On writes in MODE_RAW the mtd_oob_ops struct is not sufficiently
initialized which may cause nandwrite to fail. With this patch
it is possible to write raw nand/oob data without additional ECC
(either for testing or when some sectors need different oob layout
e.g. bootloader) like
nandwrite -n -r -o /dev/mtd0 <myfile>
Only AID values 1-2007 are valid, but some APs have been
found to send random bogus values, in the reported case an
AP that was sending the AID field value 0xffff, an AID of
0x3fff (16383).
There isn't much we can do but disable powersave since
there's no way it can work properly in this case.
Reported-by: Bill C Riemers <briemers@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The offchannel code is currently broken - we should
remain_off_channel if the work was started, and
the work's channel and channel_type are the same
as local->tmp_channel and local->tmp_channel_type.
However, if wk->chan_type and local->tmp_channel_type
coexist (e.g. have the same channel type), we won't
remain_off_channel.
This behavior was introduced by commit da2fd1f
("mac80211: Allow work items to use existing
channel type.")
Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
L2TP for example uses NLA_MSECS like this:
policy:
[L2TP_ATTR_RECV_TIMEOUT] = { .type = NLA_MSECS, },
code:
if (info->attrs[L2TP_ATTR_RECV_TIMEOUT])
cfg.reorder_timeout = nla_get_msecs(info->attrs[L2TP_ATTR_RECV_TIMEOUT]);
As nla_get_msecs() is essentially nla_get_u64() plus the
conversion to a HZ-based value, this will not properly
reject attributes from userspace that aren't long enough
and might overrun the message.
Add NLA_MSECS to the attribute minlen array to check the
size properly.
Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recently the ACPI ops structs were constified but the inline version
of register_hotplug_dock_device() was overlooked (see also commit 9c8b04b, June 25 2011). Update the inline function
register_hotplug_dock_device() that is enabled with
CONFIG_ACPI_DOCK=n too. This patch fixes at least the following
compiler warnings:
drivers/ata/libata-acpi.c: In function .ata_acpi_associate.:
drivers/ata/libata-acpi.c:266:11: warning: passing argument 2 of .register_hotplug_dock_device. discards qualifiers from pointer target type
include/acpi/acpi_drivers.h:146:19: note: expected .struct acpi_dock_ops *. but argument is of type .const struct acpi_dock_ops *.
drivers/ata/libata-acpi.c:275:11: warning: passing argument 2 of .register_hotplug_dock_device. discards qualifiers from pointer target type
include/acpi/acpi_drivers.h:146:19: note: expected .struct acpi_dock_ops *. but argument is of type .const struct acpi_dock_ops *.
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Callers to __acpi_ioremap_fast() pass the bit_width that they found in the
acpi_generic_address structure. Convert from bits to bytes when passing to
__acpi_find_iomap() - as it wants to see bytes, not bits.
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 188917e183cf9ad0374b571006d0fc6d48a7f447, /proc/ppc64 is a
symlink to /proc/powerpc/. That means that creating /proc/ppc64/eeh will
end up with a unaccessible file, that is not listed under /proc/powerpc/
and, then, not listed under /proc/ppc64/.
Creating /proc/powerpc/eeh fixes that problem and maintain the
compatibility intended with the ppc64 symlink.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In create_section_mapping we BUG if htab_bolt_mapping returned
an error. A better approach is to return an error which will
propagate back to userspace.
This patch fixes another bug from LUN_RESET re-org fallout in
core_tmr_drain_tmr_list() that was adding the wrong se_tmr_req
into the local drain_tmr_list to be walked + released.
Signed-off-by: Joern Engel <joern@logfs.org> Cc: Joern Engel <joern@logfs.org> Reviewed-by: Roland Dreier <roland@purestorage.com> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug in core_tmr_drain_tmr_list() where drain_tmr_list
was using the wrong se_tmr_req for cmd assignment due to a typo during the
LUN_RESET re-org. This was resulting in general protection faults while
using the leftover bogus *tmr_p pointer from list_for_each_entry_safe().
Signed-off-by: Joern Engel <joern@logfs.org> Cc: Joern Engel <joern@logfs.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.
A dm-multipath user reported[1] a problem when trying to boot
a kernel with commit 4853abaae7e4a2af938115ce9071ef8684fb7af4
(block: fix flush machinery for stacking drivers with differring
flush flags) applied. It turns out that an empty flush request
can be sent into blk_insert_flush. When the BUG_ON was fixed
to allow for this, I/O on the underlying device would stall. The
reason is that blk_insert_cloned_request does not kick the queue.
In the aforementioned commit, I had added a special case to
kick the queue if data was sent down but the queue flags did
not require a flush. A better solution is to push the queue
kick up into blk_insert_cloned_request.
This patch, along with a follow-on which fixes the BUG_ON, fixes
the issue reported.
A user reported a regression due to commit 4853abaae7e4a2af938115ce9071ef8684fb7af4 (block: fix flush
machinery for stacking drivers with differring flush flags).
Part of the problem is that blk_insert_flush required a
single bio be attached to the request. In reality, having
no attached bio is also a valid case, as can be observed with
an empty flush.
The P600 requires a small delay when changing states. Otherwise we may think
the board did not reset and we bail. This for kdump only and is particular
to the P600.
Signed-off-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one in their right mind would expect statfs() to not work on a
automounter managed mount point. Fix it.
[ I'm not sure about the "no one in their right mind" part. It's not
mounted, and you didn't ask for it to be mounted. But nobody will
really care, and this probably makes it match previous semantics, so..
- Linus ]
We did not increment the amount of sectors written to disk
b/c we tested for the == WRITE which is incorrect - as the
operations are more of WRITE_FLUSH, WRITE_ODIRECT. This patch
fixes it by doing a & WRITE check.
Reported-by: Andy Burns <xen.lists@burns.me.uk> Suggested-by: Ian Campbell <Ian.Campbell@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is because bdev holds on to disk but disk doesn't pin the
associated queue. If a SCSI device is removed while the device is
still open, the sdev puts the base reference to the queue on release.
When the bdev is finally released, the associated queue is already
gone along with the bdi and bdev_inode_switch_bdi() ends up
dereferencing already freed bdi.
Even if it were not for this bug, disk not holding onto the associated
queue is very unusual and error-prone.
Fix it by making add_disk() take an extra reference to its queue and
put it on disk_release() and ensuring that disk and its fops owner are
put in that order after all accesses to the disk and queue are
complete.
The sunrpc layer keeps a cache of recently used credentials and
'unx_match' is used to find the credential which matches the current
process.
However unx_match allows a match when the cached credential has extra
groups at the end of uc_gids list which are not in the process group list.
So if a process with a list of (say) 4 group accesses a file and gains
access because of the last group in the list, then another process
with the same uid and gid, and a gid list being the first tree of the
gids of the original process tries to access the file, it will be
granted access even though it shouldn't as the wrong rpc credential
will be used.
Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call to complete() in st_scsi_execute_end() wakes up sleeping thread
in write_behind_check(), which frees the st_request, thus invalidating
the pointer to the associated bio structure, which is then passed to the
blk_rq_unmap_user(). Fix by storing pointer to bio structure into
temporary local variable.
This bug is present since at least linux-2.6.32.
Signed-off-by: Petr Uzel <petr.uzel@suse.cz> Reported-by: Juergen Groß <juergen.gross@ts.fujitsu.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addresses two issues with non immediate TMR handling in
iscsit_handle_task_mgt_cmd(). The first involves breakage due to
v3.1-rc conversion of iscsit_sequence_cmd(), which upon good status
would hit the iscsit_add_reject_from_cmd() block of code. This patch
adds an explict check for CMDSN_ERROR_CANNOT_RECOVER.
The second adds a check to return when non immediate TMR operation is
detected after iscsit_ack_from_expstatsn(), as iscsit_sequence_cmd()
-> iscsit_execute_cmd() will have called transport_generic_handle_tmr()
for the non immediate TMR case already.
Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a missing CMDSN_LOWER_THAN_EXP return check for
iscsit_sequence_cmd() in iscsit_handle_scsi_cmd() that was incorrectly
dropped during the v3.1-rc cleanups to use iscsit_sequence_cmd().
Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addresses an issue with buggy userspace code sending I/O
via scsi-generic that does not explictly clear their associated read
buffers. It adds an explict memset of the first SGL entry within
tcm_loop_new_cmd_map() for SCF_SCSI_CONTROL_SG_IO_CDB payloads that
are currently guaranteed to be a single SGL by target-core code.
This issue is a side effect of the v3.1-rc1 merge to remove the
extra memcpy between certain control CDB types using a contigious
+ cleared buffer in target-core, and performing a memcpy into the
SGL list within tcm_loop.
It was originally mainfesting itself by udev + scsi_id + scsi-generic
not properly setting up the expected /dev/disk/by-id/ symlinks because
the INQUIRY payload was containing extra bogus data preventing the
proper NAA IEEE WWN from being parsed by userspace.
Cc: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 2265cef2 (hwmon: (w83627ehf) Properly report PECI and AMD-SI
sensor types) results in kernel panic if data->temp_label was not
initialized.
The problem was found with chip W83627DHG-P.
Add check if data->temp->label was set before use.
Based on incomplete patch by Alexander Beregalov.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com> Tested-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When temperature sources are PECI or AMD-SI agents, it makes no sense
to report their type as diode or thermistor. Instead we must report
their digital nature.
The P600 requires a small delay when changing states. Otherwise we may think
the board did not reset and we bail. This for kdump only and is particular
to the P600.
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit f71648d73c1650b8b4aceb3856bebbde6daa3b86 (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. A companion
patch changes the PM core's behavior, but we also need to change the
USB core. In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit f71648d73c1650b8b4aceb3856bebbde6daa3b86 (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. Therefore
this patch (as1492) adds a mechanism for retrying failed
autosuspends. If the callback routine updates the last_busy field so
that the next autosuspend expiration time is in the future, the
autosuspend will automatically be rescheduled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Help text under choice menu is never displayed because it does not have
symbol name associated with it, however many kconfigs have help text
under choice, assuming that it will be displayed when user selects help.
for example in Kconfig if we have:
choice
prompt "Choice"
---help---
HELP TEXT ...
config A
bool "A"
config B
bool "B"
endchoice
Without this patch "HELP TEXT" is not displayed when user selects help
option when "Choice" is highlighted from menuconfig or xconfig or
gconfig.
This patch changes the logic in menu_get_ext_help to display help for
cases which dont have symbol names like choice.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Reviewed-by: Stuart Menefy <stuart.menefy@st.com> Reviewed-by: Arnaud Lacombe <lacombar@gmail.com> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Polarity needs to be set accordingly to connector status (connected
or disconnected). Set it up in hpd_init() so first hotplug works
reliably no matter what is the initial set of connector. hpd_init()
also covers resume so HPD will work correctly after resume as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: Jerome Glisse <j.glisse@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow the user to override whether MSIs are enabled
or not on supported ASICs. MSIs are disabled by default
on IGP chips as they tend not to work. However certain
IGP chips only seem to work with MSIs enabled.
I suspect this is a chipset or bios issue, but I'm not sure
what the proper fix is. This will at least make diagnosing
and working around the problem much easier.
Polarity needs to be set accordingly to connector status (connected
or disconnected). Set it up at module init so first hotplug works
reliably no matter what is the initial set of connector.
Since force handling rework of d0d0a225e6ad43314c9aa7ea081f76adc5098ad4
we could end up bouncing connector status btw disconnected and unknown.
When connector status change a call to output_poll_changed happen which
in turn ask again for detect but with force set.
So set the load detect flags whenever we report the connector as
connected or unknown this avoid bouncing btw disconnected and unknown.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Cc: Stefan Lippers-Hollmann <s.L-H@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The regression-fix in 3.1 for the check of DMA-position validity caused
yet another regression for CA0110. As usual, this hardware seems working
only with LPIB properly. Adding the appropriate driver-caps bit to force
LPIB fixes the problem.
The 3.1 kernel has a regression for ALC861 codec where no sound output
is heard with the default setup. It's because the amps in DACs aren't
properly unmuted while the output mixers are assigned only to pins.
This patch fixes the missing initialization of DACs when no mixer is
assigned to them.
Some BIOS report invalid pins as digital output pins. The driver checks
the connection but it doesn't do it fully correctly, and it leaves some
undefined value as the audio-out widget, which makes the driver spewing
warnings. This patch fixes the issue.
When the driver finds multiple ADCs, it tries to create an alternative
capture PCM stream. However, these secondary ADCs might be useless or
in uncontrolled paths in some cases, e.g. when auto-mic or dynamic
ADC-switching is enabled. Also, when only a single capture source is
available, the multi-streams don't make sense, too.
With this patch, the driver checks such condition and skips the alt
stream appropriately.
If the device is unplugged while running, it is possible for a PCM
device to be closed after the disconnect callback has returned. This
means that kill_stream_urb() and disable_iso_interface() would try to
access already-invalid or freed USB data structures.
The function free_usb_related_resources() was intended to prevent this,
but forgot to clear the affected variables.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
s390 didn't return 0 in that case, if it's rolling back the *nr pointer it
should also return zero to avoid adding pages to the array at the wrong
offset.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
powerpc didn't return 0 in that case, if it's rolling back the *nr pointer
it should also return zero to avoid adding pages to the array at the wrong
offset.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Gibson <david@gibson.dropbear.id.au> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"page" may have changed to point to the next hugepage after the loop
completed, The references have been taken on the head page, so the
put_page must happen there too.
This is a longstanding issue pre-thp inclusion.
It's totally unclear how these page_cache_add_speculative and
pte_val(pte) != pte_val(*ptep) checks are necessary across all the
powerpc gup_fast code, when x86 doesn't need any of that: there's no way
the page can be freed with irq disabled so we're guaranteed the
atomic_inc will happen on a page with page_count > 0 (so not needing the
speculative check).
The pte check is also meaningless on x86: no need to rollback on x86 if
the pte changed, because the pte can still change a CPU tick after the
check succeeded and it won't be rolled back in that case. The important
thing is we got a reference on a valid page that was mapped there a CPU
tick ago. So not knowing the soft tlb refill code of ppc64 in great
detail I'm not removing the "speculative" page_count increase and the
pte checks across all the code, but unless there's a strong reason for
it they should be later cleaned up too.
If a pte can change from huge to non-huge (like it could happen with
THP) passing a pte_t *ptep to gup_hugepte() would also require to repeat
the is_hugepd in gup_hugepte(), but that shouldn't happen with hugetlbfs
only so I'm not altering that.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This part of gup_fast doesn't seem capable of handling hugetlbfs ptes,
those should be handled by gup_hugepd only, so these checks are
superfluous.
Plus if this wasn't a noop, it would have oopsed because, the insistence
of using the speculative refcounting would trigger a VM_BUG_ON if a tail
page was encountered in the page_cache_get_speculative().
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the link state changes, xHC will report a port status change event
and set the PORT_PLC bit, for both USB3 and USB2 root hub ports.
The PLC will be cleared by usbcore for USB3 root hub ports, but not for
USB2 ports, because they do not report USB_PORT_STAT_C_LINK_STATE in
wPortChange.
Clear it for USB2 root hub ports in handle_port_status().
Some alternate interface settings have no endpoints associated with them.
This shows up in some USB webcams, particularly the Logitech HD 1080p,
which uses the uvcvideo driver. If a driver switches between two alt
settings with no endpoints, there is no need to issue a configure endpoint
command, because there is no endpoint information to update.
The only time a configure endpoint command with just the add slot flag set
makes sense is when the driver is updating hub characteristics in the slot
context. However, that code never calls xhci_check_bandwidth, so we
should be safe not issuing a command if only the slot context add flag is
set.
Scanning cannot be run during suspend or hibernation, but if
usb-stor-scan freezes another thread waiting on scanning to
complete may fail to freeze.
However, if usb-stor-scan is left freezable without ever actually
freezing then the freezer will wait on it to exit, and threads
waiting for scanning to finish will no longer be blocked. One
problem with this approach is that usb-stor-scan has a delay to
wait for devices to settle (which is currently the only point where
it can freeze). To work around this we can request that the freezer
send a fake signal when freezing, then use interruptible sleep to
wake the thread early when freezing happens.
To make this happen, the following changes are made to
usb-stor-scan:
* Use set_freezable_with_signal() instead of set_freezable() to
request a fake signal when freezing
* Use wait_event_interruptible_timeout() instead of
wait_event_freezable_timeout() to avoid freezing
Ceph users reported that when using Ceph on ext4, the filesystem
would often become corrupted, containing inodes with incorrect
i_blocks counters.
I managed to reproduce this with a very hacked-up "streamtest"
binary from the Ceph tree.
Ceph is doing a lot of xattr writes, to out-of-inode blocks.
There is also another thread which does sync_file_range and close,
of the same files. The problem appears to happen due to this race:
do_writepages ext4_xattr_set
ext4_da_writepages ext4_xattr_set_handle
mpage_da_map_blocks ext4_xattr_block_set
set DELALLOC_RESERVE
ext4_new_meta_blocks
ext4_mb_new_blocks
if (!i_delalloc_reserved_flag)
vfs_dq_alloc_block
ext4_get_blocks
down_write(i_data_sem)
set i_delalloc_reserved_flag
...
up_write(i_data_sem)
if (i_delalloc_reserved_flag)
vfs_dq_alloc_block_nofail
In other words, the sync/flush thread pops in and sets
i_delalloc_reserved_flag on the inode, which makes the xattr thread
think that it's in a delalloc path in ext4_new_meta_blocks(),
and add the block for a second time, after already having added
it once in the !i_delalloc_reserved_flag case in ext4_mb_new_blocks
The real problem is that we shouldn't be using the DELALLOC_RESERVED
state flag, and instead we should be passing
EXT4_GET_BLOCKS_DELALLOC_RESERVE down to ext4_map_blocks() instead of
using an inode state flag. We'll fix this for now with using
i_data_sem to prevent this race, but this is really not the right way
to fix things.
ext4_dx_add_entry manipulates bh2 and frames[0].bh, which are two buffer_heads
that point to directory blocks assigned to the directory inode. However, the
function calls ext4_handle_dirty_metadata with the inode of the file that's
being added to the directory, not the directory inode itself. Therefore,
correct the code to dirty the directory buffers with the directory inode, not
the file inode.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ext4_mkdir calls ext4_handle_dirty_metadata with dir_block and the inode "dir".
Unfortunately, dir_block belongs to the newly created directory (which is
"inode"), not the parent directory (which is "dir"). Fix the incorrect
association.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ext4_rename performs a directory rename (move), dir_bh is a
buffer that is modified to update the '..' link in the directory being
moved (old_inode). However, ext4_handle_dirty_metadata is called with
the old parent directory inode (old_dir) and dir_bh, which is
incorrect because dir_bh does not belong to the parent inode. Fix
this error.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This doesn't make much sense, and it exposes a bug in the kernel where
attempts to create a new file in an append-only directory using
O_CREAT will fail (but still leave a zero-length file). This was
discovered when xfstests #79 was generalized so it could run on all
file systems.
Since we're using non-atomic radix tree allocations, we
should be protecting the tree using a mutex and not a
spinlock.
Non-atomic allocations and process context locking is good enough,
as the tree is manipulated only when locks are registered/
unregistered/requested/freed.
The locks themselves are still protected by spinlocks of course,
and mutexes are not involved in the locking/unlocking paths.
Signed-off-by: Juan Gutierrez <jgutierrez@ti.com>
[ohad@wizery.com: rewrite the commit log, #include mutex.h, add minor
commentary]
[ohad@wizery.com: update register/unregister parts in hwspinlock.txt] Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[There is no upstream commit for this patch since the corresponding
code was removed from 3.2 kernel. This is a regression found only in
3.1 kernel, so please apply this only to 3.1.x series.]
Some ALC269 quirks define their own .cap_mixer field but without the
static adc_nids[]. This resulted in the mismatch of ADC because ALC269
may have the widget 0x07 for another audio-in, and the auto-parser picks
this up instead.
This patch fixes the problem by adding the static adc_nids[] and co
again to these entries.
The case of address space randomization being disabled in runtime through
randomize_va_space sysctl is not treated properly in load_elf_binary(),
resulting in SIGKILL coming at exec() time for certain PIE-linked binaries
in case the randomization has been disabled at runtime prior to calling
exec().
Handle the randomize_va_space == 0 case the same way as if we were not
supporting .text randomization at all.
Based on original patch by H.J. Lu and Josh Boyer.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Ingo Molnar <mingo@elte.hu> Cc: Russell King <rmk@arm.linux.org.uk> Cc: H.J. Lu <hongjiu.lu@intel.com> Cc: <stable@kernel.org> Tested-by: Josh Boyer <jwboyer@redhat.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michel while working on the working set estimation code, noticed that
calling get_page_unless_zero() on a random pfn_to_page(random_pfn)
wasn't safe, if the pfn ended up being a tail page of a transparent
hugepage under splitting by __split_huge_page_refcount().
He then found the problem could also theoretically materialize with
page_cache_get_speculative() during the speculative radix tree lookups
that uses get_page_unless_zero() in SMP if the radix tree page is freed
and reallocated and get_user_pages is called on it before
page_cache_get_speculative has a chance to call get_page_unless_zero().
So the best way to fix the problem is to keep page_tail->_count zero at
all times. This will guarantee that get_page_unless_zero() can never
succeed on any tail page. page_tail->_mapcount is guaranteed zero and
is unused for all tail pages of a compound page, so we can simply
account the tail page references there and transfer them to
tail_page->_count in __split_huge_page_refcount() (in addition to the
head_page->_mapcount).
While debugging this s/_count/_mapcount/ change I also noticed get_page is
called by direct-io.c on pages returned by get_user_pages. That wasn't
entirely safe because the two atomic_inc in get_page weren't atomic. As
opposed to other get_user_page users like secondary-MMU page fault to
establish the shadow pagetables would never call any superflous get_page
after get_user_page returns. It's safer to make get_page universally safe
for tail pages and to use get_page_foll() within follow_page (inside
get_user_pages()). get_page_foll() is safe to do the refcounting for tail
pages without taking any locks because it is run within PT lock protected
critical sections (PT lock for pte and page_table_lock for
pmd_trans_huge).
The standard get_page() as invoked by direct-io instead will now take
the compound_lock but still only for tail pages. The direct-io paths
are usually I/O bound and the compound_lock is per THP so very
finegrined, so there's no risk of scalability issues with it. A simple
direct-io benchmarks with all lockdep prove locking and spinlock
debugging infrastructure enabled shows identical performance and no
overhead. So it's worth it. Ideally direct-io should stop calling
get_page() on pages returned by get_user_pages(). The spinlock in
get_page() is already optimized away for no-THP builds but doing
get_page() on tail pages returned by GUP is generally a rare operation
and usually only run in I/O paths.
This new refcounting on page_tail->_mapcount in addition to avoiding new
RCU critical sections will also allow the working set estimation code to
work without any further complexity associated to the tail page
refcounting with THP.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Michel Lespinasse <walken@google.com> Reviewed-by: Michel Lespinasse <walken@google.com> Reviewed-by: Minchan Kim <minchan.kim@gmail.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <jweiner@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ari got kernel panics using tg3 NIC, and bisected to 2669069aacc9 "tg3:
enable transmit time stamping."
This is because tigon3_dma_hwbug_workaround() might alloc a new skb and
free the original. We panic when skb_tx_timestamp() is called on freed
skb.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in func icmp6_dst_alloc,dst_metric_set call ipv6_cow_metrics to set metric.
ipv6_cow_metrics may will call rt6_bind_peer to set rt6_info->rt6i_peer.
So,we should move ipv6_addr_copy before dst_metric_set to make sure rt6_bind_peer success.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is bug in commit 5e2b61f(ipv4: Remove flowi from struct rtable).
It makes xfrm4_fill_dst() modify wrong data structure.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com> Reported-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
jsm uses a write queue that copies from uart_core circular buffer. This
copying however has some bugs, like not wrapping the head counter. Since
this write queue is also a circular buffer, the consumer function is
ready to use the uart_core circular buffer directly.
This buggy copying function was making some bytes be dropped when
transmitting to a raw tty, doing something like this.
Since the commit below which added O_PATH support to the *at() calls, the
error return for readlink/readlinkat for the empty pathname has switched
from ENOENT to EINVAL:
readlinkat(), fchownat() and fstatat() with empty relative pathnames
This is both unexpected for userspace and makes readlink/readlinkat
inconsistant with all other interfaces; and inconsistant with our stated
return for these pathnames.
As the readlinkat call does not have a flags parameter we cannot use the
AT_EMPTY_PATH approach used in the other calls. Therefore expose whether
the original path is infact entry via a new user_path_at_empty() path
lookup function. Use this to determine whether to default to EINVAL or
ENOENT for failures.
Addresses http://bugs.launchpad.net/bugs/817187
[akpm@linux-foundation.org: remove unused getname_flags()] Signed-off-by: Andy Whitcroft <apw@canonical.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ubd_file_size() cannot use ubd_dev->cow.file because at this time
ubd_dev->cow.file is not initialized.
Therefore, ubd_file_size() will always report a wrong disk size when
COW files are used.
Reading from /dev/ubd* would crash the kernel.
We have to read the correct disk size from the COW file's backing
file.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that Conexant CX20549 chip handle only a single input-amp even
though the audio-input widget has multiple sources. This has been never
clear, and I implemented in the current way based on the debug information
I got at the early time -- the device reacts individual input-amp values
for different sources. This is true for another Conexant codec, but it's
not applied to CX20549 actually.
This patch changes the auto-parser code to handle a single input-amp
per audio-in widget for CX20549. After applying this, you'll see only a
single "Capture" volume control instead of separate "Mic" or "Line"
captures when the device is set up to use a single ADC.
We haven't tested 20551 and 20561 codecs yet. If these show the similar
behavior like 20549, they need to set spec->single_adc_amp=1, too.
The /proc/vmallocinfo shows information about vmalloc allocations in
vmlist that is a linklist of vm_struct. It, however, may access pages
field of vm_struct where a page was not allocated. This results in a null
pointer access and leads to a kernel panic.
Why this happens: In __vmalloc_node_range() called from vmalloc(), newly
allocated vm_struct is added to vmlist at __get_vm_area_node() and then,
some fields of vm_struct such as nr_pages and pages are set at
__vmalloc_area_node(). In other words, it is added to vmlist before it is
fully initialized. At the same time, when the /proc/vmallocinfo is read,
it accesses the pages field of vm_struct according to the nr_pages field
at show_numa_info(). Thus, a null pointer access happens.
The patch adds the newly allocated vm_struct to the vmlist *after* it is
fully initialized. So, it can avoid accessing the pages field with
unallocated page when show_numa_info() is called.
Signed-off-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Rientjes <rientjes@google.com> Cc: Namhyung Kim <namhyung@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently U8500 U-Boot versions may leave the l2x0 locked down
before executing the kernel. Make sure we unlock it before we
initialize the l2x0. This fixes a performance problem reported
by Jan Rinze.
The l2x0 core has been modified to unlock the l2x0 by default,
but it will not touch the locking registers if the l2x0 was
already enabled, as on the ux500, so we need this quirk to
make sure it is properly turned off.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Rabin Vincent <rabin.vincent@stericsson.com> Cc: Adrian Bunk <adrian.bunk@movial.com> Reported-by: Jan Rinze <janrinze@gmail.com> Tested-by: Robert Marklund <robert.marklund@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix below build warning and properly set bt_reset pin.
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c: In function 'cm_x300_init_wi2wi':
arch/arm/mach-pxa/cm-x300.c:779: warning: unused variable 'wlan_en'
arch/arm/mach-pxa/cm-x300.c:795: warning: 'bt_reset' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log