--- /dev/null
+/*
+ * DDR3 mem setup file for SMDK5250 board based on EXYNOS5
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dmc.h>
+#include "common_setup.h"
+#include "exynos5_setup.h"
+#include "clock_init.h"
+
+#define RDLVL_COMPLETE_TIMEOUT 10000
+
+static void reset_phy_ctrl(void)
+{
+ struct exynos5_clock *clk =
+ (struct exynos5_clock *)samsung_get_base_clock();
+
+ writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
+ writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
+}
+
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
+ int reset)
+{
+ unsigned int val;
+ struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
+ struct exynos5_dmc *dmc;
+ int i;
+
+ phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy();
+ phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy()
+ + DMC_OFFSET);
+ dmc = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl();
+
+ if (reset)
+ reset_phy_ctrl();
+
+ /* Set Impedance Output Driver */
+ val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
+ (mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
+ (mem->impedance << CA_CS_DRVR_DS_OFFSET) |
+ (mem->impedance << CA_ADR_DRVR_DS_OFFSET);
+ writel(val, &phy0_ctrl->phy_con39);
+ writel(val, &phy1_ctrl->phy_con39);
+
+ /* Set Read Latency and Burst Length for PHY0 and PHY1 */
+ val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
+ (mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
+ writel(val, &phy0_ctrl->phy_con42);
+ writel(val, &phy1_ctrl->phy_con42);
+
+ /* ZQ Calibration */
+ if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
+ return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
+
+ /* DQ Signal */
+ writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
+ writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
+
+ writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+ | (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
+ &dmc->concontrol);
+
+ update_reset_dll(dmc, DDR_MODE_DDR3);
+
+ /* DQS Signal */
+ writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
+ writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
+
+ writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
+ writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
+
+ writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
+ writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
+
+ val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
+ (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+ (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+ (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ /* Start DLL locking */
+ writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+ &phy0_ctrl->phy_con12);
+ writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+ &phy1_ctrl->phy_con12);
+
+ update_reset_dll(dmc, DDR_MODE_DDR3);
+
+ writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
+ &dmc->concontrol);
+
+ /* Memory Channel Inteleaving Size */
+ writel(mem->iv_size, &dmc->ivcontrol);
+
+ writel(mem->memconfig, &dmc->memconfig0);
+ writel(mem->memconfig, &dmc->memconfig1);
+ writel(mem->membaseconfig0, &dmc->membaseconfig0);
+ writel(mem->membaseconfig1, &dmc->membaseconfig1);
+
+ /* Precharge Configuration */
+ writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
+ &dmc->prechconfig);
+
+ /* Power Down mode Configuration */
+ writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
+ mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
+ &dmc->pwrdnconfig);
+
+ /* TimingRow, TimingData, TimingPower and Timingaref
+ * values as per Memory AC parameters
+ */
+ writel(mem->timing_ref, &dmc->timingref);
+ writel(mem->timing_row, &dmc->timingrow);
+ writel(mem->timing_data, &dmc->timingdata);
+ writel(mem->timing_power, &dmc->timingpower);
+
+ /* Send PALL command */
+ dmc_config_prech(mem, dmc);
+
+ /* Send NOP, MRS and ZQINIT commands */
+ dmc_config_mrs(mem, dmc);
+
+ if (mem->gate_leveling_enable) {
+ val = PHY_CON0_RESET_VAL;
+ val |= P0_CMD_EN;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ val = PHY_CON2_RESET_VAL;
+ val |= INIT_DESKEW_EN;
+ writel(val, &phy0_ctrl->phy_con2);
+ writel(val, &phy1_ctrl->phy_con2);
+
+ val = PHY_CON0_RESET_VAL;
+ val |= P0_CMD_EN;
+ val |= BYTE_RDLVL_EN;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ val = (mem->ctrl_start_point <<
+ PHY_CON12_CTRL_START_POINT_SHIFT) |
+ (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+ (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+ (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+ (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ val = PHY_CON2_RESET_VAL;
+ val |= INIT_DESKEW_EN;
+ val |= RDLVL_GATE_EN;
+ writel(val, &phy0_ctrl->phy_con2);
+ writel(val, &phy1_ctrl->phy_con2);
+
+ val = PHY_CON0_RESET_VAL;
+ val |= P0_CMD_EN;
+ val |= BYTE_RDLVL_EN;
+ val |= CTRL_SHGATE;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ val = PHY_CON1_RESET_VAL;
+ val &= ~(CTRL_GATEDURADJ_MASK);
+ writel(val, &phy0_ctrl->phy_con1);
+ writel(val, &phy1_ctrl->phy_con1);
+
+ writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
+ i = RDLVL_COMPLETE_TIMEOUT;
+ while ((readl(&dmc->phystatus) &
+ (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
+ (RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
+ /*
+ * TODO(waihong): Comment on how long this take to
+ * timeout
+ */
+ sdelay(100);
+ i--;
+ }
+ if (!i)
+ return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+ writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
+
+ writel(0, &phy0_ctrl->phy_con14);
+ writel(0, &phy1_ctrl->phy_con14);
+
+ val = (mem->ctrl_start_point <<
+ PHY_CON12_CTRL_START_POINT_SHIFT) |
+ (mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+ (mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+ (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+ (mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+ (mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ update_reset_dll(dmc, DDR_MODE_DDR3);
+ }
+
+ /* Send PALL command */
+ dmc_config_prech(mem, dmc);
+
+ writel(mem->memcontrol, &dmc->memcontrol);
+
+ /* Set DMC Concontrol and enable auto-refresh counter */
+ writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+ | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
+ return 0;
+}
projects / karo-tx-uboot.git / blobdiff