Devesh Sharma [Mon, 22 May 2017 10:15:40 +0000 (03:15 -0700)]
RDMA/bnxt_re: Fix RQE posting logic
This patch adds code to ring RQ Doorbell aggressively
so that the adapter can DMA RQ buffers sooner, instead
of DMA all WQEs in the post_recv WR list together at the
end of the post_recv verb.
Also use spinlock to serialize RQ posting
Somnath Kotur [Mon, 22 May 2017 10:15:36 +0000 (03:15 -0700)]
RDMA/bnxt_re: Add HW workaround for avoiding stall for UD QPs
HW stalls out after 0x800000 WQEs are posted for UD QPs.
To workaround this problem, driver will send a modify_qp cmd
to the HW at around the halfway mark(0x400000) so that FW
can accordingly modify the QP context in the HW to prevent this
stall.
This workaround needs to be done for UD, QP1 and Raw Ethertype
packets. Added a counter to keep track of WQEs posted during post_send.
Selvin Xavier [Mon, 22 May 2017 10:15:34 +0000 (03:15 -0700)]
RDMA/bnxt_re: Dereg MR in FW before freeing the fast_reg_page_list
If the host buffers are freed before destroying MR in HW,
HW could try accessing these buffers. This could cause a host
crash. Fixing the code to avoid this condition.
Eddie Wai [Wed, 14 Jun 2017 10:26:23 +0000 (03:26 -0700)]
RDMA/bnxt_re: HW workarounds for handling specific conditions
This patch implements the following HW workarounds
1. The SQ depth needs to be augmented by 128 + 1 to avoid running
into an Out of order CQE issue
2. Workaround to handle the problem where the HW fast path engine continues
to access DMA memory in retranmission mode even after the WQE has
already been completed. If the HW reports this condition, driver detects
it and posts a Fence WQE. The driver stops reporting the completions
to stack until it receives completion for Fence WQE.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com> Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Mario Kleiner [Tue, 13 Jun 2017 05:17:11 +0000 (07:17 +0200)]
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
Commit e6b9a6c84b93
("drm/radeon: Make display watermark calculations more accurate")
made watermark calculations more accurate, but not for > 4k
resolutions on 32-Bit architectures, as it introduced an integer
overflow for those setups and resolutions.
Fix this by proper u64 casting and division.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: e6b9a6c84b93 ("drm/radeon: Make display watermark calculations more accurate") Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mario Kleiner [Tue, 13 Jun 2017 05:17:10 +0000 (07:17 +0200)]
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
Commit d63c277dc672e0
("drm/amdgpu: Make display watermark calculations more accurate")
made watermark calculations more accurate, but not for > 4k
resolutions on 32-Bit architectures, as it introduced an integer
overflow for those setups and resolutions.
Fix this by proper u64 casting and division.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: d63c277dc672 ("drm/amdgpu: Make display watermark calculations more accurate") Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 18 May 2017 08:31:01 +0000 (10:31 +0200)]
drm/radeon: fix "force the UVD DPB into VRAM as well"
The DPB must be in VRAM, but not in the first segment.
Signed-off-by: Christian König <christian.koenig@amd.com> Tested-by: Arthur Marsh <arthur.marsh@internode.on.net> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dan Carpenter [Wed, 14 Jun 2017 09:10:56 +0000 (12:10 +0300)]
Staging: rtl8723bs: fix an error code in isFileReadable()
The caller only cares about zero vs non-zero so this code actually works
fine but we should be returning a negative error code instead of a valid
pointer casted to int.
Mike Gerow [Wed, 14 Jun 2017 10:40:36 +0000 (12:40 +0200)]
video: fbdev: udlfb: drop log level for blanking
Drop log level for blanking from info to debug. Xorg likes to habitually
unblank when already unblanked and this can fill up logs over a long period
of time.
Signed-off-by: Mike Gerow <gerow@google.com> Cc: bernie@plugable.com Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Arnd Bergmann [Wed, 14 Jun 2017 10:40:36 +0000 (12:40 +0200)]
video: fbdev: avoid int-in-bool-context warning
gcc-7 suspects this code might be wrong because we use the
result of a multiplication as a bool:
drivers/video/fbdev/core/fbmon.c: In function 'fb_edid_add_monspecs':
drivers/video/fbdev/core/fbmon.c:1051:84: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
It's actually fine, so let's add a comparison to zero to make
that clear to the compiler too.
Merge tag 'iio-fixes-for-4.12b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.12 cycle.
* buffer-dma / buffer-dmaengine
- Fix missing include of buffer_impl.h after the split of buffer.h.
No driver in mainline is currently using these buffers so it wasn't
picked up by automated build tests.
* ad7152
- Fix a deadlock in ad7152_write_raw_samp_freq as the chip_state lock
was already held.
* inv_mpu6050
- Add low pass filter setting for chips newer than the MPU6500. None of
use previously picked up no the fact it was different on these newer
chips. It is separately set for the acceleration on these parts. There
is no normal reason to set it differently so the userspace interface
remains the same as for early parts.
* meson-saradc:
- Fix a potential crash by NULL pointer dereference in
meson_sar_adc_clear_fifo.
* mxs-lradc
- Fix a return value check where IS_ERR is used on a function that returns
NULL on error
Alistair Popple [Wed, 14 Jun 2017 04:47:50 +0000 (14:47 +1000)]
powerpc/npu-dma: Remove spurious WARN_ON when a PCI device has no of_node
Commit 4c3b89effc28 ("powerpc/powernv: Add sanity checks to
pnv_pci_get_{gpu|npu}_dev") introduced explicit warnings in
pnv_pci_get_npu_dev() when a PCIe device has no associated device-tree
node. However not all PCIe devices have an of_node and
pnv_pci_get_npu_dev() gets indirectly called at least once for every
PCIe device in the system. This results in spurious WARN_ON()'s so
remove it.
The same situation should not exist for pnv_pci_get_gpu_dev() as any
NPU based PCIe device requires a device-tree node.
Fixes: 4c3b89effc28 ("powerpc/powernv: Add sanity checks to pnv_pci_get_{gpu|npu}_dev") Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mateusz Jurczyk [Tue, 13 Jun 2017 18:06:12 +0000 (20:06 +0200)]
caif: Add sockaddr length check before accessing sa_family in connect handler
Verify that the caller-provided sockaddr structure is large enough to
contain the sa_family field, before accessing it in the connect()
handler of the AF_CAIF socket. Since the syscall doesn't enforce a minimum
size of the corresponding memory region, very short sockaddrs (zero or one
byte long) result in operating on uninitialized memory while referencing
sa_family.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Devesh Sharma [Mon, 22 May 2017 10:15:31 +0000 (03:15 -0700)]
RDMA/bnxt_re: Fixing the Control path command and response handling
Fixing a concurrency issue with creq handling. Each caller
was given a globally managed crsq element, which was
accessed outside a lock. This could result in corruption,
if lot of applications are simultaneously issuing Control Path
commands. Now, each caller will provide its own response buffer
and the responses will be copied under a lock.
Also, Fixing the queue full condition check for the CMDQ.
As a part of these changes, the control path code is refactored
to remove the code replication in the response status checking.
System cannot enter suspend mode because of heartbeat led trigger.
In autosleep_wq, try_to_suspend function will try to enter suspend
mode in specific period. it will get wakeup_count then call pm_notifier
chain callback function and freeze processes.
Heartbeat_pm_notifier is called and it call led_trigger_unregister to
change the trigger of led device to none. It will send uevent message
and the wakeup source count changed. As wakeup_count changed, suspend
will abort.
Fixes: 5ab92a7cb82c ("leds: handle suspend/resume in heartbeat trigger") Signed-off-by: Zhang Bo <bo.zhang@nxp.com> Acked-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
platform/x86: intel_telemetry_debugfs: fix oops when load/unload module
This fixes an oops found while testing load/unload of the
intel_telemetry_debugfs module. module_init uses register_pm_notifier
for PM callbacks, but unregister_pm_notifier was missing from
module_exit.
David S. Miller [Tue, 13 Jun 2017 17:34:13 +0000 (13:34 -0400)]
Merge tag 'mac80211-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Some fixes:
* Avi fixes some fallout from my mac80211 RX flags changes
* Emmanuel fixes an issue with adhering to the spec, and
an oversight in the SMPS management code
* Jason's patch makes mac80211 use constant-time memory
comparisons for message authentication, to avoid having
potentially observable timing differences
* my fix makes mac80211 set the basic rates bitmap before
the channel so the next update to the driver has more
consistent data - this required another rework patch to
remove some useless 5/10 MHz code that can never be hit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tayar, Tomer [Tue, 13 Jun 2017 09:15:59 +0000 (12:15 +0300)]
qed: fix dump of context data
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db444629 ("qed: Add support for debug data collection") Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Tue, 13 Jun 2017 17:10:18 +0000 (19:10 +0200)]
qmi_wwan: new Telewell and Sierra device IDs
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com> Reported-by: Teemu Likonen <tlikonen@iki.fi> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 13 Jun 2017 00:18:51 +0000 (17:18 -0700)]
net: phy: Fix MDIO_THUNDER dependencies
After commit 90eff9096c01 ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:
drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This happens because we don't hold pmc->lock in ip_mc_clear_src()
and a parallel mr_ifc_timer timer could jump in and access them.
The RCU lock is there but it is merely for pmc itself, this
spinlock could actually ensure we don't access them in parallel.
Thanks to Eric and Long for discussion on this bug.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Xin Long <lucien.xin@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ashwanth Goli [Tue, 13 Jun 2017 11:24:55 +0000 (16:54 +0530)]
net: rps: fix uninitialized symbol warning
This patch fixes uninitialized symbol warning that
got introduced by the following commit 773fc8f6e8d6 ("net: rps: send out pending IPI's on CPU hotplug")
Signed-off-by: Ashwanth Goli <ashwanth@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Kosina [Fri, 9 Jun 2017 11:15:37 +0000 (13:15 +0200)]
HID: let generic driver yield control iff specific driver has been enabled
There are many situations where generic HID driver provides some basic level
of support for certain device, but later this support (usually by implementing
vendor-specific extensions of HID protocol) is extended and the support moved
over to a separate (usually per-vendor) specific driver.
This might bring a rather unpleasant suprise for users, as all of a sudden
there is a new config option they have to enable in order to get any support
for their device whatsoever, although previous kernel versions provided basic
support through the generic driver. Which is rightfully seen as a regression.
Fix this by including the entry for a particular device in
hid_have_special_driver[] iff the specific config option has been specified,
and let generic driver handle the device otherwise.
Also make the behavior of hid_scan_report() (where the same decision is being
taken on a per-report level) consistent.
While at it, reshuffle the hid_have_special_driver[] a bit to restore the
alphabetical ordering (first order by config option, and within those
sections order by VID).
This is considered a short-term solution, before generic way of giving
precedence to special drivers and falling back to generic driver is
figured out.
While at it, fixup a missing entry for GFRM driver; thanks to Hans de Geode for
spotting this (and for discovering a few issues in the conversion).
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).
This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.
Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
sdata->smps_mode = SMPS_DYNAMIC
bss->req_smps = SMPS_OFF
That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.
Fix that by properly setting bss->req_smps in
ieee80211_start_ap.
Fixes: f69931748730 ("mac80211: set smps_mode according to ap params") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211/wpa: use constant time memory comparison for MACs
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sat, 10 Jun 2017 10:52:43 +0000 (13:52 +0300)]
mac80211: set bss_info data before configuring the channel
When mac80211 changes the channel, it also calls into the driver's
bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver
may, like iwlwifi does, access more data from bss_info in that case
and iwlwifi accesses the basic_rates bitmap, but if changing from a
band with more (basic) rates to one with fewer, an out-of-bounds
access of the rate array may result.
While we can't avoid having invalid data at some point in time, we
can avoid having it while we call the driver - so set up all the
data before configuring the channel, and then apply it afterwards.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sat, 10 Jun 2017 10:52:44 +0000 (13:52 +0300)]
mac80211: remove 5/10 MHz rate code from station MLME
There's no need for the station MLME code to handle bitrates for 5
or 10 MHz channels when it can't ever create such a configuration.
Remove the unnecessary code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avraham Stern [Mon, 12 Jun 2017 07:44:58 +0000 (10:44 +0300)]
mac80211: Fix incorrect condition when checking rx timestamp
If the driver reports the rx timestamp at PLCP start, mac80211 can
only handle legacy encoding, but the code checks that the encoding
is not legacy. Fix this.
Fixes: da6a4352e7c8 ("mac80211: separate encoding/bandwidth from flags") Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhenyu Wang [Fri, 9 Jun 2017 07:48:05 +0000 (15:48 +0800)]
drm/i915: Fix GVT-g PVINFO version compatibility check
Current it's strictly checked if PVINFO version matches 1.0
for GVT-g i915 guest which doesn't help for compatibility at
all and forces GVT-g host can't extend PVINFO easily with version
bump for real compatibility check.
This fixes that to check minimal required PVINFO version instead.
v2:
- drop unneeded version macro
- use only major version for sanity check
v3:
- fix up PVInfo value with kernel type
- one indent fix
Ville Syrjälä [Thu, 8 Jun 2017 14:40:02 +0000 (17:40 +0300)]
drm/i915: Fix SKL+ watermarks for 90/270 rotation
skl_check_plane_surface() already rotates the clipped plane source
coordinates to match the scanout direction because that's the way
the GTT mapping is set up. Thus we no longer need to rotate the
coordinates in the watermark code.
For cursors we use the non-clipped coordinates which are not rotated
appropriately, but that doesn't actually matter since cursors don't
even support 90/270 degree rotation.
Ville Syrjälä [Thu, 8 Jun 2017 14:40:01 +0000 (17:40 +0300)]
drm/i915: Fix scaling check for 90/270 degree plane rotation
Starting from commit b63a16f6cd89 ("drm/i915: Compute display surface
offset in the plane check hook for SKL+") we've already rotated the src
coordinates by 270 degrees by the time we check if a scaler is needed
or not, so we must not account for the rotation a second time.
Previously we did these steps in the opposite order and hence the
scaler check had to deal with rotation itself. The double rotation
handling causes us to enable a scaler pretty much every time 90/270
degree plane rotation is requested, leading to fuzzier fonts and whatnot.
v2: s/unsigned/unsigned int/ to appease checkpatch
v3: s/DRM_ROTATE_0/DRM_MODE_ROTATE_0/
The double free problem involves the mnt_opts field of the
security_mnt_opts struct, selinux_parse_opts_str() frees the memory
on error, but doesn't set the field to NULL so if the caller later
attempts to call security_free_mnt_opts() we trigger the problem.
In order to play it safe we change selinux_parse_opts_str() to call
security_free_mnt_opts() on error instead of free'ing the memory
directly. This should ensure that everything is handled correctly,
regardless of what the caller may do.
Fixes: e0007529893c1c06 ("LSM/SELinux: Interfaces to allow FS to control mount options") Cc: stable@vger.kernel.org Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Vlastimil Babka [Mon, 12 Jun 2017 07:21:30 +0000 (09:21 +0200)]
x86/mm: Disable 1GB direct mappings when disabling 2MB mappings
The kmemleak and debug_pagealloc features both disable using huge pages for
direct mappings so they can do cpa() on page level granularity in any context.
However they only do that for 2MB pages, which means 1GB pages can still be
used if the CPU supports it, unless disabled by a boot param, which is
non-obvious. Disable also 1GB pages when disabling 2MB pages.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vegard Nossum <vegardno@ifi.uio.no> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/2be70c78-6130-855d-3dfa-d87bd1dd4fda@suse.cz Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Tue, 13 Jun 2017 06:09:10 +0000 (15:09 +0900)]
Merge tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
- don't use linux IRQ #0 in legacy irq domains: fixes timer interrupt
assignment when it's hardware IRQ # is 0 and the kernel is built w/o
device tree support
- reduce reservation size for double exception vector literals from 48
to 20 bytes: fixes build on cores with small user exception vector
- cleanups: use kmalloc_array instead of kmalloc in simdisk_init and
seq_puts instead of seq_printf in c_show.
* tag 'xtensa-20170612' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: don't use linux IRQ #0
xtensa: reduce double exception literal reservation
xtensa: ISS: Use kmalloc_array() in simdisk_init()
xtensa: Use seq_puts() in c_show()
Linus Torvalds [Tue, 13 Jun 2017 06:07:11 +0000 (15:07 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- A fix for KVM to avoid kernel oopses in case of host protection
faults due to runtime instrumentation
- A fix for the AP bus to avoid dead devices after unbind / bind
- A fix for a compile warning merged from the vfio_ccw tree
- Updated default configurations
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfig
s390/zcrypt: Fix blocking queue device after unbind/bind.
s390/vfio_ccw: make some symbols static
s390/kvm: do not rely on the ILC on kvm host protection fauls
Jacob Keller [Mon, 12 Jun 2017 22:38:36 +0000 (15:38 -0700)]
i40e: fix handling of HW ATR eviction
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a36 ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Mon, 12 Jun 2017 20:43:03 +0000 (15:43 -0500)]
PCI: endpoint: Select CRC32 to fix test build error
The PCI endpoint test driver uses crc32_le() so it should select
CRC32. Fixes this build error (when CRC32=m):
drivers/built-in.o: In function `pci_epf_test_cmd_handler':
pci-epf-test.c:(.text+0x2d98d): undefined reference to `crc32_le'
Fixes: 349e7a85b25f ("PCI: endpoint: functions: Add an EP function to test PCI") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
When HSR interface is setup using ip link command, an annoying warning
appears with the trace as below:-
[ 203.019828] hsr_get_node: Non-HSR frame
[ 203.019833] Modules linked in:
[ 203.019848] CPU: 0 PID: 158 Comm: sd-resolve Tainted: G W 4.12.0-rc3-00052-g9fa6bf70 #2
[ 203.019853] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 203.019869] [<c0110280>] (unwind_backtrace) from [<c010c2f4>] (show_stack+0x10/0x14)
[ 203.019880] [<c010c2f4>] (show_stack) from [<c04b9f64>] (dump_stack+0xac/0xe0)
[ 203.019894] [<c04b9f64>] (dump_stack) from [<c01374e8>] (__warn+0xd8/0x104)
[ 203.019907] [<c01374e8>] (__warn) from [<c0137548>] (warn_slowpath_fmt+0x34/0x44)
root@am57xx-evm:~# [ 203.019921] [<c0137548>] (warn_slowpath_fmt) from [<c081126c>] (hsr_get_node+0x148/0x170)
[ 203.019932] [<c081126c>] (hsr_get_node) from [<c0814240>] (hsr_forward_skb+0x110/0x7c0)
[ 203.019942] [<c0814240>] (hsr_forward_skb) from [<c0811d64>] (hsr_dev_xmit+0x2c/0x34)
[ 203.019954] [<c0811d64>] (hsr_dev_xmit) from [<c06c0828>] (dev_hard_start_xmit+0xc4/0x3bc)
[ 203.019963] [<c06c0828>] (dev_hard_start_xmit) from [<c06c13d8>] (__dev_queue_xmit+0x7c4/0x98c)
[ 203.019974] [<c06c13d8>] (__dev_queue_xmit) from [<c0782f54>] (ip6_finish_output2+0x330/0xc1c)
[ 203.019983] [<c0782f54>] (ip6_finish_output2) from [<c0788f0c>] (ip6_output+0x58/0x454)
[ 203.019994] [<c0788f0c>] (ip6_output) from [<c07b16cc>] (mld_sendpack+0x420/0x744)
As this is an expected path to hsr_get_node() with frame coming from
the master interface, add a check to ensure packet is not from the
master port and then warn.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Zijlstra [Mon, 12 Jun 2017 11:52:46 +0000 (13:52 +0200)]
x86/debug: Handle early WARN_ONs proper
Hans managed to trigger a WARN very early in the boot which killed his
(Virtual) box.
The reason is that the recent rework of WARN() to use UD0 forgot to add the
fixup_bug() call to early_fixup_exception(). As a result the kernel does
not handle the WARN_ON injected UD0 exception and panics.
Add the missing fixup call, so early UD's injected by WARN() get handled.
Fixes: 9a93848fe787 ("x86/debug: Implement __WARN() using UD0") Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Frank Mehnert <frank.mehnert@oracle.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Michael Thayer <michael.thayer@oracle.com> Link: http://lkml.kernel.org/r/20170612180108.w4vgu2ckucmllf3a@hirez.programming.kicks-ass.net
Corentin Labbe [Fri, 9 Jun 2017 11:48:41 +0000 (14:48 +0300)]
usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
YD Tseng [Fri, 9 Jun 2017 11:48:40 +0000 (14:48 +0300)]
usb: xhci: Fix USB 3.1 supported protocol parsing
xHCI host controllers can have both USB 3.1 and 3.0 extended speed
protocol lists. If the USB3.1 speed is parsed first and 3.0 second then
the minor revision supported will be overwritten by the 3.0 speeds and
the USB3 roothub will only show support for USB 3.0 speeds.
This was the case with a xhci controller with the supported protocol
capability listed below.
In xhci-mem.c, the USB 3.1 speed is parsed first, the min_rev of usb3_rhub
is set as 0x10. And then USB 3.0 is parsed. However, the min_rev of
usb3_rhub will be changed to 0x00. If USB 3.1 device is connected behind
this host controller, the speed of USB 3.1 device just reports 5G speed
using lsusb.
Christian Perle [Mon, 12 Jun 2017 08:06:57 +0000 (10:06 +0200)]
proc: snmp6: Use correct type in memset
Reading /proc/net/snmp6 yields bogus values on 32 bit kernels.
Use "u64" instead of "unsigned long" in sizeof().
Fixes: 4a4857b1c81e ("proc: Reduce cache miss in snmp6_seq_show") Signed-off-by: Christian Perle <christian.perle@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mzx/devfreq
Pull devfreq fixes from MyungJoo Ham.
* 'for-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mzx/devfreq:
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
'of_node_put()' should be called on pointer returned by
'of_parse_phandle()' when done. In this function this is done in all path
except this 'continue', so add it.
Fixes: 97735da074fd (drivers: cpuidle: Add status property to ARM idle states) Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Commit 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency
decrease checking) removed the 10 point substraction when comparing the
load against down_threshold but did not remove the related limit for the
down_threshold value. As a result, down_threshold lower than 11 is not
allowed even though values from 1 to 10 do work correctly too. The
comment ("cannot be lower than 11 otherwise freq will not fall") also
does not apply after removing the substraction.
For this reason, allow down_threshold to take any value from 1 to 99
and fix the related comment.
Fixes: 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency decrease checking) Signed-off-by: Tomasz Wilczyński <twilczynski@naver.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 3.10+ <stable@vger.kernel.org> # 3.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 39b64aa1c007 (cpufreq: schedutil: Reduce frequencies
slower) that introduced unintentional changes in behavior leading
to adverse effects on some systems.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Wed, 7 Jun 2017 04:54:58 +0000 (12:54 +0800)]
ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
Considering this case:
1. A program opens a sysfs table file 65535 times, it can increase
validation_count and first increment cause the table to be mapped:
validation_count = 65535
2. AML execution causes "Load" to be executed on the same
table, this time it cannot increase validation_count, so
validation_count remains:
validation_count = 65535
3. The program closes sysfs table file 65535 times, it can decrease
validation_count and the last decrement cause the table to be
unmapped:
validation_count = 0
4. AML code still accessing the loaded table, kernel crash can be
observed.
To prevent that from happening, add a validation_count threashold.
When it is reached, the validation_count can no longer be
incremented/decremented to invalidate the table descriptor (means
preventing table unmappings)
Note that code added in acpi_tb_put_table() is actually a no-op but
changes the warning message into a "warn once" one. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog, comments ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
configfs: Fix race between create_link and configfs_rmdir
This patch closes a long standing race in configfs between
the creation of a new symlink in create_link(), while the
symlink target's config_item is being concurrently removed
via configfs_rmdir().
This can happen because the symlink target's reference
is obtained by config_item_get() in create_link() before
the CONFIGFS_USET_DROPPING bit set by configfs_detach_prep()
during configfs_rmdir() shutdown is actually checked..
This originally manifested itself on ppc64 on v4.8.y under
heavy load using ibmvscsi target ports with Novalink API:
To close this race, go ahead and obtain the symlink's target
config_item reference only after the existing CONFIGFS_USET_DROPPING
check succeeds.
This way, if configfs_rmdir() wins create_link() will return -ENONET,
and if create_link() wins configfs_rmdir() will return -EBUSY.
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org
Laurent Pinchart [Sat, 10 Jun 2017 08:59:43 +0000 (11:59 +0300)]
drm: dw-hdmi: Fix compilation breakage by selecting REGMAP_MMIO
The dw-hdmi driver switched to regmap-mmio, but lacks the dependency in
Kconfig. This can result in compilation breakages. Fix it by selecting
REGMAP_MMIO.
Linus Torvalds [Sun, 11 Jun 2017 23:17:29 +0000 (16:17 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull key subsystem fixes from James Morris:
"Here are a bunch of fixes for Linux keyrings, including:
- Fix up the refcount handling now that key structs use the
refcount_t type and the refcount_t ops don't allow a 0->1
transition.
- Fix a potential NULL deref after error in x509_cert_parse().
- Don't put data for the crypto algorithms to use on the stack.
- Fix the handling of a null payload being passed to add_key().
- Fix incorrect cleanup an uninitialised key_preparsed_payload in
key_update().
- Explicit sanitisation of potentially secure data before freeing.
- Fixes for the Diffie-Helman code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (23 commits)
KEYS: fix refcount_inc() on zero
KEYS: Convert KEYCTL_DH_COMPUTE to use the crypto KPP API
crypto : asymmetric_keys : verify_pefile:zero memory content before freeing
KEYS: DH: add __user annotations to keyctl_kdf_params
KEYS: DH: ensure the KDF counter is properly aligned
KEYS: DH: don't feed uninitialized "otherinfo" into KDF
KEYS: DH: forbid using digest_null as the KDF hash
KEYS: sanitize key structs before freeing
KEYS: trusted: sanitize all key material
KEYS: encrypted: sanitize all key material
KEYS: user_defined: sanitize key payloads
KEYS: sanitize add_key() and keyctl() key payloads
KEYS: fix freeing uninitialized memory in key_update()
KEYS: fix dereferencing NULL payload with nonzero length
KEYS: encrypted: use constant-time HMAC comparison
KEYS: encrypted: fix race causing incorrect HMAC calculations
KEYS: encrypted: fix buffer overread in valid_master_desc()
KEYS: encrypted: avoid encrypting/decrypting stack buffers
KEYS: put keyring if install_session_keyring_to_cred() fails
KEYS: Delete an error message for a failed memory allocation in get_derived_key()
...
Linus Torvalds [Sun, 11 Jun 2017 22:51:56 +0000 (15:51 -0700)]
compiler, clang: properly override 'inline' for clang
Commit abb2ea7dfd82 ("compiler, clang: suppress warning for unused
static inline functions") just caused more warnings due to re-defining
the 'inline' macro.
So undef it before re-defining it, and also add the 'notrace' attribute
like the gcc version that this is overriding does.
Donald Sharp [Sat, 10 Jun 2017 20:30:17 +0000 (16:30 -0400)]
net: ipmr: Fix some mroute forwarding issues in vrf's
This patch fixes two issues:
1) When forwarding on *,G mroutes that are in a vrf, the
kernel was dropping information about the actual incoming
interface when calling ip_mr_forward from ip_mr_input.
This caused ip_mr_forward to send the multicast packet
back out the incoming interface. Fix this by
modifying ip_mr_forward to be handed the correctly
resolved dev.
2) When a unresolved cache entry is created we store
the incoming skb on the unresolved cache entry and
upon mroute resolution from the user space daemon,
we attempt to forward the packet. Again we were
not resolving to the correct incoming device for
a vrf scenario, before calling ip_mr_forward.
Fix this by resolving to the correct interface
and calling ip_mr_forward with the result.
Fixes: e58e41596811 ("net: Enable support for VRF with ipv4 multicast") Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com> Acked-by: David Ahern <dsahern@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Added BW check for DIM decision mechanism") kernels >= 4.9
("net/mlx5e: Fix wrong indications in DIM due to counter wraparound") kernels >= 4.9
("net/mlx5: Remove several module events out of ethtool stats") kernels >= 4.10
("net/mlx5: Enable 4K UAR only when page size is bigger than 4K") kernels >= 4.11
*all patches apply with no issue on their -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:50 +0000 (15:42 +0300)]
net: ena: bug fix in lost tx packets detection mechanism
check_for_missing_tx_completions() is called from a timer
task and looking for lost tx packets.
The old implementation accumulate all the lost tx packets
and did not check if those packets were retrieved on a later stage.
This cause to a situation where the driver reset
the device for no reason.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:49 +0000 (15:42 +0300)]
net: ena: disable admin msix while working in polling mode
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:48 +0000 (15:42 +0300)]
net: ena: fix theoretical Rx hang on low memory systems
For the rare case where the device runs out of free rx buffer
descriptors (in case of pressure on kernel memory),
and the napi handler continuously fail to refill new Rx descriptors
until device rx queue totally runs out of all free rx buffers
to post incoming packet, leading to a deadlock:
* The device won't send interrupts since all the new
Rx packets will be dropped.
* The napi handler won't try to allocate new Rx descriptors
since allocation is part of NAPI that's not being invoked any more
The fix involves detecting this scenario and rescheduling NAPI
(to refill buffers) by the keepalive/watchdog task.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:47 +0000 (15:42 +0300)]
net: ena: add missing unmap bars on device removal
This patch also change the mapping functions to devm_ functions
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:46 +0000 (15:42 +0300)]
net: ena: fix race condition between submit and completion admin command
Bug:
"Completion context is occupied" error printout will be noticed in
dmesg.
This error will cause the admin command to fail, which will lead to
an ena_probe() failure or a watchdog reset (depends on which admin
command failed).
Root cause:
__ena_com_submit_admin_cmd() is the function that submits new entries to
the admin queue.
The function have a check that makes sure the queue is not full and the
function does not override any outstanding command.
It uses head and tail indexes for this check.
The head is increased by ena_com_handle_admin_completion() which runs
from interrupt context, and the tail index is increased by the submit
function (the function is running under ->q_lock, so there is no risk
of multithread increment).
Each command is associated with a completion context. This context
allocated before call to __ena_com_submit_admin_cmd() and freed by
ena_com_wait_and_process_admin_cq_interrupts(), right after the command
was completed.
This can lead to a state where the head was increased, the check passed,
but the completion context is still in use.
Solution:
Use the atomic variable ->outstanding_cmds instead of using the head and
the tail indexes.
This variable is safe for use since it is bumped in get_comp_ctx() in
__ena_com_submit_admin_cmd() and is freed by comp_ctxt_release()
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:45 +0000 (15:42 +0300)]
net: ena: add missing return when ena_com_get_io_handlers() fails
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:44 +0000 (15:42 +0300)]
net: ena: fix bug that might cause hang after consecutive open/close interface.
Fixing a bug that the driver does not unmask the IO interrupts
in ndo_open():
occasionally, the MSI-X interrupt (for one or more IO queues)
can be masked when ndo_close() was called.
If that is followed by ndo open(),
then the MSI-X will be still masked so no interrupt
will be received by the driver.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow to detect admin completion is:
while (command_not_completed) {
if (timeout)
error
check_for_completion()
sleep()
}
So in case the sleep took more than the timeout
(in case the thread/workqueue was not scheduled due to higher priority
task or prolonged VMexit), the driver can detect a stall even if
the completion is present.
The fix changes the order of this function to first check for
completion and only after that check if the timeout expired.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 11 Jun 2017 19:02:01 +0000 (12:02 -0700)]
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness fixes from Ted Ts'o:
"Improve performance by using a lockless update mechanism suggested by
Linus, and make sure we refresh per-CPU entropy returned get_random_*
as soon as the CRNG is initialized"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: invalidate batched entropy after crng init
random: use lockless method of accessing and updating f->reg_idx
Linus Torvalds [Sun, 11 Jun 2017 18:57:47 +0000 (11:57 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix various bug fixes in ext4 caused by races and memory allocation
failures"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix fdatasync(2) after extent manipulation operations
ext4: fix data corruption for mmap writes
ext4: fix data corruption with EXT4_GET_BLOCKS_ZERO
ext4: fix quota charging for shared xattr blocks
ext4: remove redundant check for encrypted file on dio write path
ext4: remove unused d_name argument from ext4_search_dir() et al.
ext4: fix off-by-one error when writing back pages before dio read
ext4: fix off-by-one on max nr_pages in ext4_find_unwritten_pgoff()
ext4: keep existing extra fields when inode expands
ext4: handle the rest of ext4_mb_load_buddy() ENOMEM errors
ext4: fix off-by-in in loop termination in ext4_find_unwritten_pgoff()
ext4: fix SEEK_HOLE
jbd2: preserve original nofs flag during journal restart
ext4: clear lockdep subtype for quota files on quota off
Linus Torvalds [Sun, 11 Jun 2017 18:34:27 +0000 (11:34 -0700)]
Merge tag 'gpio-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A few overdue GPIO patches for the v4.12 kernel.
- Fix debounce logic on the Aspeed platform.
- Fix the "virtual gpio" things on the Intel Crystal Cove.
- Fix the blink counter selection on the MVEBU platform"
* tag 'gpio-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: fix gpio bank registration when pwm is used
gpio: mvebu: fix blink counter register selection
MAINTAINERS: remove self from GPIO maintainers
gpio: crystalcove: Do not write regular gpio registers for virtual GPIOs
gpio: aspeed: Don't attempt to debounce if disabled
Linus Torvalds [Sun, 11 Jun 2017 18:29:15 +0000 (11:29 -0700)]
Merge tag 'char-misc-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 4.12-rc5. Nothing major here,
just some small bugfixes found by people testing, and a MAINTAINERS
file update for the genwqe driver.
All have been in linux-next with no reported issues"
[ The cxl driver fix came in through the powerpc tree earlier ]
* tag 'char-misc-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
cxl: Avoid double free_irq() for psl,slice interrupts
mei: make sysfs modalias format similar as uevent modalias
drivers: char: mem: Fix wraparound check to allow mappings up to the end
MAINTAINERS: Change maintainer of genwqe driver
goldfish_pipe: use GFP_ATOMIC under spin lock
firmware: vpd: do not leak kobjects
firmware: vpd: avoid potential use-after-free when destroying section
firmware: vpd: do not leave freed section attributes to the list
Linus Torvalds [Sun, 11 Jun 2017 18:25:51 +0000 (11:25 -0700)]
Merge tag 'staging-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"These are mostly all IIO driver fixes, resolving a number of tiny
issues. There's also a ccree and lustre fix in here as well, both fix
problems found in those codebases.
All have been in linux-next with no reported issues"
* tag 'staging-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ccree: fix buffer copy
staging/lustre/lov: remove set_fs() call from lov_getstripe()
staging: ccree: add CRYPTO dependency
iio: adc: sun4i-gpadc-iio: fix parent device being used in devm function
iio: light: ltr501 Fix interchanged als/ps register field
iio: adc: bcm_iproc_adc: swap primary and secondary isr handler's
iio: trigger: fix NULL pointer dereference in iio_trigger_write_current()
iio: adc: max9611: Fix attribute measure unit
iio: adc: ti_am335x_adc: allocating too much in probe
iio: adc: sun4i-gpadc-iio: Fix module autoload when OF devices are registered
iio: adc: sun4i-gpadc-iio: Fix module autoload when PLATFORM devices are registered
iio: proximity: as3935: fix iio_trigger_poll issue
iio: proximity: as3935: fix AS3935_INT mask
iio: adc: Max9611: checking for ERR_PTR instead of NULL in probe
iio: proximity: as3935: recalibrate RCO after resume
Linus Torvalds [Sun, 11 Jun 2017 18:21:08 +0000 (11:21 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of user visible fixes (excepting one format string
change).
Four of the qla2xxx fixes only affect the firmware dump path, but it's
still important to the enterprise. The rest are various NULL pointer
crash conditions or outright driver hangs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: libcxgbi: in error case RST tcp conn
scsi: scsi_debug: Avoid PI being disabled when TPGS is enabled
scsi: qla2xxx: Fix extraneous ref on sp's after adapter break
scsi: lpfc: prevent potential null pointer dereference
scsi: lpfc: Avoid NULL pointer dereference in lpfc_els_abort()
scsi: lpfc: nvmet_fc: fix format string
scsi: qla2xxx: Fix crash due to NULL pointer dereference of ctx
scsi: qla2xxx: Fix mailbox pointer error in fwdump capture
scsi: qla2xxx: Set bit 15 for DIAG_ECHO_TEST MBC
scsi: qla2xxx: Modify T262 FW dump template to specify same start/end to debug customer issues
scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue
scsi: qla2xxx: Fix NULL pointer access due to redundant fc_host_port_name call
scsi: qla2xxx: Fix recursive loop during target mode configuration for ISP25XX leaving system unresponsive
scsi: bnx2fc: fix race condition in bnx2fc_get_host_stats()
scsi: qla2xxx: don't disable a not previously enabled PCI device
Linus Torvalds [Sun, 11 Jun 2017 18:15:09 +0000 (11:15 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"We expanded the device-dax fs type in 4.12 to be a generic provider of
a struct dax_device with an embedded inode. However, Sasha found some
basic negative testing was not run to verify that this fs cleanly
handles being mounted directly.
Note that the fresh rebase was done to remove an unnecessary Cc:
<stable> tag, but this commit otherwise had a build success
notification from the 0day robot."
iio: adc: meson-saradc: fix potential crash in meson_sar_adc_clear_fifo
meson_sar_adc_clear_fifo passes a 0 as value-pointer to regmap_read().
In case of the meson-saradc driver this ends up in regmap_mmio_read(),
where the value-pointer is de-referenced unconditionally to assign the
value which was read.
Fix this by passing an actual pointer, even though all we want to do is
to discard the value.
As a side-effect this fixes a sparse warning ("Using plain integer as
NULL pointer") as reported by Paolo Cretaro.
Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs") Reported-by: Paolo Cretaro <paolocretaro@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Tal Gilboa [Mon, 29 May 2017 14:02:55 +0000 (17:02 +0300)]
net/mlx5e: Fix wrong indications in DIM due to counter wraparound
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing") Signed-off-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tal Gilboa [Mon, 15 May 2017 11:13:16 +0000 (14:13 +0300)]
net/mlx5e: Added BW check for DIM decision mechanism
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Until now only interrupt and packet rate were sampled.
We found a scenario on which we get a false indication since a change in
DIM caused more aggregation and reduced packet rate while increasing BW.
We now regard a change as succesfull iff:
current_BW > (prev_BW + threshold) or
current_BW ~= prev_BW and current_PR > (prev_PR + threshold) or
current_BW ~= prev_BW and current_PR ~= prev_PR and
current_IR < (prev_IR - threshold)
Where BW = Bandwidth, PR = Packet rate and IR = Interrupt rate
Huy Nguyen [Mon, 8 May 2017 16:46:50 +0000 (11:46 -0500)]
net/mlx5: Remove several module events out of ethtool stats
Remove the following module event counters out of ethtool stats. The
reason for removing these event counters is that these events do not
occur without techinician's intervention.
module_pwr_budget_exd
module_long_range
module_no_eeprom
module_enforce_part
module_unknown_id
module_unknown_status
module_plug
Fixes: bedb7c909c19 ("net/mlx5e: Add port module event counters to ethtool stats") Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed by: Gal Pressman <galp@mellanox.com>
Andy Lutomirski [Fri, 9 Jun 2017 18:49:15 +0000 (11:49 -0700)]
sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()
idle_task_exit() can be called with IRQs on x86 on and therefore
should use switch_mm(), not switch_mm_irqs_off().
This doesn't seem to cause any problems right now, but it will
confuse my upcoming TLB flush changes. Nonetheless, I think it
should be backported because it's trivial. There won't be any
meaningful performance impact because idle_task_exit() is only
used when offlining a CPU.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: f98db6013c55 ("sched/core: Add switch_mm_irqs_off() and use it in the scheduler") Link: http://lkml.kernel.org/r/ca3d1a9fa93a0b49f5a8ff729eda3640fb6abdf9.1497034141.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
projects / karo-tx-linux.git / log