Files specific to EVB64260 boards
- board/fads Files specific to FADS boards
- board/flagadm Files specific to FLAGADM boards
-- board/gen860t Files specific to GEN860T boards
+- board/gen860t Files specific to GEN860T and GEN860T_SC boards
- board/genietv Files specific to GENIETV boards
- board/gth Files specific to GTH boards
- board/hermes Files specific to HERMES boards
CONFIG_GTH, CONFIG_RPXClassic, CONFIG_rsdproto,
CONFIG_IAD210, CONFIG_RPXlite, CONFIG_sbc8260,
CONFIG_EBONY, CONFIG_sacsng, CONFIG_FPS860L,
- CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI
+ CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI,
+ CONFIG_NETVIA
ARM based boards:
-----------------
Set to 0 to disable this feature (this is the default).
This will also disable hardware handshake.
+- Console UART Number:
+ CONFIG_UART1_CONSOLE
+
+ IBM PPC4xx only.
+ If defined internal UART1 (and not UART0) is used
+ as default U-Boot console.
+
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
CONFIG_RTC_MC146818 - use MC146818 RTC
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
+ CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
- Timestamp Support:
CONFIG_NS8382X
Support for National dp8382[01] gigabit chips.
+- NETWORK Support (other):
+
+ CONFIG_DRIVER_LAN91C96
+ Support for SMSC's LAN91C96 chips.
+
+ CONFIG_LAN91C96_BASE
+ Define this to hold the physical address
+ of the LAN91C96's I/O space
+
+ CONFIG_LAN91C96_USE_32_BIT
+ Define this to enable 32 bit addressing
+
- USB Support:
At the moment only the UHCI host controller is
supported (PIP405, MIP405); define
#define'd default value in commproc.h resp.
cpm_8260.h.
+- CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
+ CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
+ CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
+ CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
+ CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
+ CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
+ CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
+ CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
+ Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
+
Building the Software:
======================
FPS850L_config Sandpoint8240_config sbc8260_config
GENIETV_config TQM823L_config PIP405_config
GEN860T_config EBONY_config FPS860L_config
- ELPT860_config cmi_mpc5xx_config
+ ELPT860_config cmi_mpc5xx_config NETVIA_config
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for
setenv initrd_high 00c00000
+ If you set initrd_high to 0xFFFFFFFF, this is an
+ indication to U-Boot that all addresses are legal
+ for the Linux kernel, including addresses in flash
+ memory. In this case U-Boot will NOT COPY the
+ ramdisk at all. This may be useful to reduce the
+ boot time on your system, but requires that this
+ feature is supported by your Linux kernel.
+
ipaddr - IP address; needed for tftpboot command
loadaddr - Default load address for commands like "bootp",
* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
- LynxOS, pSOS, QNX;
- Currently supported: Linux, NetBSD, VxWorks, QNX).
+ LynxOS, pSOS, QNX, RTEMS, ARTOS;
+ Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS).
* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
IA64, MIPS, MIPS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
Currently supported: PowerPC).