snd_seq_oss_synth_make_info() incorrectly reports information
to userspace without first checking for the validity of the
device number, leading to possible information leak (CVE-2008-3272).
Don't forget to kill tasklets on stop to not panic if they
fire after freeing some structures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When signal is noisy, hardware can use all RX buffers and since the last
entry in the list is self-linked, it overwrites the entry until we link
new buffers.
Ensure that we don't free this last one until we are 100% sure that it
is not used by the hardware anymore to not cause memory curruption as
can be seen below.
This is done by checking next buffer in the list. Even after that we
know that the hardware refetched the new link and proceeded further
(the next buffer is ready) we can finally free the overwritten buffer.
We discard it since the status in its descriptor is overwritten (OR-ed
by new status) too.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lookup can install a child dentry for a deleted directory. This keeps
the directory dentry alive, and the inode pinned in the cache and on
disk, even after all external references have gone away.
This isn't a big problem normally, since memory pressure or umount
will clear out the directory dentry and its children, releasing the
inode. But for UBIFS this causes problems because its orphan area can
overflow.
Fix this by returning ENOENT for all lookups on a S_DEAD directory
before creating a child dentry.
Thanks to Zoltan Sogor for noticing this while testing UBIFS, and
Artem for the excellent analysis of the problem and testing.
Many HD-audio controllers seem inaccurate about the IRQ timing of
PCM period updates. This has caused problems on audio quality; e.g.
JACK doesn't work with two periods.
This patch fixes the problem by checking the current DMA position
at IRQ handler and delays the period-update via a workq if it's
inaccurate.
Don't create mixer volume elements for Headphone and Speaker if they
use the same DAC as normal line-outs on AD1988. Otherwise the amp
value gets screwed up, e.g.
https://bugzilla.novell.com/show_bug.cgi?id=398255
Current versions of gdb require a working implementation of
PTRACE_GETSIGINFO for proper watchpoint support. Since struct siginfo
contains pointers it must be converted when passed to a 32-bit debugger.
Signed-off-by: Andreas Schwab <schwab@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the HIDP or BNEP kernel support, the user-space needs to
know if the connection has been terminated for some reasons. Wake up
the application if that happens. Otherwise kernel and user-space are
no longer on the same page and weird behaviors can happen.
This patch introduces i8042_dmi_nopnp_table to make it possible to perform
DMI matches for systems that need 'i8042.nopnp' to work correctly, and
introduces such an entry for Intel D845PESV -- this system doesn't
detect PS2 mouse reliably without this option, as reported by Robert
Lewis.
[dtor@mail.ru - make it compile if CONFIG_PNP is off - reported
by Randy Dunlap]
journal_try_to_free_buffers() could race with jbd commit transaction when
the later is holding the buffer reference while waiting for the data
buffer to flush to disk. If the caller of journal_try_to_free_buffers()
request tries hard to release the buffers, it will treat the failure as
error and return back to the caller. We have seen the directo IO failed
due to this race. Some of the caller of releasepage() also expecting the
buffer to be dropped when passed with GFP_KERNEL mask to the
releasepage()->journal_try_to_free_buffers().
With this patch, if the caller is passing the __GFP_WAIT and __GFP_FS to
indicating this call could wait, in case of try_to_free_buffers() failed,
let's waiting for journal_commit_transaction() to finish commit the
current committing transaction, then try to free those buffers again.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Mingming Cao <cmm@us.ibm.com> Reviewed-by: Badari Pulavarty <pbadari@us.ibm.com> Acked-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata(). It fixes the problem in all of the scsi
drivers that need it.
Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The problem is ch_probe stores ch's private data at a wrong place.
We need to store it at scsi_device->sdev_gendev but the above patch
stores it at device struct that device_create_drvdata returns. So we
hit an oops when ch_remove accesses
scsi_device->sdev_gendev->driver_data, which is NULL.
Actually, there wasn't a race because ch doesn't create sysfs files
with device struct that device_create returns. This patch puts back
dev_set_drvdata() to set ch's private data properly.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> CC: Oliver Pinter <oliver.pntr@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Mon, 2008-04-21 at 18:54 -0400, Masami Hiramatsu wrote:
> Thank you for reporting.
>
> Actually, kprobes tries to fixup thread's flags in post_kprobe_handler
> (which is called from kprobe_exceptions_notify) by
> trace_hardirqs_fixup_flags(pt_regs->flags). However, even the irq flag
> is set in pt_regs->flags, true hardirq is still off until returning
> from do_debug. Thus, lockdep assumes that hardirq is off without
annotation.
>
> IMHO, one possible solution is that fixing hardirq flags right after
> notify_die in do_debug instead of in post_kprobe_handler.
Ok, do_debug() is a trap, this can happen at any time regardless of the
machine's IRQ state. So the first thing we do is fix up the IRQ state.
Then we call this die notifier stuff; and return with messed up IRQ
state... YAY.
So, kprobes fudges it..
notify_die(DIE_DEBUG)
kprobe_exceptions_notify()
post_kprobe_handler()
modify regs->flags
trace_hardirqs_fixup_flags(regs->flags); <--- must be it
So what's the use of modifying flags if they're not meant to take effect
at some point.
/me tries to reproduce issue; enable kprobes test thingy && boot
OK, that reproduces..
So the below makes it work - but I'm not getting this code; at the time
I wrote that stuff I CC'ed each and every kprobe maintainer listed in
the usual places but got no reposonse - can some please explain this
stuff to me?
Are the saved flags only for the TF bit or are they made in full effect
later (and if so, where) ?
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Masami Hiramatsu <mhiramat@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> CC: Oliver Pinter <oliver.pntr@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a possible race in md_probe. If two threads call md_probe
for the same device, then one could exit (having checked that
->gendisk exists) before the other has called kobject_init_and_add,
thus returning an incomplete kobj which will cause problems when
we try to add children to it.
So extend the range of protection of disks_mutex slightly to
avoid this possibility.
Signed-off-by: Neil Brown <neilb@suse.de> CC: Oliver Pinter <oliver.pntr@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[SCSI] bsg: fix bsg_mutex hang with device removal
We don't need to hold bsg_mutex during bsg_complete_all_commands(). It
leads to a problem that we block bsg_unregister_queue during
bsg_complete_all_commands (untill all the outstanding commands
complete).
Thanks to Pete Wyckoff for finding the bug and testing the patch.
According to RFC2327, the connection information is optional
in the session description since it can be specified in the
media description instead.
My provider does exactly that and does not provide any connection
information in the session description. As a result the new
kernel drops all invite responses.
This patch makes it optional as documented.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We zero-fill them like we are supposed to, and that's all fine. It's
only an error if the 'romfs_copyfrom()' routine isn't able to fill the
data that is supposed to be there.
Most of the patch is really just re-organizing the code a bit, and using
separate variables for the error value and for how much of the page we
actually filled from the filesystem.
Reported-and-tested-by: Chris Fester <cfester@wms.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Matt Waddel <matt.waddel@freescale.com> Cc: Greg Ungerer <gerg@snapgear.com> Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iov_iter_advance() function would look at the iov->iov_len entry
even though it might have iterated over the whole array, and iov was
pointing past the end. This would cause DEBUG_PAGEALLOC to trigger a
kernel page fault if the allocation was at the end of a page, and the
next page was unallocated.
The quick fix is to just change the order of the tests: check that there
is any iovec data left before we check the iov entry itself.
Thanks to Alexey Dobriyan for finding this case, and testing the fix.
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI is a nice thing, but we cannot enable it without changing the
interrupt handler. If we do it, we break MSI capable hardware,
specifically AR5006 chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
.. when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ingo Molnar provided a fix to not call _PPC at processor driver
initialization time in "[PATCH] ACPI: fix cpufreq regression" (git
commit e4233dec749a3519069d9390561b5636a75c7579)
But it can still happen that _PPC is called at processor driver
initialization time.
This patch should make sure that this is not possible anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de> Cc: Andi Kleen <andi@firstfloor.org> Cc: Len Brown <lenb@kernel.org> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] inode-diet: Eliminate i_blksize from the inode structure
caused the block size used by pseudo-filesystems to decrease from
PAGE_SIZE to 1024 leading to a doubling of the number of context switches
during a kernbench run.
Signed-off-by: Alex Nixon <Alex.Nixon@citrix.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Ian Campbell <Ian.Campbell@eu.citrix.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hugh@veritas.com> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Paul pointed out two incorrect read barriers in the marker handler code in
the path where multiple probes are connected. Those are ordering reads of
"ptype" (single or multi probe marker), "multi" array pointer, and "multi"
array data access.
It should be ordered like this :
read ptype
smp_rmb()
read multi array pointer
smp_read_barrier_depends()
access data referenced by multi array pointer
The code with a single probe connected (optimized case, does not have to
allocate an array) has correct memory ordering.
It applies to kernel 2.6.26.x, 2.6.25.x and linux-next.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuSE's insserve initscript ordering program hits kernel BUG at mm/shmem.c:814
on 2.6.26. It's using posix_fadvise on directories, and the shmem_readpage
method added in 2.6.23 is letting POSIX_FADV_WILLNEED allocate useless pages
to a tmpfs directory, incrementing i_blocks count but never decrementing it.
Fix this by assigning shmem_aops (pointing to readpage and writepage and
set_page_dirty) only when it's needed, on a regular file or a long symlink.
Many thanks to Kel for outstanding bugreport and steps to reproduce it.
Reported-by: Kel Modderman <kel@otaku42.de> Tested-by: Kel Modderman <kel@otaku42.de> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The block transfer routine in the mpc52xx psc spi driver misinterpret
the datasheet. According to the processor datasheet the chipselect is
held as long as the EOF is not written.
Theoretically blocks of any sizes can be transferred in this way. The
old routine however writes an EOF after every word, which has the size
of size_of_word. This makes the transfer slow.
Also fixed some duplicate code.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My copying of linux/init.h didn't go far enough. The definition of
__used singled out gcc minor version 3, but didn't care what the major
version was. This broke when unit-at-a-time was added and gcc started
throwing out initcalls.
This results in an early boot crash when ptrace tries to initialize a
process with an empty, uninitialized register set.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Sandeen [Tue, 29 Jul 2008 02:50:12 +0000 (02:50 +0000)]
eCryptfs: use page_alloc not kmalloc to get a page of memory
commit 7fcba054373d5dfc43d26e243a5c9b92069972ee upstream
Date: Mon, 28 Jul 2008 15:46:39 -0700
Subject: eCryptfs: use page_alloc not kmalloc to get a page of memory
With SLUB debugging turned on in 2.6.26, I was getting memory corruption
when testing eCryptfs. The root cause turned out to be that eCryptfs was
doing kmalloc(PAGE_CACHE_SIZE); virt_to_page() and treating that as a nice
page-aligned chunk of memory. But at least with SLUB debugging on, this
is not always true, and the page we get from virt_to_page does not
necessarily match the PAGE_CACHE_SIZE worth of memory we got from kmalloc.
My simple testcase was 2 loops doing "rm -f fileX; cp /tmp/fileX ." for 2
different multi-megabyte files. With this change I no longer see the
corruption.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Acked-by: Michael Halcrow <mhalcrow@us.ibm.com> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DVB: cx23885: SRAM changes for the 885 and 887 silicon parts
In a previous patch I merged both memory maps into a single struct,
believing that they could be combined. We've since found problems
with streaming multiple channels on the 885. I'm restoring the
multiple memory map structs - in line with the windows driver.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
V4L: cx23885: Bugfix for concurrent use of /dev/video0 and /dev/video1
With the HVR1800, trying to use video0 and video1 simultaneously
caused buffer corruption in the PCIe bridge. This fix reallocates
video1 buffer locations to avoid the issue.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Copy tuner data earlier in init to avoid overwriting manual tuner type
When saa7134_board_init2 runs, it immediately overwrites the
current value (set earlier from module parameter) of tuner_type
with the static values, and then does autodetection. This patch
moves the tuner_addr copy to earlier in saa7134_initdev and
removes the tuner_type copy from saa7134_board_init2.
Autodetection could still potentially change to the wrong tuner
type, but it is now possible to override the default type for
the card again.
My card's tuner is configured with autodetection from eeprom,
so I don't need to manually set the tuner. I've checked that
the autodetection still works for my card.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de> Cc: Brian Marete <bgmarete@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UVC devices can report button events. The uvcvideo driver depends on
CONFIG_INPUT to report events to the input layer. This patch removes the hard
dependency by introducing a new CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV option.
All submitted URBs must be killed at suspend time, but URB buffers don't
have to be freed. Avoiding a free on suspend/reallocate on resume lowers
the pressure on system memory.
V4L: uvcvideo: Use GFP_NOIO when allocating memory during resume
The swap device might still be asleep, so memory allocated in the resume
handler must use GFP_NOIO. Thanks to Oliver Neukum for catching and reporting
this bug.
myri10ge: do not use mgp->max_intr_slots before loading the firmware
part of commit 0dcffac1a329be69bab0ac604bf7283737108e68 upstream
(the upstream multislice patch contains this fix within a large
rework of the code since there is one rx_done ring per slice. The
old allocating is replaced by a call to myri10ge_probe_slices())
Allocating the rx_done ring requires mgp->max_intr_slots to
be valid, which requires that we already loaded the firmware
we are going to use with this ring.
So move the allocating after myri10ge_load_firmware()
(but keep it before myri10ge_reset() which already needs the
rx_done ring).
If fixedsa regression where loading the driver would not
appear to do anything. Regression introduced in 2.6.26-rc3 by
commit 014377a1df693ff30a9e8b69f0bbb0a38e601f75
Reported and patch tested by Lukas Hejtmanek at
http://lkml.org/lkml/2008/7/22/305
Reproduced and patch tested also by me.
myri10ge: do not forget to setup the single slice pointers
part of commit 0dcffac1a329be69bab0ac604bf7283737108e68 upstream
(the upstream multislice patch contains the same fix within
myri10ge_alloc_slices() which does this for every slice)
Even if we don't have multiple slices in myri10ge in 2.6.26,
we already use some multislice-aware routines that need the
slice state pointers to mgp and dev to be valid.
This patch fixes a regression where configuring the interface up
would oops in myri10ge_allocate_rings() when using ss->mgp
(and later when using ss->dev).
Oops reported and patch tested by Lukas Hejtmanek at
http://lkml.org/lkml/2008/7/23/101
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to most
of the hotpluggable platform drivers, to re-enable auto loading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No straightforward fix exists because we want to
enable these IRQs and setup state atomically before
getting into the IRQ handler the first time.
What happens now is that we mark the VIRQ to not be
automatically enabled by request_irq(). Then we
make explicit enable_irq() calls when we grab the
LDC channel.
This way we don't need to call request_irq() illegally
under the LDC channel lock any more.
Bump LDC version and release date.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based upon an excellent bug report from Eric Dumazet.
tcp_ack() should clear ->icsk_probes_out even if there are packets
outstanding. Otherwise if we get a sequence of ACKs while we do have
packets outstanding over and over again, we'll never clear the
probes_out value and eventually think the connection is too sick and
we'll reset it.
This appears to be some "optimization" added to tcp_ack() in the 2.4.x
timeframe. In 2.2.x, probes_out is pretty much always cleared by
tcp_ack().
Here is Eric's original report:
----------------------------------------
Apparently, we can in some situations reset TCP connections in a couple of seconds when some frames are lost.
In order to reproduce the problem, please try the following program on linux-2.6.25.*
Setup some iptables rules to allow two frames per second sent on loopback interface to tcp destination port 12000
iptables -N SLOWLO
iptables -A SLOWLO -m hashlimit --hashlimit 2 --hashlimit-burst 1 --hashlimit-mode dstip --hashlimit-name slow2 -j ACCEPT
iptables -A SLOWLO -j DROP
iptables -A OUTPUT -o lo -p tcp --dport 12000 -j SLOWLO
Then run the attached program and see the output :
# ./loop
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,1)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,3)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,5)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,7)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,9)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,11)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,201ms,13)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,188ms,15)
write(): Connection timed out
wrote 890 bytes but was interrupted after 9 seconds
ESTAB 0 0 127.0.0.1:12000 127.0.0.1:54455
Exiting read() because no data available (4000 ms timeout).
read 860 bytes
While this tcp session makes progress (sending frames with 50 bytes of payload, every 500ms), linux tcp stack decides to reset it, when tcp_retries 2 is reached (default value : 15)
tcpdump :
15:30:28.856695 IP 127.0.0.1.56554 > 127.0.0.1.12000: S 33788768:33788768(0) win 32792 <mss 16396,nop,nop,sackOK,nop,wscale 7>
15:30:28.856711 IP 127.0.0.1.12000 > 127.0.0.1.56554: S 33899253:33899253(0) ack 33788769 win 32792 <mss 16396,nop,nop,sackOK,nop,wscale 7>
15:30:29.356947 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 1:61(60) ack 1 win 257
15:30:29.356966 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 61 win 257
15:30:29.866415 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 61:111(50) ack 1 win 257
15:30:29.866427 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 111 win 257
15:30:30.366516 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 111:161(50) ack 1 win 257
15:30:30.366527 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 161 win 257
15:30:30.876196 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 161:211(50) ack 1 win 257
15:30:30.876207 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 211 win 257
15:30:31.376282 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 211:261(50) ack 1 win 257
15:30:31.376290 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 261 win 257
15:30:31.885619 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 261:311(50) ack 1 win 257
15:30:31.885631 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 311 win 257
15:30:32.385705 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 311:361(50) ack 1 win 257
15:30:32.385715 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 361 win 257
15:30:32.895249 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 361:411(50) ack 1 win 257
15:30:32.895266 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 411 win 257
15:30:33.395341 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 411:461(50) ack 1 win 257
15:30:33.395351 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 461 win 257
15:30:33.918085 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 461:511(50) ack 1 win 257
15:30:33.918096 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 511 win 257
15:30:34.418163 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 511:561(50) ack 1 win 257
15:30:34.418172 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 561 win 257
15:30:34.927685 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 561:611(50) ack 1 win 257
15:30:34.927698 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 611 win 257
15:30:35.427757 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 611:661(50) ack 1 win 257
15:30:35.427766 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 661 win 257
15:30:35.937359 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 661:711(50) ack 1 win 257
15:30:35.937376 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 711 win 257
15:30:36.437451 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 711:761(50) ack 1 win 257
15:30:36.437464 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 761 win 257
15:30:36.947022 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 761:811(50) ack 1 win 257
15:30:36.947039 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 811 win 257
15:30:37.447135 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 811:861(50) ack 1 win 257
15:30:37.447203 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 861 win 257
15:30:41.448171 IP 127.0.0.1.12000 > 127.0.0.1.56554: F 1:1(0) ack 861 win 257
15:30:41.448189 IP 127.0.0.1.56554 > 127.0.0.1.12000: R 33789629:33789629(0) win 0
Source of program :
/*
* small producer/consumer program.
* setup a listener on 127.0.0.1:12000
* Forks a child
* child connect to 127.0.0.1, and sends 10 bytes on this tcp socket every 100 ms
* Father accepts connection, and read all data
*/
#include <sys/types.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <unistd.h>
#include <stdio.h>
#include <time.h>
#include <sys/poll.h>
int port = 12000;
char buffer[4096];
int main(int argc, char *argv[])
{
int lfd = socket(AF_INET, SOCK_STREAM, 0);
struct sockaddr_in socket_address;
time_t t0, t1;
int on = 1, sfd, res;
unsigned long total = 0;
socklen_t alen = sizeof(socket_address);
pid_t pid;
arm's fls() is implemented as a macro, causing it to misbehave when passed
64-bit arguments. Fix.
Cc: Nickolay Vinogradov <nickolay@protei.ru> Tested-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the addition of __attribute__((__cold__)) to a few symbols
without adjusting the linker scripts, those symbols currently may end
up outside the [_stext,_etext) range, as they get placed in
.text.unlikely by (at least) gcc 4.3.0. This may confuse code not only
outside of the kernel, symbol_put_addr()'s BUG() could also trigger.
Hence we need to add .text.unlikely (and for future uses of
__attribute__((__hot__)) also .text.hot) to the TEXT_TEXT() macro.
Issue observed by Lukas Lipavsky.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Tested-by: Lukas Lipavsky <llipavsky@suse.cz> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-at91rm9200 by scrubbing old IRQ status
before enabling IRQs.
It also removes nonfunctional periodic IRQ support from this driver;
only update IRQs are reported, or provided by the hardware.
I suspect some other RTCs probably have versions of #11112; it's easy to
overlook, since most non-RTC drivers don't care about spurious IRQs:
they're not reported to userspace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Report-by: W Unruh <unruh@physics.ubc.ca> Cc: Andrew Victor <avictor.za@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
currently if you use PTRACE_SINGLEBLOCK on AMD K6-3 (i586) it will crash.
Kernel now wrongly assumes existing DEBUGCTLMSR MSR register there.
Removed the assumption also for some other non-K6 CPUs but I am not sure there
(but it can only bring small inefficiency there if my assumption is wrong).
Based on info from Roland McGrath, Chuck Ebbert and Mikulas Patocka.
More info at:
https://bugzilla.redhat.com/show_bug.cgi?id=456175
When a kernel was rebuilt, the previous Module.markers was not cleared.
It caused markers with different format strings to appear as duplicates
when a markers was changed. This problem is present since
scripts/mod/modpost.c started to generate Module.markers, commit b2e3e658b344c6bcfb8fb694100ab2f2b5b2edb0
It therefore applies to 2.6.25, 2.6.26 and linux-next.
I merely merged the patches from Roland, Wenji and Takashi here.
Credits to
Roland McGrath <roland@redhat.com>
Wenji Huang <wenji.huang@oracle.com>
and
Takashi Nishiie <t-nishiie@np.css.fujitsu.com>
for providing the individual fixes.
- Changelog :
- Integrated Takashi's Makefile modification to clear Module.markers upon
make clean.
The explanation for recent video BIOS suspend quirk failures is that
the VESA BIOS expects to be entered in Big Real Mode (*.limit = 0xffffffff)
instead of ordinary Real Mode (*.limit = 0xffff).
This patch changes the segment descriptors to Big Real Mode instead.
The segment descriptor registers (what Intel calls "segment cache") is
always active. The only thing that changes based on CR0.PE is how it is
*loaded* and the interpretation of the CS flags.
The segment descriptor registers contain of the following sub-registers:
selector (the "visible" part), base, limit and flags. In protected mode
or long mode, they are loaded from descriptors (or fs.base or gs.base can
be manipulated directly in long mode.) In real mode, the only thing
changed by a segment register load is the selector and the base, where the
base <- selector << 4. In particular, *the limit and the flags are not
changed*.
As far as the handling of the CS flags: a code segment cannot be writable
in protected mode, whereas it is "just another segment" in real mode, so
there is some kind of quirk that kicks in for this when CR0.PE <- 0. I'm
not sure if this is accomplished by actually changing the cs.flags register
or just changing the interpretation; it might be something that is
CPU-specific. In particular, the Transmeta CPUs had an explicit "CS is
writable if you're in real mode" override, so even if you had loaded CS
with an execute-only segment it'd be writable (but not readable!) on return
to real mode. I'm not at all sure if that is how other CPUs behave.
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
usb serial decrements the pm counter even if an interface has been
disconnected. If it was a logical disconnect the interface may belong
already to another driver. This patch introduces a check for disconnected
interfaces.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Dick Streefland who provided an useful testcase on
http://lkml.org/lkml/2008/3/17/205 (only applicable to 2.6.24.x), that
helped a lot as a deterministic way to bisect an issue that leaded to
this fix.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Cc: Roland McGrath <roland@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The comment was correct -- need to make the code match the comment.
Without this patch, if a CPU goes dynticks idle (and stays there forever)
in just the right phase of preemptible-RCU grace-period processing,
grace periods stall. The offending sequence of events (courtesy
of Promela/spin, at least after I got the liveness criterion coded
correctly...) is as follows:
o CPU 0 is in dynticks-idle mode. Its dynticks_progress_counter
is (say) 10.
o CPU 0 takes an interrupt, so rcu_irq_enter() increments CPU 0's
dynticks_progress_counter to 11.
o CPU 1 is doing RCU grace-period processing in rcu_try_flip_idle(),
sees rcu_pending(), so invokes dyntick_save_progress_counter(),
which in turn takes a snapshot of CPU 0's dynticks_progress_counter
into CPU 0's rcu_dyntick_snapshot -- now set to 11. CPU 1 then
updates the RCU grace-period state to rcu_try_flip_waitack().
o CPU 0 returns from its interrupt, so rcu_irq_exit() increments
CPU 0's dynticks_progress_counter to 12.
o CPU 1 later invokes rcu_try_flip_waitack(), which notices that
CPU 0 has not yet responded, and hence in turn invokes
rcu_try_flip_waitack_needed(). This function examines the
state of CPU 0's dynticks_progress_counter and rcu_dyntick_snapshot
variables, which it copies to curr (== 12) and snap (== 11),
respectively.
Because curr!=snap, the first condition fails.
Because curr-snap is only 1 and snap is odd, the second
condition fails.
rcu_try_flip_waitack_needed() therefore incorrectly concludes
that it must wait for CPU 0 to explicitly acknowledge the
counter flip.
o CPU 0 remains forever in dynticks-idle mode, never taking
any more hardware interrupts or any NMIs, and never running
any more tasks. (Of course, -something- will usually eventually
happen, which might be why we haven't seen this one in the
wild. Still should be fixed!)
Therefore the grace period never ends. Fix is to make the code match
the comment, as shown below. With this fix, the above scenario
would be satisfied with curr being even, and allow the grace period
to proceed.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Josh Triplett <josh@kernel.org> Cc: Dipankar Sarma <dipankar@in.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ptrace has always returned only -EIO for all failures to access
registers. The user_regset calls are allowed to return a more
meaningful variety of errors. The REGSET_XFP calls use -ENODEV
for !cpu_has_fxsr hardware. Make ptrace return the traditional
-EIO instead of the error code from the user_regset call.
The direct mapped shadow code (used for real mode and two dimensional paging)
sets upper-level ptes using direct assignment rather than calling
set_shadow_pte(). A nonpae host will split this into two writes, which opens
up a race if another vcpu accesses the same memory area.
Fix by calling set_shadow_pte() instead of assigning directly.
Noticed by Izik Eidus.
Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes issue encountered with HLT instruction
under FreeDOS's HIMEM XMS Driver.
The HLT instruction jumped directly to the done label and
skips updating the EIP value, therefore causing the guest
to spin endlessly on the same instruction.
The patch changes the instruction so that it writes back
the updated EIP value.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com> Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a potention issue caused by kvm_mmu_slot_remove_write_access(). The
old behavior don't sync EPT TLB with modified EPT entry, which result
in inconsistent content of EPT TLB and EPT table.
Signed-off-by: Sheng Yang <sheng.yang@intel.com> Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On suspend the svm_hardware_disable function is called which frees all svm_data
variables. On resume they are not re-allocated. This patch removes the
deallocation of svm_data from the hardware_disable function to the
hardware_unsetup function which is not called on suspend.
The function ept_update_paging_mode_cr0() write to
CPU_BASED_VM_EXEC_CONTROL based on vmcs_config.cpu_based_exec_ctrl. That's
wrong because the variable may not consistent with the content in the
CPU_BASE_VM_EXEC_CONTROL MSR.
Signed-off-by: Sheng Yang <sheng.yang@intel.com> Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some iso9660 images contain files with rockridge data that is either
incorrect or incompletely parsed. Prior to commit f2966632a134e865db3c819346a1dc7d96e05309 ("[PATCH] rock: handle directory
overflows") (included with kernel 2.6.13) the kernel ignored the rockridge
data for these files, while still allowing the files to be accessed under
their non-rockridge names. That commit inadvertently changed things so
that files with invalid rockridge data could not be accessed at all. (I
ran across the problem when comparing some old CDs with hard disk copies I
had made long ago under kernel 2.4: a few of the files on the hard disk
copies were no longer visible on the CDs.)
This change reverts to the pre-2.6.13 behavior.
Signed-off-by: Adam Greenblatt <adam.greenblatt@gmail.com> Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When quota structure is going to be dropped and it is dirty, quota code tries
to write it. If the write fails for some reason (e. g. transaction cannot
be started because the journal is aborted), we try writing again and again and
again... Fix the problem by clearing the dirty bit even if the write failed.
(akpm: for 2.6.27, 2.6.26.x and 2.6.25.x)
Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: dingdinghua <dingdinghua85@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a trivial patch against the hdlcdrv module that fixes its CRC
calculation. The finished CRC was overwriting the first two bytes of
each packet rather than being appended to the end.
I've tested this with 2.6.8 and 2.6.10-rc1, but hdlcdrv hasn't changed
much recently so it should work with many other kernel versions.
Signed-off-by: Micah Dowty <micah@navi.cx> Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the bridge reference count problem and cleanups ipv6 FIB
timer management. Don't use expires field, because it is not a proper
way to test, instead use timer_pending().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch clamps the cscov setsockopt values to a maximum of 0xFFFF.
Setsockopt values greater than 0xffff can cause an unwanted
wrap-around. Further, IPv6 jumbograms are not supported (RFC 3838,
3.5), so that values greater than 0xffff are not even useful.
Further changes: fixed a typo in the documentation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit f18f982ab ("sched: CPU hotplug events must not destroy scheduler
domains created by the cpusets") introduced a hotplug-related problem as
described below:
/*
* Force a reinitialization of the sched domains hierarchy. The domains
* and groups cannot be updated in place without racing with the balancing
* code, so we temporarily attach all running cpus to the NULL domain
* which will prevent rebalancing while the sched domains are recalculated.
*/
The sched-domains should be rebuilt when a CPU_DOWN ops. has been
completed, effectively either upon CPU_DEAD{_FROZEN} (upon success) or
CPU_DOWN_FAILED{_FROZEN} (upon failure -- restore the things to their
initial state). That's what update_sched_domains() also does but only
for !CPUSETS case.
With f18f982ab, sched-domains' reinitialization is delegated to
CPUSETS code:
Being called for CPU_UP_PREPARE and if its callback is called after
update_sched_domains()), it just negates all the work done by
update_sched_domains() -- i.e. a soon-to-be-offline cpu is included in
the sched-domains and that makes it visible for the load-balancer
while the CPU_DOWN ops. is in progress.
__migrate_live_tasks() moves the tasks off a 'dead' cpu (it's already
"offline" when this function is called).
try_to_wake_up() is called for one of these tasks from another CPU ->
the load-balancer (wake_idle()) picks up a "dead" CPU and places the
task on it. Then e.g. BUG_ON(rq->nr_running) detects this a bit later
-> oops.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com> Tested-by: Vegard Nossum <vegard.nossum@gmail.com> Cc: Paul Menage <menage@google.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: Paul Jackson <pj@sgi.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: miaox@cn.fujitsu.com Cc: rostedt@goodmis.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bsg: fix oops on remove
[SCSI] fusion: default MSI to disabled for SPI and FC controllers
[SCSI] ipr: Fix HDIO_GET_IDENTITY oops for SATA devices
[SCSI] mptspi: fix oops in mptspi_dv_renegotiate_work()
[SCSI] erase invalid data returned by device
Jeff Layton [Sat, 12 Jul 2008 20:48:00 +0000 (13:48 -0700)]
cifs: fix wksidarr declaration to be big-endian friendly
The current definition of wksidarr works fine on little endian arches
(since cpu_to_le32 is a no-op there), but on big-endian arches, it fails
to compile with this error:
error: braced-group within expression allowed only inside a function
The problem is that this static declaration has cpu_to_le32 embedded
within it, and that expands into a function macro. We need to use
__constant_cpu_to_le32() instead.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Cc: Steven French <sfrench@us.ibm.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Sat, 12 Jul 2008 20:47:59 +0000 (13:47 -0700)]
cifs: fix inode leak in cifs_get_inode_info_unix
Try this:
mount a share with unix extensions
create a file on it
umount the share
You'll get the following message in the ring buffer:
VFS: Busy inodes after unmount of cifs. Self-destruct in 5 seconds. Have a
nice day...
...the problem is that cifs_get_inode_info_unix is creating and hashing
a new inode even when it's going to return error anyway. The first
lookup when creating a file returns an error so we end up leaking this
inode before we do the actual create. This appears to be a regression
caused by commit 0e4bbde94fdc33f5b3d793166b21bf768ca3e098.
The following patch seems to fix it for me, and fixes a minor
formatting nit as well.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Acked-by: Steven French <sfrench@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log