* port_phy_addr).
*
* INPUT:
-* ETH_PORT_INFO *p_eth_port_ctrl Ethernet port control struct
+* ETH_PORT_INFO *p_eth_port_ctrl Ethernet port control struct
*
* OUTPUT:
* See description.
* ether_init_rx_desc_ring for Rx queues).
*
* INPUT:
-* ETH_PORT_INFO *p_eth_port_ctrl Ethernet port control struct
+* ETH_PORT_INFO *p_eth_port_ctrl Ethernet port control struct
*
* OUTPUT:
* Ethernet port is ready to receive and transmit.
* INPUT:
* ETH_PORT eth_port_num Port number.
* char * p_addr Address to be set
-* ETH_QUEUE queue Rx queue number for this MAC address.
+* ETH_QUEUE queue Rx queue number for this MAC address.
*
* OUTPUT:
* Set MAC address low and high registers. also calls eth_port_uc_addr()
* parameters.
*
* INPUT:
-* ETH_PORT eth_port_num Port number.
+* ETH_PORT eth_port_num Port number.
* unsigned char uc_nibble Unicast MAC Address last nibble.
-* ETH_QUEUE queue Rx queue number for this MAC address.
-* int option 0 = Add, 1 = remove address.
+* ETH_QUEUE queue Rx queue number for this MAC address.
+* int option 0 = Add, 1 = remove address.
*
* OUTPUT:
* This function add/removes MAC addresses from the port unicast address
* In this case, the function calculates the CRC-8bit value and calls
* eth_port_omc_addr() routine to set the Other Multicast Table.
* INPUT:
-* ETH_PORT eth_port_num Port number.
-* unsigned char *p_addr Unicast MAC Address.
-* ETH_QUEUE queue Rx queue number for this MAC address.
-* int option 0 = Add, 1 = remove address.
+* ETH_PORT eth_port_num Port number.
+* unsigned char *p_addr Unicast MAC Address.
+* ETH_QUEUE queue Rx queue number for this MAC address.
+* int option 0 = Add, 1 = remove address.
*
* OUTPUT:
* See description.
* according to the argument given.
*
* INPUT:
-* ETH_PORT eth_port_num Port number.
-* unsigned char mc_byte Multicast addr last byte (MAC DA[7:0] bits).
-* ETH_QUEUE queue Rx queue number for this MAC address.
-* int option 0 = Add, 1 = remove address.
+* ETH_PORT eth_port_num Port number.
+* unsigned char mc_byte Multicast addr last byte (MAC DA[7:0] bits).
+* ETH_QUEUE queue Rx queue number for this MAC address.
+* int option 0 = Add, 1 = remove address.
*
* OUTPUT:
* See description.
* CRC-8 argument given.
*
* INPUT:
-* ETH_PORT eth_port_num Port number.
-* unsigned char crc8 A CRC-8bit (Polynomial: x^8+x^2+x^1+1).
-* ETH_QUEUE queue Rx queue number for this MAC address.
-* int option 0 = Add, 1 = remove address.
+* ETH_PORT eth_port_num Port number.
+* unsigned char crc8 A CRC-8bit (Polynomial: x^8+x^2+x^1+1).
+* ETH_QUEUE queue Rx queue number for this MAC address.
+* int option 0 = Add, 1 = remove address.
*
* OUTPUT:
* See description.
* eth_port_reset - Reset Ethernet port
*
* DESCRIPTION:
- * This routine resets the chip by aborting any SDMA engine activity and
+ * This routine resets the chip by aborting any SDMA engine activity and
* clearing the MIB counters. The Receiver and the Transmit unit are in
* idle state after this command is performed and the port is disabled.
*
*
* INPUT:
* ETH_PORT_INFO *p_eth_port_ctrl Ethernet Port Control srtuct.
- * ETH_QUEUE rx_queue Number of Rx queue.
- * int rx_desc_num Number of Rx descriptors
- * int rx_buff_size Size of Rx buffer
+ * ETH_QUEUE rx_queue Number of Rx queue.
+ * int rx_desc_num Number of Rx descriptors
+ * int rx_buff_size Size of Rx buffer
* unsigned int rx_desc_base_addr Rx descriptors memory area base addr.
* unsigned int rx_buff_base_addr Rx buffer memory area base addr.
*
*
* INPUT:
* ETH_PORT_INFO *p_eth_port_ctrl Ethernet Port Control srtuct.
- * ETH_QUEUE tx_queue Number of Tx queue.
- * int tx_desc_num Number of Tx descriptors
- * int tx_buff_size Size of Tx buffer
+ * ETH_QUEUE tx_queue Number of Tx queue.
+ * int tx_desc_num Number of Tx descriptors
+ * int tx_buff_size Size of Tx buffer
* unsigned int tx_desc_base_addr Tx descriptors memory area base addr.
* unsigned int tx_buff_base_addr Tx buffer memory area base addr.
*
*
* INPUT:
* ETH_PORT_INFO *p_eth_port_ctrl Ethernet Port Control srtuct.
- * ETH_QUEUE tx_queue Number of Tx queue.
+ * ETH_QUEUE tx_queue Number of Tx queue.
* PKT_INFO *p_pkt_info User packet buffer.
*
* OUTPUT:
*
* INPUT:
* ETH_PORT_INFO *p_eth_port_ctrl Ethernet Port Control srtuct.
- * ETH_QUEUE tx_queue Number of Tx queue.
+ * ETH_QUEUE tx_queue Number of Tx queue.
* PKT_INFO *p_pkt_info User packet buffer.
*
* OUTPUT:
* eth_port_receive - Get received information from Rx ring.
*
* DESCRIPTION:
- * This routine returns the received data to the caller. There is no
+ * This routine returns the received data to the caller. There is no
* data copying during routine operation. All information is returned
* using pointer to packet information struct passed from the caller.
* If the routine exhausts Rx ring resources then the resource error flag
*
* INPUT:
* ETH_PORT_INFO *p_eth_port_ctrl Ethernet Port Control srtuct.
- * ETH_QUEUE rx_queue Number of Rx queue.
+ * ETH_QUEUE rx_queue Number of Rx queue.
* PKT_INFO *p_pkt_info User packet buffer.
*
* OUTPUT:
/* Nothing to receive... */
if (command_status & (ETH_BUFFER_OWNED_BY_DMA)) {
-/* DP(printf("Rx: command_status: %08x\n", command_status)); */
+/* DP(printf("Rx: command_status: %08x\n", command_status)); */
D_CACHE_FLUSH_LINE ((unsigned int) p_rx_curr_desc, 0);
/* DP(printf("\nETH_END_OF_JOB ...\n"));*/
return ETH_END_OF_JOB;
*
* INPUT:
* ETH_PORT_INFO *p_eth_port_ctrl Ethernet Port Control srtuct.
- * ETH_QUEUE rx_queue Number of Rx queue.
+ * ETH_QUEUE rx_queue Number of Rx queue.
* PKT_INFO *p_pkt_info Information on the returned buffer.
*
* OUTPUT:
projects / karo-tx-uboot.git / blobdiff