Lothar Waßmann [Tue, 24 Oct 2017 13:18:48 +0000 (15:18 +0200)]
ARM: dts: imx6ul-txul: use panel-simple driver for LCD
Convert the TXUL board support to use the panel-simple driver.
The now obsolete 'display-timings' node is kept for compatibility with
U-Boot, which derives its display configuration therefrom.
Lothar Waßmann [Tue, 24 Oct 2017 13:18:34 +0000 (15:18 +0200)]
ARM: dts: imx6ul: add support for TXUL-8013
The TXUL-8013 is a Computer On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6ULL MCIMX6Y2, 528 MHz
RAM 256MB 16-bit DDR3 SDRAM
ROM 4GB eMMC
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 85°C
Under certain circumstances the ethernet PHY cannot be detected on
Ka-Ro electronics TXUL modules. Using a phy-reset-post-delay of > 5ms
alleviates this problem. Specify a value of 10ms to be on the safe side.
Lothar Waßmann [Tue, 24 Oct 2017 13:16:17 +0000 (15:16 +0200)]
ARM: dts: imx: add support for TX6QP
The TX6QP-8037 is a Computer On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6QuadPlus MCIMX6QP7, 1 GHz
RAM 1GiB 64-bit DDR3 SDRAM
ROM 4GB HiRel eMMC
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 105°C
Under certain circumstances the ethernet PHY cannot be detected on
Ka-Ro electronics TX6 modules. Using a phy-reset-post-delay of at least
2ms alleviates this problem. Define it to 10ms to be on the safe side.
Lothar Waßmann [Tue, 24 Oct 2017 13:00:27 +0000 (15:00 +0200)]
ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
Remove the PHY INT and RESET pins from hog section and put them into
their own pinctrl nodes referenced by the appropriate driver nodes.
Also, the MDIO pins are required for probing the Ethernet PHY, so they
must be configured by the FEC driver, not by the PHY driver. Move the
corresponding pinctrl settings from the PHY subnode to the FEC node.
Lothar Waßmann [Tue, 24 Oct 2017 12:59:33 +0000 (14:59 +0200)]
ARM: dts: imx6-tx6: update model property to match current module HW revision
The current TX6Q module HW revision is 3 reflected in the module name
suffix '-1030' (-1130 for LVDS).
Change the model string to prevent confusion about what DTS file to
use for these modules.
Lothar Waßmann [Wed, 11 Oct 2017 10:15:43 +0000 (12:15 +0200)]
backlight: pwm_bl: add configurable delay between re-enabling PWM and switching backlight power on
When switching the backlight on, the LCD may need some time to adjust
to the configured PWM duty cycle. Add a configurable delay between
configuring the PWM and enabling the backlight regulator to account
for this.
Lothar Waßmann [Wed, 11 Oct 2017 08:07:19 +0000 (10:07 +0200)]
ARM: dts: imx53-tx53: add support for I2C bus recovery
The imx-i2c driver supports automatic bus recovery via the GPIO
function of the I2C pins. Enable this functionality for the Ka-Ro
electronics TX53 modules.
Lothar Waßmann [Wed, 11 Oct 2017 08:07:09 +0000 (10:07 +0200)]
ARM: dts: imx53-tx53: use explicit pad_ctl settings for I2C pins
Don't rely on the padctl settings established by the boot loader, but
explicitly specify the padctl values in DTB. This is also necessary to
be able to use the DTB files from the Linux kernel for future U-Boot
versions that support HW configuration via DTB.
Lothar Waßmann [Tue, 10 Oct 2017 16:32:58 +0000 (18:32 +0200)]
drm/panel: simple: add support for EDT ET1010G0DSA/ETML1010G0DKA 10.1" WXGA LVDS panels
This adds support for the Emerging Display Technologies Corporation
10.1" WXGA LVDS panel ET1010G0DSA (without a touch panel) and
ETML1010G0DKA (with capacitive touch panel).
Lothar Waßmann [Tue, 10 Oct 2017 12:01:20 +0000 (14:01 +0200)]
net: fec: don't skip check of num-rx-queues, when num-tx-queues is out of range
There is no need to return from fec_enet_get_queue_num(), skipping the
check for num-rx-queues, when the value of num-tx-queues specified in
DT is invalid.
Furthermore print the name of the DT property set by the user, rather
than the driver's internal variable name in the warning message.
drm/panel: simple: add support for overriding the pixel clock polarity
The Ka-Ro electronics MB7 baseboard has an on-board LCD->LVDS
converter that requires a fixed pixelclk polarity, no matter what the
panel's display_mode specifies. Add an option to override the pixelclk
polarity defined in the panel's display_mode via DTB.
drm/panel: simple: make it possible to override LCD bus format
The baseboards for the Ka-Ro electronics series of i.MX modules have
their display ports wired to the topmost bits of the R,G,B bit
lanes. Thus no matter what LCD bus width (18 or 24bit) a module
provides, the LCD port can be used without shuffling bit lanes.
Add a function to handle certain quirks of the LCD interface to the
panel driver to be able to override the bus format specified in a
panel's display_mode.
drm/panel: simple: simplify display_mode definitions by using macro
Use the newly defined macro to generate the display_mode data entries
for all panels. This reduces the code size significantly and makes the
code more readable.
drm/panel: simple: add a macro for defining display modes in a simpler and less error prone way
Create a macro that eases the definition of display mode parameters by
accecpting the parameters:
freq, hactive, hfront-porch, hsynclen, hback-porch,
vactive, vfront-porch, vsynclen, vback-porch, vrefresh
that can be usually directly taken from an LCD datasheet.
Put the calculations that are now open coded repeating the same
parameters multiple times into the macro expansion.
backlight: pwm_bl: Enable PWM before switching regulator on
When the PWM is re-enabled after being switched off, the backlight may
flicker due to the backlight power being switched on while the PWM is
still unconfigured. This is especially true if the PWM output is
active low (assuming that the PWM output is low when the PWM is not
enabled).
Configure the PWM before switching backlight power on to prevent this.
Lothar Waßmann [Tue, 29 Aug 2017 10:07:00 +0000 (12:07 +0200)]
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
chip->bits_per_cell which is used to determine the NAND cell type
(SLC/MLC) should always have a value != 0.
Complain loudly if the value is 0 in nand_is_slc() to catch use before
correct initialization.
Lothar Waßmann [Tue, 29 Aug 2017 10:06:47 +0000 (12:06 +0200)]
mtd: nand: make Samsung SLC NAND usable again
commit c51d0ac59f24 ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before interpreting the ID bytes retrieved
from the chip. With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function is called. This is interpreted by nand_is_slc() as
an indicator for an MLC chip (bits_per_cell != 1).
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"The two indirect syscall fixes have sat in linux-next for a few days.
I did check back with a hardware designer to ensure a SYNC is really
what's required for the GIC fix and so the GIC fix didn't make it into
to linux-next in time for this final pull request.
It builds in local build tests and passes Imagination's test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
irqchip: mips-gic: SYNC after enabling GIC region
MIPS: Remove pt_regs adjustments in indirect syscall handler
MIPS: seccomp: Fix indirect syscall args
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Expand the space for uncompressing as the LZ4 worst case does not fit
into the currently reserved space
- Validate boot parameters more strictly to prevent out of bound access
in the decompressor/boot code
- Fix off by one errors in get_segment_base()
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Prevent faulty bootparams.screeninfo from causing harm
x86/boot: Provide more slack space during decompression
x86/ldt: Fix off by one in get_segment_base()
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for a thinko in the raw timekeeper update which causes
clock MONOTONIC_RAW to run with erratically increased frequency"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Fix ktime_get_raw() incorrect base accumulation
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs version warning fix from Steve French:
"As requested, additional kernel warning messages to clarify the
default dialect changes"
[ There is still some discussion about exactly which version should be
the new default. Longer-term we have auto-negotiation coming, but
that's not there yet.. - Linus ]
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
Fix warning messages when mounting to older servers
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of late-arriving fixes before final 4.13:
- A few reverts of DT bindings on Allwinner for their ethernet
driver. Discussion didn't converge, and since bindings are
considered ABI it makes sense to revert instead of having to
support two bindings long-term.
- A fix to enumerate GPIOs properly on Marvell Armada AP806"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The ismt driver had a problem with a rarely used transaction type and
the designware driver was made even more robust against non standard
ACPI tables"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Round down ACPI provided clk to nearest supported clk
i2c: ismt: Return EMSGSIZE for block reads with bogus length
i2c: ismt: Don't duplicate the receive length for block reads
epoll: fix race between ep_poll_callback(POLLFREE) and ep_free()/ep_remove()
The race was introduced by me in commit 971316f0503a ("epoll:
ep_unregister_pollwait() can use the freed pwq->whead"). I did not
realize that nothing can protect eventpoll after ep_poll_callback() sets
->whead = NULL, only whead->lock can save us from the race with
ep_free() or ep_remove().
Move ->whead = NULL to the end of ep_poll_callback() and add the
necessary barriers.
TODO: cleanup the ewake/EPOLLEXCLUSIVE logic, it was confusing even
before this patch.
Hopefully this explains use-after-free reported by syzcaller:
BUG: KASAN: use-after-free in debug_spin_lock_before
...
_raw_spin_lock_irqsave+0x4a/0x60 kernel/locking/spinlock.c:159
ep_poll_callback+0x29f/0xff0 fs/eventpoll.c:1148
this is spin_lock(eventpoll->lock),
...
Freed by task 17774:
...
kfree+0xe8/0x2c0 mm/slub.c:3883
ep_free+0x22c/0x2a0 fs/eventpoll.c:865
Fixes: 971316f0503a ("epoll: ep_unregister_pollwait() can use the freed pwq->whead") Reported-by: 范龙飞 <long7573@126.com> Cc: stable@vger.kernel.org Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Fix handling of pinned BPF map nodes in hash of maps, from Daniel
Borkmann.
2) IPSEC ESP error paths leak memory, from Steffen Klassert.
3) We need an RCU grace period before freeing fib6_node objects, from
Wei Wang.
4) Must check skb_put_padto() return value in HSR driver, from FLorian
Fainelli.
5) Fix oops on PHY probe failure in ftgmac100 driver, from Andrew
Jeffery.
6) Fix infinite loop in UDP queue when using SO_PEEK_OFF, from Eric
Dumazet.
7) Use after free when tcf_chain_destroy() called multiple times, from
Jiri Pirko.
8) Fix KSZ DSA tag layer multiple free of SKBS, from Florian Fainelli.
9) Fix leak of uninitialized memory in sctp_get_sctp_info(),
inet_diag_msg_sctpladdrs_fill() and inet_diag_msg_sctpaddrs_fill().
From Stefano Brivio.
10) L2TP tunnel refcount fixes from Guillaume Nault.
11) Don't leak UDP secpath in udp_set_dev_scratch(), from Yossi
Kauperman.
12) Revert a PHY layer change wrt. handling of PHY_HALTED state in
phy_stop_machine(), it causes regressions for multiple people. From
Florian Fainelli.
13) When packets are sent out of br0 we have to clear the
offload_fwdq_mark value.
14) Several NULL pointer deref fixes in packet schedulers when their
->init() routine fails. From Nikolay Aleksandrov.
15) Aquantium devices cannot checksum offload correctly when the packet
is <= 60 bytes. From Pavel Belous.
16) Fix vnet header access past end of buffer in AF_PACKET, from
Benjamin Poirier.
17) Double free in probe error paths of nfp driver, from Dan Carpenter.
18) QOS capability not checked properly in DCB init paths of mlx5
driver, from Huy Nguyen.
19) Fix conflicts between firmware load failure and health_care timer in
mlx5, also from Huy Nguyen.
20) Fix dangling page pointer when DMA mapping errors occur in mlx5,
from Eran Ben ELisha.
21) ->ndo_setup_tc() in bnxt_en driver doesn't count rings properly,
from Michael Chan.
22) Missing MSIX vector free in bnxt_en, also from Michael Chan.
23) Refcount leak in xfrm layer when using sk_policy, from Lorenzo
Colitti.
24) Fix copy of uninitialized data in qlge driver, from Arnd Bergmann.
25) bpf_setsockopts() erroneously always returns -EINVAL even on
success. Fix from Yuchung Cheng.
26) tipc_rcv() needs to linearize the SKB before parsing the inner
headers, from Parthasarathy Bhuvaragan.
27) Fix deadlock between link status updates and link removal in netvsc
driver, from Stephen Hemminger.
28) Missed locking of page fragment handling in ESP output, from Steffen
Klassert.
29) Fix refcnt leak in ebpf congestion control code, from Sabrina
Dubroca.
30) sxgbe_probe_config_dt() doesn't check devm_kzalloc()'s return value,
from Christophe Jaillet.
31) Fix missing ipv6 rx_dst_cookie update when rx_dst is updated during
early demux, from Paolo Abeni.
32) Several info leaks in xfrm_user layer, from Mathias Krause.
33) Fix out of bounds read in cxgb4 driver, from Stefano Brivio.
34) Properly propagate obsolete state of route upwards in ipv6 so that
upper holders like xfrm can see it. From Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (118 commits)
udp: fix secpath leak
bridge: switchdev: Clear forward mark when transmitting packet
mlxsw: spectrum: Forbid linking to devices that have uppers
wl1251: add a missing spin_lock_init()
Revert "net: phy: Correctly process PHY_HALTED in phy_stop_machine()"
net: dsa: bcm_sf2: Fix number of CFP entries for BCM7278
kcm: do not attach PF_KCM sockets to avoid deadlock
sch_tbf: fix two null pointer dereferences on init failure
sch_sfq: fix null pointer dereference on init failure
sch_netem: avoid null pointer deref on init failure
sch_fq_codel: avoid double free on init failure
sch_cbq: fix null pointer dereferences on init failure
sch_hfsc: fix null pointer deref and double free on init failure
sch_hhf: fix null pointer dereference on init failure
sch_multiq: fix double free on init failure
sch_htb: fix crash on init failure
net/mlx5e: Fix CQ moderation mode not set properly
net/mlx5e: Fix inline header size for small packets
net/mlx5: E-Switch, Unload the representors in the correct order
net/mlx5e: Properly resolve TC offloaded ipv6 vxlan tunnel source address
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple drivers fixes (Synaptics PS/2, Xpad)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - fix PowerA init quirk for some gamepad models
Input: synaptics - fix device info appearing different on reconnect
Merge tag 'sound-4.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Three regression fixes that should be addressed before the final
release: a missing mutex call in OSS PCM emulation ioctl, ASoC rt5670
headset detection breakage, and a regression in simple-card parser
code"
* tag 'sound-4.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: simple_card_utils: fix fallback when "label" property isn't present
ALSA: pcm: Fix power lock unbalance via OSS emulation
ASoC: rt5670: Fix GPIO headset detection regression
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Three more bug fixes for v4.13.
The two memory management related fixes are quite new, they fix kernel
crashes that can be triggered by user space.
The third commit fixes a bug in the vfio ccw translation code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix BUG_ON in crst_table_upgrade
s390/mm: fork vs. 5 level page tabel
vfio: ccw: fix bad ptr math for TIC cda translation
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Regression in chacha20 handling of chunked input
- Crash in algif_skcipher when used with async io
- Potential bogus pointer dereference in lib/mpi"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_skcipher - only call put_page on referenced and used pages
crypto: testmgr - add chunked test cases for chacha20
crypto: chacha20 - fix handling of chunked input
lib/mpi: kunmap after finishing accessing buffer
After commit dce4551cb2ad ("udp: preserve head state for IP_CMSG_PASSSEC")
we preserve the secpath for the whole skb lifecycle, but we also
end up leaking a reference to it.
We must clear the head state on skb reception, if secpath is
present.
Fixes: dce4551cb2ad ("udp: preserve head state for IP_CMSG_PASSSEC") Signed-off-by: Yossi Kuperman <yossiku@mellanox.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: switchdev: Clear forward mark when transmitting packet
Commit 6bc506b4fb06 ("bridge: switchdev: Add forward mark support for
stacked devices") added the 'offload_fwd_mark' bit to the skb in order
to allow drivers to indicate to the bridge driver that they already
forwarded the packet in L2.
In case the bit is set, before transmitting the packet from each port,
the port's mark is compared with the mark stored in the skb's control
block. If both marks are equal, we know the packet arrived from a switch
device that already forwarded the packet and it's not re-transmitted.
However, if the packet is transmitted from the bridge device itself
(e.g., br0), we should clear the 'offload_fwd_mark' bit as the mark
stored in the skb's control block isn't valid.
This scenario can happen in rare cases where a packet was trapped during
L3 forwarding and forwarded by the kernel to a bridge device.
Fixes: 6bc506b4fb06 ("bridge: switchdev: Add forward mark support for stacked devices") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Yotam Gigi <yotamg@mellanox.com> Tested-by: Yotam Gigi <yotamg@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Forbid linking to devices that have uppers
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Nogah Frankel <nogahf@mellanox.com> Tested-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steve French [Fri, 1 Sep 2017 02:34:24 +0000 (21:34 -0500)]
Fix warning messages when mounting to older servers
When mounting to older servers, such as Windows XP (or even Windows 7),
the limited error messages that can be passed back to user space can
get confusing since the default dialect has changed from SMB1 (CIFS) to
more secure SMB3 dialect. Log additional information when the user chooses
to use the default dialects and when the server does not support the
dialect requested.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Merge tag 'cifs-fixes-for-4.13-rc7-and-stable' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two cifs bug fixes for stable"
* tag 'cifs-fixes-for-4.13-rc7-and-stable' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: remove endian related sparse warning
CIFS: Fix maximum SMB2 header size
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Unfortunately a few issues that warrant sending another pull request,
even if I had hoped to avoid it. This contains:
- A fix for multiqueue xen-blkback, on tear down / disconnect.
- A few fixups for NVMe, including a wrong bit definition, fix for
host memory buffers, and an nvme rdma page size fix"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix the definition of the doorbell buffer config support bit
nvme-pci: use dma memory for the host memory buffer descriptors
nvme-rdma: default MR page size to 4k
xen-blkback: stop blkback thread of every queue in xen_blkif_disconnect
Merge tag 'for-4.13/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- A couple fixes for bugs introduced as part of the blk_status_t block
layer changes during the 4.13 merge window
- A printk throttling fix to use discrete rate limiting state for each
DM log level
- A stable@ fix for DM multipath that delays request requeueing to
avoid CPU lockup if/when the request queue is "dying"
* tag 'for-4.13/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: do not lock up a CPU with requeuing activity
dm: fix printk() rate limiting code
dm mpath: retry BLK_STS_RESOURCE errors
dm: fix the second dec_pending() argument in __split_and_process_bio()
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
scripts/dtc: fix '%zx' warning
include/linux/compiler.h: don't perform compiletime_assert with -O0
mm, madvise: ensure poisoned pages are removed from per-cpu lists
mm, uprobes: fix multiple free of ->uprobes_state.xol_area
kernel/kthread.c: kthread_worker: don't hog the cpu
mm,page_alloc: don't call __node_reclaim() with oom_lock held.
Merge mmu_notifier fixes from Jérôme Glisse:
"The invalidate_page callback suffered from 2 pitfalls. First it used
to happen after page table lock was release and thus a new page might
have been setup for the virtual address before the call to
invalidate_page().
This is in a weird way fixed by commit c7ab0d2fdc84 ("mm: convert
try_to_unmap_one() to use page_vma_mapped_walk()") which moved the
callback under the page table lock. Which also broke several existing
user of the mmu_notifier API that assumed they could sleep inside this
callback.
The second pitfall was invalidate_page being the only callback not
taking a range of address in respect to invalidation but was giving an
address and a page. Lot of the callback implementer assumed this could
never be THP and thus failed to invalidate the appropriate range for
THP pages.
By killing this callback we unify the mmu_notifier callback API to
always take a virtual address range as input.
There is now two clear API (I am not mentioning the youngess API which
is seldomly used):
- invalidate_range_start()/end() callback (which allow you to sleep)
- invalidate_range() where you can not sleep but happen right after
page table update under page table lock
Note that a lot of existing user feels broken in respect to
range_start/ range_end. Many user only have range_start() callback but
there is nothing preventing them to undo what was invalidated in their
range_start() callback after it returns but before any CPU page table
update take place.
The code pattern use in kvm or umem odp is an example on how to
properly avoid such race. In a nutshell use some kind of sequence
number and active range invalidation counter to block anything that
might undo what the range_start() callback did.
If you do not care about keeping fully in sync with CPU page table (ie
you can live with CPU page table pointing to new different page for a
given virtual address) then you can take a reference on the pages
inside the range_start callback and drop it in range_end or when your
driver is done with those pages.
Last alternative is to use invalidate_range() if you can do
invalidation without sleeping as invalidate_range() callback happens
under the CPU page table spinlock right after the page table is
updated.
The first two patches convert existing mmu_notifier_invalidate_page()
calls to mmu_notifier_invalidate_range() and bracket those call with
call to mmu_notifier_invalidate_range_start()/end().
The next ten patches remove existing invalidate_page() callback as it
can no longer happen.
Finally the last page remove the invalidate_page() callback completely
so it can RIP.
Changes since v1:
- remove more dead code in kvm (no testing impact)
- more accurate end address computation (patch 2) in page_mkclean_one
and try_to_unmap_one
- added tested-by/reviewed-by gotten so far"
* emailed patches from Jérôme Glisse <jglisse@redhat.com>:
mm/mmu_notifier: kill invalidate_page
KVM: update to new mmu_notifier semantic v2
xen/gntdev: update to new mmu_notifier semantic
sgi-gru: update to new mmu_notifier semantic
misc/mic/scif: update to new mmu_notifier semantic
iommu/intel: update to new mmu_notifier semantic
iommu/amd: update to new mmu_notifier semantic
IB/hfi1: update to new mmu_notifier semantic
IB/umem: update to new mmu_notifier semantic
drm/amdgpu: update to new mmu_notifier semantic
powerpc/powernv: update to new mmu_notifier semantic
mm/rmap: update to new mmu_notifier semantic v2
dax: update to new mmu_notifier semantic
Dave Kleikamp [Thu, 31 Aug 2017 21:46:59 +0000 (16:46 -0500)]
jfs should use MAX_LFS_FILESIZE when calculating s_maxbytes
jfs had previously avoided the use of MAX_LFS_FILESIZE because it hadn't
accounted for the whole 32-bit index range on 32-bit systems. That has
been fixed by commit 0cc3b0ec23ce ("Clarify (and fix) MAX_LFS_FILESIZE
macros"), so we can simplify the code now.
Suggested by Andreas Dilger.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Cc: jfs-discussion@lists.sourceforge.net Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King [Thu, 31 Aug 2017 23:15:36 +0000 (16:15 -0700)]
scripts/dtc: fix '%zx' warning
dtc uses an incorrect format specifier for printing a uint64_t value.
uint64_t may be either 'unsigned long' or 'unsigned long long' depending
on the host architecture.
Fix this by using %llx and casting to unsigned long long, which ensures
that we always have a wide enough variable to print 64 bits of hex.
HOSTCC scripts/dtc/checks.o
scripts/dtc/checks.c: In function 'check_simple_bus_reg':
scripts/dtc/checks.c:876:2: warning: format '%zx' expects argument of type 'size_t', but argument 4 has type 'uint64_t' [-Wformat=]
snprintf(unit_addr, sizeof(unit_addr), "%zx", reg);
^
scripts/dtc/checks.c:876:2: warning: format '%zx' expects argument of type 'size_t', but argument 4 has type 'uint64_t' [-Wformat=]
Link: http://lkml.kernel.org/r/20170829222034.GJ20805@n2100.armlinux.org.uk Fixes: 828d4cdd012c ("dtc: check.c fix compile error") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Cc: Rob Herring <robh+dt@kernel.org> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Shuah Khan <shuahkh@osg.samsung.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Stringer [Thu, 31 Aug 2017 23:15:33 +0000 (16:15 -0700)]
include/linux/compiler.h: don't perform compiletime_assert with -O0
Commit c7acec713d14 ("kernel.h: handle pointers to arrays better in
container_of()") made use of __compiletime_assert() from container_of()
thus increasing the usage of this macro, allowing developers to notice
type conflicts in usage of container_of() at compile time.
However, the implementation of __compiletime_assert relies on compiler
optimizations to report an error. This means that if a developer uses
"-O0" with any code that performs container_of(), the compiler will always
report an error regardless of whether there is an actual problem in the
code.
This patch disables compile_time_assert when optimizations are disabled to
allow such code to compile with CFLAGS="-O0".
Example compilation failure:
./include/linux/compiler.h:547:38: error: call to `__compiletime_assert_94' declared with attribute error: pointer type mismatch in container_of()
_compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
^
./include/linux/compiler.h:530:4: note: in definition of macro `__compiletime_assert'
prefix ## suffix(); \
^~~~~~
./include/linux/compiler.h:547:2: note: in expansion of macro `_compiletime_assert'
_compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
^~~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:46:37: note: in expansion of macro `compiletime_assert'
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^~~~~~~~~~~~~~~~~~
./include/linux/kernel.h:860:2: note: in expansion of macro `BUILD_BUG_ON_MSG'
BUILD_BUG_ON_MSG(!__same_type(*(ptr), ((type *)0)->member) && \
^~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: use do{}while(0), per Michal] Link: http://lkml.kernel.org/r/20170829230114.11662-1-joe@ovn.org Fixes: c7acec713d14c6c ("kernel.h: handle pointers to arrays better in container_of()") Signed-off-by: Joe Stringer <joe@ovn.org> Cc: Ian Abbott <abbotti@mev.co.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 31 Aug 2017 23:15:30 +0000 (16:15 -0700)]
mm, madvise: ensure poisoned pages are removed from per-cpu lists
Wendy Wang reported off-list that a RAS HWPOISON-SOFT test case failed
and bisected it to the commit 479f854a207c ("mm, page_alloc: defer
debugging checks of pages allocated from the PCP").
The problem is that a page that was poisoned with madvise() is reused.
The commit removed a check that would trigger if DEBUG_VM was enabled
but re-enabling the check only fixes the problem as a side-effect by
printing a bad_page warning and recovering.
The root of the problem is that an madvise() can leave a poisoned page
on the per-cpu list. This patch drains all per-cpu lists after pages
are poisoned so that they will not be reused. Wendy reports that the
test case in question passes with this patch applied. While this could
be done in a targeted fashion, it is over-complicated for such a rare
operation.
Eric Biggers [Thu, 31 Aug 2017 23:15:26 +0000 (16:15 -0700)]
mm, uprobes: fix multiple free of ->uprobes_state.xol_area
Commit 7c051267931a ("mm, fork: make dup_mmap wait for mmap_sem for
write killable") made it possible to kill a forking task while it is
waiting to acquire its ->mmap_sem for write, in dup_mmap().
However, it was overlooked that this introduced an new error path before
the new mm_struct's ->uprobes_state.xol_area has been set to NULL after
being copied from the old mm_struct by the memcpy in dup_mm(). For a
task that has previously hit a uprobe tracepoint, this resulted in the
'struct xol_area' being freed multiple times if the task was killed at
just the right time while forking.
Fix it by setting ->uprobes_state.xol_area to NULL in mm_init() rather
than in uprobe_dup_mmap().
With CONFIG_UPROBE_EVENTS=y, the bug can be reproduced by the same C
program given by commit 2b7e8665b4ff ("fork: fix incorrect fput of
->exe_file causing use-after-free"), provided that a uprobe tracepoint
has been set on the fork_thread() function. For example:
Shaohua Li [Thu, 31 Aug 2017 23:15:23 +0000 (16:15 -0700)]
kernel/kthread.c: kthread_worker: don't hog the cpu
If the worker thread continues getting work, it will hog the cpu and rcu
stall complains. Make it a good citizen. This is triggered in a loop
block device test.
Link: http://lkml.kernel.org/r/5de0a179b3184e1a2183fc503448b0269f24d75b.1503697127.git.shli@fb.com Signed-off-by: Shaohua Li <shli@fb.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tejun Heo <tj@kernel.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa [Thu, 31 Aug 2017 23:15:20 +0000 (16:15 -0700)]
mm,page_alloc: don't call __node_reclaim() with oom_lock held.
We are doing a last second memory allocation attempt before calling
out_of_memory(). But since slab shrinker functions might indirectly
wait for other thread's __GFP_DIRECT_RECLAIM && !__GFP_NORETRY memory
allocations via sleeping locks, calling slab shrinker functions from
node_reclaim() from get_page_from_freelist() with oom_lock held has
possibility of deadlock. Therefore, make sure that last second memory
allocation attempt does not call slab shrinker functions.
Jérôme Glisse [Thu, 31 Aug 2017 21:17:38 +0000 (17:17 -0400)]
mm/mmu_notifier: kill invalidate_page
The invalidate_page callback suffered from two pitfalls. First it used
to happen after the page table lock was release and thus a new page
might have setup before the call to invalidate_page() happened.
This is in a weird way fixed by commit c7ab0d2fdc84 ("mm: convert
try_to_unmap_one() to use page_vma_mapped_walk()") that moved the
callback under the page table lock but this also broke several existing
users of the mmu_notifier API that assumed they could sleep inside this
callback.
The second pitfall was invalidate_page() being the only callback not
taking a range of address in respect to invalidation but was giving an
address and a page. Lots of the callback implementers assumed this
could never be THP and thus failed to invalidate the appropriate range
for THP.
By killing this callback we unify the mmu_notifier callback API to
always take a virtual address range as input.
Finally this also simplifies the end user life as there is now two clear
choices:
- invalidate_range_start()/end() callback (which allow you to sleep)
- invalidate_range() where you can not sleep but happen right after
page table update under page table lock
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: Bernhard Held <berny156@gmx.de> Cc: Adam Borowski <kilobyte@angband.pl> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: axie <axie@amd.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:37 +0000 (17:17 -0400)]
KVM: update to new mmu_notifier semantic v2
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Changed since v1 (Linus Torvalds)
- remove now useless kvm_arch_mmu_notifier_invalidate_page()
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Tested-by: Mike Galbraith <efault@gmx.de> Tested-by: Adam Borowski <kilobyte@angband.pl> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: kvm@vger.kernel.org Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:36 +0000 (17:17 -0400)]
xen/gntdev: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Roger Pau Monné <roger.pau@citrix.com> Cc: xen-devel@lists.xenproject.org (moderated for non-subscribers) Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:35 +0000 (17:17 -0400)]
sgi-gru: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: Dimitri Sivanich <sivanich@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:34 +0000 (17:17 -0400)]
misc/mic/scif: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: Sudeep Dutt <sudeep.dutt@intel.com> Cc: Ashutosh Dixit <ashutosh.dixit@intel.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:33 +0000 (17:17 -0400)]
iommu/intel: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: iommu@lists.linux-foundation.org Cc: Joerg Roedel <jroedel@suse.de> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:32 +0000 (17:17 -0400)]
iommu/amd: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Jérôme Glisse [Thu, 31 Aug 2017 21:17:31 +0000 (17:17 -0400)]
IB/hfi1: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: linux-rdma@vger.kernel.org Cc: Dean Luick <dean.luick@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Doug Ledford <dledford@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:30 +0000 (17:17 -0400)]
IB/umem: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Tested-by: Leon Romanovsky <leonro@mellanox.com> Cc: linux-rdma@vger.kernel.org Cc: Artemy Kovalyov <artemyko@mellanox.com> Cc: Doug Ledford <dledford@redhat.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:29 +0000 (17:17 -0400)]
drm/amdgpu: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Reviewed-by: Christian König <christian.koenig@amd.com> Cc: amd-gfx@lists.freedesktop.org Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jérôme Glisse [Thu, 31 Aug 2017 21:17:28 +0000 (17:17 -0400)]
powerpc/powernv: update to new mmu_notifier semantic
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and now are bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: linuxppc-dev@lists.ozlabs.org Cc: Alistair Popple <alistair@popple.id.au> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>