+++ /dev/null
-/*
- * serial.h - common serial defines for early debug and serial driver.
- * any functions defined here must be always_inline since
- * initcode cannot have function calls.
- *
- * Copyright (c) 2004-2007 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
-
-#ifndef __BFIN_CPU_SERIAL_H__
-#define __BFIN_CPU_SERIAL_H__
-
-#include <asm/blackfin.h>
-#include <asm/mach-common/bits/uart.h>
-
-#ifndef CONFIG_UART_CONSOLE
-# define CONFIG_UART_CONSOLE 0
-#endif
-
-#ifdef CONFIG_DEBUG_EARLY_SERIAL
-# define BFIN_DEBUG_EARLY_SERIAL 1
-#else
-# define BFIN_DEBUG_EARLY_SERIAL 0
-#endif
-
-#ifndef __ASSEMBLY__
-
-#include <asm/portmux.h>
-
-#define LOB(x) ((x) & 0xFF)
-#define HIB(x) (((x) >> 8) & 0xFF)
-
-#if defined(__ADSPBF50x__) || defined(__ADSPBF54x__)
-# define BFIN_UART_HW_VER 2
-#else
-# define BFIN_UART_HW_VER 1
-#endif
-
-/*
- * All Blackfin system MMRs are padded to 32bits even if the register
- * itself is only 16bits. So use a helper macro to streamline this.
- */
-#define __BFP(m) u16 m; u16 __pad_##m
-struct bfin_mmr_serial {
-#if BFIN_UART_HW_VER == 2
- __BFP(dll);
- __BFP(dlh);
- __BFP(gctl);
- __BFP(lcr);
- __BFP(mcr);
- __BFP(lsr);
- __BFP(msr);
- __BFP(scr);
- __BFP(ier_set);
- __BFP(ier_clear);
- __BFP(thr);
- __BFP(rbr);
-#else
- union {
- u16 dll;
- u16 thr;
- const u16 rbr;
- };
- const u16 __spad0;
- union {
- u16 dlh;
- u16 ier;
- };
- const u16 __spad1;
- const __BFP(iir);
- __BFP(lcr);
- __BFP(mcr);
- __BFP(lsr);
- __BFP(msr);
- __BFP(scr);
- const u32 __spad2;
- __BFP(gctl);
-#endif
-};
-#undef __BFP
-
-#define __PASTE_UART(num, pfx, sfx) pfx##num##_##sfx
-#define _PASTE_UART(num, pfx, sfx) __PASTE_UART(num, pfx, sfx)
-#define MMR_UART(n) _PASTE_UART(n, UART, DLL)
-#define _P_UART(n, pin) _PASTE_UART(n, P_UART, pin)
-#define P_UART(pin) _P_UART(CONFIG_UART_CONSOLE, pin)
-
-#ifndef UART_DLL
-# define UART_DLL MMR_UART(CONFIG_UART_CONSOLE)
-#else
-# define UART0_DLL UART_DLL
-# if CONFIG_UART_CONSOLE != 0
-# error CONFIG_UART_CONSOLE must be 0 on parts with only one UART
-# endif
-#endif
-#define pUART ((volatile struct bfin_mmr_serial *)uart_base)
-
-#if BFIN_UART_HW_VER == 2
-# define ACCESS_LATCH()
-# define ACCESS_PORT_IER()
-#else
-# define ACCESS_LATCH() \
- bfin_write(&pUART->lcr, bfin_read(&pUART->lcr) | DLAB)
-# define ACCESS_PORT_IER() \
- bfin_write(&pUART->lcr, bfin_read(&pUART->lcr) & ~DLAB)
-#endif
-
-__attribute__((always_inline))
-static inline void serial_do_portmux(void)
-{
- if (!BFIN_DEBUG_EARLY_SERIAL) {
- const unsigned short pins[] = { P_UART(RX), P_UART(TX), 0, };
- peripheral_request_list(pins, "bfin-uart");
- return;
- }
-
-#if defined(__ADSPBF50x__)
-# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \
- bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | PORT_x_MUX_##mux_tx##_FUNC_1 | PORT_x_MUX_##mux_rx##_FUNC_1); \
- bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
- switch (CONFIG_UART_CONSOLE) {
- case 0: DO_MUX(G, 7, 7, 12, 13); break; /* Port G; mux 7; PG12 and PG13 */
- case 1: DO_MUX(F, 3, 3, 6, 7); break; /* Port F; mux 3; PF6 and PF7 */
- }
- SSYNC();
-#elif defined(__ADSPBF51x__)
-# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \
- bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | PORT_x_MUX_##mux_tx##_FUNC_2 | PORT_x_MUX_##mux_rx##_FUNC_2); \
- bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
- switch (CONFIG_UART_CONSOLE) {
- case 0: DO_MUX(G, 5, 5, 9, 10); break; /* Port G; mux 5; PG9 and PG10 */
- case 1: DO_MUX(F, 2, 3, 14, 15); break; /* Port H; mux 2/3; PH14 and PH15 */
- }
- SSYNC();
-#elif defined(__ADSPBF52x__)
-# define DO_MUX(port, mux, tx, rx) \
- bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~PORT_x_MUX_##mux##_MASK) | PORT_x_MUX_##mux##_FUNC_3); \
- bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
- switch (CONFIG_UART_CONSOLE) {
- case 0: DO_MUX(G, 2, 7, 8); break; /* Port G; mux 2; PG2 and PG8 */
- case 1: DO_MUX(F, 5, 14, 15); break; /* Port F; mux 5; PF14 and PF15 */
- }
- SSYNC();
-#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__)
- const uint16_t func[] = { PFDE, PFTE, };
- bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~func[CONFIG_UART_CONSOLE]);
- bfin_write_PORTF_FER(bfin_read_PORTF_FER() |
- (1 << P_IDENT(P_UART(RX))) |
- (1 << P_IDENT(P_UART(TX))));
- SSYNC();
-#elif defined(__ADSPBF54x__)
-# define DO_MUX(port, tx, rx) \
- bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##tx##_MASK | PORT_x_MUX_##rx##_MASK)) | PORT_x_MUX_##tx##_FUNC_1 | PORT_x_MUX_##rx##_FUNC_1); \
- bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx);
- switch (CONFIG_UART_CONSOLE) {
- case 0: DO_MUX(E, 7, 8); break; /* Port E; PE7 and PE8 */
- case 1: DO_MUX(H, 0, 1); break; /* Port H; PH0 and PH1 */
- case 2: DO_MUX(B, 4, 5); break; /* Port B; PB4 and PB5 */
- case 3: DO_MUX(B, 6, 7); break; /* Port B; PB6 and PB7 */
- }
- SSYNC();
-#elif defined(__ADSPBF561__)
- /* UART pins could be GPIO, but they aren't pin muxed. */
-#else
-# if (P_UART(RX) & P_DEFINED) || (P_UART(TX) & P_DEFINED)
-# error "missing portmux logic for UART"
-# endif
-#endif
-}
-
-__attribute__((always_inline))
-static inline int uart_init(uint32_t uart_base)
-{
- /* always enable UART -- avoids anomalies 05000309 and 05000350 */
- bfin_write(&pUART->gctl, UCEN);
-
- /* Set LCR to Word Lengh 8-bit word select */
- bfin_write(&pUART->lcr, WLS_8);
-
- SSYNC();
-
- return 0;
-}
-
-__attribute__((always_inline))
-static inline int serial_early_init(uint32_t uart_base)
-{
- /* handle portmux crap on different Blackfins */
- serial_do_portmux();
-
- return uart_init(uart_base);
-}
-
-__attribute__((always_inline))
-static inline int serial_early_uninit(uint32_t uart_base)
-{
- /* disable the UART by clearing UCEN */
- bfin_write(&pUART->gctl, 0);
-
- return 0;
-}
-
-__attribute__((always_inline))
-static inline void serial_early_put_div(uint32_t uart_base, uint16_t divisor)
-{
- /* Set DLAB in LCR to Access DLL and DLH */
- ACCESS_LATCH();
- SSYNC();
-
- /* Program the divisor to get the baud rate we want */
- bfin_write(&pUART->dll, LOB(divisor));
- bfin_write(&pUART->dlh, HIB(divisor));
- SSYNC();
-
- /* Clear DLAB in LCR to Access THR RBR IER */
- ACCESS_PORT_IER();
- SSYNC();
-}
-
-__attribute__((always_inline))
-static inline uint16_t serial_early_get_div(void)
-{
- uint32_t uart_base = UART_DLL;
-
- /* Set DLAB in LCR to Access DLL and DLH */
- ACCESS_LATCH();
- SSYNC();
-
- uint8_t dll = bfin_read(&pUART->dll);
- uint8_t dlh = bfin_read(&pUART->dlh);
- uint16_t divisor = (dlh << 8) | dll;
-
- /* Clear DLAB in LCR to Access THR RBR IER */
- ACCESS_PORT_IER();
- SSYNC();
-
- return divisor;
-}
-
-/* We cannot use get_sclk() early on as it uses caches in external memory */
-#if defined(BFIN_IN_INITCODE) || defined(CONFIG_DEBUG_EARLY_SERIAL)
-# define get_sclk() (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV)
-#endif
-
-__attribute__((always_inline))
-static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud)
-{
- /* Translate from baud into divisor in terms of SCLK. The
- * weird multiplication is to make sure we over sample just
- * a little rather than under sample the incoming signals.
- */
- serial_early_put_div(uart_base,
- (get_sclk() + (baud * 8)) / (baud * 16) - ANOMALY_05000230);
-}
-
-#ifndef BFIN_IN_INITCODE
-__attribute__((always_inline))
-static inline void serial_early_puts(const char *s)
-{
- if (BFIN_DEBUG_EARLY_SERIAL) {
- serial_puts("Early: ");
- serial_puts(s);
- }
-}
-#endif
-
-#else
-
-.macro serial_early_init
-#ifdef CONFIG_DEBUG_EARLY_SERIAL
- call _serial_initialize;
-#endif
-.endm
-
-.macro serial_early_set_baud
-#ifdef CONFIG_DEBUG_EARLY_SERIAL
- R0.L = LO(CONFIG_BAUDRATE);
- R0.H = HI(CONFIG_BAUDRATE);
- call _serial_set_baud;
-#endif
-.endm
-
-/* Since we embed the string right into our .text section, we need
- * to find its address. We do this by getting our PC and adding 2
- * bytes (which is the length of the jump instruction). Then we
- * pass this address to serial_puts().
- */
-#ifdef CONFIG_DEBUG_EARLY_SERIAL
-# define serial_early_puts(str) \
- .section .rodata; \
- 7: \
- .ascii "Early:"; \
- .ascii __FILE__; \
- .ascii ": "; \
- .ascii str; \
- .asciz "\n"; \
- .previous; \
- R0.L = 7b; \
- R0.H = 7b; \
- call _serial_puts;
-#else
-# define serial_early_puts(str)
-#endif
-
-#endif
-
-#endif
projects / karo-tx-uboot.git / blobdiff