- at32ap Files specific to Atmel AVR32 AP CPUs
- i386 Files specific to i386 CPUs
- ixp Files specific to Intel XScale IXP CPUs
+ - leon2 Files specific to Gaisler LEON2 SPARC CPU
+ - leon3 Files specific to Gaisler LEON3 SPARC CPU
- mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
- mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
- mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
- lib_mips Files generic to MIPS architecture
- lib_nios Files generic to NIOS architecture
- lib_ppc Files generic to PowerPC architecture
+- lib_sparc Files generic to SPARC architecture
- libfdt Library files to support flattened device trees
- net Networking code
- post Power On Self Test
boards with QUICC Engines require OF_QE to set UCC mac addresses
- CONFIG_OF_HAS_BD_T
-
- * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
- * CONFIG_OF_FLAT_TREE - The resulting flat device tree
- will have a copy of the bd_t. Space should be
- pre-allocated in the dts for the bd_t.
-
- CONFIG_OF_HAS_UBOOT_ENV
-
- * CONFIG_OF_LIBFDT - enables the "fdt env" command
- * CONFIG_OF_FLAT_TREE - The resulting flat device tree
- will have a copy of u-boot's environment variables
-
CONFIG_OF_BOARD_SETUP
Board code has addition modification that it wants to make
CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
+ CONFIG_RTC_MC13783 - use MC13783 RTC
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
Currently supported on some MPC8xxx processors. For an
example, see include/configs/mpc8349emds.h.
+ CONFIG_MXC_SPI
+
+ Enables the driver for the SPI controllers on i.MX and MXC
+ SoCs. Currently only i.MX31 is supported.
+
- FPGA Support: CONFIG_FPGA
Enables FPGA subsystem.
Scratch address used by the alternate memory test
You only need to set this if address zero isn't writeable
+- CFG_MEM_TOP_HIDE (PPC only):
+ If CFG_MEM_TOP_HIDE is defined in the board config header,
+ this specified memory area will get subtracted from the top
+ (end) of ram and won't get "touched" at all by U-Boot. By
+ fixing up gd->ram_size the Linux kernel should gets passed
+ the now "corrected" memory size and won't touch it either.
+ This should work for arch/ppc and arch/powerpc. Only Linux
+ board ports in arch/powerpc with bootwrapper support that
+ recalculate the memory size from the SDRAM controller setup
+ will have to get fixed in Linux additionally.
+
+ This option can be used as a workaround for the 440EPx/GRx
+ CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
+ be touched.
+
+ WARNING: Please make sure that this value is a multiple of
+ the Linux page size (normally 4k). If this is not the case,
+ then the end address of the Linux memory will be located at a
+ non page size aligned address and this could cause major
+ problems.
+
- CFG_TFTP_LOADADDR:
Default load address for network file downloads
- CFG_BOOTMAPSZ:
Maximum size of memory mapped by the startup code of
the Linux kernel; all data that must be processed by
- the Linux kernel (bd_info, boot arguments, eventually
- initrd image) must be put below this limit.
+ the Linux kernel (bd_info, boot arguments, FDT blob if
+ used) must be put below this limit, unless "bootm_low"
+ enviroment variable is defined and non-zero. In such case
+ all data for the Linux kernel must be between "bootm_low"
+ and "bootm_low" + CFG_BOOTMAPSZ.
- CFG_MAX_FLASH_BANKS:
Max number of Flash memory banks
This option also enables the building of the cfi_flash driver
in the drivers directory
+- CFG_FLASH_USE_BUFFER_WRITE
+ Use buffered writes to flash.
+
+- CONFIG_FLASH_SPANSION_S29WS_N
+ s29ws-n MirrorBit flash has non-standard addresses for buffered
+ write commands.
+
- CFG_FLASH_QUIET_TEST
If this option is defined, the common CFI flash doesn't
print it's warning upon not recognized FLASH banks. This
bootfile - Name of the image to load with TFTP
+ bootm_low - Memory range available for image processing in the bootm
+ command can be restricted. This variable is given as
+ a hexadecimal number and defines lowest address allowed
+ for use by the bootm command. See also "bootm_size"
+ environment variable. Address defined by "bootm_low" is
+ also the base of the initial memory mapping for the Linux
+ kernel -- see the descripton of CFG_BOOTMAPSZ.
+
+ bootm_size - Memory range available for image processing in the bootm
+ command can be restricted. This variable is given as
+ a hexadecimal number and defines the size of the region
+ allowed for use by the bootm command. See also "bootm_low"
+ environment variable.
+
autoload - if set to "no" (any string beginning with 'n'),
"bootp" will just load perform a lookup of the
configuration from the BOOTP server, but not try to
projects / karo-tx-uboot.git / blobdiff