include/configs/aristainetos.h

   1 /*
   2  * (C) Copyright 2015
   3  * (C) Copyright 2014
   4  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   8  *
   9  * Configuration settings for the Freescale i.MX6Q SabreSD board.
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13 #ifndef __ARISTAINETOS_CONFIG_H
  14 #define __ARISTAINETOS_CONFIG_H
  15
  16
  17 #include "mx6_common.h"
  18 #include <linux/sizes.h>
  19
  20 #define CONFIG_DISPLAY_CPUINFO
  21 #define CONFIG_DISPLAY_BOARDINFO
  22
  23 #include <asm/arch/imx-regs.h>
  24 #include <asm/imx-common/gpio.h>
  25
  26 #define CONFIG_MACH_TYPE        4501
  27 #define CONFIG_MMCROOT          "/dev/mmcblk0p1"
  28 #define CONFIG_HOSTNAME         aristainetos
  29 #define PHYS_SDRAM_SIZE         (1u * 1024 * 1024 * 1024)
  30
  31 #define CONFIG_SYS_GENERIC_BOARD
  32
  33 /* Size of malloc() pool */
  34 #define CONFIG_SYS_MALLOC_LEN           (64 * SZ_1M)
  35
  36 #define CONFIG_BOARD_EARLY_INIT_F
  37 #define CONFIG_MXC_GPIO
  38
  39 #define CONFIG_MXC_UART
  40 #define CONFIG_MXC_UART_BASE    UART5_BASE
  41 #define CONFIG_CONSOLE_DEV      "ttymxc4"
  42
  43 #define CONFIG_CMD_FUSE
  44 #define CONFIG_MXC_OCOTP
  45
  46 /* MMC Configs */
  47 #define CONFIG_FSL_ESDHC
  48 #define CONFIG_FSL_USDHC
  49 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  50
  51 #define CONFIG_MMC
  52 #define CONFIG_CMD_MMC
  53 #define CONFIG_GENERIC_MMC
  54 #define CONFIG_BOUNCE_BUFFER
  55 #define CONFIG_CMD_EXT2
  56 #define CONFIG_CMD_FAT
  57 #define CONFIG_DOS_PARTITION
  58
  59 #define CONFIG_CMD_PING
  60 #define CONFIG_CMD_DHCP
  61 #define CONFIG_CMD_MII
  62 #define CONFIG_CMD_NET
  63 #define CONFIG_FEC_MXC
  64 #define CONFIG_MII
  65 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  66 #define CONFIG_FEC_XCV_TYPE             RMII
  67 #define CONFIG_ETHPRIME                 "FEC"
  68 #define CONFIG_FEC_MXC_PHYADDR          0
  69
  70 #define CONFIG_PHYLIB
  71 #define CONFIG_PHY_MICREL
  72
  73 #define CONFIG_CMD_SF
  74 #define CONFIG_SPI_FLASH
  75 #define CONFIG_SPI_FLASH_MTD
  76 #define CONFIG_SPI_FLASH_STMICRO
  77 #define CONFIG_MXC_SPI
  78 #define CONFIG_SF_DEFAULT_BUS           3
  79 #define CONFIG_SF_DEFAULT_CS            0
  80 #define CONFIG_SF_DEFAULT_SPEED         20000000
  81 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  82 #define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
  83 /* allow to overwrite serial and ethaddr */
  84 #define CONFIG_ENV_OVERWRITE
  85 #define CONFIG_CONS_INDEX               1
  86 #define CONFIG_BAUDRATE                 115200
  87
  88 /* Command definition */
  89 #include <config_cmd_default.h>
  90
  91 #define CONFIG_CMD_BMODE
  92 #define CONFIG_CMD_BOOTZ
  93 #define CONFIG_CMD_SETEXPR
  94 #undef CONFIG_CMD_IMLS
  95
  96 #define CONFIG_BOOTDELAY                3
  97
  98 #define CONFIG_LOADADDR                 0x12000000
  99 #define CONFIG_SYS_TEXT_BASE            0x17800000
 100
 101 #define CONFIG_EXTRA_ENV_SETTINGS \
 102         "script=u-boot.scr\0" \
 103         "fit_file=/boot/system.itb\0" \
 104         "loadaddr=0x12000000\0" \
 105         "fit_addr_r=0x14000000\0" \
 106         "uboot=/boot/u-boot.imx\0" \
 107         "uboot_sz=d0000\0" \
 108         "rescue_sys_addr=f0000\0" \
 109         "rescue_sys_length=f10000\0" \
 110         "board_type=aristainetos7@1\0" \
 111         "panel=lb07wv8\0" \
 112         "splashpos=m,m\0" \
 113         "console=" CONFIG_CONSOLE_DEV "\0" \
 114         "fdt_high=0xffffffff\0"   \
 115         "initrd_high=0xffffffff\0" \
 116         "mtdids=nand0=gpmi-nand,nor0=spi3.0\0" \
 117         "mtdparts=mtdparts=spi3.0:832k(u-boot),64k(env),64k(env-red)," \
 118                 "-(rescue-system);gpmi-nand:-(ubi)\0" \
 119         "addmisc=setenv bootargs ${bootargs} consoleblank=0\0" \
 120         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
 121         "set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
 122                 "default ${board_type}\0" \
 123         "get_env=mw ${loadaddr} 0 0x20000;" \
 124                 "mmc rescan;" \
 125                 "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
 126                 "env import -t ${loadaddr}\0" \
 127         "default_env=mw ${loadaddr} 0 0x20000;" \
 128                 "env export -t ${loadaddr} serial# ethaddr eth1addr " \
 129                 "board_type panel;" \
 130                 "env default -a;" \
 131                 "env import -t ${loadaddr}\0" \
 132         "loadbootscript=" \
 133                 "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 134         "bootscript=echo Running bootscript from mmc ...; " \
 135                 "source\0" \
 136         "mmcpart=1\0" \
 137         "mmcdev=0\0" \
 138         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 139         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 140                 "root=${mmcroot}\0" \
 141         "mmcboot=echo Booting from mmc ...; " \
 142                 "run mmcargs addmtd addmisc set_fit_default;" \
 143                 "bootm ${fit_addr_r}\0" \
 144         "mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
 145                 "${fit_file}\0" \
 146         "mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
 147                 "${uboot}\0" \
 148         "mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
 149                 "setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
 150                 "setexpr uboot_maxsize ${uboot_sz} - 400;" \
 151                 "mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
 152                 "run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
 153                 "sf write ${loadaddr} 400 ${filesize};" \
 154                 "sf read ${cmp_buf} 400 ${uboot_sz};" \
 155                 "cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
 156         "ubiargs=setenv bootargs console=${console},${baudrate} " \
 157                 "ubi.mtd=0,2048 root=ubi0:rootfs rootfstype=ubifs\0 " \
 158         "ubiboot=echo Booting from ubi ...; " \
 159                 "run ubiargs addmtd addmisc set_fit_default;" \
 160                 "bootm ${fit_addr_r}\0" \
 161         "ubifs_load_fit=sf probe;ubi part ubi 2048;ubifsmount ubi:rootfs;" \
 162                 "ubifsload ${fit_addr_r} /boot/system.itb; " \
 163                 "imi ${fit_addr_r}\0 " \
 164         "rescueargs=setenv bootargs console=${console},${baudrate} " \
 165                 "root=/dev/ram rw\0 " \
 166         "rescueboot=echo Booting rescue system from NOR ...; " \
 167                 "run rescueargs addmtd addmisc set_fit_default;" \
 168                 "bootm ${fit_addr_r}\0" \
 169         "rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
 170                 "${rescue_sys_length}; imi ${fit_addr_r}\0 "
 171
 172 #define CONFIG_BOOTCOMMAND \
 173         "mmc dev ${mmcdev};" \
 174         "if mmc rescan; then " \
 175                 "if run loadbootscript; then " \
 176                         "run bootscript; " \
 177                 "else " \
 178                         "if run mmc_load_fit; then " \
 179                                 "run mmcboot; " \
 180                         "else " \
 181                                 "if run ubifs_load_fit; then " \
 182                                         "run ubiboot; " \
 183                                 "else " \
 184                                         "if run rescue_load_fit; then " \
 185                                                 "run rescueboot; " \
 186                                         "else " \
 187                                                 "echo RESCUE SYSTEM BOOT " \
 188                                                         "FAILURE;" \
 189                                         "fi; " \
 190                                 "fi; " \
 191                         "fi; " \
 192                 "fi; " \
 193         "else " \
 194                 "if run ubifs_load_fit; then " \
 195                         "run ubiboot; " \
 196                 "else " \
 197                         "if run rescue_load_fit; then " \
 198                                 "run rescueboot; " \
 199                         "else " \
 200                                 "echo RESCUE SYSTEM BOOT FAILURE;" \
 201                         "fi; " \
 202                 "fi; " \
 203         "fi"
 204
 205 #define CONFIG_ARP_TIMEOUT              200UL
 206
 207 /* Miscellaneous configurable options */
 208 #define CONFIG_SYS_LONGHELP
 209 #define CONFIG_SYS_HUSH_PARSER
 210 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 211 #define CONFIG_AUTO_COMPLETE
 212 #define CONFIG_SYS_CBSIZE               256
 213
 214 /* Print Buffer Size */
 215 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 216 #define CONFIG_SYS_MAXARGS             16
 217 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 218
 219 #define CONFIG_SYS_MEMTEST_START        PHYS_SDRAM
 220 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 0x100000)
 221 #define CONFIG_SYS_MEMTEST_SCRATCH      0x10800000
 222
 223 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 224
 225 #define CONFIG_CMDLINE_EDITING
 226 #define CONFIG_STACKSIZE                (128 * 1024)
 227
 228 /* Physical Memory Map */
 229 #define CONFIG_NR_DRAM_BANKS            1
 230 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 231
 232 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 233 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 234 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 235
 236 #define CONFIG_SYS_INIT_SP_OFFSET \
 237         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 238 #define CONFIG_SYS_INIT_SP_ADDR \
 239         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 240
 241 /* FLASH and environment organization */
 242 #define CONFIG_SYS_NO_FLASH
 243
 244 #define CONFIG_ENV_SIZE                 (12 * 1024)
 245 #define CONFIG_ENV_IS_IN_SPI_FLASH
 246 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 247 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 248 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 249 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 250 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 251 #define CONFIG_ENV_SECT_SIZE            (0x010000)
 252 #define CONFIG_ENV_OFFSET               (0x0d0000)
 253 #define CONFIG_ENV_OFFSET_REDUND        (0x0e0000)
 254
 255 #define CONFIG_OF_LIBFDT
 256
 257 #define CONFIG_CMD_CACHE
 258
 259 #define CONFIG_SYS_FSL_USDHC_NUM        2
 260
 261 #define CONFIG_CMD_I2C
 262 #define CONFIG_SYS_I2C
 263 #define CONFIG_SYS_I2C_MXC
 264 #define CONFIG_SYS_I2C_SPEED            100000
 265 #define CONFIG_SYS_I2C_SLAVE            0x7f
 266 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x00} }
 267
 268 #define CONFIG_CMD_GPIO
 269 #define CONFIG_GPIO_ENABLE_SPI_FLASH    IMX_GPIO_NR(2, 15)
 270
 271 /* NAND stuff */
 272 #define CONFIG_CMD_NAND
 273 #define CONFIG_CMD_NAND_TRIMFFS
 274 #define CONFIG_NAND_MXS
 275 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 276 #define CONFIG_SYS_NAND_BASE            0x40000000
 277 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 278 #define CONFIG_SYS_NAND_ONFI_DETECTION
 279
 280 /* DMA stuff, needed for GPMI/MXS NAND support */
 281 #define CONFIG_APBH_DMA
 282 #define CONFIG_APBH_DMA_BURST
 283 #define CONFIG_APBH_DMA_BURST8
 284
 285 /* RTC */
 286 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
 287 #define CONFIG_SYS_RTC_BUS_NUM  2
 288 #define CONFIG_RTC_M41T11
 289 #define CONFIG_CMD_DATE
 290
 291 /* USB Configs */
 292 #define CONFIG_CMD_USB
 293 #define CONFIG_CMD_FAT
 294 #define CONFIG_USB_EHCI
 295 #define CONFIG_USB_EHCI_MX6
 296 #define CONFIG_USB_STORAGE
 297 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 298 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 299 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 300 #define CONFIG_MXC_USB_FLAGS    0
 301
 302 #define ARISTAINETOS_USB_OTG_PWR        IMX_GPIO_NR(4, 15)
 303 #define ARISTAINETOS_USB_H1_PWR         IMX_GPIO_NR(3, 31)
 304
 305 /* UBI support */
 306 #define CONFIG_CMD_MTDPARTS
 307 #define CONFIG_MTD_PARTITIONS
 308 #define CONFIG_MTD_DEVICE
 309 #define CONFIG_RBTREE
 310 #define CONFIG_LZO
 311 #define CONFIG_CMD_UBI
 312 #define CONFIG_CMD_UBIFS
 313
 314 #define CONFIG_MTD_UBI_FASTMAP
 315 #define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT      1
 316
 317 #define CONFIG_HW_WATCHDOG
 318 #define CONFIG_IMX_WATCHDOG
 319
 320 #define CONFIG_FIT
 321
 322 /* Framebuffer */
 323 #define CONFIG_VIDEO
 324 #define CONFIG_VIDEO_IPUV3
 325 /* check this console not needed, after test remove it */
 326 #define CONFIG_CFB_CONSOLE
 327 #define CONFIG_VGA_AS_SINGLE_DEVICE
 328 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 329 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 330 #define CONFIG_VIDEO_BMP_RLE8
 331 #define CONFIG_SPLASH_SCREEN
 332 #define CONFIG_SPLASH_SCREEN_ALIGN
 333 #define CONFIG_BMP_16BPP
 334 #define CONFIG_VIDEO_LOGO
 335 #define CONFIG_VIDEO_BMP_LOGO
 336 #define CONFIG_IPUV3_CLK 198000000
 337 #define CONFIG_IMX_VIDEO_SKIP
 338
 339 #define CONFIG_CMD_BMP
 340
 341 #define CONFIG_PWM_IMX
 342 #define CONFIG_IMX6_PWM_PER_CLK 66000000
 343 #endif                         /* __ARISTAINETOS_CONFIG_H */