The generic lro code checks TCP flags/options.
Remove duplicate tests done in the driver.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A SGE queue set timer might access registers while in EEH recovery,
triggering an EEH error loop. Stop all timers early in EEH process.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Karsten Keil <kkeil@novell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
STAC/IDT driver creates "Headphone as Line-Out" switch even if there
is no line-out pins on the machine. For devices only with headpohnes
and speaker-outs, this switch shouldn't be created.
Added a QUIRK to patch_analog.c for the HP Elitebook 8530p
(IDs 0x103c:0x30e7) to use AD1884A model 'laptop' by default.
Playback and Capture confirmed working.
Use model=lenovo-ms7195-dig for MEDION MD96630 laptop (17c0:4085)
with ALC888 codec.
Reference: Novell bnc#412548
https://bugzilla.novell.com/show_bug.cgi?id=412528
Added a quirk for another Acer Aspier laptop (1025:0090) with ALC883
codec. Reported in Novell bnc#426935:
https://bugzilla.novell.com/show_bug.cgi?id=426935
Some machines have broken BIOS resume that doesn't restore the default
pin configuration properly, which results in a wrong detection of HP
pin. This causes a silent speaker output due to missing HP detection.
Related bug: Novell bug#406101
https://bugzilla.novell.com/show_bug.cgi?id=406101
This patch fixes the issue by saving/restoring the default pin configs
by the driver itself.
Use 6STACK_DIG for the AD2000BX variant of the AD1989B chip used by Asus
on their Asus P5Q Premium and Pro boards.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SPDIF pins for AD1989 are not enabled by default. Set OUT bit so that they
actually work. Also initialize the HDMI SPDIF at the same time.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds sound support for NEC Versa S9100
With it, we get sound on the internal speaker and headphone (with
automute working) while there is no sound by default.
External mic also works fine but I don't know if there is an internal
one (if there is an internal mic it does not work currently), and I
had to send back the hardware.
The Pincap output had a typod format specifier, leading to an extraneous "08"
in the output, which is a reserved bit of the Vref field, and was really
confused :-).
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The camera reports an incorrect size and fails to handle PREVENT-ALLOW
MEDIUM REMOVAL commands. The patch marks the camera as an unusual dev
and adds the flags to enable the workarounds for both shortcomings.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is an entry for the unusual_devs.h file to handle a Mio Moov 330 GPS that
stops responding when it is requested to transfer more than 64KB. The patch is
taken against kernel-2.6.27-git3.
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
The edac driver on cell turned out to be not enabled because of a missing
op_state. This patch introduces it. Verified to work on top of Ben's
next branch.
Dell XPS M1530 needs i8042.nomux=1 for ALPS touchpad to work as
reported on https://qa.mandriva.com/show_bug.cgi?id=43532
It is said that before A08 bios version this isn't needed (I don't
have the hardware so can't check), and suppose this will not break
with bios versions before A08.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Tested-by: Andreas Ericsson <ae@op5.se> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thinkpad R31 needs i8042 nomux quirk. Stops jittery jumping mouse
and random keyboard input. Fixes kernel bug #11723. Cherry picked
from Ubuntu who have sometimes (on-again-off-again) had a fix in
their patched kernels.
Signed-off-by: Colin B Macdonald <cbm@m.fsf.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU. It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.
As far as I can tell, the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.
This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
As reported by Hugo Dias that it is possible to cause a local denial
of service attack by calling the svc_listen function twice on the same
socket and reading /proc/net/atm/*vc
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__try_to_free_cp_buf(), __process_buffer(), and __wait_cp_io() test
BH_Uptodate flag to detect write I/O errors on metadata buffers. But by
commit 95450f5a7e53d5752ce1a0d0b8282e10fe745ae0 "ext3: don't read inode
block if the buffer has a write error"(*), BH_Uptodate flag can be set to
inode buffers with BH_Write_EIO in order to avoid reading old inode data.
So now, we have to test BH_Write_EIO flag of checkpointing inode buffers
instead of BH_Uptodate. This patch does it.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Acked-by: Jan Kara <jack@suse.cz> Acked-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a checkpointing IO fails, current JBD code doesn't check the error
and continue journaling. This means latest metadata can be lost from both
the journal and filesystem.
This patch leaves the failed metadata blocks in the journal space and
aborts journaling in the case of log_do_checkpoint(). To achieve this, we
need to do:
1. don't remove the failed buffer from the checkpoint list where in
the case of __try_to_free_cp_buf() because it may be released or
overwritten by a later transaction
2. log_do_checkpoint() is the last chance, remove the failed buffer
from the checkpoint list and abort the journal
3. when checkpointing fails, don't update the journal super block to
prevent the journaled contents from being cleaned. For safety,
don't update j_tail and j_tail_sequence either
4. when checkpointing fails, notify this error to the ext3 layer so
that ext3 don't clear the needs_recovery flag, otherwise the
journaled contents are ignored and cleaned in the recovery phase
5. if the recovery fails, keep the needs_recovery flag
6. prevent cleanup_journal_tail() from being called between
__journal_drop_transaction() and journal_abort() (a race issue
between journal_flush() and __log_wait_for_space()
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Acked-by: Jan Kara <jack@suse.cz> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Apple boxes evidently require us to set SCI_EN on resume
directly, because if we don't do that, they hung somewhere in the
resume code path. Moreover, on these boxes it is not sufficient to
use acpi_enable() to turn ACPI on during resume. All of this is
against the ACPI specification which states that (1) the BIOS is
supposed to return from the S3 sleep state with ACPI enabled
(SCI_EN set) and (2) the SCI_EN bit is owned by the hardware and we
are not supposed to change it.
For this reason, blacklist the affected systems so that the SCI_EN
bit is set during resume on them.
[NOTE: Unconditional setting SCI_EN for all system on resume doesn't
work, because it makes some other systems crash (that's to be
expected). Also, it is not entirely clear right now if all of the
Apple boxes require this workaround.]
This patch fixes the recent regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12038
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Tino Keitel <tino.keitel@gmx.de> Tested-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changeset a238b790d5f99c7832f9b73ac8847025815b85f7 (Call fasync()
functions without the BKL) introduced a race which could leave
file->f_flags in a state inconsistent with what the underlying
driver/filesystem believes. Revert that change, and also fix the same
races in ioctl_fioasync() and ioctl_fionbio().
This is a minimal, short-term fix; the real fix will not involve the
BKL.
There's no point in having too short SG_IO timeouts, since if the
command does end up timing out, we'll end up through the reset sequence
that is several seconds long in order to abort the command that timed
out.
As a result, shorter timeouts than a few seconds simply do not make
sense, as the recovery would be longer than the timeout itself.
Add a BLK_MIN_SG_TIMEOUT to match the existign BLK_DEFAULT_SG_TIMEOUT.
Copy the FPU state to the task's thread_info->fpregs for the VIS emulation
functions to access.
Signed-off-by: Hong H. Pham <hong.pham@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes some bugs in VIS emulation that cause the GCC test
failure
FAIL: gcc.target/sparc/pdist-3.c execution test
for both 32-bit and 64-bit testing on hardware lacking these
instructions. The emulation code for the pdist instruction uses
RS1(insn) for both source registers rs1 and rs2, which is obviously
wrong and leads to the instruction doing nothing (the observed
problem), and further inspection of the code shows that RS1 uses a
shift of 24 and RD a shift of 25, which clearly cannot both be right;
examining SPARC documentation indicates the correct shift for RS1 is
14.
This patch fixes the bug if single-stepping over the affected
instruction in the debugger, but not if the testcase is run
standalone. For that, Wind River has another patch I hope they will
send as a followup to this patch submission.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
>The SPARC64 kernel code for PTRACE_SETFPREGS64 appears to be an exact copy
>of that for PTRACE_GETFPREGS64. This means that gdbserver and native
>64-bit GDB cannot set floating-point registers.
It looks like a simple typo.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a problem discovered in recent versions of ATI Mach64 driver
in X.org on sparc64 architecture. In short, the driver fails to mmap
MMIO aperture (PCI resource #2).
I've found that kernel's __pci_mmap_make_offset() returns EINVAL. It
checks whether user attempts to mmap more than the resource length,
which is 0x1000 bytes in our case. But PAGE_SIZE on SPARC64 is 0x2000
and this is what actually is being mmaped. So __pci_mmap_make_offset()
failed for this PCI resource.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov reports oops in __bzero() called from
copy_from_user_fixup() called from iov_iter_copy_from_user_atomic(),
when running dbench on tmpfs on sparc64: its __copy_from_user_inatomic
and __copy_to_user_inatomic should be avoiding, not calling, the fixups.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current UDP multicast delivery is not namespace aware.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Acked-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently libata uses four methods to detect device presence.
1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine
Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe. In both cases, PHY status wasn't available. In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4. The other failed #2 but as it passed #3 and #4,
it still caused failure.
In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.
In ordered mode, if a file data buffer being dirtied exists in the
committing transaction, we write the buffer to the disk, move it from the
committing transaction to the running transaction, then dirty it. But we
don't have to remove the buffer from the committing transaction when the
buffer couldn't be written out, otherwise it would miss the error and the
committing transaction would not abort.
This patch adds an error check before removing the buffer from the
committing transaction.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Acked-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could run into ENOSPC error on ext3, even when there is free blocks on
the filesystem.
The problem is triggered in the case the goal block group has 0 free
blocks , and the rest block groups are skipped due to the check of
"free_blocks < windowsz/2". Current code could fall back to non
reservation allocation to prevent early ENOSPC after examing all the block
groups with reservation on , but this code was bypassed if the reservation
window is turned off already, which is true in this case.
This patch fixed two issues:
1) We don't need to turn off block reservation if the goal block group has
0 free blocks left and continue search for the rest of block groups.
Current code the intention is to turn off the block reservation if the
goal allocation group has a few (some) free blocks left (not enough for
make the desired reservation window),to try to allocation in the goal
block group, to get better locality. But if the goal blocks have 0 free
blocks, it should leave the block reservation on, and continues search for
the next block groups,rather than turn off block reservation completely.
2) we don't need to check the window size if the block reservation is off.
The problem was originally found and fixed in ext4.
We could run into ENOSPC error on ext2, even when there is free blocks on
the filesystem.
The problem is triggered in the case the goal block group has 0 free
blocks , and the rest block groups are skipped due to the check of
"free_blocks < windowsz/2". Current code could fall back to non
reservation allocation to prevent early ENOSPC after examing all the block
groups with reservation on , but this code was bypassed if the reservation
window is turned off already, which is true in this case.
This patch fixed two issues:
1) We don't need to turn off block reservation if the goal block group has
0 free blocks left and continue search for the rest of block groups.
Current code the intention is to turn off the block reservation if the
goal allocation group has a few (some) free blocks left (not enough for
make the desired reservation window),to try to allocation in the goal
block group, to get better locality. But if the goal blocks have 0 free
blocks, it should leave the block reservation on, and continues search for
the next block groups,rather than turn off block reservation completely.
2) we don't need to check the window size if the block reservation is off.
The problem was originally found and fixed in ext4.
When trying to resize a ext3 fs and you run out of reserved gdt blocks,
you get an error that doesn't actually tell you what went wrong, it just
says that the gdb it picked is not correct, which is the case since you
don't have any reserved gdt blocks left. This patch adds a check to make
sure you have reserved gdt blocks to use, and if not prints out a more
relevant error.
Signed-off-by: Josef Bacik <jbacik@redhat.com> Cc: <linux-ext4@vger.kernel.org> Cc: Andreas Dilger <adilger@sun.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a regression caused by commit 6a897cf4, "ext3: fix ext3_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
When initializing an uninitialized block group in ext4_new_inode(),
its block group checksum must be re-calculated. This fixes a race
when several threads try to allocate a new inode in an UNINIT'd group.
There is some question whether we need to be initializing the block
bitmap in ext4_new_inode() at all, but for now, if we are going to
init the block group, let's eliminate the race.
This fixes a 2.6.27 regression which was introduced in commit a02908f1.
We weren't passing the chunk parameter down to the two subections,
ext4_indirect_trans_blocks() and ext4_ext_index_trans_blocks(), with
the result that massively overestimate the amount of credits needed by
ext4_da_writepages, especially in the non-extents case. This causes
failures especially on /boot partitions, which tend to be small and
non-extent using since GRUB doesn't handle extents.
This patch fixes the bug reported by Joseph Fannin at:
http://bugzilla.kernel.org/show_bug.cgi?id=11964
In ext4_sync_fs, we only wait for a commit to finish if we started it,
but there may be one already in progress which will not be synced.
In the case of a data=ordered umount with pending long symlinks which
are delayed due to a long list of other I/O on the backing block
device, this causes the buffer associated with the long symlinks to
not be moved to the inode dirty list in the second phase of
fsync_super. Then, before they can be dirtied again, kjournald exits,
seeing the UMOUNT flag and the dirty pages are never written to the
backing block device, causing long symlink corruption and exposing new
or previously freed block data to userspace.
To ensure all commits are synced, we flush all journal commits now
when sync_fs'ing ext4.
Signed-off-by: Arthur Jones <ajones@riverbed.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Cc: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 23f8b79e introducd a regression because it assumed that if
there were no transactions ready to be checkpointed, that no progress
could be made on making space available in the journal, and so the
journal should be aborted. This assumption is false; it could be the
case that simply calling jbd2_cleanup_journal_tail() will recover the
necessary space, or, for small journals, the currently committing
transaction could be responsible for chewing up the required space in
the log, so we need to wait for the currently committing transaction
to finish before trying to force a checkpoint operation.
This patch fixes a bug reported by Mihai Harpau at:
https://bugzilla.redhat.com/show_bug.cgi?id=469582
This patch fixes a bug reported by François Valenduc at:
http://bugzilla.kernel.org/show_bug.cgi?id=11840
Fix a regression caused by commit d0156417, "ext4: fix ext4_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
During filesystem recovery we may be doing a truncate
which expects some of the mballoc data structures to
be initialized. So do ext4_mb_init before recovery.
ext4_xattr_set_handle() eventually ends up calling
ext4_mark_inode_dirty() which tries to expand the inode by shifting
the EAs. This leads to the xattr_sem being downed again and leading
to a deadlock.
This patch makes sure that if ext4_xattr_set_handle() is in the
call-chain, ext4_mark_inode_dirty() will not expand the inode.
Also make sure the buffer heads are marked clean before submitting bh
for writing. The previous code was marking the buffer head dirty,
which would have forced an unneeded write (and seek) to the journal
for no good reason.
The __jbd2_log_wait_for_space function sits in a loop checkpointing
transactions until there is sufficient space free in the journal.
However, if there are no transactions to be processed (e.g. because the
free space calculation is wrong due to a corrupted filesystem) it will
never progress.
Check for space being required when no transactions are outstanding and
abort the journal instead of endlessly looping.
This patch fixes the bug reported by Sami Liedes at:
http://bugzilla.kernel.org/show_bug.cgi?id=10976
Pick an ioctl number for EXT4_IOC_MIGRATE that won't conflict with
other ext4 ioctl's. Since there haven't been any major userspace
users of this ioctl, we can afford to change this now, to avoid
potential problems later.
Also, reorder the ioctl numbers in ext4.h to avoid this sort of
mistake in the future.
If there group descriptors are corrupted we need unlock the block
group lock before returning from the function; else we will oops when
freeing a spinlock which is still being held.
Some devices such as "cciss/c0d0p9" will cause jbd2 setup and teardown
failures when /proc filenames are created with embedded slashes. This
is a slimmed down version of commit 05496769, with the stack reduction
aspects of the patch omitted to meet the -stable criteria.
prevent cifs_writepages() from skipping unwritten pages
Fixes a data corruption under heavy stress in which pages could be left
dirty after all open instances of a inode have been closed.
In order to write contiguous pages whenever possible, cifs_writepages()
asks pagevec_lookup_tag() for more pages than it may write at one time.
Normally, it then resets index just past the last page written before calling
pagevec_lookup_tag() again.
If cifs_writepages() can't write the first page returned, it wasn't resetting
index, and the next call to pagevec_lookup_tag() resulted in skipping all of
the pages it previously returned, even though cifs_writepages() did nothing
with them. This can result in data loss when the file descriptor is about
to be closed.
This patch ensures that index gets set back to the next returned page so
that none get skipped.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Acked-by: Jeff Layton <jlayton@redhat.com> Cc: Shirish S Pargaonkar <shirishp@us.ibm.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use a similar approach to the SMB session sharing. Add a list of tcons
attached to each SMB session. Move the refcount to non-atomic. Protect
all of the above with the cifs_tcp_ses_lock. Add functions to
properly find and put references to the tcons.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do this by abandoning the global list of SMB sessions and instead
moving to a per-server list. This entails adding a new list head to the
TCP_Server_Info struct. The refcounting for the cifsSesInfo is moved to
a non-atomic variable. We have to protect it by a lock anyway, so there's
no benefit to making it an atomic. The list and refcount are protected
by the global cifs_tcp_ses_lock.
The patch also adds a new routines to find and put SMB sessions and
that properly take and put references under the lock.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code that allows these structs to be shared is extremely racy.
Disable the sharing of SMB and tcon structs for now until we can
come up with a way to do this that's race free.
We want to continue to share TCP sessions, however since they are
required for multiuser mounts. For that, implement a new (hopefully
race-free) scheme. Add a new global list of TCP sessions, and take
care to get a reference to it whenever we're dealing with one.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We're currently declaring both a sockaddr_in and sockaddr6_in on the
stack, but we really only need storage for one of them. Declare a
sockaddr struct and cast it to the proper type. Also, eliminate the
protocolType field in the TCP_Server_Info struct. It's redundant since
we have a sa_family field in the sockaddr anyway.
We may need to revisit this if SCTP is ever implemented, but for now
this will simplify the code.
CIFS over IPv6 also has a number of problems currently. This fixes all
of them that I found. Eventually, it would be nice to move more of the
code to be protocol independent, but this is a start.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Cc: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log