include/configs/cm_fx6.h

   1 /*
   2  * Config file for Compulab CM-FX6 board
   3  *
   4  * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
   5  *
   6  * Author: Nikita Kiryanov <nikita@compulab.co.il>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_CM_FX6_H
  12 #define __CONFIG_CM_FX6_H
  13
  14 #include <asm/arch/imx-regs.h>
  15 #include <config_distro_defaults.h>
  16 #include "mx6_common.h"
  17
  18 /* Machine config */
  19 #define CONFIG_MX6
  20 #define CONFIG_SYS_LITTLE_ENDIAN
  21 #define CONFIG_MACH_TYPE                4273
  22
  23 #ifndef CONFIG_SPL_BUILD
  24 #define CONFIG_DM
  25 #define CONFIG_CMD_DM
  26
  27 #define CONFIG_DM_GPIO
  28 #define CONFIG_CMD_GPIO
  29
  30 #define CONFIG_DM_SERIAL
  31 #define CONFIG_SYS_MALLOC_F_LEN         (1 << 10)
  32 #endif
  33
  34 /* Display information on boot */
  35 #define CONFIG_DISPLAY_CPUINFO
  36 #define CONFIG_DISPLAY_BOARDINFO
  37 #define CONFIG_TIMESTAMP
  38
  39 /* CMD */
  40 #include <config_cmd_default.h>
  41 #define CONFIG_CMD_GREPENV
  42 #undef CONFIG_CMD_FLASH
  43 #undef CONFIG_CMD_LOADB
  44 #undef CONFIG_CMD_LOADS
  45 #undef CONFIG_CMD_XIMG
  46 #undef CONFIG_CMD_FPGA
  47 #undef CONFIG_CMD_IMLS
  48
  49 /* MMC */
  50 #define CONFIG_MMC
  51 #define CONFIG_CMD_MMC
  52 #define CONFIG_GENERIC_MMC
  53 #define CONFIG_FSL_ESDHC
  54 #define CONFIG_FSL_USDHC
  55 #define CONFIG_SYS_FSL_USDHC_NUM        3
  56 #define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC2_BASE_ADDR
  57
  58 /* RAM */
  59 #define PHYS_SDRAM_1                    MMDC0_ARB_BASE_ADDR
  60 #define PHYS_SDRAM_2                    MMDC1_ARB_BASE_ADDR
  61 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
  62 #define CONFIG_NR_DRAM_BANKS            2
  63 #define CONFIG_SYS_MEMTEST_START        0x10000000
  64 #define CONFIG_SYS_MEMTEST_END          0x10010000
  65 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
  66 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
  67 #define CONFIG_SYS_INIT_SP_OFFSET \
  68         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
  69 #define CONFIG_SYS_INIT_SP_ADDR \
  70         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
  71
  72 /* Serial console */
  73 #define CONFIG_MXC_UART
  74 #define CONFIG_MXC_UART_BASE            UART4_BASE
  75 #define CONFIG_BAUDRATE                 115200
  76 #define CONFIG_SYS_BAUDRATE_TABLE       {9600, 19200, 38400, 57600, 115200}
  77
  78 /* Shell */
  79 #define CONFIG_SYS_PROMPT       "CM-FX6 # "
  80 #define CONFIG_SYS_CBSIZE       1024
  81 #define CONFIG_SYS_MAXARGS      16
  82 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
  83 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
  84                                         sizeof(CONFIG_SYS_PROMPT) + 16)
  85
  86 /* SPI flash */
  87 #define CONFIG_SYS_NO_FLASH
  88 #define CONFIG_CMD_SF
  89 #define CONFIG_SF_DEFAULT_BUS           0
  90 #define CONFIG_SF_DEFAULT_CS            0
  91 #define CONFIG_SF_DEFAULT_SPEED         25000000
  92 #define CONFIG_SF_DEFAULT_MODE          (SPI_MODE_0)
  93
  94 /* Environment */
  95 #define CONFIG_ENV_OVERWRITE
  96 #define CONFIG_ENV_IS_IN_SPI_FLASH
  97 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
  98 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
  99 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 100 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 101 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 102 #define CONFIG_ENV_SIZE                 (8 * 1024)
 103 #define CONFIG_ENV_OFFSET               (768 * 1024)
 104
 105 #define CONFIG_EXTRA_ENV_SETTINGS \
 106         "kernel=uImage-cm-fx6\0" \
 107         "autoload=no\0" \
 108         "loadaddr=0x10800000\0" \
 109         "fdtaddr=0x11000000\0" \
 110         "console=ttymxc3,115200\0" \
 111         "ethprime=FEC0\0" \
 112         "bootscr=boot.scr\0" \
 113         "bootm_low=18000000\0" \
 114         "video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \
 115         "video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \
 116         "fdtfile=cm-fx6.dtb\0" \
 117         "doboot=bootm ${loadaddr}\0" \
 118         "loadfdt=false\0" \
 119         "setboottypez=setenv kernel zImage-cm-fx6;" \
 120                 "setenv doboot bootz ${loadaddr} - ${fdtaddr};" \
 121                 "setenv loadfdt true;\0" \
 122         "setboottypem=setenv kernel uImage-cm-fx6;" \
 123                 "setenv doboot bootm ${loadaddr};" \
 124                 "setenv loadfdt false;\0"\
 125         "run_eboot=echo Starting EBOOT ...; "\
 126                 "mmc dev ${mmcdev} && " \
 127                 "mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \
 128         "mmcdev=2\0" \
 129         "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
 130         "loadmmcbootscript=load mmc ${mmcdev} ${loadaddr} ${bootscr}\0" \
 131         "mmcbootscript=echo Running bootscript from mmc ...; "\
 132                 "source ${loadaddr}\0" \
 133         "mmcargs=setenv bootargs console=${console} " \
 134                 "root=${mmcroot} " \
 135                 "${video}\0" \
 136         "mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
 137         "mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
 138         "mmcboot=echo Booting from mmc ...; " \
 139                 "run mmcargs; " \
 140                 "run doboot\0" \
 141         "satadev=0\0" \
 142         "sataroot=/dev/sda2 rw rootwait\0" \
 143         "sataargs=setenv bootargs console=${console} " \
 144                 "root=${sataroot} " \
 145                 "${video}\0" \
 146         "loadsatabootscript=load sata ${satadev} ${loadaddr} ${bootscr}\0" \
 147         "satabootscript=echo Running bootscript from sata ...; " \
 148                 "source ${loadaddr}\0" \
 149         "sataloadkernel=load sata ${satadev} ${loadaddr} ${kernel}\0" \
 150         "sataloadfdt=load sata ${satadev} ${fdtaddr} ${fdtfile}\0" \
 151         "sataboot=echo Booting from sata ...; "\
 152                 "run sataargs; " \
 153                 "run doboot\0" \
 154         "nandroot=/dev/mtdblock4 rw\0" \
 155         "nandrootfstype=ubifs\0" \
 156         "nandargs=setenv bootargs console=${console} " \
 157                 "root=${nandroot} " \
 158                 "rootfstype=${nandrootfstype} " \
 159                 "${video}\0" \
 160         "nandloadfdt=nand read ${fdtaddr} 780000 80000;\0" \
 161         "nandboot=echo Booting from nand ...; " \
 162                 "run nandargs; " \
 163                 "nand read ${loadaddr} 0 780000; " \
 164                 "if ${loadfdt}; then " \
 165                         "run nandloadfdt;" \
 166                 "fi; " \
 167                 "run doboot\0" \
 168         "boot=mmc dev ${mmcdev}; " \
 169                 "if mmc rescan; then " \
 170                         "if run loadmmcbootscript; then " \
 171                                 "run mmcbootscript;" \
 172                         "else " \
 173                                 "if run mmcloadkernel; then " \
 174                                         "if ${loadfdt}; then " \
 175                                                 "run mmcloadfdt;" \
 176                                         "fi;" \
 177                                         "run mmcboot;" \
 178                                 "fi;" \
 179                         "fi;" \
 180                 "fi;" \
 181                 "if sata init; then " \
 182                         "if run loadsatabootscript; then " \
 183                                 "run satabootscript;" \
 184                         "else "\
 185                                 "if run sataloadkernel; then " \
 186                                         "if ${loadfdt}; then " \
 187                                                 "run sataloadfdt; " \
 188                                         "fi;" \
 189                                         "run sataboot;" \
 190                                 "fi;" \
 191                         "fi;" \
 192                 "fi;" \
 193                 "run nandboot\0"
 194
 195 #define CONFIG_BOOTCOMMAND \
 196         "run setboottypem; run boot"
 197
 198 /* SPI */
 199 #define CONFIG_SPI
 200 #define CONFIG_MXC_SPI
 201 #define CONFIG_SPI_FLASH
 202 #define CONFIG_SPI_FLASH_ATMEL
 203 #define CONFIG_SPI_FLASH_EON
 204 #define CONFIG_SPI_FLASH_GIGADEVICE
 205 #define CONFIG_SPI_FLASH_MACRONIX
 206 #define CONFIG_SPI_FLASH_SPANSION
 207 #define CONFIG_SPI_FLASH_STMICRO
 208 #define CONFIG_SPI_FLASH_SST
 209 #define CONFIG_SPI_FLASH_WINBOND
 210
 211 /* NAND */
 212 #ifndef CONFIG_SPL_BUILD
 213 #define CONFIG_CMD_NAND
 214 #define CONFIG_SYS_NAND_BASE            0x40000000
 215 #define CONFIG_SYS_NAND_MAX_CHIPS       1
 216 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 217 #define CONFIG_NAND_MXS
 218 #define CONFIG_SYS_NAND_ONFI_DETECTION
 219 /* APBH DMA is required for NAND support */
 220 #define CONFIG_APBH_DMA
 221 #define CONFIG_APBH_DMA_BURST
 222 #define CONFIG_APBH_DMA_BURST8
 223 #endif
 224
 225 /* Ethernet */
 226 #define CONFIG_FEC_MXC
 227 #define CONFIG_FEC_MXC_PHYADDR          0
 228 #define CONFIG_FEC_XCV_TYPE             RGMII
 229 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 230 #define CONFIG_PHYLIB
 231 #define CONFIG_PHY_ATHEROS
 232 #define CONFIG_MII
 233 #define CONFIG_ETHPRIME                 "FEC0"
 234 #define CONFIG_ARP_TIMEOUT              200UL
 235 #define CONFIG_NET_RETRY_COUNT          5
 236
 237 /* USB */
 238 #define CONFIG_CMD_USB
 239 #define CONFIG_USB_EHCI
 240 #define CONFIG_USB_EHCI_MX6
 241 #define CONFIG_USB_STORAGE
 242 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
 243 #define CONFIG_MXC_USB_FLAGS            0
 244 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 245 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 246
 247 /* I2C */
 248 #define CONFIG_CMD_I2C
 249 #define CONFIG_SYS_I2C
 250 #define CONFIG_SYS_I2C_MXC
 251 #define CONFIG_SYS_I2C_SPEED            100000
 252 #define CONFIG_SYS_MXC_I2C3_SPEED       400000
 253
 254 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 255 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 256 #define CONFIG_SYS_I2C_EEPROM_BUS       2
 257
 258 /* SATA */
 259 #define CONFIG_CMD_SATA
 260 #define CONFIG_SYS_SATA_MAX_DEVICE      1
 261 #define CONFIG_LIBATA
 262 #define CONFIG_LBA48
 263 #define CONFIG_DWC_AHSATA
 264 #define CONFIG_DWC_AHSATA_PORT_ID       0
 265 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
 266
 267 /* GPIO */
 268 #define CONFIG_MXC_GPIO
 269
 270 /* Boot */
 271 #define CONFIG_ZERO_BOOTDELAY_CHECK
 272 #define CONFIG_LOADADDR                 0x10800000
 273 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 274 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
 275 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)
 276 #define CONFIG_SETUP_MEMORY_TAGS
 277 #define CONFIG_INITRD_TAG
 278 #define CONFIG_REVISION_TAG
 279 #define CONFIG_SERIAL_TAG
 280
 281 /* misc */
 282 #define CONFIG_SYS_GENERIC_BOARD
 283 #define CONFIG_STACKSIZE                        (128 * 1024)
 284 #define CONFIG_SYS_MALLOC_LEN                   (2 * 1024 * 1024)
 285 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      800 /* 400 KB */
 286 #define CONFIG_OF_BOARD_SETUP
 287
 288 /* SPL */
 289 #include "imx6_spl.h"
 290 #define CONFIG_SPL_BOARD_INIT
 291 #define CONFIG_SPL_MMC_SUPPORT
 292 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x80 /* offset 64 kb */
 293 #define CONFIG_SYS_MONITOR_LEN  (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS / 2 * 1024)
 294 #define CONFIG_SPL_SPI_SUPPORT
 295 #define CONFIG_SPL_SPI_FLASH_SUPPORT
 296 #define CONFIG_SYS_SPI_U_BOOT_OFFS      (64 * 1024)
 297 #define CONFIG_SPL_SPI_LOAD
 298
 299 #endif  /* __CONFIG_CM_FX6_H */