include/configs/cm5200.h

   1 /*
   2  * (C) Copyright 2003-2007
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11
  12 #define CONFIG_SYS_GENERIC_BOARD
  13 #define CONFIG_DISPLAY_BOARDINFO
  14
  15
  16 /*
  17  * High Level Configuration Options
  18  */
  19 #define CONFIG_MPC5200          1       /* This is an MPC5200 CPU */
  20 #define CONFIG_CM5200           1       /* ... on CM5200 platform */
  21
  22 #define CONFIG_SYS_TEXT_BASE    0xfc000000
  23
  24 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  25
  26 /*
  27  * Supported commands
  28  */
  29 #define CONFIG_CMD_ASKENV
  30 #define CONFIG_CMD_BSP
  31 #define CONFIG_CMD_DATE
  32 #define CONFIG_CMD_DHCP
  33 #define CONFIG_CMD_DIAG
  34 #define CONFIG_CMD_FAT
  35 #define CONFIG_CMD_I2C
  36 #define CONFIG_CMD_JFFS2
  37 #define CONFIG_CMD_MII
  38 #define CONFIG_CMD_PING
  39 #define CONFIG_CMD_REGINFO
  40 #define CONFIG_CMD_SNTP
  41 #define CONFIG_CMD_USB
  42
  43 /*
  44  * Serial console configuration
  45  */
  46 #define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
  47 #define CONFIG_BAUDRATE         57600   /* ... at 57600 bps */
  48 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  49 #define CONFIG_SILENT_CONSOLE   1       /* needed to silence i2c_init() */
  50
  51 /*
  52  * Ethernet configuration
  53  */
  54 #define CONFIG_MPC5xxx_FEC      1
  55 #define CONFIG_MPC5xxx_FEC_MII100
  56 #define CONFIG_PHY_ADDR         0x00
  57 #define CONFIG_ENV_OVERWRITE    1       /* allow overwriting of ethaddr */
  58 /* use misc_init_r() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
  59 #define CONFIG_MISC_INIT_R      1
  60 #define CONFIG_MAC_OFFSET       0x35    /* MAC address offset in I2C EEPROM */
  61
  62 /*
  63  * POST support
  64  */
  65 #define CONFIG_POST             (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C)
  66 #define MPC5XXX_SRAM_POST_SIZE  (MPC5XXX_SRAM_SIZE - 4)
  67 /* List of I2C addresses to be verified by POST */
  68 #define CONFIG_SYS_POST_I2C_ADDRS       {CONFIG_SYS_I2C_SLAVE,  \
  69                                          CONFIG_SYS_I2C_IO,     \
  70                                          CONFIG_SYS_I2C_EEPROM}
  71
  72 /* display image timestamps */
  73 #define CONFIG_TIMESTAMP        1
  74
  75 /*
  76  * Autobooting
  77  */
  78 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
  79 #define CONFIG_PREBOOT  "echo;" \
  80         "echo Type \"run net_nfs_fdt\" to mount root filesystem over NFS;" \
  81         "echo"
  82 #undef CONFIG_BOOTARGS
  83
  84 /*
  85  * Default environment settings
  86  */
  87 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  88         "netdev=eth0\0"                                                 \
  89         "netmask=255.255.0.0\0"                                         \
  90         "ipaddr=192.168.160.33\0"                                       \
  91         "serverip=192.168.1.1\0"                                        \
  92         "gatewayip=192.168.1.1\0"                                       \
  93         "console=ttyPSC0\0"                                             \
  94         "u-boot_addr=100000\0"                                          \
  95         "kernel_addr=200000\0"                                          \
  96         "kernel_addr_flash=fc0c0000\0"                                  \
  97         "fdt_addr=400000\0"                                             \
  98         "fdt_addr_flash=fc0a0000\0"                                     \
  99         "ramdisk_addr=500000\0"                                         \
 100         "rootpath=/opt/eldk-4.1/ppc_6xx\0"                              \
 101         "u-boot=/tftpboot/cm5200/u-boot.bin\0"                          \
 102         "bootfile_fdt=/tftpboot/cm5200/uImage\0"                        \
 103         "fdt_file=/tftpboot/cm5200/cm5200.dtb\0"                        \
 104         "load=tftp ${u-boot_addr} ${u-boot}\0"                          \
 105         "update=prot off fc000000 +${filesize}; "                       \
 106                 "era fc000000 +${filesize}; "                           \
 107                 "cp.b ${u-boot_addr} fc000000 ${filesize}; "            \
 108                 "prot on fc000000 +${filesize}\0"                       \
 109         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 110                 "nfsroot=${serverip}:${rootpath}\0"                     \
 111         "flashargs=setenv bootargs root=/dev/mtdblock5 rw\0"            \
 112         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 113         "addinit=setenv bootargs ${bootargs} init=/linuxrc\0"           \
 114         "addcons=setenv bootargs ${bootargs} "                          \
 115                 "console=${console},${baudrate}\0"                      \
 116         "addip=setenv bootargs ${bootargs} "                            \
 117                 "ip=${ipaddr}:${serverip}:${gatewayip}:"                \
 118                 "${netmask}:${hostname}:${netdev}:off panic=1\0"        \
 119         "flash_flash=run flashargs addinit addip addcons;"              \
 120                 "bootm ${kernel_addr_flash} - ${fdt_addr_flash}\0"      \
 121         "net_nfs_fdt=tftp ${kernel_addr} ${bootfile_fdt}; "             \
 122                 "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip "      \
 123                 "addcons; bootm ${kernel_addr} - ${fdt_addr}\0"         \
 124         ""
 125 #define CONFIG_BOOTCOMMAND      "run flash_flash"
 126
 127 /*
 128  * Low level configuration
 129  */
 130
 131 /*
 132  * Clock configuration
 133  */
 134 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000        /* SYS_XTAL_IN = 33MHz */
 135 #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK 1       /* IPB = 133MHz */
 136
 137 /*
 138  * Memory map
 139  */
 140 #define CONFIG_SYS_MBAR         0xF0000000
 141 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 142 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 143
 144 #define CONFIG_SYS_LOWBOOT              1
 145
 146 /* Use ON-Chip SRAM until RAM will be available */
 147 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 148 #ifdef CONFIG_POST
 149 /* preserve space for the post_word at end of on-chip SRAM */
 150 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_POST_SIZE
 151 #else
 152 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_SIZE
 153 #endif
 154
 155 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 156 #define CONFIG_BOARD_TYPES      1       /* we use board_type */
 157
 158 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 159
 160 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
 161 #define CONFIG_SYS_MONITOR_LEN          (384 << 10)     /* 384 kB for Monitor */
 162 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* 256 kB for malloc() */
 163 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* initial mem map for Linux */
 164
 165 /*
 166  * Flash configuration
 167  */
 168 #define CONFIG_SYS_FLASH_CFI            1
 169 #define CONFIG_FLASH_CFI_DRIVER 1
 170 #define CONFIG_SYS_FLASH_BASE           0xfc000000
 171 /* we need these despite using CFI */
 172 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of flash banks */
 173 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max num of sectors on one chip */
 174 #define CONFIG_SYS_FLASH_SIZE           0x02000000 /* 32 MiB */
 175
 176
 177 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 178 #define CONFIG_SYS_RAMBOOT              1
 179 #undef CONFIG_SYS_LOWBOOT
 180 #endif
 181
 182
 183 /*
 184  * Chip selects configuration
 185  */
 186 /* Boot Chipselect */
 187 #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
 188 #define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
 189 #define CONFIG_SYS_BOOTCS_CFG           0x00087D31      /* for pci_clk = 33 MHz */
 190 /* use board_early_init_r to enable flash write in CS_BOOT */
 191 #define CONFIG_BOARD_EARLY_INIT_R
 192
 193 /* Flash memory addressing */
 194 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 195 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 196
 197 /* No burst, dead cycle = 1 for CS0 (Flash) */
 198 #define CONFIG_SYS_CS_BURST             0x00000000
 199 #define CONFIG_SYS_CS_DEADCYCLE 0x00000001
 200
 201 /*
 202  * SDRAM configuration
 203  * settings for k4s561632E-xx75, assuming XLB = 132 MHz
 204  */
 205 #define SDRAM_MODE      0x00CD0000      /* CASL 3, burst length 8 */
 206 #define SDRAM_CONTROL   0x514F0000
 207 #define SDRAM_CONFIG1   0xE2333900
 208 #define SDRAM_CONFIG2   0x8EE70000
 209
 210 /*
 211  * MTD configuration
 212  */
 213 #define CONFIG_CMD_MTDPARTS     1
 214 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 215 #define CONFIG_FLASH_CFI_MTD
 216 #define MTDIDS_DEFAULT          "nor0=cm5200-0"
 217 #define MTDPARTS_DEFAULT        "mtdparts=cm5200-0:"                    \
 218                                         "384k(uboot),128k(env),"        \
 219                                         "128k(redund_env),128k(dtb),"   \
 220                                         "2m(kernel),27904k(rootfs),"    \
 221                                         "-(config)"
 222
 223 /*
 224  * I2C configuration
 225  */
 226 #define CONFIG_HARD_I2C         1       /* I2C with hardware support */
 227 #define CONFIG_SYS_I2C_MODULE           2       /* Select I2C module #2 */
 228 #define CONFIG_SYS_I2C_SPEED            40000   /* 40 kHz */
 229 #define CONFIG_SYS_I2C_SLAVE            0x0
 230 #define CONFIG_SYS_I2C_IO               0x38    /* PCA9554AD I2C I/O port address */
 231 #define CONFIG_SYS_I2C_EEPROM           0x53    /* I2C EEPROM device address */
 232
 233 /*
 234  * RTC configuration
 235  */
 236 #define CONFIG_RTC_MPC5200      1       /* use internal MPC5200 RTC */
 237
 238 /*
 239  * USB configuration
 240  */
 241 #define CONFIG_USB_OHCI         1
 242 #define CONFIG_USB_STORAGE      1
 243 #define CONFIG_USB_CLOCK        0x0001BBBB
 244 #define CONFIG_USB_CONFIG       0x00001000
 245 /* Partitions (for USB) */
 246 #define CONFIG_MAC_PARTITION    1
 247 #define CONFIG_DOS_PARTITION    1
 248 #define CONFIG_ISO_PARTITION    1
 249
 250 /*
 251  * Invoke our last_stage_init function - needed by fwupdate
 252  */
 253 #define CONFIG_LAST_STAGE_INIT  1
 254
 255 /*
 256  * Environment settings
 257  */
 258 #define CONFIG_ENV_IS_IN_FLASH  1
 259 #define CONFIG_ENV_SIZE         0x10000
 260 #define CONFIG_ENV_SECT_SIZE    0x20000
 261 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
 262 /* Configuration of redundant environment */
 263 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 264 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 265
 266 /*
 267  * Pin multiplexing configuration
 268  */
 269
 270 /*
 271  * CS1/GPIO_WKUP_6: GPIO (default)
 272  * ALTs: CAN1 on I2C1, CAN2 on TIMER0/1
 273  * IRDA/PSC6: UART
 274  * Ether: Ethernet 100Mbit with MD
 275  * PCI_DIS: PCI controller disabled
 276  * USB: USB
 277  * PSC3: SPI with UART3
 278  * PSC2: UART
 279  * PSC1: UART
 280  */
 281 #define CONFIG_SYS_GPS_PORT_CONFIG      0x10559C44
 282
 283 /*
 284  * Miscellaneous configurable options
 285  */
 286 #define CONFIG_SYS_LONGHELP             1       /* undef to save memory */
 287 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 288 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 289 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 290 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 291
 292 #define CONFIG_SYS_ALT_MEMTEST          1
 293 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 294 #define CONFIG_SYS_MEMTEST_END          0x03f00000      /* 1 .. 63 MiB in SDRAM */
 295
 296 #define CONFIG_LOOPW            1
 297
 298 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 299
 300 /*
 301  * Various low-level settings
 302  */
 303 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 304 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 305
 306 #define CONFIG_SYS_XLB_PIPELINING       1       /* enable transaction pipeling */
 307
 308 /*
 309  * Cache Configuration
 310  */
 311 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 312 #ifdef CONFIG_CMD_KGDB
 313 #define CONFIG_SYS_CACHELINE_SHIFT      5       /* log base 2 of the above value */
 314 #endif
 315
 316 /*
 317  * Flat Device Tree support
 318  */
 319 #define CONFIG_OF_LIBFDT        1
 320 #define CONFIG_OF_BOARD_SETUP   1
 321 #define OF_CPU                  "PowerPC,5200@0"
 322 #define OF_SOC                  "soc5200@f0000000"
 323 #define OF_TBCLK                (bd->bi_busfreq / 4)
 324 #define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"
 325
 326 #endif /* __CONFIG_H */