vt6656 has several headers that use the #pragma pack(1) directive to
enable structure packing, but never disable it. The layout of
structures defined in other headers can then depend on which order the
various headers are included in, breaking the One Definition Rule.
In practice this resulted in crashes on x86_64 until the order of header
inclusion was changed for some files in commit 11d404cb56ecd ('staging:
vt6656: fix headers and add cfg80211.'). But we need a proper fix that
won't be affected by future changes to the order of inclusion.
This removes the #pragma pack(1) directives and adds __packed to the
structure definitions for which packing appears to have been intended.
Commit 2e254212 broke listing of available network names, since it
clamped the length of the returned SSID to WLAN_BSSID_LEN (6) instead of
WLAN_SSID_MAXLEN (32).
When shut down SPI port, it's possible that MRDY has been asserted and a SPI
timer was activated waiting for SRDY assert, in the case, it needs to delete
this timer.
There has been an error on the xen_failsafe_callback path for failed
iret, which causes the stack pointer to be wrong when entering the
iret_exc error path. This can result in the kernel crashing.
In the classic kernel case, the relevant code looked a little like:
popl %eax # Error code from hypervisor
jz 5f
addl $16,%esp
jmp iret_exc # Hypervisor said iret fault
5: addl $16,%esp
# Hypervisor said segment selector fault
Here, there are two identical addls on either option of a branch which
appears to have been optimised by hoisting it above the jz, and
converting it to an lea, which leaves the flags register unaffected.
In the PVOPS case, the code looks like:
popl_cfi %eax # Error from the hypervisor
lea 16(%esp),%esp # Add $16 before choosing fault path
CFI_ADJUST_CFA_OFFSET -16
jz 5f
addl $16,%esp # Incorrectly adjust %esp again
jmp iret_exc
It is possible unprivileged userspace applications to cause this
behaviour, for example by loading an LDT code selector, then changing
the code selector to be not-present. At this point, there is a race
condition where it is possible for the hypervisor to return back to
userspace from an interrupt, fault on its own iret, and inject a
failsafe_callback into the kernel.
This bug has been present since the introduction of Xen PVOPS support
in commit 5ead97c84 (xen: Core Xen implementation), in 2.6.23.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com> Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 85ff6acb075a484780b3d763fdf41596d8fc0970 (xen/granttable: Grant
tables V2 implementation) changed the GREFS_PER_GRANT_FRAME macro from
a constant to a conditional expression. The expression depends on
grant_table_version being appropriately set. Unfortunately, at init
time grant_table_version will be 0. The GREFS_PER_GRANT_FRAME
conditional expression checks for "grant_table_version == 1", and
therefore returns the number of grant references per frame for v2.
This causes gnttab_init() to allocate fewer pages for gnttab_list, as
a frame can old half the number of v2 entries than v1 entries. After
gnttab_resume() is called, grant_table_version is appropriately
set. nr_init_grefs will then be miscalculated and gnttab_free_count
will hold a value larger than the actual number of free gref entries.
If a guest is heavily utilizing improperly initialized v1 grant
tables, memory corruption can occur. One common manifestation is
corruption of the vmalloc list, resulting in a poisoned pointer
derefrence when accessing /proc/meminfo or /proc/vmallocinfo:
[ 40.770064] BUG: unable to handle kernel paging request at 0000200200001407
[ 40.770083] IP: [<ffffffff811a6fb0>] get_vmalloc_info+0x70/0x110
[ 40.770102] PGD 0
[ 40.770107] Oops: 0000 [#1] SMP
[ 40.770114] CPU 10
This patch introduces a static variable, grefs_per_grant_frame, to
cache the calculated value. gnttab_init() now calls
gnttab_request_version() early so that grant_table_version and
grefs_per_grant_frame can be appropriately set. A few BUG_ON()s have
been added to prevent this type of bug from reoccurring in the future.
Signed-off-by: Matt Wilson <msw@amazon.com> Reviewed-and-Tested-by: Steven Noonan <snoonan@amazon.com> Acked-by: Ian Campbell <Ian.Campbell@citrix.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Annie Li <annie.li@oracle.com> Cc: xen-devel@lists.xen.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During MSI-X setup the system might run out of vectors. If this happens the
already assigned vectors for this NIC should be freed before trying the
disable MSI-X. Failing to do so results in the following oops.
This patch is to prevent non-USB devices that have RMRRs associated with them from
being placed into the SI Domain during init. This fixes the issue where the RMRR info
for devices being placed in and out of the SI Domain gets lost.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Reviewed-by: Donald Dutile <ddutile@redhat.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds [dev,lun]_link_magic value assignment + checks within generic
target_fabric_port_link() and target_fabric_mappedlun_link() code to ensure
destination config_item *target_item sent from configfs_symlink() ->
config_item_operations->allow_link() is the underlying se_device->dev_group
and se_lun->lun_group that we expect to symlink.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reworking the r8169 driver a few months ago to perform the
smallest amount of work in the irq handler, I took care of avoiding
any irq mask register operation in the slow work dedicated user
context thread. The slow work thread scheduled an extra round of NAPI
work which would ultimately set the irq mask register as required,
thus keeping such irq mask operations in the NAPI handler.
It would eventually race with the irq handler and delay NAPI execution
for - assuming no further irq - a whole ksoftirqd period. Mildly a
problem for rare link changes or corner case PCI events.
The race was always lost after the last bh disabling lock had been
removed from the work thread and people started wondering where those
pesky "NOHZ: local_softirq_pending 08" messages came from.
Actually the irq mask register _can_ be set up directly in the slow
work thread.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Reported-by: Dave Jones <davej@redhat.com> Tested-by: Marc Dionne <marc.c.dionne@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SNB graphics devices have a bug that prevent them from accessing certain
memory ranges, namely anything below 1M and in the pages listed in the
table. So reserve those at boot if set detect a SNB gfx device on the
CPU to avoid GPU hangs.
Stephane Marchesin had a similar patch to the page allocator awhile
back, but rather than reserving pages up front, it leaked them at
allocation time.
[ hpa: made a number of stylistic changes, marked arrays as static
const, and made less verbose; use "memblock=debug" for full
verbosity. ]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Converting a 64 Bit TOD format value to nanoseconds means that the value
must be divided by 4.096. In order to achieve that we multiply with 125
and divide by 512.
When used within sched_clock() this triggers an overflow after appr.
417 days. Resulting in a sched_clock() return value that is much smaller
than previously and therefore may cause all sort of weird things in
subsystems that rely on a monotonic sched_clock() behaviour.
To fix this implement a tod_to_ns() helper function which converts TOD
values without overflow and call this function from both places that
open coded the conversion: sched_clock() and kvm_s390_handle_wait().
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transport_lookup_tmr_lun() fails and we return a task management
response from target_complete_tmr_failure(), we need to call
transport_cmd_check_stop_to_fabric() to release the last ref to the
cmd after calling se_tfo->queue_tm_rsp(), or else we will never remove
the failed TMR from the session command list (and we'll end up waiting
forever when trying to tear down the session).
(nab: Fix minor compile breakage)
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear the target role when no target is provided for
the node performing a PRLI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generating a PRLI response to an initiator, clear the
FCP_SPPF_RETRY bit in the response.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the aux table is properly initialized, even when optional features
are missing. Without this, the FDPIC loader did not work. This was meant to
be included in commit d5ab780305bb6d60a7b5a74f18cf84eb6ad153b1.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller. The controller needs to
be told to disable the endpoints that have been enabled for the new
config. The existing code does this, but before storing the
information about which endpoints were enabled! As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.
The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config. If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble. The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ni_at_a2150' module links to `cfc_write_to_buffer` in the
'comedi_fc' module, so selecting 'COMEDI_NI_AT_A2150' in the kernel config
needs to also select 'COMEDI_FC'.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
comedi_auto_config() associates a Comedi minor device number with an
auto-configured hardware device and comedi_auto_unconfig() disassociates
it. Currently, these use the hardware device's private data pointer to
point to some allocated storage holding the minor device number. This
is a bit of a waste of the hardware device's private data pointer,
preventing it from being used for something more useful by the low-level
comedi device drivers. For example, it would make more sense if
comedi_usb_auto_config() was passed a pointer to the struct
usb_interface instead of the struct usb_device, but this cannot be done
currently because the low-level comedi drivers already use the private
data pointer in the struct usb_interface for something more useful.
This patch stops the comedi core hijacking the hardware device's private
data pointer. Instead, comedi_auto_config() stores a pointer to the
hardware device's struct device in the struct comedi_device_file_info
associated with the minor device number, and comedi_auto_unconfig()
calls new function comedi_find_board_minor() to recover the minor device
number associated with the hardware device.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yan, Zheng [Mon, 19 Nov 2012 02:49:09 +0000 (10:49 +0800)]
ceph: call handle_cap_grant() for cap import message
If client sends cap message that requests new max size during
exporting caps, the exporting MDS will drop the message quietly.
So the client may wait for the reply that updates the max size
forever. call handle_cap_grant() for cap import message can
avoid this issue.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com> Signed-off-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 0e5e1774a92e6fe9c511585de8f078b4c4c68dbb) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yan, Zheng [Mon, 19 Nov 2012 02:49:06 +0000 (10:49 +0800)]
ceph: Fix infinite loop in __wake_requests
__wake_requests() will enter infinite loop if we use it to wake
requests in the session->s_waiting list. __wake_requests() deletes
requests from the list and __do_request() adds requests back to
the list.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com> Signed-off-by: Sage Weil <sage@inktank.com>
(cherry picked from commit ed75ec2cd19b47efcd292b6e23f58e56f4c5bc34) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Fri, 16 Nov 2012 15:29:16 +0000 (09:29 -0600)]
rbd: do not allow remove of mounted-on image
There is no check in rbd_remove() to see if anybody holds open the
image being removed. That's not cool.
Add a simple open count that goes up and down with opens and closes
(releases) of the device, and don't allow an rbd image to be removed
if the count is non-zero.
Protect the updates of the open count value with ctl_mutex to ensure
the underlying rbd device doesn't get removed while concurrently
being opened.
Alex Elder [Thu, 11 Oct 2012 04:19:13 +0000 (21:19 -0700)]
rbd: fix bug in rbd_dev_id_put()
In rbd_dev_id_put(), there's a loop that's intended to determine
the maximum device id in use. But it isn't doing that at all,
the effect of how it's written is to simply use the just-put id
number, which ignores whole purpose of this function.
Fix the bug.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
(cherry picked from commit b213e0b1a62637b2a9395a34349b13d73ca2b90a) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Thu, 6 Dec 2012 15:37:23 +0000 (09:37 -0600)]
rbd: remove linger unconditionally
In __unregister_linger_request(), the request is being removed
from the osd client's req_linger list only when the request
has a non-null osd pointer. It should be done whether or not
the request currently has an osd.
This is most likely a non-issue because I believe the request
will always have an osd when this function is called.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 61c74035626beb25a39b0273ccf7d75510bc36a1) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Thu, 29 Nov 2012 14:37:03 +0000 (08:37 -0600)]
ceph: don't reference req after put
In __unregister_request(), there is a call to list_del_init()
referencing a request that was the subject of a call to
ceph_osdc_put_request() on the previous line. This is not
safe, because the request structure could have been freed
by the time we reach the list_del_init().
Fix this by reversing the order of these lines.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-off-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 7d5f24812bd182a2471cb69c1c2baf0648332e1f) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sage Weil [Wed, 28 Nov 2012 20:28:24 +0000 (12:28 -0800)]
libceph: remove 'osdtimeout' option
This would reset a connection with any OSD that had an outstanding
request that was taking more than N seconds. The idea was that if the
OSD was buggy, the client could compensate by resending the request.
In reality, this only served to hide server bugs, and we haven't
actually seen such a bug in quite a while. Moreover, the userspace
client code never did this.
More importantly, often the request is taking a long time because the
OSD is trying to recover, or overloaded, and killing the connection
and retrying would only make the situation worse by giving the OSD
more work to do.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit 83aff95eb9d60aff5497e9f44a2ae906b86d8e88) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Fri, 10 Aug 2012 20:12:07 +0000 (13:12 -0700)]
rbd: add read_only rbd map option
Add the ability to map an rbd image read-only, by specifying either
"read_only" or "ro" as an option on the rbd "command line." Also
allow the inverse to be explicitly specified using "read_write" or
"rw".
Right now the kernel still has one piece of rbd management
duplicated from the rbd command line tool: snapshot creation.
There's nothing special about snapshot creation that makes it
advantageous to do from the kernel, so I'd like to remove the
create_snap sysfs interface. That is,
/sys/bus/rbd/devices/<id>/create_snap
would be removed.
Does anyone rely on the sysfs interface for creating rbd
snapshots? If so, how hard would it be to replace with:
rbd snap create pool/image@snap
Is there any benefit to the sysfs interface that I'm missing?
Josh
This patch implements this proposal, removing the code that
implements the "snap_create" sysfs interface for rbd images.
As a result, quite a lot of other supporting code goes away.
[elder@inktank.com: commented out rbd_req_sync_exec() to avoid warning]
Suggested-by: Josh Durgin <josh.durgin@inktank.com> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
(based on commit 02cdb02ceab1f3dd9ac2bc899fc51f0e0e744782)
Alex Elder [Fri, 7 Dec 2012 15:57:58 +0000 (09:57 -0600)]
libceph: avoid using freed osd in __kick_osd_requests()
If an osd has no requests and no linger requests, __reset_osd()
will just remove it with a call to __remove_osd(). That drops
a reference to the osd, and therefore the osd may have been free
by the time __reset_osd() returns. That function offers no
indication this may have occurred, and as a result the osd will
continue to be used even when it's no longer valid.
Change__reset_osd() so it returns an error (ENODEV) when it
deletes the osd being reset. And change __kick_osd_requests() so it
returns immediately (before referencing osd again) if __reset_osd()
returns *any* error.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 685a7555ca69030739ddb57a47f0ea8ea80196a4) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sage Weil [Mon, 29 Oct 2012 18:01:42 +0000 (11:01 -0700)]
libceph: fix osdmap decode error paths
Ensure that we set the err value correctly so that we do not pass a 0
value to ERR_PTR and confuse the calling code. (In particular,
osd_client.c handle_map() will BUG(!newmap)).
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit 0ed7285e0001b960c888e5455ae982025210ed3d) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not set con->state to CLOSED here; that happens in
ceph_fault() in the caller, where it first asserts that the state
is not yet CLOSED. Avoids a BUG when the features don't match.
Since the fail_protocol() has become a trivial wrapper, replace
calls to it with direct calls to reset_connection().
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit 0fa6ebc600bc8e830551aee47a0e929e818a1868) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Wed, 26 Dec 2012 16:43:57 +0000 (10:43 -0600)]
libceph: WARN, don't BUG on unexpected connection states
A number of assertions in the ceph messenger are implemented with
BUG_ON(), killing the system if connection's state doesn't match
what's expected. At this point our state model is (evidently) not
well understood enough for these assertions to trigger a BUG().
Convert all BUG_ON(con->state...) calls to be WARN_ON(con->state...)
so we learn about these issues without killing the machine.
We now recognize that a connection fault can occur due to a socket
closure at any time, regardless of the state of the connection. So
there is really nothing we can assert about the state of the
connection at that point so eliminate that assertion.
Reported-by: Ugis <ugis22@gmail.com> Tested-by: Ugis <ugis22@gmail.com> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 122070a2ffc91f87fe8e8493eb0ac61986c5557c) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Wed, 26 Dec 2012 20:31:40 +0000 (14:31 -0600)]
libceph: always reset osds when kicking
When ceph_osdc_handle_map() is called to process a new osd map,
kick_requests() is called to ensure all affected requests are
updated if necessary to reflect changes in the osd map. This
happens in two cases: whenever an incremental map update is
processed; and when a full map update (or the last one if there is
more than one) gets processed.
In the former case, the kick_requests() call is followed immediately
by a call to reset_changed_osds() to ensure any connections to osds
affected by the map change are reset. But for full map updates
this isn't done.
Both cases should be doing this osd reset.
Rather than duplicating the reset_changed_osds() call, move it into
the end of kick_requests().
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit e6d50f67a6b1a6252a616e6e629473b5c4277218) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Wed, 19 Dec 2012 21:52:36 +0000 (15:52 -0600)]
libceph: move linger requests sooner in kick_requests()
The kick_requests() function is called by ceph_osdc_handle_map()
when an osd map change has been indicated. Its purpose is to
re-queue any request whose target osd is different from what it
was when it was originally sent.
It is structured as two loops, one for incomplete but registered
requests, and a second for handling completed linger requests.
As a special case, in the first loop if a request marked to linger
has not yet completed, it is moved from the request list to the
linger list. This is as a quick and dirty way to have the second
loop handle sending the request along with all the other linger
requests.
Because of the way it's done now, however, this quick and dirty
solution can result in these incomplete linger requests never
getting re-sent as desired. The problem lies in the fact that
the second loop only arranges for a linger request to be sent
if it appears its target osd has changed. This is the proper
handling for *completed* linger requests (it avoids issuing
the same linger request twice to the same osd).
But although the linger requests added to the list in the first loop
may have been sent, they have not yet completed, so they need to be
re-sent regardless of whether their target osd has changed.
The first required fix is we need to avoid calling __map_request()
on any incomplete linger request. Otherwise the subsequent
__map_request() call in the second loop will find the target osd
has not changed and will therefore not re-send the request.
Second, we need to be sure that a sent but incomplete linger request
gets re-sent. If the target osd is the same with the new osd map as
it was when the request was originally sent, this won't happen.
This can be fixed through careful handling when we move these
requests from the request list to the linger list, by unregistering
the request *before* it is registered as a linger request. This
works because a side-effect of unregistering the request is to make
the request's r_osd pointer be NULL, and *that* will ensure the
second loop actually re-sends the linger request.
Processing of such a request is done at that point, so continue with
the next one once it's been moved.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit ab60b16d3c31b9bd9fd5b39f97dc42c52a50b67d) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Thu, 6 Dec 2012 13:22:04 +0000 (07:22 -0600)]
libceph: register request before unregister linger
In kick_requests(), we need to register the request before we
unregister the linger request. Otherwise the unregister will
reset the request's osd pointer to NULL.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit c89ce05e0c5a01a256100ac6a6019f276bdd1ca6) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Mon, 17 Dec 2012 18:23:48 +0000 (12:23 -0600)]
libceph: don't use rb_init_node() in ceph_osdc_alloc_request()
The red-black node in the ceph osd request structure is initialized
in ceph_osdc_alloc_request() using rbd_init_node(). We do need to
initialize this, because in __unregister_request() we call
RB_EMPTY_NODE(), which expects the node it's checking to have
been initialized. But rb_init_node() is apparently overkill, and
may in fact be on its way out. So use RB_CLEAR_NODE() instead.
For a little more background, see this commit: 4c199a93 rbtree: empty nodes have no color"
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit a978fa20fb657548561dddbfb605fe43654f0825) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Mon, 17 Dec 2012 18:23:48 +0000 (12:23 -0600)]
libceph: init event->node in ceph_osdc_create_event()
The red-black node node in the ceph osd event structure is not
initialized in create_osdc_create_event(). Because this node can
be the subject of a RB_EMPTY_NODE() call later on, we should ensure
the node is initialized properly for that.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 3ee5234df68d253c415ba4f2db72ad250d9c21a9) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Thu, 6 Dec 2012 13:22:04 +0000 (07:22 -0600)]
libceph: init osd->o_node in create_osd()
The red-black node node in the ceph osd structure is not initialized
in create_osd(). Because this node can be the subject of a
RB_EMPTY_NODE() call later on, we should ensure the node is
initialized properly for that. Add a call to RB_CLEAR_NODE()
initialize it.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit f407731d12214e7686819018f3a1e9d7b6f83a02) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Fri, 14 Dec 2012 22:47:41 +0000 (16:47 -0600)]
libceph: report connection fault with warning
When a connection's socket disconnects, or if there's a protocol
error of some kind on the connection, a fault is signaled and
the connection is reset (closed and reopened, basically). We
currently get an error message on the log whenever this occurs.
A ceph connection will attempt to reestablish a socket connection
repeatedly if a fault occurs. This means that these error messages
will get repeatedly added to the log, which is undesirable.
Change the error message to be a warning, so they don't get
logged by default.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 28362986f8743124b3a0fda20a8ed3e80309cce1) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Elder [Sat, 8 Dec 2012 01:50:07 +0000 (19:50 -0600)]
libceph: socket can close in any connection state
A connection's socket can close for any reason, independent of the
state of the connection (and without irrespective of the connection
mutex). As a result, the connectino can be in pretty much any state
at the time its socket is closed.
Handle those other cases at the top of con_work(). Pull this whole
block of code into a separate function to reduce the clutter.
Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
(cherry picked from commit 7bb21d68c535ad8be38e14a715632ae398b37ac1) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sage Weil [Tue, 25 Sep 2012 04:01:02 +0000 (21:01 -0700)]
ceph: propagate layout error on osd request creation
If we are creating an osd request and get an invalid layout, return
an EINVAL to the caller. We switch up the return to have an error
code instead of NULL implying -ENOMEM.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit 6816282dab3a72efe8c0d182c1bc2960d87f4322) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josh Durgin [Mon, 5 Dec 2011 22:03:05 +0000 (14:03 -0800)]
rbd: use reference counting for the snap context
This prevents a race between requests with a given snap context and
header updates that free it. The osd client was already expecting the
snap context to be reference counted, since it get()s it in
ceph_osdc_build_request and put()s it when the request completes.
Also remove the second down_read()/up_read() on header_rwsem in
rbd_do_request, which wasn't actually preventing this race or
protecting any other data.
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com> Reviewed-by: Alex Elder <elder@inktank.com>
(cherry picked from commit d1d25646543134d756a02ffe4e02073faa761f2c) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josh Durgin [Tue, 22 Nov 2011 02:14:25 +0000 (18:14 -0800)]
rbd: return errors for mapped but deleted snapshot
When a snapshot is deleted, the OSD will return ENOENT when reading
from it. This is normally interpreted as a hole by rbd, which will
return zeroes. To minimize the time in which this can happen, stop
requests early when we are notified that our snapshot no longer
exists.
Sage Weil [Mon, 30 Jul 2012 23:21:17 +0000 (16:21 -0700)]
ceph: close old con before reopening on mds reconnect
When we detect a mds session reset, close the old ceph_connection before
reopening it. This ensures we clean up the old socket properly and keep
the ceph_connection state correct.
Signed-off-by: Sage Weil <sage@inktank.com> Reviewed-by: Alex Elder <elder@inktank.com> Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
(cherry picked from commit a53aab645c82f0146e35684b34692c69b5118121) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was meant to be the purpose of the
intel_crtc_wait_for_pending_flips() function which is called whilst
preparing the CRTC for a modeset or before disabling. However, as Ville
Syrjala pointed out, we set the pending flip notification on the old
framebuffer that is no longer attached to the CRTC by the time we come
to flush the pending operations. Instead, we can simply wait on the
pending unpin work to be finished on this CRTC, knowning that the
hardware has therefore finished modifying the registers, before proceeding
with our direct access.
Fixes i-g-t/flip_test on non-pch platforms. pch platforms simply
schedule the flip immediately when the pipe is disabled, leading
to other funny issues.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added i-g-t note and cc: stable] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... since finish_page_flip needs the vblank timestamp generated
in drm_handle_vblank. Somehow all the gmch platforms get it right,
but all the pch platform irq handlers get is wrong. Hooray for copy&
pasting!
Currently this gets papered over by a gross hack in finish_page_flip.
A second patch will remove that.
Note that without this, the new timestamp sanity checks in flip_test
occasionally get tripped up, hence the cc: stable tag.
Reviewed-by: mario.kleiner@tuebingen.mpg.de Tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: no loop over pipes in ivybridge_irq_handler(),
so make a similar change to that in ironlake_irq_handler()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I can't even find how I figured this might be needed anymore. But sure
enough, the value I'm reading back on platforms doesn't match what the
docs recommends.
It seemed to fix Chris' GT1 in limited testing as well.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: open-code _MASKED_BIT_{ENABLE,DISABLE}] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Note that gen3 is the only platform where we've got the bit
definitions right, hence the workaround of disabling sdvo hotplug
support on i945g/gm is not due to misdiagnosis of broken hotplug irq
handling ...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: add some blurb about sdvo hotplug fail on i945g/gm I've
wondered about while reviewing.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- Adjust context
- Handle all three cases in i915_driver_irq_postinstall() as there
are not separate functions for gen3 and gen4+
- Carry on using IS_SDVOB() in intel_sdvo_init()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On IVB and older, we basically have two registers: the control and the
data register. We write a few consecutitve times to the control
register, and we need these writes to arrive exactly in the specified
order.
Also, when we're changing the data register, we need to guarantee that
anything written to the control register already arrived (since
changing the control register can change where the data register
points to). Also, we need to make sure all the writes to the data
register happen exactly in the specified order, and we also *can't*
read the data register during this process, since reading and/or
writing it will change the place it points to.
So invoke the "better safe than sorry" rule and just be careful and
put barriers everywhere :)
On HSW we still have a control register that we write many times, but
we have many data registers.
Demanded-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- There are only two write_infoframe functions to be modified
- The other VIDEO_DIP_CTL writes are in entirely different functions] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... we will botch up the bit17 swizzling. Furthermore tiled pwrite is
a (now) unused slowpath, so no one really cares.
This fixes the last swizzling issues I have with i-g-t on my bit17
swizzling i915G. No regression, it's been broken since the dawn of
gem, but it's nice for regression tracking when really _all_ i-g-t
tests work.
Actually this is not true, Chris Wilson noticed while reviewing this
patch that the commit
During modeset we have to disable the pipe to reconfigure its timings
and maybe its size. Userspace may have queued up command buffers that
depend upon the pipe running in a certain configuration and so the
commands may become confused across the modeset. At the moment, we use a
less than satisfactory kick-scanline-waits should the GPU hang during
the modeset. It should be more reliable to wait for the pending
operations to complete first, even though we still have a window for
userspace to submit a broken command buffer during the modeset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have seen a number of "blt ring initialization failed" messages
where the ctl or start registers are not the correct value. Upon further
inspection, if the code just waited a little bit, it would read the
correct value. Adding the wait_for to these reads should eliminate the
issue.
Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently i915 driver checks [PCH_]LVDS register bits to decide
whether to set up the dual-link or the single-link mode. This relies
implicitly on that BIOS initializes the register properly at boot.
However, BIOS doesn't initialize it always. When the machine is
booted with the closed lid, BIOS skips the LVDS reg initialization.
This ends up in blank output on a machine with a dual-link LVDS when
you open the lid after the boot.
This patch adds a workaround for that problem by checking the initial
LVDS register value in VBT.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=37742 Tested-By: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Empirical evidence suggests that we need to: On at least one ivb
machine when running the hangman i-g-t test, the rings don't properly
initialize properly - the RING_START registers seems to be stuck at
all zeros.
Holding forcewake around this register init sequences makes chip reset
reliable again. Note that this is not the first such issue:
added delay loops to make RING_START and RING_CTL initialization
reliable on the blt ring at boot-up. So I guess it won't hurt if we do
this unconditionally for all force_wake needing gpus.
To avoid copy&pasting of the HAS_FORCE_WAKE check I've added a new
intel_info bit for that.
v2: Fixup missing commas in static struct and properly handling the
error case in init_ring_common, both noticed by Jani Nikula.
Reported-and-tested-by: Yang Guang <guang.a.yang@intel.com> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522 Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2:
- drop changes to Haswell device information
- NEEDS_FORCE_WAKE didn't refer to Valley View anyway] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[jcristau: further context adjustments for 3.4] Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Or at least plug another gapping hole. Apparrently hw desingers only
moved the bit field, but did not bother ot re-enumerate the planes
when adding support for a 3rd pipe.
Discovered by i-g-t/flip_test.
This may or may not fix the reference bugzilla, because that one
smells like we have still larger fish to fry.
v2: Fixup the impossible case to catch programming errors, noticed by
Chris Wilson.
References: https://bugs.freedesktop.org/show_bug.cgi?id=50069 Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Julien Cristau <jcristau@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm/i915: set phase sync pointer override enable before setting phase sync pointer
It turns out that this w/a isn't actually required on cpt/ppt and
positively harmful on ivb/ppt when using fdi B/C links - it results in
a black screen occasionally, with seemingfully everything working as
it should. The only failure indication I've found in the hw is that
eventually (but not right after the modeset completes) a pipe underrun
is signalled.
Big thanks to Arthur Runyan for all the ideas for registers to check
and changes to test, otherwise I couldn't ever have tracked this down!
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In gfs2_trans_add_bh(), gfs2 was testing if a there was a bd attached to the
buffer without having the gfs2_log_lock held. It was then assuming it would
stay attached for the rest of the function. However, without either the log
lock being held of the buffer locked, __gfs2_ail_flush() could detach bd at any
time. This patch moves the locking before the test. If there isn't a bd
already attached, gfs2 can safely allocate one and attach it before locking.
There is no way that the newly allocated bd could be on the ail list,
and thus no way for __gfs2_ail_flush() to detach it.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core hub thread (khubd) is designed with external USB hubs in
mind. It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.
The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits. When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event. If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.
This means that the hub code may lose port status changes because of
race conditions between clearing change bits. The user sees this as a
"dead port" that doesn't react to device connects.
The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.
We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's. Instead, stop the port polling timer, and
unconditionally restart it when the host resumes. If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.
This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit 0f2a79300a1471cf92ab43af165ea13555c8b0a5 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
The port reset code bails out early if the current connect status is
cleared (device disconnected). If we're issuing a hot reset, it may
also look at the link state before the reset is finished.
Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state. Therefore we can't trust it until the
reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.
The port state during reset is also unknown for USB 2.0 hubs. The hub
sends a reset signal by driving the bus into an SE0 state. This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.
Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.
Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant. When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.
This patch should be backported to all stable kernels.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects. To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.
The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes. We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect. However,
external USB 3.0 hubs don't need this code. They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set. Therefore it doesn't make sense to
put this code in the USB core.
This patch is part of a series to fix several reports of infinite loops
on device enumeration failure. This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller. The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.
When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host. The xHC then updates its internal
representation of the USB device to the 'Default' device state. If the
device was already in the Default state, the xHC will complete the
command with an error status.
If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.
For example, usb_reset_and_verify_device calls into hub_port_init in a
loop. Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers. Then the port will be disabled, but the udev will remain in
tact. usb_reset_and_verify_device will call into hub_port_init again.
On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command. This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail. The port will be disabled, and
the device won't be able to enumerate.
Fix this by ignoring the return value of the HCD reset_device callback.
USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset. In that case, the warm reset change bit
will be set, and the link state change bit may also be set. Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs. If these bits are not cleared, we may lose port change events
from the roothub.
Commit 2a44e499 ("drm/nouveau/disp: introduce proper init/fini, separate
from create/destroy") started to call display init routines on pre-nv50
hardware on module load. But LVDS init code sets driver state in a way
which prevents modesetting code from operating properly.
nv04_display_init calls nv04_dfp_restore, which sets encoder->last_dpms to
NV_DPMS_CLEARED.
nv04_lvds_dpms checks last_dpms mode (which is NV_DPMS_CLEARED) and wrongly
assumes it's a "powersaving mode", the new one (DRM_MODE_DPMS_OFF) is too,
so it skips calling some crucial lvds scripts.
Reported-by: Chris Paulson-Ellis <chris@edesix.com> Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5c8a86e10a7c164f44537fabdc169fd8b4e7a440 (usb: musb: drop unneeded
musb_debug trickery) erroneously removed '\n' from the driver's banner.
Concatenate all the banner substrings while adding it back...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we do have endpoints named like "ep-a" then bEndpointAddress is
counted internally by the gadget framework.
If we do have endpoints named like "ep-1" then bEndpointAddress is
assigned from the digit after "ep-".
If we do have both, then it is likely that after we used up the
"generic" endpoints we will use the digits and thus assign one
bEndpointAddress to multiple endpoints.
This theory can be proofed by using the completely enabled g_multi.
Without this patch, the mass storage won't enumerate and times out
because it shares endpoints with RNDIS.
This patch also adds fills up the endpoints list so we have in total
endpoints 1 to 15 in + out available while some of them are restricted
to certain types like BULK or ISO. Without this change the nokia gadget
won't load because the system does not provide enough (BULK) endpoints
but it did before ep-a - ep-f were removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: Tomasz Mloduchowski <q@qdot.me> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log