The open-coded mutex implementation for ARMv6+ cores suffers from a
severe lack of barriers, so in the uncontended case we don't actually
protect any accesses performed during the critical section.
Furthermore, the code is largely a duplication of the ARMv6+ atomic_dec
code but optimised to remove a branch instruction, as the mutex fastpath
was previously inlined. Now that this is executed out-of-line, we can
reuse the atomic access code for the locking (in fact, we use the xchg
code as this produces shorter critical sections).
This patch uses the generic xchg based implementation for mutexes on
ARMv6+, which introduces barriers to the lock/unlock operations and also
has the benefit of removing a fair amount of inline assembly code.
Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Pitre <nico@linaro.org> Reported-by: Shan Kang <kangshan0910@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't allocate enough data for this struct. As soon as we start
modifying event->event on the next lines, then we're going beyond the
end of the memory we allocated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Dave Airlie <airlied@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid constant wakeups caused by noisy irq lines when we don't even care
about the irq. This should be particularly useful for i945g/gm where the
hotplug has been disabled:
v2: While at it, remove the bogus hotplug_active read, and do not mask
hotplug_active[0] before checking whether the irq is needed, per discussion
with Daniel on IRC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442 Tested-by: Dominik Köppl <dominik@devwork.org> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.
So change it to make this number explicit.
This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.
For GPIOs of gpio-lpc32xx, gpio_direction_output() ignores the value argument
(initial value of output). This patch fixes this by setting the level
accordingly.
Signed-off-by: Roland Stigge <stigge@antcom.de> Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.
This patches fixed the issue by adding the gpio valid check.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Reviewed-by: Richard Zhao <richard.zhao@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mkl: backport to v3.5] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
kthread_worker provides minimalistic workqueue-like interface for
users which need a dedicated worker thread (e.g. for realtime
priority). It has basic queue, flush_work, flush_worker operations
which mostly match the workqueue counterparts; however, due to the way
flush_work() is implemented, it has a noticeable difference of not
allowing work items to be freed while being executed.
While the current users of kthread_worker are okay with the current
behavior, the restriction does impede some valid use cases. Also,
removing this difference isn't difficult and actually makes the code
easier to understand.
This patch reimplements flush_kthread_work() such that it uses a
flush_work item instead of queue/done sequence numbers.
if (destroy)
svc_shutdown_net(nfsd_serv, net);
svc_destroy(nfsd_server);
svc_shutdown_net(nfsd_serv, net) calls nfsd_last_thread(), which sets
nfsd_serv to NULL, causing a NULL dereference on the following line.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ACPI tables in the Macbook Air 5,1 define a single IOAPIC with id 2,
but the only remapping unit described in the DMAR table matches id 0.
Interrupt remapping fails as a result, and the kernel panics with the
message "timer doesn't work through Interrupt-remapped IO-APIC."
To fix this, check each IOAPIC for a corresponding IOMMU. If an IOMMU is
not found, do not allow IRQ remapping to be enabled.
v2: Move check to parse_ioapics_under_ir(), raise log level to KERN_ERR,
and add FW_BUG to the log message
v3: Skip check if IOMMU doesn't support interrupt remapping and remove
existing check that the IOMMU count equals the IOAPIC count
Newer firmware versions for the Pantech UML290 use a different
subclass ID. The Windows driver match on both IDs, so we do
that as well.
The ZTE (Vodafone) K5006-Z is a new device.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Dan Williams <dcbw@redhat.com> Cc: Thomas Schäfer <tschaefer@t-online.de>
[bmork: backported to 3.4: use driver whitelisting] Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 6 new devices and one modified device, based on
information from laptop vendor Windows drivers.
Sony provides a driver with two new devices using
a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The
Sony driver also adds a non-standard QMI/net
interface to the already supported 1199:9011
Gobi device. We do not know whether this is an
alternate interface number or an additional
interface which might be present, but that doesn't
really matter.
Lenovo provides a driver supporting 4 new devices:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with layout similar to MC7710
- MC7750 (114f:68a2) with layout similar to MC7710
- EM7700 (1199:901c) with layout similar to MC7710
Note regaring the three devices similar to MC7710:
The Windows drivers only support interface #8 on these
devices. The MC7710 can support QMI/net functions on
interface #19 and #20 as well, and this driver is
verified to work on interface #19 (a firmware bug is
suspected to prevent #20 from working).
We do not enable these additional interfaces until they
either show up in a Windows driver or are verified to
work in some other way. Therefore limiting the new
devices to interface #8 for now.
[bmork: backported to 3.4: use driver whitelisting] Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Oops affects 3.5 kernels and older, and is due to lookup_one_len()
calling down to the dentry revalidation code with a NULL pointer
to struct nameidata.
It is fixed upstream by commit 0b728e1911c (stop passing nameidata *
to ->d_revalidate())
The i2c-powermac driver now creates the i2c devices properly
from the device-tree, including workarounds for broken or
missing device-tree bits, so let's just use the normal probe
methods and get rid of the hand made device creation code.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Elimar Riesebieter <riesebie@lxtec.de> Cc: Michel Dänzer <michel@daenzer.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a number of workarounds for broken Apple device-trees
mostly around sound chips. It handles creating the missing audio codec
devices and works around various issues with missing addresses or
missing compatible properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Michel Dänzer <michel@daenzer.net> Cc: Elimar Riesebieter <riesebie@lxtec.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit 354ab8567ae3107a8cbe7228c3181990ba598aac titled
"Fix OMAP EHCI suspend/resume failure (i693)" is causing
the usb hub and device detection fails in beagle XM
causeing NFS not functional. This affects the core retention too.
The same commit logic needs to be revisted adhering to hwmod and
device tree framework.
for now, this commit id 354ab8567ae3107a8cbe7228c3181990ba598aac
titled "Fix OMAP EHCI suspend/resume failure (i693)" reverted.
This patch is validated on BeagleXM with NFS support over
usb ethernet and USB mass storage and other device detection.
pch_uart_interrupt() takes priv->port.lock which leads to two recursive
spinlock calls if low_latency==1 or CONFIG_PREEMPT_RT_FULL=y (one
otherwise):
pch_uart_interrupt
spin_lock_irqsave(priv->port.lock, flags)
case PCH_UART_IID_RDR_TO (data ready)
handle_rx_to
push_rx
tty_port_tty_get
spin_lock_irqsave(&port->lock, flags) <--- already hold this lock
...
tty_flip_buffer_push
...
flush_to_ldisc
spin_lock_irqsave(&tty->buf.lock)
spin_lock_irqsave(&tty->buf.lock)
disc->ops->receive_buf(tty, char_buf)
n_tty_receive_buf
tty->ops->flush_chars()
uart_flush_chars
uart_start
spin_lock_irqsave(&port->lock) <--- already hold this lock
Avoid this by using a dedicated lock to protect the eg20t_port structure
and IO access to its membase. This is more consistent with the 8250
driver. Ensure priv->lock is always take prior to priv->port.lock when
taken at the same time.
V2: Remove inadvertent whitespace change.
V3: Account for oops_in_progress for the private lock in
pch_console_write().
Note: Like the 8250 driver, if a printk is introduced anywhere inside
the pch_console_write() critical section, the kernel will hang
on a recursive spinlock on the private lock. The oops case is
handled by using a trylock in the oops_in_progress case.
Signed-off-by: Darren Hart <dvhart@linux.intel.com> CC: Tomoya MORINAGA <tomoya.rohm@gmail.com> CC: Feng Tang <feng.tang@intel.com> CC: Alexander Stein <alexander.stein@systec-electronic.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NAND flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NAND flash, need to be disabled.
This patch is similar to "powerpc/85xx: p1022ds: disable the NOR flash node
if video is enabled", except that it disables the NAND flash node instead.
This PIXIS node needs to remain enabled because it is used by platform code
to switch into indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rx Error interrupt(E.G. parity error) is not enabled.
So, when parity error occurs, error interrupt is not occurred.
As a result, the received data is not dropped.
This patch adds enable/disable rx error interrupt code.
For some reason, when the lirc daemon learns that a usb remote control
has been unplugged, it wants to read the sysfs attributes of the
disappearing device. This is useful for uncovering transient
inconsistencies, but less so for keeping the system running when such
inconsistencies exist.
Under some circumstances (like every time I unplug my dvb stick from
my laptop), lirc catches an rc_dev whose raw event handler has been
removed (presumably by ir_raw_event_unregister), and proceeds to
interrogate the raw protocols supported by the NULL pointer.
This patch avoids the NULL dereference, and ignores the issue of how
this state of affairs came about in the first place.
Version 2 incorporates changes recommended by Mauro Carvalho Chehab
(-ENODEV instead of -EINVAL, and a signed-off-by).
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If update_wall_time() is called and the current offset isn't large
enough to accumulate, avoid re-calling timekeeping_adjust which may
change the clock freq and can cause 1ns inconsistencies with
CLOCK_REALTIME_COARSE/CLOCK_MONOTONIC_COARSE.
Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1345595449-34965-5-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unexpected behavior could occur if the time is set to a value large
enough to overflow a 64bit ktime_t (which is something larger then the
year 2262).
Also unexpected behavior could occur if large negative offsets are
injected via adjtimex.
So this patch improves the sanity check timekeeping inputs by
improving the timespec_valid() check, and then makes better use of
timespec_valid() to make sure we don't set the time to an invalid
negative value or one that overflows ktime_t.
Note: This does not protect from setting the time close to overflowing
ktime_t and then letting natural accumulation cause the overflow.
Reported-by: CAI Qian <caiqian@redhat.com> Reported-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Link: http://lkml.kernel.org/r/1344454580-17031-1-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For one, the driver device pointer needs to be filled in, or the lirc core
will refuse to load the driver. And we really need to wire up all the
platform_device bits. This has been tested via the lirc sourceforge tree
and verified to work, been sitting there for months, finally getting
around to sending it. :\
Stefan reported a crash on a kernel before a3e5d1091c1 ("sched:
Don't call task_group() too many times in set_task_rq()"), he
found the reason to be that the multiple task_group()
invocations in set_task_rq() returned different values.
Looking at all that I found a lack of serialization and plain
wrong comments.
The below tries to fix it using an extra pointer which is
updated under the appropriate scheduler locks. Its not pretty,
but I can't really see another way given how all the cgroup
stuff works.
Reported-and-tested-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1340364965.18025.71.camel@twins Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.
Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.
Signed-off-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.
And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.
How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.
4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor
printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;
/*
* I add 16 to sizeof(fromAddr), ie 32,
* and pay attention to the definition of fromAddr,
* recvmsg() will overwrite sock_fd,
* since kernel will copy 32 bytes to userspace.
*
* If you just use sizeof(fromAddr), it works fine.
* */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}
close(sock_fd);
return 0;
}
Signed-off-by: Weiping Pan <wpan@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch tries to fix a dead loop in async_synchronize_full(), which
could be seen when preemption is disabled on a single cpu machine.
void async_synchronize_full(void)
{
do {
async_synchronize_cookie(next_cookie);
} while (!list_empty(&async_running) || !
list_empty(&async_pending));
}
async_synchronize_cookie() calls async_synchronize_cookie_domain() with
&async_running as the default domain to synchronize.
However, there might be some works in the async_pending list from other
domains. On a single cpu system, without preemption, there is no chance
for the other works to finish, so async_synchronize_full() enters a dead
loop.
It seems async_synchronize_full() wants to synchronize all entries in
all running lists(domains), so maybe we could just check the entry_count
to know whether all works are finished.
Currently, async_synchronize_cookie_domain() expects a non-NULL running
list ( if NULL, there would be NULL pointer dereference ), so maybe a
NULL pointer could be used as an indication for the functions to
synchronize all works in all domains.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dan Williams <dan.j.williams@gmail.com> Cc: Christian Kujau <lists@nerdbynature.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case that the link is already in the connected state and a
Pairing request arrives from the mgmt interface, hci_conn_security()
would be called but it was not considering LE links.
Reported-by: João Paulo Rechi Vita <jprvita@openbossa.org> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.
This also makes it clear that it is checking the security of the link.
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Tested-by: Shea Levy <shea@shealevy.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
so the other CPU may temporarily see worker->flags which doesn't have
either WORKER_UNBOUND or WORKER_REBIND set and perform local wakeup
prematurely.
Fix it by using single explicit assignment via ACCESS_ONCE().
Because idle workers have another WORKER_NOT_RUNNING flag, this bug
doesn't exist for them; however, update it to use the same pattern for
consistency.
tj: Applied the change to idle workers too and updated comments and
patch description a bit.
This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.
This fix is also needed in stable version 3.5.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iwl_dbgfs_fh_reg_read() can cause crashes and/or
BUG_ON in slub because the ifdefs are wrong, the
code in iwl_dump_fh() should use DEBUGFS, not
DEBUG to protect the buffer writing code.
Also, while at it, clean up the arguments to the
function, some code and make it generally safer.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is not started, we can't read its
SRAM and attempting to do so will cause issues.
Protect the debugfs read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver can't get the HW ready, we would release
the interrupt twice which made the kernel complain loudly.
Reported-by: Brian Cockrell <brian.cockrell@intel.com> Tested-by: Brian Cockrell <brian.cockrell@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.
In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.
intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:
[ 187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[ 187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0
so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.
This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:
Currently we've only frobbed this bit at irq_init time, but did
not restore it at resume time. Move it to the gen3 clock gating
function to fix this.
Notice while reading through code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only increase the higher 32bits if we really detect a wrap around.
v2: instead of increasing the higher 32bits just use the higher
32bits from the last emitted fence.
v3: also use last emitted fence value as upper limit.
The intention of this patch is to make fences as robust as
they where before introducing 64bit fences. This is
necessary because on older systems it looks like the fence
value gets corrupted on initialization.
Should also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=54129
https://bugs.freedesktop.org/show_bug.cgi?id=54662
https://bugzilla.redhat.com/show_bug.cgi?id=846505
https://bugzilla.redhat.com/show_bug.cgi?id=845639
3.5 needs a separate patch due to changes in the
fence code. Will send that out separately.
Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some new video switch keys that used by newer machines.
0xA0 - SDSP HDMI only
0xA1 - SDSP LCD + HDMI
0xA2 - SDSP CRT + HDMI
0xA3 - SDSP TV + HDMI
But in Linux, there is no suitable userspace application to handle this,
so, mapping them all to KEY_SWITCHVIDEOMODE.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Cc: <dri-devel@lists.freedesktop.org> Cc: Adam Jackson <ajax@redhat.com> Cc: Ian Pilcher <arequipeno@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley reported [1] a massive power regression, due to the
enabling of semaphores by default in 3.5. A workaround for him is to
again disable semaphores. And indeed, his system has a very hard time
to enter rc6 with semaphores enabled.
Ben Widawsky run around with a kill-a-watt a lot and noticed:
- There are indeed a few rare systems that seem to have a hard time
entering rc6 when desktop-idle.
- One machine, The Indestructible Toshiba regressed in this behaviour
between 3.5 and 3.6 in a merge commit! So rc6 behaviour with the
current setting seems to be highly timing dependent and not robust
at all.
- The behaviour James reported wrt semaphores seems to be a freak
timing thing that only happens on his specific machine, confirming
that enabling semaphores shouldn't reduce rc6 residency.
Now furthermore the Google ChromeOS guys reported [2] a while ago that
at least on some machines a simply a blinking cursor can keep the gpu
turbo at the highest frequency. This is because the current rps limits
used on snb/ivb are highly asymmetric.
On the theory that gpu turbo and rc6 tuning values are related, we've
tried whether the much saner looking (since much less asymmetric) rps
tuning values used for hsw would also help entering rc6 more robustly.
And it seems to mostly work, and we don't really have the resources to
through-roughly tune things in any better way: The values from the
ChromeOS ppl seem to fare a bit worse for James' machine, so I guess
we better stick with something vpg (the gpu hw/windows group)
provided, hoping that they've done their jobs.
Reference[1]: http://lists.freedesktop.org/archives/dri-devel/2012-July/025675.html
Reference[2]: http://lists.freedesktop.org/archives/intel-gfx/2012-July/018692.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53393 Tested-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset the lockup timeout on ring (re-)initialisation.
Otherwise we get error messages like this on gpu resets:
[ 1559.949177] radeon 0000:01:00.0: GPU lockup CP stall for more than 1482270msec
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a more recent APU stepping with a new PCI ID
shipping in the same board by Fujitsu which needs the
same quirk to correctly mark the back plane connectors.
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
If spread spectrum is enabled and in use for a given pll we
should not turn it off as it will lead to turning off display
for crtc that use the pll (this behavior was observed on chelsea
edp).
So we've had a fair few reports of fbcon handover breakage between
efi/vesafb and i915 surface recently, so I dedicated a couple of
days to finding the problem.
Essentially the last thing we saw was the conflicting framebuffer
message and that was all.
So after much tracing with direct netconsole writes (printks
under console_lock not so useful), I think I found the race.
Thread A (driver load) Thread B (timer thread)
unbind_con_driver -> |
bind_con_driver -> |
vc->vc_sw->con_deinit -> |
fbcon_deinit -> |
console_lock() |
| |
| fbcon_flashcursor timer fires
| console_lock() <- blocked for A
|
|
fbcon_del_cursor_timer ->
del_timer_sync
(BOOM)
Of course because all of this is under the console lock,
we never see anything, also since we also just unbound the active
console guess what we never see anything.
Hopefully this fixes the problem for anyone seeing vesafb->kms
driver handoff.
v1.1: add comment suggestion from Alan.
Signed-off-by: Dave Airlie <airlied@redhat.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Tested-by: Josh Boyer <jwboyer@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many of our larger systems, CPU 0 has had all of its IRQ resources
consumed before XPC loads. Worst cases on machines with multiple 10
GigE cards and multiple IB cards have depleted the entire first socket
of IRQs.
This patch makes selecting the node upon which IRQs are allocated (as
well as all the other GRU Message Queue structures) specifiable as a
module load param and has a default behavior of searching all nodes/cpus
for an available resources.
[akpm@linux-foundation.org: fix build: include cpu.h and module.h] Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If __dev_pm_qos_read_value(dev) returns a negative value,
rpm_suspend() should return -EPERM for dev even if its
power.no_callbacks flag is set. For this to happen, the device's
power.no_callbacks flag has to be checked after the PM QoS check,
so move the PM QoS check to rpm_check_suspend_allowed() (this will
make it cover idle notifications as well as runtime suspend too).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The power.deferred_resume can only be set if the runtime PM status
of device is RPM_SUSPENDING and it should be cleared after its
status has been changed, regardless of whether or not the runtime
suspend has been successful. However, it only is cleared on
suspend failure, while it may remain set on successful suspend and
is happily leaked to rpm_resume() executed in that case.
That shouldn't happen, so if power.deferred_resume is set in
rpm_suspend() after the status has been changed to RPM_SUSPENDED,
clear it before calling rpm_resume(). Then, it doesn't need to be
cleared before changing the status to RPM_SUSPENDING any more,
because it's always cleared after the status has been changed to
either RPM_SUSPENDED (on success) or RPM_ACTIVE (on failure).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devices whose power.no_callbacks flag is set, rpm_resume()
should return 1 if the device's parent is already active, so that
the callers of pm_runtime_get() don't think that they have to wait
for the device to resume (asynchronously) in that case (the core
won't queue up an asynchronous resume in that case, so there's
nothing to wait for anyway).
Modify the code accordingly (and make sure that an idle notification
will be queued up on success, even if 1 is to be returned).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct the offset by subtracting 20 from tm_hour before taking the
modulo 12.
[ "Why 20?" I hear you ask. Or at least I did.
Here's the reason why: RS5C348_BIT_PM is 32, and is - stupidly -
included in the RS5C348_HOURS_MASK define. So it's really subtracting
out that bit to get "hour+12". But then because it does things modulo
12, it needs to add the 12 in again afterwards anyway.
This code is confused. It would be much clearer if RS5C348_HOURS_MASK
just didn't include the RS5C348_BIT_PM bit at all, then it wouldn't
need to do the silly subtract either.
Whatever. It's all just math, the end result is the same. - Linus ]
Reported-by: James Nute <newten82@gmail.com> Tested-by: James Nute <newten82@gmail.com> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear AVX, AVX2 features along with clearing XSAVE feature bits,
as part of the parsing "noxsave" parameter.
Fixes the kernel boot panic with "noxsave" boot parameter.
We could have checked cpu_has_osxsave along with cpu_has_avx etc, but Peter
mentioned clearing the feature bits will be better for uses like
static_cpu_has() etc.
ARM recently moved to asm-generic/mutex-xchg.h for its mutex
implementation after the previous implementation was found to be missing
some crucial memory barriers. However, this has revealed some problems
running hackbench on SMP platforms due to the way in which the
MUTEX_SPIN_ON_OWNER code operates.
The symptoms are that a bunch of hackbench tasks are left waiting on an
unlocked mutex and therefore never get woken up to claim it. This boils
down to the following sequence of events:
At this point, the lock is unlocked, but Task B is in an uninterruptible
sleep with nobody to wake it up.
This patch fixes the problem by ensuring we put the lock into the
contended state if we fail to acquire it on the fastpath, ensuring that
any blocked waiters are woken up when the mutex is released.
Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Chris Mason <chris.mason@fusionio.com> Cc: Ingo Molnar <mingo@elte.hu> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/n/tip-6e9lrw2avczr0617fzl5vqb8@git.kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com> Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.
This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a661e1f383aecc86c6bbcf65afb15c892 "usb: host: xhci:
add platform driver support".
Signed-off-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.
The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.
There are two more registers that contains the information of the switchable
and non-switchable ports.
This patch adds the checking code for the two register so that only the
switchable ports are altered.
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log