference more than once in cases of ww retry (Daniel)
Driver Changes:
- radeon: Fix oops during radeon probe trying to reference wrong device (Lukas)
- qxl: Avoid sleeping while in atomic context on cursor update (Gabriel)
- gma500: Use VBT mode instead of pre-programmed mode for LVDS (Patrik)
Cc: Lukas Wunner <lukas@wunner.de> Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
* tag 'drm-misc-fixes-2017-05-25' of git://anongit.freedesktop.org/git/drm-misc:
drm/gma500/psb: Actually use VBT mode when it is found
drm: Fix deadlock retry loop in page_flip_ioctl
drm: qxl: Delay entering atomic context during cursor update
drm/radeon: Fix oops upon driver load on PowerXpress laptops
Jan Kara [Thu, 18 May 2017 23:36:24 +0000 (16:36 -0700)]
xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
Currently several places in xfs_find_get_desired_pgoff() handle the case
of a missing page. Make them all handled in one place after the loop has
terminated.
Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Jan Kara [Thu, 18 May 2017 23:36:23 +0000 (16:36 -0700)]
xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
There is an off-by-one error in loop termination conditions in
xfs_find_get_desired_pgoff() since 'end' may index a page beyond end of
desired range if 'endoff' is page aligned. It doesn't have any visible
effects but still it is good to fix it.
Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Jan Kara [Thu, 18 May 2017 23:36:22 +0000 (16:36 -0700)]
xfs: Fix missed holes in SEEK_HOLE implementation
XFS SEEK_HOLE implementation could miss a hole in an unwritten extent as
can be seen by the following command:
xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k"
-c "seek -h 0" file
wrote 57344/57344 bytes at offset 0
56 KiB, 14 ops; 0.0000 sec (49.312 MiB/sec and 12623.9856 ops/sec)
wrote 8192/8192 bytes at offset 131072
8 KiB, 2 ops; 0.0000 sec (70.383 MiB/sec and 18018.0180 ops/sec)
Whence Result
HOLE 139264
Where we can see that hole at offset 56k was just ignored by SEEK_HOLE
implementation. The bug is in xfs_find_get_desired_pgoff() which does
not properly detect the case when pages are not contiguous.
Fix the problem by properly detecting when found page has larger offset
than expected.
CC: stable@vger.kernel.org Fixes: d126d43f631f996daeee5006714fed914be32368 Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Eryu Guan [Tue, 23 May 2017 15:30:46 +0000 (08:30 -0700)]
xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
xfs_find_get_desired_pgoff() is used to search for offset of hole or
data in page range [index, end] (both inclusive), and the max number
of pages to search should be at least one, if end == index.
Otherwise the only page is missed and no hole or data is found,
which is not correct.
When block size is smaller than page size, this can be demonstrated
by preallocating a file with size smaller than page size and writing
data to the last block. E.g. run this xfs_io command on a 1k block
size XFS on x86_64 host.
# xfs_io -fc "falloc 0 3k" -c "pwrite 2k 1k" \
-c "seek -d 0" /mnt/xfs/testfile
wrote 1024/1024 bytes at offset 2048
1 KiB, 1 ops; 0.0000 sec (33.675 MiB/sec and 34482.7586 ops/sec)
Whence Result
DATA EOF
Data at offset 2k was missed, and lseek(2) returned ENXIO.
This is uncovered by generic/285 subtest 07 and 08 on ppc64 host,
where pagesize is 64k. Because a recent change to generic/285
reduced the preallocated file size to smaller than 64k.
Cc: stable@vger.kernel.org # v3.7+ Signed-off-by: Eryu Guan <eguan@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Eric Sandeen [Tue, 23 May 2017 02:54:10 +0000 (19:54 -0700)]
xfs: fix unaligned access in xfs_btree_visit_blocks
This structure copy was throwing unaligned access warnings on sparc64:
Kernel unaligned access at TPC[1043c088] xfs_btree_visit_blocks+0x88/0xe0 [xfs]
xfs_btree_copy_ptrs does a memcpy, which avoids it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds [Thu, 25 May 2017 03:29:53 +0000 (20:29 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a big update because it includes a rework of the lpfc
driver to separate the NVMe part from the FC part.
The reason for doing this is because two separate trees (the nvme and
scsi trees respectively) want to update the individual components and
this separation will prevent a really nasty cross tree entanglement by
the time we reach the next merge window.
The rest of the fixes are the usual minor sort with no significant
security implications"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (25 commits)
scsi: zero per-cmd private driver data for each MQ I/O
scsi: csiostor: fix use after free in csio_hw_use_fwconfig()
scsi: ufs: Clean up some rpm/spm level SysFS nodes upon remove
scsi: lpfc: fix build issue if NVME_FC_TARGET is not defined
scsi: lpfc: Fix NULL pointer dereference during PCI error recovery
scsi: lpfc: update version to 11.2.0.14
scsi: lpfc: Add MDS Diagnostic support.
scsi: lpfc: Fix NVMEI's handling of NVMET's PRLI response attributes
scsi: lpfc: Cleanup entry_repost settings on SLI4 queues
scsi: lpfc: Fix debugfs root inode "lpfc" not getting deleted on driver unload.
scsi: lpfc: Fix NVME I+T not registering NVME as a supported FC4 type
scsi: lpfc: Added recovery logic for running out of NVMET IO context resources
scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context
scsi: lpfc: Separate NVMET data buffer pool fir ELS/CT.
scsi: lpfc: Fix NMI watchdog assertions when running nvmet IOPS tests
scsi: lpfc: Fix NVMEI driver not decrementing counter causing bad rport state.
scsi: lpfc: Fix nvmet RQ resource needs for large block writes.
scsi: lpfc: Adding additional stats counters for nvme.
scsi: lpfc: Fix system crash when port is reset.
scsi: lpfc: Fix used-RPI accounting problem.
...
Fixes: 7b52db39a4c2 ("drm/amd/powerplay: fix bug sclk/mclk
level can't be set on vega10.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Eric Huang <JinHuiEric.Huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude [Thu, 11 May 2017 23:31:12 +0000 (19:31 -0400)]
drm/radeon: Unbreak HPD handling for r600+
We end up reading the interrupt register for HPD5, and then writing it
to HPD6 which on systems without anything using HPD5 results in
permanently disabling hotplug on one of the display outputs after the
first time we acknowledge a hotplug interrupt from the GPU.
This code is really bad. But for now, let's just fix this. I will
hopefully have a large patch series to refactor all of this soon.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Lyude <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Wed, 10 May 2017 18:06:58 +0000 (20:06 +0200)]
drm/amdgpu: fix fundamental suspend/resume issue
Reinitializing the VM manager during suspend/resume is a very very bad
idea since all the VMs are still active and kicking.
This can lead to random VM faults after resume when new processes
become the same client ID assigned.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Luis Henriques [Fri, 5 May 2017 17:28:44 +0000 (18:28 +0100)]
ceph: check that the new inode size is within limits in ceph_fallocate()
Currently the ceph client doesn't respect the rlimit in fallocate. This
means that a user can allocate a file with size > RLIMIT_FSIZE. This
patch adds the call to inode_newsize_ok() to verify filesystem limits and
ulimits. This should make ceph successfully run xfstest generic/228.
Linus Torvalds [Wed, 24 May 2017 15:28:59 +0000 (08:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ptrace fix from Eric Biederman:
"This fixes a brown paper bag bug. When I fixed the ptrace interaction
with user namespaces I added a new field ptracer_cred in struct_task
and I failed to properly initialize it on fork.
This dangling pointer wound up breaking runing setuid applications run
from the enlightenment window manager.
As this is the worst sort of bug. A regression breaking user space for
no good reason let's get this fixed"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: Properly initialize ptracer_cred on fork
Linus Torvalds [Wed, 24 May 2017 15:21:56 +0000 (08:21 -0700)]
Merge tag 'mmc-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes intended for v4.12 rc3:
- sdhci-xenon: Don't free data for phy allocated by devm*
- sdhci-iproc: Suppress spurious interrupts
- cavium: Fix probing race with regulator
- cavium: Prevent crash with incomplete DT
- cavium-octeon: Use proper GPIO name for power control
- cavium-octeon: Fix interrupt enable code"
* tag 'mmc-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-iproc: suppress spurious interrupt with Multiblock read
mmc: cavium: Fix probing race with regulator
of/platform: Make of_platform_device_destroy globally visible
mmc: cavium: Prevent crash with incomplete DT
mmc: cavium-octeon: Use proper GPIO name for power control
mmc: cavium-octeon: Fix interrupt enable code
mmc: sdhci-xenon: kill xenon_clean_phy()
drm/gma500/psb: Actually use VBT mode when it is found
With LVDS we were incorrectly picking the pre-programmed mode instead of
the prefered mode provided by VBT. Make sure we pick the VBT mode if
one is provided. It is likely that the mode read-out code is still wrong
but this patch fixes the immediate problem on most machines.
Imre Deak [Tue, 23 May 2017 19:18:17 +0000 (14:18 -0500)]
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
Some drivers - like i915 - may not support the system suspend direct
complete optimization due to differences in their runtime and system
suspend sequence. Add a flag that when set resumes the device before
calling the driver's system suspend handlers which effectively disables
the optimization.
Needed by a future patch fixing suspend/resume on i915.
Suggested by Rafael.
Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: stable@vger.kernel.org
Dan Carpenter [Tue, 23 May 2017 14:25:10 +0000 (17:25 +0300)]
libceph: NULL deref on crush_decode() error path
If there is not enough space then ceph_decode_32_safe() does a goto bad.
We need to return an error code in that situation. The current code
returns ERR_PTR(0) which is NULL. The callers are not expecting that
and it results in a NULL dereference.
Ilya Dryomov [Fri, 19 May 2017 10:21:56 +0000 (12:21 +0200)]
libceph: validate blob_struct_v in process_one_ticket()
None of these are validated in userspace, but since we do validate
reply_struct_v in ceph_x_proc_ticket_reply(), tkt_struct_v (first) and
CephXServiceTicket struct_v (second) in process_one_ticket(), validate
CephXTicketBlob struct_v as well.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org>
Linus Torvalds [Tue, 23 May 2017 16:57:39 +0000 (09:57 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Fix the i2c-designware regression of rc2.
Also, a DMA buffer fix for the tiny-usb driver where the USB core now
loudly complains about the non DMA-capable buffer"
[ I had cherry-picked the designware fix separately because it hit my
laptop, but here is the proper sync with the i2c tree - Linus ]
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Fix bogus sda_hold_time due to uninitialized vars
i2c: i2c-tiny-usb: fix buffer not being DMA capable
Richard [Sun, 21 May 2017 19:27:00 +0000 (12:27 -0700)]
partitions/msdos: FreeBSD UFS2 file systems are not recognized
The code in block/partitions/msdos.c recognizes FreeBSD, OpenBSD
and NetBSD partitions and does a reasonable job picking out OpenBSD
and NetBSD UFS subpartitions.
But for FreeBSD the subpartitions are always "bad".
Kernel: <bsd:bad subpartition - ignored
Though all 3 of these BSD systems use UFS as a file system, only
FreeBSD uses relative start addresses in the subpartition
declarations.
The following patch fixes this for FreeBSD partitions and leaves
the code for OpenBSD and NetBSD intact:
Signed-off-by: Richard Narron <comet.berkeley@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
When I introduced ptracer_cred I failed to consider the weirdness of
fork where the task_struct copies the old value by default. This
winds up leaving ptracer_cred set even when a process forks and
the child process does not wind up being ptraced.
Because ptracer_cred is not set on non-ptraced processes whose
parents were ptraced this has broken the ability of the enlightenment
window manager to start setuid children.
Fix this by properly initializing ptracer_cred in ptrace_init_task
This must be done with a little bit of care to preserve the current value
of ptracer_cred when ptrace carries through fork. Re-reading the
ptracer_cred from the ptracing process at this point is inconsistent
with how PT_PTRACE_CAP has been maintained all of these years.
Tested-by: Takashi Iwai <tiwai@suse.de> Fixes: 64b875f7ac8a ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Ulf Hansson [Wed, 3 May 2017 14:11:33 +0000 (16:11 +0200)]
arm64: dts: hikey: Fix WiFi support
The description of the connection between the dwmmc (SDIO) controller and
the Wifi chip, which is attached to the SDIO bus is wrong. Currently the
SDIO card can't be detected and thus the Wifi doesn't work.
Let's fix this by assigning the correct vmmc supply, which is the always on
regulator VDD_3V3 and remove the WLAN enable regulator altogether. Then to
properly deal with the power on/off sequence, add a mmc-pwrseq node to
describe the resources needed to detect the SDIO card.
Except for the WLAN enable GPIO and its corresponding assert/de-assert
delays, the mmc-pwrseq node also contains a handle to a clock provided by
the hi655x pmic. This clock is also needed to be able to turn on the WiFi
chip.
Ulf Hansson [Wed, 3 May 2017 12:18:26 +0000 (14:18 +0200)]
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
Move the board specific descriptions for the dwmmc nodes in the hi6220 SoC
dtsi, into the hikey dts as it's there these belongs.
While changing this, let's take the opportunity to drop the use of the
"ti,non-removable" binding for one of the dwmmc device nodes, as it's not a
valid binding and not used. Drop also the unnecessary use of "num-slots =
<0x1>" for all of the dwmmc nodes, as there is no need to set this since
when default number of slots is one.
Ulf Hansson [Wed, 3 May 2017 10:46:55 +0000 (12:46 +0200)]
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
The regulator is a part of the hikey board, therefore let's move it from
the hi6220 SoC dtsi file into the hikey dts file . Let's also rename the
regulator according to the datasheet (5V_HUB) to better reflect the HW.
Daniel Lezcano [Mon, 24 Apr 2017 20:40:22 +0000 (22:40 +0200)]
arm64: dts: hikey: Add clock for the pmic mfd
The hi655x PMIC provides the regulators but also a clock. The latter is
missing so let's add it. This clock is used by WiFi/Bluetooth chip, but
that connection is done in a separate change on top of this one.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Lee Jones <lee.jones@linaro.org>
[Ulf: Split patch and updated changelog] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de>
Daniel Lezcano [Mon, 24 Apr 2017 20:40:22 +0000 (22:40 +0200)]
mfd: dts: hi655x: Add clock binding for the pmic
The hi655x PMIC provides the regulators but also a clock. The latter is
missing in the definition, so extend the documentation to include this as
well.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Lee Jones <lee.jones@linaro.org>
[Ulf: Split patch and updated changelog] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de>
Ulf Hansson [Sat, 6 May 2017 09:43:05 +0000 (11:43 +0200)]
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
If the optional power-off-delay-us property is found, insert the
corresponding delay after asserting the GPIO during power off. This enables
a graceful shutdown sequence for some devices.
Ulf Hansson [Sat, 6 May 2017 09:41:30 +0000 (11:41 +0200)]
mmc: dt: pwrseq-simple: Invent power-off-delay-us
During power off, after the GPIO pin has been asserted, some devices like
the Wifi chip from TI, Wl18xx, needs a delay before the host continues with
clock gating and turning off regulators as to follow a graceful shutdown
sequence.
Therefore invent an optional power-off-delay-us DT binding for
mmc-pwrseq-simple, to allow us to support this constraint.
Daniel Vetter [Mon, 22 May 2017 13:59:45 +0000 (15:59 +0200)]
drm: Fix deadlock retry loop in page_flip_ioctl
I failed to properly onion-wrap the unwind code: We acquire the vblank
reference before we start with the wait-wound locking dance, hence we
must make sure we retry before we drop the reference. Oops.
v2: The vblank_put must be after the frambuffer_put (Michel). I suck at
unwrapping code that doesn't use separate labels for each stage, but
checks each pointer first ... While re-reading everything I also
realized that we must clean up the fb refcounts, and specifically
plane->old_fb before we drop the locks, either in the final unlocking,
or in the w/w retry path. Hence the correct fix is to drop the
vblank_put to the very bottom.
Fixes: 29dc0d1de182 ("drm: Roll out acquire context for the page_flip ioctl") Cc: Harry Wentland <harry.wentland@amd.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Reported-by: Tommi Rantala <tt.rantala@gmail.com> Cc: Tommi Rantala <tt.rantala@gmail.com> Cc: Michel Dänzer <michel@daenzer.net> Tested-by: Tommi Rantala <tt.rantala@gmail.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170522135945.28831-1-daniel.vetter@ffwll.ch
drm: qxl: Delay entering atomic context during cursor update
qxl_release_map will enter an atomic context, but since we still need to
alloc memory for BOs, we better delay that until we have everything we
need, in case we need to sleep inside the allocation. This avoids the
Sleep in atomic state below, which was reported by Mike.
Linus Torvalds [Tue, 23 May 2017 04:30:20 +0000 (21:30 -0700)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a regression in the skcipher interface that allows bogus
key parameters to hit underlying implementations which can cause
crashes"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - Add missing API setkey checks
Linus Torvalds [Tue, 23 May 2017 02:26:33 +0000 (19:26 -0700)]
Merge tag 'acpi-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert a 4.11 change that turned out to be problematic and add a
.gitignore file.
Specifics:
- Revert a 4.11 commit related to the ACPI-based handling of laptop
lids that made changes incompatible with existing user space stacks
and broke things there (Lv Zheng).
- Add .gitignore to the ACPI tools directory (Prarit Bhargava)"
* tag 'acpi-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / button: Remove lid_init_state=method mode"
tools/power/acpi: Add .gitignore file
Linus Torvalds [Tue, 23 May 2017 02:24:32 +0000 (19:24 -0700)]
Merge tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix RTC wakeup from suspend-to-idle broken recently, fix CPU
idleness detection condition in the schedutil cpufreq governor, fix a
cpufreq driver build failure, fix an error code path in the power
capping framework, clean up the hibernate core and update the
intel_pstate documentation.
Specifics:
- Fix RTC wakeup from suspend-to-idle broken by the recent rework of
ACPI wakeup handling (Rafael Wysocki).
- Update intel_pstate driver documentation to reflect the current
code and explain how it works in more detail (Rafael Wysocki).
- Fix an issue related to CPU idleness detection on systems with
shared cpufreq policies in the schedutil governor (Juri Lelli).
- Fix a possible build issue in the dbx500 cpufreq driver (Arnd
Bergmann).
- Fix a function in the power capping framework core to return an
error code instead of 0 when there's an error (Dan Carpenter).
- Clean up variable definition in the hibernation core (Pushkar
Jambhlekar)"
* tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dbx500: add a Kconfig symbol
PM / hibernate: Declare variables as static
PowerCap: Fix an error code in powercap_register_zone()
RTC: rtc-cmos: Fix wakeup from suspend-to-idle
PM / wakeup: Fix up wakeup_source_report_event()
cpufreq: intel_pstate: Document the current behavior and user interface
cpufreq: schedutil: use now as reference when aggregating shared policy requests
Jan Kiszka [Mon, 22 May 2017 05:46:55 +0000 (07:46 +0200)]
i2c: designware: Fix bogus sda_hold_time due to uninitialized vars
We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de> Fixes: 9d6408433019 ("i2c: designware: don't infer timings described by ACPI from clock rate") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Thu, 18 May 2017 20:07:49 +0000 (13:07 -0700)]
efi-pstore: Fix write/erase id tracking
Prior to the pstore interface refactoring, the "id" generated during
a backend pstore_write() was only retained by the internal pstore
inode tracking list. Additionally the "part" was ignored, so EFI
would encode this in the id. This corrects the misunderstandings
and correctly sets "id" during pstore_write(), and uses "part"
directly during pstore_erase().
Reported-by: Marta Lofstedt <marta.lofstedt@intel.com> Fixes: 76cc9580e3fb ("pstore: Replace arguments for write() API") Fixes: a61072aae693 ("pstore: Replace arguments for erase() API") Signed-off-by: Kees Cook <keescook@chromium.org> Tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Lucas Stach [Mon, 22 May 2017 22:06:30 +0000 (17:06 -0500)]
PCI: imx6: Fix config read timeout handling
Commit cc7b0d495589 ("PCI: designware: Update PCI config space remap
function") made PCI configuration requests non-posted, which means we now
get a synchronous abort when the CFG space read to probe for downstream
devices times out.
Synchronous aborts need to be handled differently from the async aborts we
were getting before, in particular the PC needs to be advanced when
resolving the abort. This is mostly a copy of what other PCI drivers do on
ARM to handle those aborts.
[bhelgaas: changelog, "Fixes"] Fixes: cc7b0d495589 ("PCI: designware: Update PCI config space remap function") Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Logan Gunthorpe [Mon, 22 May 2017 21:52:30 +0000 (16:52 -0500)]
switchtec: Fix minor bug with partition ID register
When a switch endpoint is configured without NTB, the mmio_ntb registers
will read all zeros. However, in corner case configurations where the
partition ID is not zero and NTB is not enabled, the code will have the
wrong partition ID and this causes the driver to use the wrong set of
drivers. To fix this we simply take the partition ID from the system info
region.
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `__pci_epc_create':
(.text+0xef4e): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epc_add_epf':
(.text+0xf676): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epf_alloc_space':
(.text+0xfa32): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epf_free_space':
(.text+0xfac4): undefined reference to `bad_dma_ops'
Shaohua Li [Wed, 17 May 2017 20:07:27 +0000 (13:07 -0700)]
blk-throttle: force user to configure all settings for io.low
Default value of io.low limit is 0. If user doesn't configure the limit,
last patch makes cgroup be throttled to very tiny bps/iops, which could
stall the system. A cgroup with default settings of io.low limit really
means nothing, so we force user to configure all settings, otherwise
io.low limit doesn't take effect. With this stragety, default setting of
latency/idle isn't important, so just set them to very conservative and
safe value.
Shaohua Li [Wed, 17 May 2017 20:07:26 +0000 (13:07 -0700)]
blk-throttle: respect 0 bps/iops settings for io.low
If a cgroup with low limit 0 for both bps/iops, the cgroup's low limit
is ignored and we throttle the cgroup with its max limit. In this way,
other cgroups with a low limit will not get protected. To fix this, we
don't do the exception any more. cgroup will be throttled to a limit 0
if it uese default setting. To avoid completed stall, we give such
cgroup tiny IO resources.
Shaohua Li [Wed, 17 May 2017 20:07:24 +0000 (13:07 -0700)]
blk-throttle: add hierarchy support for latency target and idle time
For idle time, children's setting should not be bigger than parent's.
For latency target, children's setting should not be smaller than
parent's. The leaf nodes will adjust their settings according to the
hierarchy and compare their IO with the settings and do
upgrade/downgrade. parents nodes don't need to track their IO
latency/idle time.
projects / karo-tx-linux.git / log