+++ /dev/null
-<!-- Copyright (C) 2003 Red Hat, Inc. -->
-<!-- This material may be distributed only subject to the terms -->
-<!-- and conditions set forth in the Open Publication License, v1.0 -->
-<!-- or later (the latest version is presently available at -->
-<!-- http://www.opencontent.org/openpub/). -->
-<!-- Distribution of the work or derivative of the work in any -->
-<!-- standard (paper) book form is prohibited unless prior -->
-<!-- permission is obtained from the copyright holder. -->
-<HTML
-><HEAD
-><TITLE
->Cirrus Logic ARM EP7212 Development Board
-Hardware Setup</TITLE
-><meta name="MSSmartTagsPreventParsing" content="TRUE">
-<META
-NAME="GENERATOR"
-CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
-"><LINK
-REL="HOME"
-TITLE="eCos User Guide"
-HREF="ecos-user-guide.html"><LINK
-REL="UP"
-TITLE="Target Setup"
-HREF="appendix-target-setup.html"><LINK
-REL="PREVIOUS"
-TITLE="Cirrus Logic ARM EP7211 Development
-Board Hardware Setup"
-HREF="setup-arm-ep7211.html"><LINK
-REL="NEXT"
-TITLE="Cirrus Logic ARM EP7312 Development Board
-Hardware Setup"
-HREF="setup-arm-ep7312.html"></HEAD
-><BODY
-CLASS="SECT1"
-BGCOLOR="#FFFFFF"
-TEXT="#000000"
-LINK="#0000FF"
-VLINK="#840084"
-ALINK="#0000FF"
-><DIV
-CLASS="NAVHEADER"
-><TABLE
-SUMMARY="Header navigation table"
-WIDTH="100%"
-BORDER="0"
-CELLPADDING="0"
-CELLSPACING="0"
-><TR
-><TH
-COLSPAN="3"
-ALIGN="center"
->eCos User Guide</TH
-></TR
-><TR
-><TD
-WIDTH="10%"
-ALIGN="left"
-VALIGN="bottom"
-><A
-HREF="setup-arm-ep7211.html"
-ACCESSKEY="P"
->Prev</A
-></TD
-><TD
-WIDTH="80%"
-ALIGN="center"
-VALIGN="bottom"
->Appendix A. Target Setup</TD
-><TD
-WIDTH="10%"
-ALIGN="right"
-VALIGN="bottom"
-><A
-HREF="setup-arm-ep7312.html"
-ACCESSKEY="N"
->Next</A
-></TD
-></TR
-></TABLE
-><HR
-ALIGN="LEFT"
-WIDTH="100%"></DIV
-><DIV
-CLASS="SECT1"
-><H1
-CLASS="SECT1"
-><A
-NAME="SETUP-ARM-EP7212">Cirrus Logic ARM EP7212 Development Board
-Hardware Setup</H1
-><P
->The Cirrus Logic EP7212 Development Board is almost identical
-to the EP7211 Development Board from a hardware setup viewpoint,
-and is based on the same port of eCos. Therefore the earlier documentation
-for the EP7211 Development Board can be considered equivalent, but
-with the following changes:</P
-><P
-></P
-><UL
-><LI
-><P
->The first serial port is silk screened as "UART 1" on
-the EP7211 Development Board, but is silk screened as "Serial Port
-0" on the EP7212 Development Board. Similarly "UART 2" is silk screened
-as "Serial Port 1" on the EP7212 Development Board.</P
-></LI
-><LI
-><P
->JP2 (used to control reprogramming of the FLASH) is not
-silkscreened with "Boot Enable".</P
-></LI
-><LI
-><P
->To setup the EP7212 Development Board for use with the
-ARM Multi-ICE JTAG debugging interface unit, it is necessary to
-connect TEST0 and TEST1 of the EP7212 to ground. On the Development
-Board, this is accomplished by placing shorting blocks on JP47 and
-JP48. When the shorting blocks are fitted, the board can only be
-operated through the Multi-ICE - debugging over a serial line is
-not possible.</P
-></LI
-><LI
-><P
->Pre-built GDB stubs are
- provided in the directory
- <TT
-CLASS="FILENAME"
->loaders/arm-edb7212</TT
-> relative to the
- root of your eCos installation</P
-></LI
-><LI
-><P
->When rebuilding the GDB stub ROM image, change the "Cirrus
-Logic processor variant" option (CYGHWR_HAL_ARM_EDB7XXX_VARIANT)
-from the EP7211 to the EP7212. This can be selected in the
-<SPAN
-CLASS="emphasis"
-><I
-CLASS="EMPHASIS"
->eCos Configuration Tool</I
-></SPAN
->
-, or if using ecosconfig, can be set by uncommenting the user_value
-property of this option in ecos.ecc and setting it to "EP7212".</P
-></LI
-></UL
-></DIV
-><DIV
-CLASS="NAVFOOTER"
-><HR
-ALIGN="LEFT"
-WIDTH="100%"><TABLE
-SUMMARY="Footer navigation table"
-WIDTH="100%"
-BORDER="0"
-CELLPADDING="0"
-CELLSPACING="0"
-><TR
-><TD
-WIDTH="33%"
-ALIGN="left"
-VALIGN="top"
-><A
-HREF="setup-arm-ep7211.html"
-ACCESSKEY="P"
->Prev</A
-></TD
-><TD
-WIDTH="34%"
-ALIGN="center"
-VALIGN="top"
-><A
-HREF="ecos-user-guide.html"
-ACCESSKEY="H"
->Home</A
-></TD
-><TD
-WIDTH="33%"
-ALIGN="right"
-VALIGN="top"
-><A
-HREF="setup-arm-ep7312.html"
-ACCESSKEY="N"
->Next</A
-></TD
-></TR
-><TR
-><TD
-WIDTH="33%"
-ALIGN="left"
-VALIGN="top"
->Cirrus Logic ARM EP7211 Development
-Board Hardware Setup</TD
-><TD
-WIDTH="34%"
-ALIGN="center"
-VALIGN="top"
-><A
-HREF="appendix-target-setup.html"
-ACCESSKEY="U"
->Up</A
-></TD
-><TD
-WIDTH="33%"
-ALIGN="right"
-VALIGN="top"
->Cirrus Logic ARM EP7312 Development Board
-Hardware Setup</TD
-></TR
-></TABLE
-></DIV
-></BODY
-></HTML
->
\ No newline at end of file
projects / karo-tx-redboot.git / blobdiff