The file opened in acct_on and freshly stored in the ns->bacct struct can
be closed in acct_file_reopen by a concurrent call after we release
acct_lock and before we call mntput(file->f_path.mnt).
Record file->f_path.mnt in a local variable and use this variable only.
Signed-off-by: Renaud Lottiaux <renaud.lottiaux@kerlabs.com> Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After downing/upping a cpu, an attempt to set
/proc/sys/vm/percpu_pagelist_fraction results in an oops in
percpu_pagelist_fraction_sysctl_handler().
If a processor is downed then we need to set the pageset pointer back to
the boot pageset.
Updates of the high water marks should not access pagesets of unpopulated
zones (those pointer go to the boot pagesets which would be no longer
functional if their size would be increased beyond zero).
When decoding (N)RPN sequencer events into raw MIDI commands, the
extra_decode_xrpn() function had accidentally swapped the MSB and LSB
controller values of both the parameter number and the data value.
According to the PCI PM specification (PCI Bus Power Management
Interface Specification, Rev. 1.2, Section 5.4.1) we are supposed to
reinitialize devices that have PCI_PM_CTRL_NO_SOFT_RESET clear during
all transitions from PCI_D3hot to PCI_D0, but we only do it if the
device's current_state field is equal to PCI_UNKNOWN.
This may lead to problems if a device with PCI_PM_CTRL_NO_SOFT_RESET
unset is put into PCI_D3hot at run time by its driver and
pci_set_power_state() is used to put it back into PCI_D0, because in
that case the device will remain uninitialized after
pci_set_power_state() has returned. Prevent that from happening by
modifying pci_raw_set_power_state() to reinitialize devices with
PCI_PM_CTRL_NO_SOFT_RESET unset during all transitions from D3 to D0.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a PCI device is not power-manageable either by the platform, or
with the help of the native PCI PM interface, pci_target_state() will
return either PCI_D3hot, or PCI_POWER_ERROR for it, depending on
whether or not the device is configured to wake up the system. Alas,
none of these return values is correct, because each of them causes
pci_prepare_to_sleep() to return error code, although it should
complete successfully in such a case.
Fix this problem by making pci_target_state() always return PCI_D0
for devices that cannot be power managed.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
parport_pc_probe_port() creates the own 'parport_pc' device if the
device argument is NULL. Then parport_pc_probe_port() doesn't
initialize the dma_mask and coherent_dma_mask of the device and calls
dma_alloc_coherent with it. dma_alloc_coherent fails because
dma_alloc_coherent() doesn't accept the uninitialized dma_mask:
http://lkml.org/lkml/2009/6/16/150
Long ago, X86_32 and X86_64 had the own dma_alloc_coherent
implementations; X86_32 accepted a device having dma_mask that is not
initialized however X86_64 didn't. When we merged them, we chose to
prohibit a device having dma_mask that is not initialized. I think
that it's good to require drivers to set up dma_mask (and
coherent_dma_mask) properly if the drivers want DMA.
CONFIG_PARPORT_PC_SUPERIO probes for various superio chips by writing
byte sequences to a set of different potential I/O ranges. But the
probed ranges are not exclusive to parallel ports. Some of our boards
just happen to have a watchdog in one of them. Took us almost a week
to figure out why some distros reboot without warning after running
flawlessly for 3 hours. For exactly 170 = 0xAA minutes, that is ...
Fixed by restoring original values after probing. Also fixed too small
request_region() in detect_and_report_it87().
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de> Signed-off-by: Alan Cox <alan@linux.intel.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the unlikely event that reshape progresses past the current request
while it is waiting for a stripe we need to schedule() before retrying
for 2 reasons:
1/ Prevent list corruption from duplicated list_add() calls without
intervening list_del().
2/ Give the reshape code a chance to make some progress to resolve the
conflict.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The minstrel rate controller periodically looks up rate indexes in
a sampling table. When accessing a specific row and column, minstrel
correctly does a bounds check which, on the surface, appears to handle
the case where mi->n_rates < 2. However, mi->sample_idx is actually
defined as an unsigned, so the right hand side is taken to be a huge
positive number when negative, and the check will always fail.
Consequently, the RC will overrun the array and cause random memory
corruption when communicating with a peer that has only a single rate.
The max value of mi->sample_idx is around 25 so casting to int should
have no ill effects.
Without the change, uptime is a few minutes under load with an AP
that has a single hard-coded rate, and both the AP and STA could
potentially crash. With the change, both lasted 12 hours with a
steady load.
Thanks to Ognjen Maric for providing the single-rate clue so I could
reproduce this.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=12490 on the
regression list (also http://bugzilla.kernel.org/show_bug.cgi?id=13000).
Reported-by: Sergey S. Kostyliov <rathamahata@gmail.com> Reported-by: Ognjen Maric <ognjen.maric@gmail.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86 stack traces are a piece of crap without frame pointers, and its not
like the 'performance gain' of not having stack pointers matters when you
selected lockdep.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <new-submission> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a system where system memory (according e820) is not covered by
mtrr, mtrr_trim_memory converts a portion of memory to reserved, but
bootloader has already put the initrd in that range.
Thus, we need to have 64bit to use relocate_initrd too.
[ Impact: fix using initrd when mtrr_trim_memory happen ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The missing device table means that the floppy module is not auto-loaded,
even when the appropriate PNP device (0700) is found.
We don't actually use the table in the module, since the device doesn't
have a struct pnp_driver, but it's sufficient to cause an alias in the
module that udev/modprobe will use.
Signed-off-by: Scott James Remnant <scott@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Philippe De Muyter <phdm@macqel.be> Acked-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Steve Holland pointed out that we forgot to call break; in the switch
statment. This probably resolves a lot of the bug reports I've gotten
for the driver lately.
Stupid me...
Reported-by: Steve Holland <sdh4@iastate.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In moxa.c there are 32 minor numbers reserved for each device. The number
of ports actually available per device is stored in
moxa_board_conf->numPorts. This number is not considered in moxa_open().
Opening a port that is not available results in a kernel oops. This patch
adds a test to moxa_open() that prevents opening unavailable ports.
Some users still load bond module multiple times to create bonding
devices. This accidentally was broken by a later patch about
the time sysfs was fixed. According to Jay, it was broken
by:
commit b8a9787eddb0e4665f31dd1d64584732b2b5d051
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Fri Jun 13 18:12:04 2008 -0700
bonding: Allow setting max_bonds to zero
Note: sysfs and procfs still produce WARN() messages when this is done
so the sysfs method is the recommended API.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove wrong fifo size definition for some AT91 products.
Due to a misunderstanding of some AT91 datasheets, a fifo size of 2048
(words) has been introduced by mistake. In fact, all products (AT91/AT32)
are sharing the same fifo size of 512 words.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peer reported:
| The bug is introduced from kernel 2.6.27, if E820 table reserve the memory
| above 4G in 32bit OS(BIOS-e820: 00000000fff80000 - 0000000120000000
| (reserved)), system will report Int 6 error and hang up. The bug is caused by
| the following code in drivers/firmware/memmap.c, the resource_size_t is 32bit
| variable in 32bit OS, the BUG_ON() will be invoked to result in the Int 6
| error. I try the latest 32bit Ubuntu and Fedora distributions, all hit this
| bug.
|======
|static int firmware_map_add_entry(resource_size_t start, resource_size_t end,
| const char *type,
| struct firmware_map_entry *entry)
and it only happen with CONFIG_PHYS_ADDR_T_64BIT is not set.
it turns out we need to pass u64 instead of resource_size_t for that.
[akpm@linux-foundation.org: add comment] Reported-and-tested-by: Peer Chen <pchen@nvidia.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Cc: Ingo Molnar <mingo@elte.hu> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some filesystems can call in to sync an inode that is still in the
I_NEW state (eg. ext family, when mounted with -osync). This is OK
because the filesystem has sole access to the new inode, so it can
modify i_state without races (because no other thread should be
modifying it, by definition of I_NEW). Ie. a false positive, so
remove the warnings.
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit code, we scan buffers attached to a transaction. During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head. So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.
This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).
Signed-off-by: Jan Kara <jack@suse.cz> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.
mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card. I have tested this, and removing the !
fixes the problem.
If you setserial a port which has never been initialised we change the type
but don't update the I/O method pointers. The same problem is true if you
change the io type of a port - but nobody ever does that so nobody noticed!
Remember the old type and when attaching if the type has changed reload the
port accessor pointers. We can't do it blindly as some 8250 drivers load custom
accessors and we must not stomp those.
netmos serial/parallel adapters come in different flavour differing only
by the number of parallel and serial ports, which are encoded in the
subdevice ID.
Last fix of Christian Pellegrin for 9855 2P2S broke support for 9855 1P4S,
and works only by side-effect for the first parallel port of a 2P2S, as
this first parallel port is found by reading the second addr entry of
(struct parport_pc_pci) cards[netmos_9855], which is not initialized, and
hence has value 0, which happens to be the BAR of the first parallel port.
netmos_9xx5_combo entry in (struct parport_pc_pci) cards[], which is used
for a 9845 1P4S must also be fixed for the parallel port support when
there are 4 serial ports because this entry currently gives 2 as BAR index
for the parallel port. Actually, in this case, BAR 2 is the 3rd serial
port while the parallel port is at BAR 4.
I fixed 9845 1P4S and 9855 1P4S support, while preserving 9855 2P2S support,
- by creating a netmos_9855_2p entry and using it for 9855 boards with 2
parallel ports : 9855 2P2S and 9855 2P0S boards,
- and by allowing netmos_parallel_init to change not only the number of
parallel ports (0 or 1), but making it also change the BAR index of the
parallel port when the serial ports are before the parallel port.
PS: the netmos_9855_2p entry in (struct pciserial_board)
pci_parport_serial_boards[] is needed because netmos_parallel_init has no
clean way to replace FL_BASE2 by FL_BASE4 in the description of the serial
ports in function of the number of parallel ports on the card.
Tested with 9845 1P4S, 9855 1P4S and 9855 2P2S boards.
Signed-off-by: Philippe De Muyter <phdm@macqel.be> Tested-by: Christian Pellegrin <chripell@fsfe.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If two CPU's simultaneously call ext4_ext_get_blocks() at the same
time, there is nothing protecting the i_cached_extent structure from
being used and updated at the same time. This could potentially cause
the wrong location on disk to be read or written to, including
potentially causing the corruption of the block group descriptors
and/or inode table.
This bug has been in the ext4 code since almost the very beginning of
ext4's development. Fortunately once the data is stored in the page
cache cache, ext4_get_blocks() doesn't need to be called, so trying to
replicate this problem to the point where we could identify its root
cause was *extremely* difficult. Many thanks to Kevin Shanahan for
working over several months to be able to reproduce this easily so we
could finally nail down the cause of the corruption.
The BH_Unwritten flag indicates that the buffer is allocated on disk
but has not been written; that is, the disk was part of a persistent
preallocation area. That flag should only be set when a get_blocks()
function is looking up a inode's logical to physical block mapping.
When ext4_get_blocks_wrap() is called with create=1, the uninitialized
extent is converted into an initialized one, so the BH_Unwritten flag
is no longer appropriate. Hence, we need to make sure the
BH_Unwritten is not left set, since the combination of BH_Mapped and
BH_Unwritten is not allowed; among other things, it will result ext4's
get_block() to be called over and over again during the write_begin
phase of write(2).
Use a very large unsigned number (~0xffff) as as the fake block number
for the delayed new buffer. The VFS should never try to write out this
number, but if it does, this will make it obvious.
We need to mark the buffer_head mapping preallocated space as new
during write_begin. Otherwise we don't zero out the page cache content
properly for a partial write. This will cause file corruption with
preallocation.
Now that we mark the buffer_head new we also need to have a valid
buffer_head blocknr so that unmap_underlying_metadata() unmaps the
correct block.
Don't try to look at i_file_acl_high unless the INCOMPAT_64BIT feature
bit is set. The field is normally zero, but older versions of e2fsck
didn't automatically check to make sure of this, so in the spirit of
"be liberal in what you accept", don't look at i_file_acl_high unless
we are using a 64-bit filesystem.
If the block containing external extended attributes (which is stored
in i_file_acl and i_file_acl_high) is larger than the on-disk
filesystem, the process which tried to access the extended attributes
will endlessly issue kernel printks complaining that
"__find_get_block_slow() failed", locking up that CPU until the system
is forcibly rebooted.
So when we read in the inode, make sure the i_file_acl value is legal,
and if not, flag the filesystem as being corrupted.
Update information about locking in JBD2 revoke code. Inconsistency in
comments found by Lin Tan <tammy000@gmail.com>
CC: Lin Tan <tammy000@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a mount option which allows the user to disable automatic
allocation of blocks whose allocation by delayed allocation when the
file was originally truncated or when the file is renamed over an
existing file. This feature is intended to save users from the
effects of naive application writers, but it reduces the effectiveness
of the delayed allocation code. This mount option disables this
safety feature, which may be desirable for prodcutions systems where
the risk of unclean shutdowns or unexpected system crashes is low.
With delayed allocation we should not/cannot discard inode prealloc
space during file close. We would still have dirty pages for which we
haven't allocated blocks yet. With this fix after each get_blocks
request we check whether we have zero reserved blocks and if yes and
we don't have any writers on the file we discard inode prealloc space.
When renaming a file such that a link to another inode is overwritten,
force any delay allocated blocks that to be allocated so that if the
filesystem is mounted with data=ordered, the data blocks will be
pushed out to disk along with the journal commit. Many application
programs expect this, so we do this to avoid zero length files if the
system crashes unexpectedly.
When closing a file that had been previously truncated, force any
delay allocated blocks that to be allocated so that if the filesystem
is mounted with data=ordered, the data blocks will be pushed out to
disk along with the journal commit. Many application programs expect
this, so we do this to avoid zero length files if the system crashes
unexpectedly.
Add an ioctl which forces all of the delay allocated blocks to be
allocated. This also provides a function ext4_alloc_da_blocks() which
will be used by the following commits to force files to be fully
allocated to preserve application-expected ext3 behaviour.
Some poeple are reading the ext4 feature list too literally and create
dubious test cases involving very long filenames and 1k blocksize and
then complain when they run into an htree-imposed limit. So add fine
print to the "fix 32000 subdirectory limit" ext4 feature.
ext4_iget() returns -ESTALE if invoked on a deleted inode, in order to
report errors to NFS properly. However, in ext4_lookup(), this
-ESTALE can be propagated to userspace if the filesystem is corrupted
such that a directory entry references a deleted inode. This leads to
a misleading error message - "Stale NFS file handle" - and confusion
on the part of the admin.
The bug can be easily reproduced by creating a new filesystem, making
a link to an unused inode using debugfs, then mounting and attempting
to ls -l said link.
This patch thus changes ext4_lookup to return -EIO if it receives
-ESTALE from ext4_iget(), as ext4 does for other filesystem metadata
corruption; and also invokes the appropriate ext*_error functions when
this case is detected.
At the moment there are few restrictions on which flags may be set on
which inodes. Specifically DIRSYNC may only be set on directories and
IMMUTABLE and APPEND may not be set on links. Tighten that to disallow
TOPDIR being set on non-directories and only NODUMP and NOATIME to be set
on non-regular file, non-directories.
Introduces a flags masking function which masks flags based on mode and
use it during inode creation and when flags are set via the ioctl to
facilitate future consistency.
At present INDEX and EXTENTS are the only flags that new ext4 inodes do
NOT inherit from their parent. In addition prevent the flags DIRTY,
ECOMPR, IMAGIC, TOPDIR, HUGE_FILE and EXT_MIGRATE from being inherited.
List inheritable flags explicitly to prevent future flags from
accidentally being inherited.
This fixes the TOPDIR flag inheritance bug reported at
http://bugzilla.kernel.org/show_bug.cgi?id=9866.
HPET on AMD 81xx chipset needs a second write (with HPET_TN_SETVAL
cleared) to T0_CMP register to set the period in periodic mode.
With this patch HPET_COUNTER is still stopped but not reset when HPET
is programmed in periodic mode. This should help to avoid races when
HPET is programmed in periodic mode and fixes a boot time hang that
I've observed on a machine when using 1000HZ.
[ Impact: fix boot time hang on machines with AMD 81xx chipset ]
Reported-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Tested-by: Jeff Mahoney <jeffm@suse.com>
LKML-Reference: <20090421180037.GA2763@alberich.amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86: hpet: stop HPET_COUNTER when programming periodic mode
Impact: fix system hang on some systems operating with HZ_1000
On a system that stalled with HZ_1000, the first value written to
T0_CMP (when the main counter was not stopped) did not trigger an
interrupt. Instead after the main counter wrapped around (after
several minutes) an interrupt was triggered and afterwards the
periodic interrupt took effect.
This can be fixed by implementing HPET spec recommendation for
programming the periodic mode (i.e. stopping the main counter).
When ptrace_detach() takes tasklist, the tracee can be SIGKILL'ed. If it
has already passed exit_notify() we can leak a zombie, because a) ptracing
disables the auto-reaping logic, and b) ->real_parent was not notified
about the child's death.
ptrace_detach() should follow the ptrace_exit's logic, change the code
accordingly.
ignoring_children() takes parent->sighand->siglock and checks
k_sigaction[SIGCHLD] atomically. But this buys nothing, we can't get the
"really" wrong result even if we race with sigaction(SIGCHLD). If we read
the "stale" sa_handler/sa_flags we can pretend it was changed right after
the check.
Remove spin_lock(->siglock), and kill "int ign" which caches the result of
ignoring_children() which becomes rather trivial.
Perhaps it makes sense to export this helper, do_notify_parent() can use
it too.
Move the code from __ptrace_detach() to its single caller and kill this
helper.
Also, fix the ->exit_state check, we shouldn't wake up EXIT_DEAD tasks.
Actually, I think task_is_stopped_or_traced() makes more sense, but this
needs another patch.
The commit a760a6656e6f00bb0144a42a048cf0266646e22c (crypto:
api - Fix module load deadlock with fallback algorithms) broke
the auto-loading of algorithms that require fallbacks. The
problem is that the fallback mask check is missing an and which
cauess bits that should be considered to interfere with the
result.
Since the padlock-aes driver doesn't require a fallback (it's
only padlock-sha that does), it should use the aes alias rather
than aes-all so that ones that do need a fallback can use it.
When request_key() is called, without there being any standard process
keyrings on which to fall back if a destination keyring is not specified, an
oops is liable to occur when construct_alloc_key() calls down_write() on
dest_keyring's semaphore.
Due to function inlining this may be seen as an oops in down_write() as called
from request_key_and_link().
This situation crops up during boot, where request_key() is called from within
the kernel (such as in CIFS mounts) where nobody is actually logged in, and so
PAM has not had a chance to create a session keyring and user keyrings to act
as the fallback.
To fix this, make construct_alloc_key() not attempt to cache a key if there is
no fallback key if no destination keyring is given specifically.
Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ACM sets the low latency flag but calls the flip buffer routines from
IRQ context which isn't permitted (and as of 2.6.29 causes a warning
hence this one was caught)
Fortunatelt ACM doesn't need to set this flag in the first place as it
only set it to work around problems in ancient (pre tty flip rewrite)
kernels.
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :
WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de> Cc: Matt Mackall <mpm@selenic.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a really simple patch that basically just open-codes the current
"secure_ip_id()" call, but when open-coding it we now use a _static_
hashing area, so that it gets updated every time.
And to make sure somebody can't just start from the same original seed of
all-zeroes, and then do the "half_md4_transform()" over and over until
they get the same sequence as the kernel has, each iteration also mixes in
the same old "current->pid + jiffies" we used - so we should now have a
regular strong pseudo-number generator, but we also have one that doesn't
have a single seed.
Note: the "pid + jiffies" is just meant to be a tiny tiny bit of noise. It
has no real meaning. It could be anything. I just picked the previous
seed, it's just that now we keep the state in between calls and that will
feed into the next result, and that should make all the difference.
I made that hash be a per-cpu data just to avoid cache-line ping-pong:
having multiple CPU's write to the same data would be fine for randomness,
and add yet another layer of chaos to it, but since get_random_int() is
supposed to be a fast interface I did it that way instead. I considered
using "__raw_get_cpu_var()" to avoid any preemption overhead while still
getting the hash be _mostly_ ping-pong free, but in the end good taste won
out.
Add barrier() to bnx2_get_hw_{tx|rx}_cons() to fix this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=12698
This issue was reported by multiple i386 users. Without barrier(),
the compiled code looks like the following where %eax contains the
address of the tx_cons or rx_cons in the DMA status block. The
status block contents can change between the cmpb and the movzwl
instruction. The driver would crash if the value was not 0xff during
the cmpb instruction, but changed to 0xff during the movzwl
instruction.
Thanks to Pascal de Bruijn <pmjdebruijn@pcode.nl> for reporting the
problem and Holger Noefer <hnoefer@pironet-ndh.com> for patiently
testing test patches for us.
[greg - took out version change]
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"There is another problem with this piece of code. The sband will be NULL
after second iteration on single band device and cause null pointer
dereference. Everything is working with dual band card. Sorry, but i
don't know how to explain this clearly in English. I have looked on the
second patch for pid algorithm and found similar bug."
Reported-by: Karol Szuster <qflon@o2.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pid doesn't count with some band having more bitrates than the one
associated the first time.
Fix that by counting the maximal available bitrate count and allocate
big enough space.
Secondly, fix touching uninitialized memory which causes panics.
Index sucked from this random memory points to the hell.
The fix is to sort the rates on each band change.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
minstrel doesn't count max rate count in fact, since it doesn't use
a loop variable `i' and hence allocs space only for bitrates found in
the first band.
Fix it by involving the `i' as an index so that it traverses all the
bands now and finds the real max bitrate count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be symmetrical in what is done when key is set and cleared.
This is important wrt the key flags as they are used during key
clearing and if they are not set when the key is set the key cannot be
cleared completely.
This addresses the many occurences of the WARN found in
iwl_set_tkip_dynamic_key_info() and tracked in
http://www.kerneloops.org/searchweek.php?search=iwl_set_dynamic_key
If calling iwl_set_tkip_dynamic_key_info()/iwl_remove_dynamic_key()
pair a few times in a row will cause that we run out of key space.
This is because the index stored in the key flags is used by
iwl_remove_dynamic_key() to decide if it should remove the key.
Unfortunately the key flags, and hence the key index is currently only
set at the time the key is written to the device (in
iwl_update_tkip_key()) and _not_ in iwl_set_tkip_dynamic_key_info().
Fix this by setting flags in iwl_set_tkip_dynamic_key_info().
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Kirsher [Tue, 2 Jun 2009 23:38:52 +0000 (16:38 -0700)]
igb: fix LRO warning
This fix is only needed for 2.6.29.y tree, since in 2.6.30 and later IGB
has moved to using GRO instead of LRO.
igb supports LRO, but was not setting any hooks to the ->set_flags
ethtool_ops function. This would trigger warnings if the user tried
to enable or disable LRO.
Based on the patch provided by Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Sergey Kononenko <sergk@sergk.org.ua> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Tested-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eric Paris [Mon, 1 Jun 2009 14:21:05 +0000 (10:21 -0400)]
SELinux: BUG in SELinux compat_net code
This patch is not applicable to Linus's tree as the code in question has
been removed for 2.6.30. I'm sending in case any of the stable
maintainers would like to push to their branches (which I think anything
pre 2.6.30 would like to do).
Ubuntu users were experiencing a kernel panic when they enabled SELinux
due to an old bug in our handling of the compatibility mode network
controls, introduced Jan 1 2008 effad8df44261031a882e1a895415f7186a5098e
Most distros have not used the compat_net code since the new code was
introduced and so noone has hit this problem before. Ubuntu is the only
distro I know that enabled that legacy cruft by default. But, I was ask
to look at it and found that the above patch changed a call to
avc_has_perm from if(send_perm) to if(!send_perm) in
selinux_ip_postroute_iptables_compat(). The result is that users who
turn on SELinux and have compat_net set can (and oftern will) BUG() in
avc_has_perm_noaudit since they are requesting 0 permissions.
This patch corrects that accidental bug introduction.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Under CONFIG_MAXSMP, cpus_hardware_enabled is allocated from the heap and
not statically initialized. This causes a crash on reboot when kvm thinks
vmx is enabled on random nonexistent cpus and accesses nonexistent percpu
lists.
Fix by explicitly clearing the variable.
Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
When AMD C1E is enabled, local APIC timer will stop even in C1. To avoid
suspend/resume hang, this patch removes C1 and replace it with a cpu_relax() in
suspend/resume path. This hasn't any impact in runtime path.
http://bugzilla.kernel.org/show_bug.cgi?id=13233
[ impact: avoid suspend/resume hang in AMD CPU with C1E enabled ]
Tested-by: Dmitry Lyzhyn <thisistempbox@yahoo.com> Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pascal reported and bisected a commit:
| x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case
which broke one system system.
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
PCI: MCFG area at f0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
it didn't have
PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
anymore, and try to use 0xf000000 - 0xffffffff for mmconfig
For 32bit, mcfg_res->end could be 32bit only (if 64 resources aren't used)
So use end - 1 to pass the value in mcfg->end to avoid overflow.
We don't need to worry about the e820 path, they are always 64 bit.
This patch (as1244) fixes a crash in usb-serial that occurs when a
sub-driver returns a positive value from its attach method, indicating
that new firmware was loaded and the device will disconnect and
reconnect. The usb-serial core then skips the step of registering the
port devices; when the disconnect occurs, the attempt to unregister
the ports fails dramatically.
This problem shows up with Keyspan devices and it might affect others
as well.
When the attach method returns a positive value, the patch sets
num_ports to 0. This tells usb_serial_disconnect() not to try
unregistering any of the ports; instead they are cleaned up by
destroy_serial().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kernel 2.6.18 broke the MotU Fastlane, which uses duplicate endpoint
numbers in a manner that is not only illegal but also confuses the
kernel's endpoint descriptor caching mechanism. To work around this, we
have to add a separate usb_set_interface() call to guide the USB core to
the correct descriptors.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: David Fries <david@fries.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver (and presumably others) allocates several URBs when it
opens and tries to free them when it closes. The isp1760_urb_dequeue
function gets called, but the packet being dequeued is not necessarily at
the
front of one of the 32 queues. If not, the isp1760_urb_done function doesn't
get called for the URB and the process trying to free it hangs forever on a
wait_queue. This patch does two things. If the URB being dequeued has others
queued behind it, it re-queues them. And it searches the queues looking for
the URB being dequeued rather than just looking at the one at the front of
the queue.
hugetlbfs reserves huge pages but does not fault them at mmap() time to
ensure that future faults succeed. The reservation behaviour differs
depending on whether the mapping was mapped MAP_SHARED or MAP_PRIVATE.
For MAP_SHARED mappings, hugepages are reserved when mmap() is first
called and are tracked based on information associated with the inode.
Other processes mapping MAP_SHARED use the same reservation. MAP_PRIVATE
track the reservations based on the VMA created as part of the mmap()
operation. Each process mapping MAP_PRIVATE must make its own
reservation.
hugetlbfs currently checks if a VMA is MAP_SHARED with the VM_SHARED flag
and not VM_MAYSHARE. For file-backed mappings, such as hugetlbfs,
VM_SHARED is set only if the mapping is MAP_SHARED and the file was opened
read-write. If a shared memory mapping was mapped shared-read-write for
populating of data and mapped shared-read-only by other processes, then
hugetlbfs would account for the mapping as if it was MAP_PRIVATE. This
causes processes to fail to map the file MAP_SHARED even though it should
succeed as the reservation is there.
This patch alters mm/hugetlb.c and replaces VM_SHARED with VM_MAYSHARE
when the intent of the code was to check whether the VMA was mapped
MAP_SHARED or MAP_PRIVATE.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: <starlight@binnacle.cx> Cc: Eric B Munson <ebmunson@us.ibm.com> Cc: Adam Litke <agl@us.ibm.com> Cc: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On x86 and x86-64, it is possible that page tables are shared beween
shared mappings backed by hugetlbfs. As part of this,
page_table_shareable() checks a pair of vma->vm_flags and they must match
if they are to be shared. All VMA flags are taken into account, including
VM_LOCKED.
The problem is that VM_LOCKED is cleared on fork(). When a process with a
shared memory segment forks() to exec() a helper, there will be shared
VMAs with different flags. The impact is that the shared segment is
sometimes considered shareable and other times not, depending on what
process is checking.
What happens is that the segment page tables are being shared but the
count is inaccurate depending on the ordering of events. As the page
tables are freed with put_page(), bad pmd's are found when some of the
children exit. The hugepage counters also get corrupted and the Total and
Free count will no longer match even when all the hugepage-backed regions
are freed. This requires a reboot of the machine to "fix".
This patch addresses the problem by comparing all flags except VM_LOCKED
when deciding if pagetables should be shared or not for hugetlbfs-backed
mapping.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: <starlight@binnacle.cx> Cc: Eric B Munson <ebmunson@us.ibm.com> Cc: Adam Litke <agl@us.ibm.com> Cc: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Its possible for cfg80211 to have scheduled the work and for
the global workqueue to not have kicked in prior to a cfg80211
driver's regulatory hint or wiphy_apply_custom_regulatory().
Although this is very unlikely its possible and should fix
this race. When this race would happen you are expected to have
hit a null pointer dereference panic.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The processor is documented to reload the PDPTRs while in PAE mode if any
of the CR4 bits PSE, PGE, or PAE change. Linux relies on this
behaviour when zapping the low mappings of PAE kernels during boot.
The code already handled changes to CR4.PAE; augment it to also notice changes
to PSE and PGE.
This triggered while booting an F11 PAE kernel; the futex initialization code
runs before any CR3 reloads and writes to a NULL pointer; the futex subsystem
ended up uninitialized, killing PI futexes and pulseaudio which uses them.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log