Christian König [Fri, 26 Jun 2015 10:31:29 +0000 (12:31 +0200)]
drm/radeon: fix adding all VAs to the freed list on remove v2
We only should do so when the BO_VA was actually mapped.
Otherwise we get a nice error message on the next CS.
v2: It actually doesn't matter if it was invalidated or not,
if it was mapped we need to clear the area where it was mapped.
Signed-off-by: Christian König <christian.koenig@amd.com> Tested-by: Michel Dänzer <michel.daenzer@amd.com> (v1) Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jérôme Glisse [Fri, 19 Jun 2015 14:32:16 +0000 (10:32 -0400)]
drm/radeon: SDMA fix hibernation (CI GPU family).
In order for hibernation to reliably work we need to properly turn
off the SDMA block, sadly after numerous attemps i haven't not found
proper sequence for clean and full shutdown. So simply reset both
SDMA block, this makes hibernation works reliably on sea island GPU
family (CI)
Hibernation and suspend to ram were tested (several times) on :
Bonaire
Hawaii
Mullins
Kaveri
Kabini
Cc: stable@vger.kernel.org Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jérôme Glisse [Fri, 19 Jun 2015 14:32:15 +0000 (10:32 -0400)]
drm/radeon: compute ring fix hibernation (CI GPU family) v2.
In order for hibernation to reliably work we need to cleanup more
thoroughly the compute ring. Hibernation is different from suspend
resume as when we resume from hibernation the hardware is first
fully initialize by regular kernel then freeze callback happens
(which correspond to a suspend inside the radeon kernel driver)
and turn off each of the block. It turns out we were not cleanly
shutting down the compute ring. This patch fix that.
Hibernation and suspend to ram were tested (several times) on :
Bonaire
Hawaii
Mullins
Kaveri
Kabini
Changed since v1:
- Factor the ring stop logic into a function taking ring as arg.
Cc: stable@vger.kernel.org Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
On the MacBook Pro, power of the gpu is cut by a gmux chip. Sometimes
the gpu gets stuck in powersaving mode and refuses to wake up
("Refused to change power state, currently in D3"). Inserting a
delay between setting the gpu to D3hot and cutting the power seems
to help (most of the time). This issue and its (partial) remediation
by the patch was observed with an Nvidia GT650M (NVE7 / GK107).
Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 15 Jun 2015 00:34:28 +0000 (10:34 +1000)]
drm/dp/mst: close deadlock in connector destruction.
I've only seen this once, and I failed to capture the
lockdep backtrace, but I did some investigations.
If we are calling into the MST layer from EDID probing,
we have the mode_config mutex held, if during that EDID
probing, the MST hub goes away, then we can get a deadlock
where the connector destruction function in the driver
tries to retake the mode config mutex.
This offloads connector destruction to a workqueue,
and avoid the subsequenct lock ordering issue.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Stone [Tue, 23 Jun 2015 13:18:58 +0000 (14:18 +0100)]
drm: Always enable atomic API
Now that the interface has been proven by a port of Weston (using all
atomic features including TEST_ONLY), remove the module parameter
guarding the atomic API from being exposed, and let it run free in the
wild.
Signed-off-by: Daniel Stone <daniels@collabora.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Tue, 23 Jun 2015 14:35:06 +0000 (16:35 +0200)]
drm/vgem: Set unique to "vgem"
Since there's only one global instance ever we don't need to have
anything fancy. Stops a WARNING in the get_unique ioctl that the
unique name isn't set.
Cc: <stable@vger.kernel.org> # 4.1+ only Reportedy-and-tested-by: Fabio Coatti <fabio.coatti@gmail.com> Cc: Fabio Coatti <fabio.coatti@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki Dae [Tue, 23 Jun 2015 07:06:44 +0000 (16:06 +0900)]
of: fix a build error to of_graph_get_endpoint_by_regs function
This patch fixes the below build error reported by Stephen,
Stephen reported:
After merging the drm-exynos tree, today's linux-next build (x86_64
allmodconfig) failed like this:
drivers/media/i2c/adv7604.o: In function `of_graph_get_endpoint_by_regs':
adv7604.c:(.text+0x586c): multiple definition of `of_graph_get_endpoint_by_regs'
drivers/media/i2c/adv7343.o:adv7343.c:(.text+0xa13): first defined here
drivers/media/platform/soc_camera/atmel-isi.o: In function `of_graph_get_endpoint_by_regs':
atmel-isi.c:(.text+0x1ec9): multiple definition of `of_graph_get_endpoint_by_regs'
drivers/media/platform/soc_camera/soc_camera.o:soc_camera.c:(.text+0x2ce3): first defined here
drivers/media/platform/soc_camera/rcar_vin.o: In function `of_graph_get_endpoint_by_regs':
rcar_vin.c:(.text+0x307c): multiple definition of `of_graph_get_endpoint_by_regs'
drivers/media/platform/soc_camera/soc_camera.o:soc_camera.c:(.text+0x2ce3): first defined here
Caused by commit: a0f7001c18ca ("of: add helper for getting endpoint node of specific identifiers")
To fix the error, this patch declares of_graph_get_endpoint_by_regs function
with "static inline".
Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 22 Jun 2015 04:40:44 +0000 (14:40 +1000)]
drm/dp/mst: take lock around looking up the branch device on hpd irq
If we are doing an MST transaction and we've gotten HPD and we
lookup the device from the incoming msg, we should take the mgr
lock around it, so that mst_primary and mstb->ports are valid.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter [Mon, 22 Jun 2015 07:31:59 +0000 (17:31 +1000)]
drm/dp/mst: make sure mst_primary mstb is valid in work function
This validates the mst_primary under the lock, and then calls
into the check and send function. This makes the code a lot
easier to understand the locking rules in.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 23 Jun 2015 00:22:19 +0000 (10:22 +1000)]
Merge tag 'drm-intel-next-fixes-2015-06-22' of git://anongit.freedesktop.org/drm-intel into drm-next
fix warning introduced in last -fixes
* tag 'drm-intel-next-fixes-2015-06-22' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Silence compiler warning
Dave Airlie [Tue, 23 Jun 2015 00:13:18 +0000 (10:13 +1000)]
Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Summary:
. Add atomic feature support
- Exynos also now supports atomic feature. However, it doesn't
guarantee atomic operation yet, and is required for more cleanups.
This time we just modified for Exynos drm driver to use atomic
interfaces instead of legacy ones. Next time, we will enhance
Exynos drm driver to support the atomic operation.
. Add iommu support
- This is a patch series according to below Exynos iommu integration
work with DT and dma-mapping subsystem,
http://lwn.net/Articles/607626/
. Consolidate Exynos drm driver initialization.
- This patch sereis resolves the issue that only the first compoments
was bound when happened deferred probing for other pipelines and
also makes the driver to be more cleanned up by moving the dispered
codes for registering kms drivers to one place.
. Add new MIC, DECON drivers, and MIPI-DSI support for Exynos5433.
- Add MIC(Mobile image compressor) driver. MIC is a new IP for Exynos5433
and later, which is used to transfer frame data to MIPI-DSI controller
compressing the data to reduce memory bandwidth.
- Add DECON driver for Exynos5433 SoC. This IP is a dislay controller
similar to Exynos7's one but this controller has much different registers
from Exynos7's ones so this driver has been implemented separately.
We will implement a helper modules for FIMD and two DECON controllers
to remove duplicated codes later.
- Add Exynos5433 SoC support to MIPI-DSI driver, and device tree
relevant patches.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (50 commits)
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
drm/exynos: fix the input prompt of Exynos7 DECON
drm/exynos: add drm_iommu_attach_device_if_possible()
drm/exynos: Add the dependency for DRM_EXYNOS to DPI/DSI/DP
drm/exynos: remove the dependency of DP driver for ARCH_EXYNOS
drm/exynos: do not wait for vblank at atomic operation
drm/exynos: Remove unused vma field of exynos_drm_gem_obj
drm/exynos: fimd: fix page fault issue with iommu
drm/exynos: iommu: improve a check for non-iommu dma_ops
drm/exynos: iommu: detach from default dma-mapping domain on init
...
Dave Airlie [Tue, 23 Jun 2015 00:12:40 +0000 (10:12 +1000)]
Merge tag 'topic/drm-misc-2015-06-22' of git://anongit.freedesktop.org/drm-intel into drm-next
One more drm-misc pull for 4.2. The important one is the fix from Laurent
for Daniel Stone's mode_blob work.
* tag 'topic/drm-misc-2015-06-22' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: Don't set crtc_state->enable manually
drm: prime: Document gem_prime_mmap
drm: Avoid the double clflush on the last cache line in drm_clflush_virt_range()
drm/atomic: Extract needs_modeset function
drm/cma: Fix 64-bit size_t build warnings
Documentation/drm: Update rotation property
Laurent Pinchart [Mon, 22 Jun 2015 10:37:46 +0000 (13:37 +0300)]
drm/atomic: Don't set crtc_state->enable manually
The enable field needs to be kept in sync with the mode_blob field. Call
drm_atomic_set_mode_prop_for_crtc() instead of setting enable to false
in order to dereference the mode blob correctly.
v2:
- Check the return value of drm_atomic_set_mode_prop_for_crtc()
- Drop the num_connectors local variable
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:09 +0000 (21:59 +0900)]
drm/exynos: dsi: do not set TE GPIO direction by input
On some board, TE GPIO should be configured properly thoughout pinctrl driver
as an wakeup interrupt. So this gpio should be configurable in the board's DT,
not being requested as a input pin.
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:06 +0000 (21:59 +0900)]
drm/exynos: dsi: make use of array for clock access
This patch make the driver to use an array for clock access. The number
of clocks are different from the existing MIPI DSI driver and Exynos5433
MIPI DSI driver. So this patch is needed before adding support for
Exynos5433 MIPI DSI driver.
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:05 +0000 (21:59 +0900)]
drm/exynos: dsi: make use of driver data for static values
Exynos MIPI DSI driver uses some static values such as address offsets,
register setting values, and etc. This patch makes the driver get those
values from the driver data.
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:04 +0000 (21:59 +0900)]
drm/exynos: dsi: add macros for register access
This patch adds macros for register writing/reading. This is needed for
adding support Exynos5433 MIPI DSI driver, not by using if statement, but
by using driver data.
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:03 +0000 (21:59 +0900)]
drm/exynos: dsi: rename pll_clk to sclk_clk
This patch renames pll_clk to sclk_clk. The clock referenced by pll_clk
is actually not the pll input clock for dsi. The pll input clock comes
from the board's oscillator directly. But for the backward
compatibility, the old clock name "pll_clk" is also OK.
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:02 +0000 (21:59 +0900)]
drm/exynos: mic: add MIC driver
MIC(Mobile image compressor) is newly added IP in Exynos5433. MIC
resides between decon and mipi dsim, and compresses frame data by 50%.
With dsi, not display port, to send frame data to the panel, the
bandwidth is not enough. That is why this compressor is introduced.
Hyungwon Hwang [Fri, 12 Jun 2015 12:59:01 +0000 (21:59 +0900)]
of: add helper for getting endpoint node of specific identifiers
When there are multiple ports or multiple endpoints in a port, they have to be
distinguished by the value of reg property. It is common. The drivers can get
the specific endpoint in the specific port via this function. Now the drivers
have to implement this code in themselves or have to force the order of dt nodes
to get the right node.
Every CRTC drivers in Exynos DRM implements the code which checks
whether IOMMU is supported or not, and if supported enable it.
Making new helper for it generalize each CRTC drivers.
Hyungwon Hwang [Fri, 12 Jun 2015 12:58:57 +0000 (21:58 +0900)]
drm/exynos: Add the dependency for DRM_EXYNOS to DPI/DSI/DP
Without this dependency, Kbuild is confused and the configs below
them are not placed under Exynos DRM. This patch fixes it, so the
configs below them become to be placed under Exynos DRM.
Hyungwon Hwang [Fri, 12 Jun 2015 12:58:56 +0000 (21:58 +0900)]
drm/exynos: remove the dependency of DP driver for ARCH_EXYNOS
This dependency is a historical thing. It is added when this DP driver is
under media subsystem. Now because it is under Exynos DRM, this dependency
is not needed anymore.
Silence the following -Wmaybe-uninitialized warnings and make the code
more clear.
drivers/gpu/drm/i915/intel_display.c: In function ‘__intel_set_mode’:
drivers/gpu/drm/i915/intel_display.c:11844:14: warning: ‘crtc_state’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return state->mode_changed || state->active_changed;
^
drivers/gpu/drm/i915/intel_display.c:11854:25: note: ‘crtc_state’ was declared here
struct drm_crtc_state *crtc_state;
^
drivers/gpu/drm/i915/intel_display.c:11868:6: warning: ‘crtc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (crtc != intel_encoder->base.crtc)
^
drivers/gpu/drm/i915/intel_display.c:11853:19: note: ‘crtc’ was declared here
struct drm_crtc *crtc;
Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Inki Dae [Fri, 19 Jun 2015 11:53:03 +0000 (20:53 +0900)]
drm/exynos: do not wait for vblank at atomic operation
This patch resolves the issue that refresh rate got low
at extension mode test with fimd and vidi combination.
The problem was because atomic_commit callback waited
for the completion of vblank to gaurantee crtc relevant
registers are updated from shadow registers to real ones.
However, the waiting there is really unnecessary because
page flip operation does already it.
drm/exynos: Remove unused vma field of exynos_drm_gem_obj
The field 'vma' of 'exynos_drm_gem_obj' structure was introduced in 2a3098ff6c21 ("drm/exynos: add userptr feature for g2d module") but is
not referenced anywhere.
One instance of 'exynos_drm_gem_obj' may be mapped to multiple
user-space VMAs so 'vma' field does not look useful anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Inki Dae [Fri, 12 Jun 2015 13:19:22 +0000 (22:19 +0900)]
drm/exynos: fimd: fix page fault issue with iommu
This patch resolves page fault issue with iommu and atomic feature
when modetest test application is terminated.
ENWIN_F field of WINCONx register enables or disable a dma channel to
each hardware overlay - the value of the field will be updated to real
register after vsync.
So this patch makes sure the dma channel is disabled by waiting for vsync
one time after clearing shadow registers to all dma channels.
Below shows the page fault issue:
setting mode 720x1280-60Hz@XR24 on connectors 31, crtc 29
freq: 59.99Hz
[ 34.831025] PAGE FAULT occurred at 0x20400000 by 11e20000.sysmmu(Page
table base: 0x6e324000)
[ 34.838072] Lv1 entry: 0x6e92dc01
[ 34.841489] ------------[ cut here ]------------
[ 34.846058] kernel BUG at drivers/iommu/exynos-iommu.c:364!
[ 34.851614] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 34.857428] Modules linked in:
<--snip-->
[ 35.210894] [<c02880d0>] (exynos_sysmmu_irq) from [<c00608f8>]
(handle_irq_event_percpu+0x78/0x134)
[ 35.219914] [<c00608f8>] (handle_irq_event_percpu) from [<c00609f0>]
(handle_irq_event+0x3c/0x5c)
[ 35.228768] [<c00609f0>] (handle_irq_event) from [<c0063698>]
(handle_level_irq+0xc4/0x13c)
[ 35.237101] [<c0063698>] (handle_level_irq) from [<c005ff7c>]
(generic_handle_irq+0x2c/0x3c)
[ 35.245521] [<c005ff7c>] (generic_handle_irq) from [<c02214ec>]
(combiner_handle_cascade_irq+0x94/0x100)
[ 35.254980] [<c02214ec>] (combiner_handle_cascade_irq) from
[<c005ff7c>] (generic_handle_irq+0x2c/0x3c)
[ 35.264353] [<c005ff7c>] (generic_handle_irq) from [<c0060248>]
(__handle_domain_irq+0x7c/0xec)
[ 35.273034] [<c0060248>] (__handle_domain_irq) from [<c0009434>]
(gic_handle_irq+0x30/0x68)
[ 35.281366] [<c0009434>] (gic_handle_irq) from [<c0012ec0>]
(__irq_svc+0x40/0x74)
drm/exynos: iommu: improve a check for non-iommu dma_ops
DRM Exynos driver is relying on dma-mapping internal structures when used
with IOMMU enabled. This patch partially hides dma-mapping internal things
by using proper get_dma_ops/set_dma_ops calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
drm/exynos: iommu: detach from default dma-mapping domain on init
This patch adds code, which detach sub-device nodes from default iommu
domain if such has been configured. This lets Exynos DRM driver to properly
attach sub-devices to its own, common for all sub-devices domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Marek Szyprowski [Fri, 12 Jun 2015 09:07:17 +0000 (11:07 +0200)]
drm/exynos: fimd: ensure proper hw state in fimd_clear_channel()
One should not do any assumptions on the stare of the fimd hardware
during driver initialization, so to properly reset fimd before enabling
IOMMU, one should ensure that all power domains and clocks are really
enabled. This patch adds pm_runtime and clocks management in the
fimd_clear_channel() function to ensure that any access to fimd
registers will be performed with clocks and power domains enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Joonyoung Shim [Fri, 12 Jun 2015 08:27:16 +0000 (17:27 +0900)]
drm/exynos: initialize VIDCON0 when fimd is disabled
When the fimd is disabled by fimd_disable(), enabled overlay layers also
are disabled. If clocks for fimd are enabled by fimd_enable() on this
case, it can lead IOMMU page fault. The reason is that VIDCON0_ENVID and
VIDCON0_ENVID_F bits of VIDCON0 register are set still even though fimd
is disabled, so it may continue display output of prior when clocks for
fimd are enabled again.
Joonyoung Shim [Fri, 12 Jun 2015 11:34:28 +0000 (20:34 +0900)]
drm/exynos: remove chained calls to enable
With atomic modesetting all the control for CRTC, Planes, Encoders and
Connectors should come from DRM core, so the driver is not allowed to
enable or disable planes from inside the crtc_enable()/disable() call.
But it needs to disable planes with crtc_disable in exynos driver
internally. Because crtc is disabled before plane is disabled, it means
plane_disable just returns without any register changes, then we cannot
be sure setting register to disable plane when crtc is disable.
This patch removes this chainned calls to enable plane from exynos hw
drivers code letting only DRM core touch planes except to disable plane.
Also it leads eliminable enabled and resume of struct exynos_drm_plane.
Joonyoung Shim [Fri, 12 Jun 2015 08:27:14 +0000 (17:27 +0900)]
drm/exynos: remove to call mixer_wait_for_vblank
The reason waiting vblank is to be power gated and disabled clocks after
dma operation is completed. The dma operation is stopped already before
be power gated and clocks are disabled when mixer is disabled by commit 381be025ac1a6("drm/exynos: stop mixer before gating clocks during
poweroff"). Don't need to wait vblank anymore.
Hyungwon Hwang [Tue, 9 Jun 2015 03:45:15 +0000 (12:45 +0900)]
drm/exynos: ipp: validate a GEM handle with multiple planes
FIMC & GSC driver can calculate the offset of planes. So there are
use cases which IPP receives just one GEM handle of an image with
multiple plane. This patch extends ipp_validate_mem_node() to validate
this case.
Hyungwon Hwang [Thu, 11 Jun 2015 14:40:30 +0000 (23:40 +0900)]
drm/exynos: dsi: check whether dsi is enabled before sending data
exynos_dsi_host_transfer() can be called through a panel driver while
DSI is turning down. It is possible because the function checks only
whether DSI is initialized or not, and there is a moment which DSI is
set by uninitialized, but DSI is still turning down. To prevent it,
DSI must be set by disabled before starting to be turned down, and
exynos_dsi_host_transfer() must check whether DSI is enabled or not.
Andrzej Hajda [Mon, 8 Jun 2015 10:15:42 +0000 (12:15 +0200)]
drm/exynos: remove SoC checking code
SoC checking code is not necessary anymore, as exynos_drm_match_add and
exynos_drm_platform_probe already properly handles situation when there are
no Exynos DRM components.
Andrzej Hajda [Thu, 11 Jun 2015 14:23:37 +0000 (23:23 +0900)]
drm/exynos: fix broken component binding in case of multiple pipelines
In case there are multiple pipelines and deferred probe occurs, only components
of the first pipeline were bound. As a result only one pipeline was available.
The main cause of this issue was dynamic generation of component match table -
every component driver during probe registered itself on helper list, if there
was at least one pipeline present on this list component match table were
created without deferred components.
This patch removes this helper list, instead it creates match table from
existing devices requiring exynos_drm KMS drivers. This way match table do not
depend on probe/deferral order and contains all KMS components.
As a side effect patch makes the code cleaner and significantly smaller.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Code registering different drivers and simple platform devices was dispersed
across multiple sub-modules. This patch moves it to one place. As a result
initialization code is shorter and cleaner and should simplify further
development.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Gustavo Padovan [Mon, 1 Jun 2015 15:04:53 +0000 (12:04 -0300)]
drm/exynos: atomic dpms support
Run dpms operations through the atomic intefaces. This basically removes
the .dpms() callback from econders and crtcs and use .disable() and
.enable() to turn the crtc on and off.
v2: Address comments by Joonyoung:
- make hdmi code call ->disable() instead of ->dpms()
- do not use WARN_ON on crtc enable/disable
v3: - Fix build failure after the hdmi change in v2
- Change dpms helper of ptn3460 bridge
v4: - remove win_commit() call from .enable()
v5: - move .atomic_check() to the atomic PageFlip patch, and transform it
in .atomic_begin()
Gustavo Padovan [Mon, 1 Jun 2015 15:04:52 +0000 (12:04 -0300)]
drm/exynos: add exynos specific .atomic_commit()
exynos needs to update planes with the crtc enabled (mainly for the FIMD
case) so this specific atomic commit changes the order of
drm_atomic_helper_commit_modeset_enables() and
drm_atomic_helper_commit_planes() to commit planes after we enable crtc
and encoders.
Gustavo Padovan [Mon, 1 Jun 2015 15:04:51 +0000 (12:04 -0300)]
drm/exynos: move exynos_drm_crtc_disable()
This is a preparation commit to move exynos_drm_crtc_disable() together
with the future exynos_drm_crtc_enable() that will come from the split of
exynos_drm_crtc_dpms() callback.
Gustavo Padovan [Mon, 1 Jun 2015 15:04:49 +0000 (12:04 -0300)]
drm/exynos: remove exported functions from exynos_drm_plane
Now that no one is using the functions exported by exynos_drm_plane due
to the atomic conversion we can make remove some of the them or make them
static.
Gustavo Padovan [Mon, 1 Jun 2015 15:04:44 +0000 (12:04 -0300)]
drm/exynos: atomic phase 2: wire up state reset(), duplicate() and destroy()
Set CRTC, planes and connectors to use the default implementations from
the atomic helper library. The helpers will work to keep track of state
for each DRM object.
Gustavo Padovan [Mon, 1 Jun 2015 15:04:41 +0000 (12:04 -0300)]
drm/exynos: atomic phase 1: use drm_plane_helper_update()
Rip out the check from exynos_update_plane() and create
exynos_check_plane() for the check phase enabling use to use
the atomic helpers to call our check and update phases when updating
planes.
Update all users of exynos_update_plane() accordingly to call
exynos_check_plane() before.
Chris Wilson [Wed, 10 Jun 2015 14:58:01 +0000 (15:58 +0100)]
drm: Avoid the double clflush on the last cache line in drm_clflush_virt_range()
As the clflush operates on cache lines, and we can flush any byte
address, in order to flush all bytes given in the range we issue an
extra clflush on the last byte to ensure the last cacheline is flushed.
We can can the iteration to be over the actual cache lines to avoid this
double clflush on the last byte.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Imre Deak <imre.deak@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Fri, 19 Jun 2015 02:01:39 +0000 (12:01 +1000)]
Merge tag 'drm-intel-next-fixes-2015-06-18' of git://anongit.freedesktop.org/drm-intel into drm-next
i915 fixes for stuff in next
* tag 'drm-intel-next-fixes-2015-06-18' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Don't set enabled value of all CRTCs when restoring the mode
drm/i915: Don't update staged config during force restore modesets
drm/i915: Don't check modeset state in the hw state force restore path
drm/i915: Add SCRATCH1 and ROW_CHICKEN3 to the register whitelist.
drm/i915: Extend the parser to check register writes against a mask/value pair.
drm/i915: Fix command parser to validate multiple register access with the same command.
drm/i915: Don't skip request retirement if the active list is empty
Dave Airlie [Thu, 18 Jun 2015 03:01:04 +0000 (13:01 +1000)]
Merge branch 'virtio-gpu-drm-next' of git://git.kraxel.org/linux into drm-next
fixes and virtio-vga support.
* 'virtio-gpu-drm-next' of git://git.kraxel.org/linux:
virtio-gpu: add locking for vbuf pool
drm/virtgpu: initialise fbdev after getting initial display info
Add virtio-vga bits.
Dave Airlie [Thu, 18 Jun 2015 02:55:03 +0000 (12:55 +1000)]
Merge tag 'drm/panel/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.2-rc1
This contains fixes for the long-standing build issues that some of the
bridge drivers were exposing. Other than that it's mostly cleanup and a
couple of new simple panels that are supported.
* tag 'drm/panel/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: simple: Add bus format for HannStar HSD100PXN1
drm/panel: simple: Add display timing for HannStar HSD100PXN1
drm/panel: ld9040: Remove useless padding
drm/panel: Constify OF match tables
drm/bridge: Remove stale ptn3460.h include
drm/bridge: ps8622: Include linux/gpio/consumer.h
drm/bridge: ptn3460: Include linux/gpio/consumer.h
drm/bridge: dw-hdmi: Return number of EDID modes
drm/panel: simple: Add support for LG LB070WV8 800x480 7" panel
drm/bridge: ptn3460: Pass flags to devm_gpiod_get()
drm/bridge: ps8622: Pass flags to devm_gpiod_get()
drm/bridge: ptn3460: Fix I2C ID table to match the reported modalias
drm/bridge: dw-hdmi: Staticize dw_hdmi_bridge_funcs
Dave Airlie [Thu, 18 Jun 2015 02:53:54 +0000 (12:53 +1000)]
Merge tag 'drm/tegra/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.2-rc1
This contains a couple of mostly fixes for issues that have crept up in
recent versions of linux-next. One issue is that DP AUX transactions of
more than 4 bytes will access the wrong FIFO registers and hence become
corrupt. Another fix is required to restore functionality of Tegra20 if
using the GART. The current code expects the IOMMU aperture to be the
complete 4 GiB address space, whereas the GART on Tegra20 only provides
a 128 MiB aperture. One more issue with IOMMU support is that on 64-bit
ARM, swiotlb is the default IOMMU implementation backing the DMA API. A
side-effect of that is that when dma_map_sg() is called to flush caches
(yes, this is a bit of a hack, but ARM does not provide a better API),
swiotlb will immediately run out of memory because its bounce buffer is
too small to make a framebuffer.
Finally I've included a mostly cosmetic fix that stores register values
in u32 rather than unsigned long to avoid sign-extension issues on 64-
bit ARM. This is only a precaution since it hasn't caused any issues
(yet).
* tag 'drm/tegra/for-4.2-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: dpaux: Registers are 32-bit
drm/tegra: gem: Flush pages after allocation
drm/tegra: gem: Take into account IOMMU aperture
drm/tegra: dpaux: Fix transfers larger than 4 bytes
Dave Airlie [Thu, 18 Jun 2015 02:52:49 +0000 (12:52 +1000)]
Merge branch 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev into drm-next
rcar-du fixes
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm: rcar-du: Use the drm atomic state duplication helpers for planes
drm: rcar-du: Clean up planes in the error paths of .atomic_commit()
drm: rcar-du: Convert rcar_du_encoders_init_one() return value to 0/<0
drm: rcar-du: Clarify error message when encoder initialization fails
drm: rcar-du: Fix crash with groups that have less than 9 planes
drm: rcar-du: Disable all planes when stopping the CRTC
drm: rcar-du: Print the error value when DRM/KMS init fails
Dave Airlie [Thu, 18 Jun 2015 02:51:20 +0000 (12:51 +1000)]
Merge tag 'drm-amdkfd-next-fixes-2015-06-16' of git://people.freedesktop.org/~gabbayo/linux into drm-next
- Dan fixed some range checks in the address watch ioctl impl.
- Remove obsolete member from radeon_device structure
* tag 'drm-amdkfd-next-fixes-2015-06-16' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: fix some range checks in address watch ioctl
drm/radeon: remove obsolete kfd_bo from radeon_device
drm/i915: Don't set enabled value of all CRTCs when restoring the mode
The code in intel_crtc_restore_mode() sets the enabled value of all the
CRTCs when restoring the mode after a suspend/resume cycle. When more
than one CRTC is enabled, that causes drm_atomic_helper_check_modeset()
to fail if there is more than one pipe enabled, since all but one CRTC
has valid connector data. Instead, set only the enabled value for the
CRTC passed as an argument.
v2: Don't leak atomic state. (Matt)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90468
References: https://bugs.freedesktop.org/show_bug.cgi?id=90396 Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
drm/i915: Don't update staged config during force restore modesets
The force restore path relies on the staged config to preserve the
configuration used before a suspend/resume cycle. The update done to it
in intel_modeset_fixup_state() would cause that information to be lost
after the first modeset, making it impossible to restore the modes for
pipes B and C.
References: https://bugs.freedesktop.org/show_bug.cgi?id=90468 Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/i915: Don't check modeset state in the hw state force restore path
Since the force restore logic will restore the CRTCs state one at a
time, it is possible that the state will be inconsistent until the whole
operation finishes. A call to intel_modeset_check_state() is done once
it's over, so don't check the state multiple times in between. This
regression was introduced in:
drm/i915: factor out compute_config from __intel_set_mode v3
v2: Rename check parameter to force_restore. (Matt)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94431 Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Laurent Pinchart [Wed, 27 May 2015 13:36:29 +0000 (16:36 +0300)]
drm: rcar-du: Use the drm atomic state duplication helpers for planes
Ensure that the duplicate and destroy plane state operations will always
be in sync with the DRM core implementation of the plane state by using
the __drm_atomic_helper_plane_duplicate_state() and
__drm_atomic_helper_plane_destroy_state() functions designed especially
for this purpose.
Laurent Pinchart [Tue, 26 May 2015 23:14:37 +0000 (02:14 +0300)]
drm: rcar-du: Clean up planes in the error paths of .atomic_commit()
When the .atomic_commit() handler fails, clean up planes previoulsy
prepared by drm_atomic_helper_prepare_planes() with a call to
drm_atomic_helper_cleanup_planes().
Laurent Pinchart [Tue, 26 May 2015 12:07:56 +0000 (15:07 +0300)]
drm: rcar-du: Convert rcar_du_encoders_init_one() return value to 0/<0
The function returns 1 on success, and either 0 or a negative error code
on failure. As the 0 and negative values don't need to be differentiated
by the caller, convert it to the usual scheme of returning 0 on success
and a negative error code on failure.
projects / karo-tx-linux.git / log