which got bisected down to the stable version of this commit.
Reported-by: Jonathan Nieder <jrnieder@gmail.com> Reported-by: Phil Miller <mille121@illinois.edu> Reported-by: Philip Langdale <philipl@overt.org> Reported-by: Tim Gardner <tim.gardner@canonical.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Huawei use the product code HUAWEI_PRODUCT_E353 (0x1506) for a
number of different devices, which each can appear with a number
of different descriptor sets. Different types of interfaces
can be identified by looking at the subclass and protocol fields
Subclass 1 protocol 8 is actually the data interface of a CDC
ECM set, with subclass 1 protocol 9 as the control interface.
Neither support serial data communcation, and cannot therefore
be supported by this driver.
Found one system with UEFI/iBFT, kernel does not detect the iBFT during
iscsi_ibft module loading.
Root cause: on x86 (UEFI), we are calling of find_ibft_region() much earlier
- specifically in setup_arch() before ACPI is enabled.
Try to split acpi checking code out and call that later
At that time ACPI iBFT already get permanent mapped with ioremap.
So isa_virt_to_bus() will get wrong phys from right virt address.
We could just skip that phys address printing.
For legacy one, print the found address early.
-v2: update comments and description according to Konrad.
-v3: fix problem about module use case that is found by Konrad.
-v4: use acpi_get_table() instead of acpi_table_parse() to handle module use case that is found by Konrad again.. Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The test in fuse_file_llseek() "not SEEK_CUR or not SEEK_SET" always evaluates
to true.
This was introduced in 3.1 by commit 06222e49 (fs: handle SEEK_HOLE/SEEK_DATA
properly in all fs's that define their own llseek) and changed the behavior of
SEEK_CUR and SEEK_SET to always retrieve the file attributes. This is a
performance regression.
Fix the test so that it makes sense.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> CC: Josef Bacik <josef@redhat.com> CC: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If there is an unwritten but clean buffer in a page and there is a
dirty buffer after the buffer, then mpage_submit_io does not write the
dirty buffer out. As a result, da_writepages loops forever.
This patch fixes the problem by checking dirty flag.
If the pte mapping in generic_perform_write() is unmapped between
iov_iter_fault_in_readable() and iov_iter_copy_from_user_atomic(), the
"copied" parameter to ->end_write can be zero. ext4 couldn't cope with
it with delayed allocations enabled. This skips the i_disksize
enlargement logic if copied is zero and no new data was appeneded to
the inode.
gdb> bt
#0 0xffffffff811afe80 in ext4_da_should_update_i_disksize (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x1\
08000, len=0x1000, copied=0x0, page=0xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2467
#1 ext4_da_write_end (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x108000, len=0x1000, copied=0x0, page=0\
xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2512
#2 0xffffffff810d97f1 in generic_perform_write (iocb=<value optimized out>, iov=<value optimized out>, nr_segs=<value o\
ptimized out>, pos=0x108000, ppos=0xffff88001e26be40, count=<value optimized out>, written=0x0) at mm/filemap.c:2440
#3 generic_file_buffered_write (iocb=<value optimized out>, iov=<value optimized out>, nr_segs=<value optimized out>, p\
os=0x108000, ppos=0xffff88001e26be40, count=<value optimized out>, written=0x0) at mm/filemap.c:2482
#4 0xffffffff810db5d1 in __generic_file_aio_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=0x1, ppos=0\
xffff88001e26be40) at mm/filemap.c:2600
#5 0xffffffff810db853 in generic_file_aio_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=<value optimi\
zed out>, pos=<value optimized out>) at mm/filemap.c:2632
#6 0xffffffff811a71aa in ext4_file_write (iocb=0xffff88001e26bde8, iov=0xffff88001e26bec8, nr_segs=0x1, pos=0x108000) a\
t fs/ext4/file.c:136
#7 0xffffffff811375aa in do_sync_write (filp=0xffff88003f606a80, buf=<value optimized out>, len=<value optimized out>, \
ppos=0xffff88001e26bf48) at fs/read_write.c:406
#8 0xffffffff81137e56 in vfs_write (file=0xffff88003f606a80, buf=0x1ec2960 <Address 0x1ec2960 out of bounds>, count=0x4\
000, pos=0xffff88001e26bf48) at fs/read_write.c:435
#9 0xffffffff8113816c in sys_write (fd=<value optimized out>, buf=0x1ec2960 <Address 0x1ec2960 out of bounds>, count=0x\
4000) at fs/read_write.c:487
#10 <signal handler called>
#11 0x00007f120077a390 in __brk_reservation_fn_dmi_alloc__ ()
#12 0x0000000000000000 in ?? ()
gdb> print offset
$22 = 0xffffffffffffffff
gdb> print idx
$23 = 0xffffffff
gdb> print inode->i_blkbits
$24 = 0xc
gdb> up
#1 ext4_da_write_end (file=0xffff88003f606a80, mapping=0xffff88001d3824e0, pos=0x108000, len=0x1000, copied=0x0, page=0\
xffffea0000d792e8, fsdata=0x0) at fs/ext4/inode.c:2512
2512 if (ext4_da_should_update_i_disksize(page, end)) {
gdb> print start
$25 = 0x0
gdb> print end
$26 = 0xffffffffffffffff
gdb> print pos
$27 = 0x108000
gdb> print new_i_size
$28 = 0x108000
gdb> print ((struct ext4_inode_info *)((char *)inode-((int)(&((struct ext4_inode_info *)0)->vfs_inode))))->i_disksize
$29 = 0xd9000
gdb> down
2467 for (i = 0; i < idx; i++)
gdb> print i
$30 = 0xd44acbee
This is 100% reproducible with some autonuma development code tuned in
a very aggressive manner (not normal way even for knumad) which does
"exotic" changes to the ptes. It wouldn't normally trigger but I don't
see why it can't happen normally if the page is added to swap cache in
between the two faults leading to "copied" being zero (which then
hangs in ext4). So it should be fixed. Especially possible with lumpy
reclaim (albeit disabled if compaction is enabled) as that would
ignore the young bits in the ptes.
/proc/mounts was showing the mount option [no]init_inode_table when
the correct mount option that will be accepted by parse_options() is
[no]init_itable.
We need to make sure iocb->private is cleared *before* we put the
io_end structure on i_completed_io_list. Otherwise fsync() could
potentially run on another CPU and free the iocb structure out from
under us.
d312ae878b6a "xen: use maximum reservation to limit amount of usable RAM"
clamped the total amount of RAM to the current maximum reservation. This is
correct for dom0 but is not correct for guest domains. In order to boot a guest
"pre-ballooned" (e.g. with memory=1G but maxmem=2G) in order to allow for
future memory expansion the guest must derive max_pfn from the e820 provided by
the toolstack and not the current maximum reservation (which can reflect only
the current maximum, not the guest lifetime max). The existing algorithm
already behaves this correctly if we do not artificially limit the maximum
number of pages for the guest case.
Clement Lecigne reports a filesystem which causes a kernel oops in
hfs_find_init() trying to dereference sb->ext_tree which is NULL.
This proves to be because the filesystem has a corrupted MDB extent
record, where the extents file does not fit into the first three extents
in the file record (the first blocks).
In hfs_get_block() when looking up the blocks for the extent file
(HFS_EXT_CNID), it fails the first blocks special case, and falls
through to the extent code (which ultimately calls hfs_find_init())
which is in the process of being initialised.
Hfs avoids this scenario by always having the extents b-tree fitting
into the first blocks (the extents B-tree can't have overflow extents).
The fix is to check at mount time that the B-tree fits into first
blocks, i.e. fail if HFS_I(inode)->alloc_blocks >=
HFS_I(inode)->first_blocks
Note, the existing commit 47f365eb57573 ("hfs: fix oops on mount with
corrupted btree extent records") becomes subsumed into this as a special
case, but only for the extents B-tree (HFS_EXT_CNID), it is perfectly
acceptable for the catalog B-Tree file to grow beyond three extents,
with the remaining extent descriptors in the extents overfow.
This fixes CVE-2011-2203
Reported-by: Clement LECIGNE <clement.lecigne@netasq.com> Signed-off-by: Phillip Lougher <plougher@redhat.com> Cc: Jeff Mahoney <jeffm@suse.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I hit a J_ASSERT(blocknr != 0) failure in cleanup_journal_tail() when
mounting a fsfuzzed ext3 image. It turns out that the corrupted ext3
image has s_first = 0 in journal superblock, and the 0 is passed to
journal->j_head in journal_reset(), then to blocknr in
cleanup_journal_tail(), in the end the J_ASSERT failed.
So validate s_first after reading journal superblock from disk in
journal_get_superblock() to ensure s_first is valid.
When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.
On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.
This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.com Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The idea behind commit d91ee5863b71 ("cpuidle: replace xen access to x86
pm_idle and default_idle") was to have one call - disable_cpuidle()
which would make pm_idle not be molested by other code. It disallows
cpuidle_idle_call to be set to pm_idle (which is excellent).
But in the select_idle_routine() and idle_setup(), the pm_idle can still
be set to either: amd_e400_idle, mwait_idle or default_idle. This
depends on some CPU flags (MWAIT) and in AMD case on the type of CPU.
In case of mwait_idle we can hit some instances where the hypervisor
(Amazon EC2 specifically) sets the MWAIT and we get:
In the case of amd_e400_idle we don't get so spectacular crashes, but we
do end up making an MSR which is trapped in the hypervisor, and then
follow it up with a yield hypercall. Meaning we end up going to
hypervisor twice instead of just once.
The previous behavior before v3.0 was that pm_idle was set to
default_idle regardless of select_idle_routine/idle_setup.
We want to do that, but only for one specific case: Xen. This patch
does that.
Fixes RH BZ #739499 and Ubuntu #881076 Reported-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we can't configure the dma channel we want to fall
back to PIO. We do this by setting host->do_dma to zero.
This does not work as do_dma is used to see whether dma
can be used for the current transfer. Instead, we have
to set host->dma to NULL.
Exactly like roundup_pow_of_two(1), the rounddown version was buggy for
the case of a compile-time constant '1' argument. Probably because it
originated from the same code, sharing history with the roundup version
from before the bugfix (for that one, see commit 1a06a52ee1b0: "Fix
roundup_pow_of_two(1)").
However, unlike the roundup version, the fix for rounddown is to just
remove the broken special case entirely. It's simply not needed - the
generic code
1UL << ilog2(n)
does the right thing for the constant '1' argment too. The only reason
roundup needed that special case was because rounding up does so by
subtracting one from the argument (and then adding one to the result)
causing the obvious problems with "ilog2(0)".
But rounddown doesn't do any of that, since ilog2() naturally truncates
(ie "rounds down") to the right rounded down value. And without the
ilog2(0) case, there's no reason for the special case that had the wrong
value.
tl;dr: rounddown_pow_of_two(1) should be 1, not 0.
Prior to commit eaf35b1, cifs_save_resume_key had some NULL pointer
checks at the top. It turns out that at least one of those NULL
pointer checks is needed after all.
When the LastNameOffset in a FIND reply appears to be beyond the end of
the buffer, CIFSFindFirst and CIFSFindNext will set srch_inf.last_entry
to NULL. Since eaf35b1, the code will now oops in this situation.
Fix this by having the callers check for a NULL last entry pointer
before calling cifs_save_resume_key. No change is needed for the
call site in cifs_readdir as it's not reachable with a NULL
current_entry pointer.
Cc: Christoph Hellwig <hch@infradead.org> Reported-by: Adam G. Metzler <adamgmetzler@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Percpu allocator recorded the cpus which map to the first and last
units in pcpu_first/last_unit_cpu respectively and used them to
determine the address range of a chunk - e.g. it assumed that the
first unit has the lowest address in a chunk while the last unit has
the highest address.
This simply isn't true. Groups in a chunk can have arbitrary positive
or negative offsets from the previous one and there is no guarantee
that the first unit occupies the lowest offset while the last one the
highest.
Fix it by actually comparing unit offsets to determine cpus occupying
the lowest and highest offsets. Also, rename pcu_first/last_unit_cpu
to pcpu_low/high_unit_cpu to avoid confusion.
The chunk address range is used to flush cache on vmalloc area
map/unmap and decide whether a given address is in the first chunk by
per_cpu_ptr_to_phys() and the bug was discovered by invalid
per_cpu_ptr_to_phys() translation for crash_note.
Kudos to Dave Young for tracking down the problem.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: WANG Cong <xiyou.wangcong@gmail.com> Reported-by: Dave Young <dyoung@redhat.com> Tested-by: Dave Young <dyoung@redhat.com>
LKML-Reference: <4EC21F67.10905@redhat.com> Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A TRANSFER LENGTH field set to zero specifies that 256 logical
blocks shall be written. Any other value specifies the number
of logical blocks that shall be written.
The old code was always just returning the value in the TRANSFER LENGTH
byte. Fix this to return 256 if the byte is 0.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes iscsi-target handling of underflow where residual data is
causing an OOPs by using the incorrect iscsi_cmd_t->data_length initially
assigned in iscsit_allocate_se_cmd(). It resets iscsi_cmd_t->data_length
from se_cmd_t->data_length after transport_generic_allocate_tasks()
has been invoked in iscsit_handle_scsi_cmd() RX context, and converts
iscsi_cmd->residual_count usage to access iscsi_cmd->se_cmd.residual_count
to get the proper residual count set by target-core.
Reported-by: <lists@internyc.net> Cc: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes transport_generic_map_mem_to_cmd() to reject SCSI data
overflow and to send exception status with CHECK_CONDITION + TCM_INVALID_CDB_FIELD
for fabrics that are passing a pre-populated struct scatterlist (eg: tcm_loop
and iscsi-target) being mapped into se_cmd->t_data_sg and se_cmd->t_data_nents.
This addresses an OOPs where transport_allocate_data_tasks() would walk
the incorrect post OVERFLOW cmd->data_length value beyond the end of
the passed scatterlist.
Cc: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current tomoyo_realpath_from_path() implementation returns strange pathname
when calculating pathname of a file which belongs to lazy unmounted tree.
Use local pathname rather than strange absolute pathname in that case.
Also, this patch fixes a regression by commit 02125a82 "fix apparmor
dereferencing potentially freed dentry, sanitize __d_path() API".
__d_path() API is asking for trouble and in case of apparmor d_namespace_path()
getting just that. The root cause is that when __d_path() misses the root
it had been told to look for, it stores the location of the most remote ancestor
in *root. Without grabbing references. Sure, at the moment of call it had
been pinned down by what we have in *path. And if we raced with umount -l, we
could have very well stopped at vfsmount/dentry that got freed as soon as
prepend_path() dropped vfsmount_lock.
It is safe to compare these pointers with pre-existing (and known to be still
alive) vfsmount and dentry, as long as all we are asking is "is it the same
address?". Dereferencing is not safe and apparmor ended up stepping into
that. d_namespace_path() really wants to examine the place where we stopped,
even if it's not connected to our namespace. As the result, it looked
at ->d_sb->s_magic of a dentry that might've been already freed by that point.
All other callers had been careful enough to avoid that, but it's really
a bad interface - it invites that kind of trouble.
The fix is fairly straightforward, even though it's bigger than I'd like:
* prepend_path() root argument becomes const.
* __d_path() is never called with NULL/NULL root. It was a kludge
to start with. Instead, we have an explicit function - d_absolute_root().
Same as __d_path(), except that it doesn't get root passed and stops where
it stops. apparmor and tomoyo are using it.
* __d_path() returns NULL on path outside of root. The main
caller is show_mountinfo() and that's precisely what we pass root for - to
skip those outside chroot jail. Those who don't want that can (and do)
use d_path().
* __d_path() root argument becomes const. Everyone agrees, I hope.
* apparmor does *NOT* try to use __d_path() or any of its variants
when it sees that path->mnt is an internal vfsmount. In that case it's
definitely not mounted anywhere and dentry_path() is exactly what we want
there. Handling of sysctl()-triggered weirdness is moved to that place.
* if apparmor is asked to do pathname relative to chroot jail
and __d_path() tells it we it's not in that jail, the sucker just calls
d_absolute_path() instead. That's the other remaining caller of __d_path(),
BTW.
* seq_path_root() does _NOT_ return -ENAMETOOLONG (it's stupid anyway -
the normal seq_file logics will take care of growing the buffer and redoing
the call of ->show() just fine). However, if it gets path not reachable
from root, it returns SEQ_SKIP. The only caller adjusted (i.e. stopped
ignoring the return value as it used to do).
Reviewed-by: John Johansen <john.johansen@canonical.com> ACKed-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit f5252e00 ("mm: avoid null pointer access in vm_struct via
/proc/vmallocinfo") adds newly allocated vm_structs to the vmlist after
it is fully initialised. Unfortunately, it did not check that
__vmalloc_area_node() successfully populated the area. In the event of
allocation failure, the vmalloc area is freed but the pointer to freed
memory is inserted into the vmlist leading to a a crash later in
get_vmalloc_info().
This patch adds a check for ____vmalloc_area_node() failure within
__vmalloc_node_range. It does not use "goto fail" as in the previous
error path as a warning was already displayed by __vmalloc_area_node()
before it called vfree in its failure path.
Credit goes to Luciano Chavez for doing all the real work of identifying
exactly where the problem was.
setup_zone_migrate_reserve() expects that zone->start_pfn starts at
pageblock_nr_pages aligned pfn otherwise we could access beyond an
existing memblock resulting in the following panic if
CONFIG_HOLES_IN_ZONE is not configured and we do not check pfn_valid:
We crashed in pageblock_is_reserved() when accessing pfn 0xc0000 because
highstart_pfn = 0x36ffe.
The issue was introduced in 3.0-rc1 by 6d3163ce ("mm: check if any page
in a pageblock is reserved before marking it MIGRATE_RESERVE").
Make sure that start_pfn is always aligned to pageblock_nr_pages to
ensure that pfn_valid s always called at the start of each pageblock.
Architectures with holes in pageblocks will be correctly handled by
pfn_valid_within in pageblock_is_reserved.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Signed-off-by: Mel Gorman <mgorman@suse.de> Tested-by: Dang Bo <bdang@vmware.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Arve Hjnnevg <arve@android.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dave Hansen <dave@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit f59de89 ("lockdep: Clear whole lockdep_map on initialization"),
lockdep_init_map() will clear all the struct. But it will break
lock_set_class()/lock_set_subclass(). A typical race condition
is like below:
CPU A CPU B
lock_set_subclass(lockA);
lock_set_class(lockA);
lockdep_init_map(lockA);
/* lockA->name is cleared */
memset(lockA);
__lock_acquire(lockA);
/* lockA->class_cache[] is cleared */
register_lock_class(lockA);
look_up_lock_class(lockA);
WARN_ON_ONCE(class->name !=
lock->name);
lock->name = name;
So restore to what we have done before commit f59de89 but annotate
->lock with kmemcheck_mark_initialized() to suppress the kmemcheck
warning reported in commit f59de89.
Commit 70b50f94f1644 ("mm: thp: tail page refcounting fix") keeps all
page_tail->_count zero at all times. But the current kernel does not
set page_tail->_count to zero if a 1GB page is utilized. So when an
IOMMU 1GB page is used by KVM, it wil result in a kernel oops because a
tail page's _count does not equal zero.
With the 3.2-rc kernel, IOMMU 2M pages in KVM works. But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.
The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd. If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.
So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.
This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.
Allow userspace applications to do more parameter setting by providing a
more complete stub DMA driver specifying a wildcard set of formats and
channels and essentially random values for the DMA parameters. This is
required for useful runtime operation of the dummy DMA driver until we
are able to figure out how to power up links and do hw_params() from DAPM.
Sending to stable as without this the dummy driver is not terribly
useful.
Reported-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com> Tested-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function setup_vpif_input_channel_mode() used the VSCLKDIS register
instead of VIDCLKCTL. This meant that when in HD mode videoport channel 0
used a different clock from channel 1.
Clearly a copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since 193ab2a6070039e7ee2b9b9bebea754a7c52fd1b, various AT91 boards don't
register at91_udc anymore due to depending on a now non-existing symbol.
Fix the symbol name.
Signed-off-by: Anders Darander <anders@chargestorm.se> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OMAP-L138 platform, EDMA event queue 0 should be used for audio
transfers so that they are not starved by video data moving on event queue 1.
Commit 48519f0ae03bc7e86b3dc93e56f1334d53803770 (ASoC: davinci: let platform
data define edma queue numbers) had a side-effect of changing this behavior
by making the driver actually honor the platform data passed.
Fix this now by passing event queue 0 as the queue to be used for audio
transfers.
The expiry function compares the timer against current time and does
not expire the timer when the expiry time is >= now. That's wrong. If
the timer is set for now, then it must expire.
Make the condition expiry > now for breaking out the loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some HP laptops with IDT 92HD75 codecs may use a GPIO > 4 for the mute
LED, but currently the driver doesn't check this properly, and confuses
the mute LED behavior. This ended up with the silent output on some
HP laptops due to having another GPIO used as external amp control.
This patch fixes the problem by checking the max GPIO count and
comparing with the given value from DMI entry instead of magic fixed
value 4 and 8, and adding a new field to indicate the VREF mute-LED
behavior.
When no imux is available (e.g. a single capture source),
alc_auto_init_input_src() may trigger an Oops due to the access to -1.
Add a proper zero-check to avoid it.
There are some AC97 codec and board combinations that have been observed
to take a very long time to respond after the cold reset has completed.
In one case, more than 350 ms was required. To allow users to have sound
on those platforms, we'll wait up to 500ms for the codec to become
ready.
As a board may have multiple codecs, with some faster than others to
reset, we add a module parameter to inform the driver which codecs
should be present.
Le mercredi 30 novembre 2011 à 14:36 -0800, Stephen Hemminger a écrit :
> (Almost) nobody uses RED because they can't figure it out.
> According to Wikipedia, VJ says that:
> "there are not one, but two bugs in classic RED."
RED is useful for high throughput routers, I doubt many linux machines
act as such devices.
I was considering adding Adaptative RED (Sally Floyd, Ramakrishna
Gummadi, Scott Shender), August 2001
In this version, maxp is dynamic (from 1% to 50%), and user only have to
setup min_th (target average queue size)
(max_th and wq (burst in linux RED) are automatically setup)
By the way it seems we have a small bug in red_change()
if (skb_queue_empty(&sch->q))
red_end_of_idle_period(&q->parms);
First, if queue is empty, we should call
red_start_of_idle_period(&q->parms);
Second, since we dont use anymore sch->q, but q->qdisc, the test is
meaningless.
Oh well...
[PATCH] sch_red: fix red_change()
Now RED is classful, we must check q->qdisc->q.qlen, and if queue is empty,
we start an idle period, not end it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit a4a710c4a7490587 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.
red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.
Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__mkroute_output fails to work with the original tos
and uses value with stripped RTO_ONLINK bit. Make sure we put
the original TOS bits into rt_key_tos because it used to match
cached route.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now inetpeer is the place where we cache redirect information for ipv4
destinations, we must be able to invalidate informations when a route is
added/removed on host.
As inetpeer is not yet namespace aware, this patch adds a shared
redirect_genid, and a per inetpeer redirect_genid. This might be changed
later if inetpeer becomes ns aware.
Cache information for one inerpeer is valid as long as its
redirect_genid has the same value than global redirect_genid.
Reported-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com> Tested-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f39925dbde77 (ipv4: Cache learned redirect information in
inetpeer.) introduced a regression in ICMP redirect handling.
It assumed ipv4_dst_check() would be called because all possible routes
were attached to the inetpeer we modify in ip_rt_redirect(), but thats
not true.
commit 7cc9150ebe (route: fix ICMP redirect validation) tried to fix
this but solution was not complete. (It fixed only one route)
So we must lookup existing routes (including different TOS values) and
call check_peer_redir() on them.
Reported-by: Ivan Zahariev <famzah@icdsoft.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit f39925dbde7788cfb96419c0f092b086aa325c0f
(ipv4: Cache learned redirect information in inetpeer.)
removed some ICMP packet validations which are required by
RFC 1122, section 3.2.2.2:
...
A Redirect message SHOULD be silently discarded if the new
gateway address it specifies is not on the same connected
(sub-) net through which the Redirect arrived [INTRO:2,
Appendix A], or if the source of the Redirect is not the
current first-hop gateway for the specified destination (see
Section 3.3.1).
Signed-off-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In func ipv4_dst_check,check_peer_pmtu should be called only when peer is updated.
So,if the peer is not updated in ip_rt_frag_needed,we can not inc __rt_peer_genid.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need rcu_read_lock() protection before using dst_get_neighbour(), and
we must cache its value (pass it to __teql_resolve())
teql_master_xmit() is called under rcu_read_lock_bh() protection, its
not enough.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit f2c31e32b378 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When opt->srr_is_hit is set skb_rtable(skb) has been updated for
'nexthop' and iph->daddr should always equals to skb_rtable->rt_dst
holds, We need update iph->daddr either.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The AH4/6 ahash input callbacks read out the nexthdr field from the AH
header *after* they overwrite that header. This is obviously not going
to end well. Fix it up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The AH4/6 ahash output callbacks pass nexthdr to xfrm_output_resume
instead of the error code. This appears to be a copy+paste error from
the input case, where nexthdr is expected. This causes the driver to
continuously add AH headers to the datagram until either an allocation
fails and the packet is dropped or the ahash driver hits a synchronous
fallback and the resulting monstrosity is transmitted.
Correct this issue by simply passing the error code unadulterated.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device is shutdown, then there might be a pending interrupt,
which will be processed after we reenable interrupts, which causes the
original handler to be run. If the old handler is the (broadcast)
periodic handler the shutdown state might hang the kernel completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oprofile may crash in a KVM guest while unlaoding modules. This
happens if oprofile_arch_init() fails and oprofile switches to the hr
timer mode as a fallback. In this case oprofile_arch_exit() is called,
but it never was initialized properly which causes the crash. This
patch fixes this.
oprofile: using timer interrupt.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8123c226>] unregister_syscore_ops+0x41/0x58
PGD 41da3f067 PUD 41d80e067 PMD 0
Oops: 0002 [#1] PREEMPT SMP
CPU 5
Modules linked in: oprofile(-)
If cpu A calls jump_label_inc() just after atomic_add_return() is
called by cpu B, atomic_inc_not_zero() will return value greater then
zero and jump_label_inc() will return to a caller before jump_label_update()
finishes its job on cpu B.
Link: http://lkml.kernel.org/r/20111018175551.GH17571@redhat.com Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A update is made to the sched:sched_switch event that adds some
logic to the first parameter of the __print_flags() that shows the
state of tasks. This change cause perf to fail parsing the flags.
A simple fix is needed to have the parser be able to process ops
within the argument.
Reported-by: Andrew Vagin <avagin@openvz.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a bug introduced by e9dbfae5, which prevents event_subsystem from
ever being released.
Ref_count was added to keep track of subsystem users, not for counting
events. Subsystem is created with ref_count = 1, so there is no need to
increment it for every event, we have nr_events for that. Fix this by
touching ref_count only when we actually have a new user -
subsystem_open().
The current code checks if abs(delta_delta.tv_sec) is greater or
equal to two before it discards the old delta value, but this can
trigger at close to -1 seconds since -1.000000001 seconds is stored
as tv_sec -2 and tv_nsec 999999999 in a normalized timespec.
rtc_resume had an early return check if the rtc value had not changed
since rtc_suspend. This effectivly stops time for the duration of the
short sleep. Check if sleep_time is positive after all the adjustments
have been applied instead since this allows the old_system adjustment
in rtc_suspend to have an effect even for short sleep cycles.
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
A forced undef of a config value was used for testing and was
accidently left in during the final commit. This causes x86 to
run slower than needed while running function tracing as well
as causes the function graph selftest to fail when DYNMAIC_FTRACE
is not set. This is because the code in MCOUNT expects the ftrace
code to be processed with the config value set that happened to
be forced not set.
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 30765b92 ("slab, lockdep: Annotate the locks before using
them") moves the init_lock_keys() call from after g_cpucache_up =
FULL, to before it. And overlooks the fact that init_node_lock_keys()
tests for it and ignores everything !FULL.
Introduce a LATE stage and change the lockdep test to be <LATE.
Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In irq_wait_for_interrupt(), the should_stop member is verified before
setting the task's state to TASK_INTERRUPTIBLE and calling schedule().
In case kthread_stop sets should_stop and wakes up the process after
should_stop is checked by the irq thread but before the task's state
is changed, the irq thread might never exit:
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If addBA responses comes in just after addba_resp_timer has
expired mac80211 will still accept it and try to open the
aggregation session. This causes drivers to be confused and
in some cases even crash.
This patch fixes the race condition and makes sure that if
addba_resp_timer has expired addBA response is not longer
accepted and we do not try to open half-closed session.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
[some adjustments] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last breaking event address is a read-only value, the regset misses the
.set function. If a PTRACE_SETREGSET is done for NT_S390_LAST_BREAK we
get an oops due to a branch to zero:
If oprofile uses the nmi timer interrupt there is a crash while
unloading the module. The bug can be triggered with oprofile build as
module and kernel parameter nolapic set. This patch fixes this.
oprofile: using NMI timer interrupt.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8123c226>] unregister_syscore_ops+0x41/0x58
PGD 42dbca067 PUD 41da6a067 PMD 0
Oops: 0002 [#1] PREEMPT SMP
CPU 5
Modules linked in: oprofile(-) [last unloaded: oprofile]
Masami spotted that we always try to decode the instruction stream as
64bit instructions when running a 64bit kernel, this doesn't work for
ia32-compat proglets.
Use TIF_IA32 to detect if we need to use the 32bit instruction
decoder.
The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:
map = kmap_atomic(page, KM_USER0) + offset;
and then later we touch *map.
Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.
Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.
Interestingly, commit b8bcfe997e4615 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails. It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).
There's a log of problems at:
https://bbs.archlinux.org/viewtopic.php?id=124136
This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: Uroš Vampl <mobile.leecher@gmail.com> Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au> Cc: Don Zickus <dzickus@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.com Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit f8924e770e04 ("x86: unify mp_bus_info"), the 32-bit
and 64-bit versions of MP_bus_info were rearranged to match each
other better. Unfortunately it introduced a regression: prior
to that change we used to always set the mp_bus_not_pci bit,
then clear it if we found a PCI bus. After it, we set
mp_bus_not_pci for ISA buses, clear it for PCI buses, and leave
it alone otherwise.
In the cases of ISA and PCI, there's not much difference. But
ISA is not the only non-PCI bus, so it's better to always set
mp_bus_not_pci and clear it only for PCI.
Without this change, Dan's Dell PowerEdge 4200 panics on boot
with a log indicating interrupt routing trouble unless the
"noapic" option is supplied. With this change, the machine
boots reliably without "noapic".
In hundreds of days, the __cycles_2_ns calculation in sched_clock
has an overflow. cyc * per_cpu(cyc2ns, cpu) exceeds 64 bits, causing
the final value to become zero. We can solve this without losing
any precision.
We can decompose TSC into quotient and remainder of division by the
scale factor, and then use this to convert TSC into nanoseconds.
Signed-off-by: Salman Qazi <sqazi@google.com> Acked-by: John Stultz <johnstul@us.ibm.com> Reviewed-by: Paul Turner <pjt@google.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20111115221121.7262.88871.stgit@dungbeetle.mtv.corp.google.com Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When system enters suspend, xHCI driver clears command ring by writing zero
to all the TRBs. However, this also writes zero to the Link TRB, and the ring
is mangled. This may cause driver accesses wrong memory address and the
result is unpredicted.
When clear the command ring, keep the last Link TRB intact, only clear its
cycle bit. This should fix the "command ring full" issue reported by Oliver
Neukum.
This should be backported to stable kernels as old as 2.6.37, since the
commit 89821320 "xhci: Fix command ring replay after resume" is merged.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
projects / karo-tx-linux.git / log