#include <version.h>
#include <asm/arch/pxa-regs.h>
-DRAM_SIZE: .long CFG_DRAM_SIZE
+DRAM_SIZE: .long CONFIG_SYS_DRAM_SIZE
/* wait for coprocessor write complete */
.macro CPWAIT reg
/*
- * Memory setup
+ * Memory setup
*/
.globl lowlevel_init
/* Set up GPIO pins first ----------------------------------------- */
ldr r0, =GPSR0
- ldr r1, =CFG_GPSR0_VAL
+ ldr r1, =CONFIG_SYS_GPSR0_VAL
str r1, [r0]
ldr r0, =GPSR1
- ldr r1, =CFG_GPSR1_VAL
+ ldr r1, =CONFIG_SYS_GPSR1_VAL
str r1, [r0]
ldr r0, =GPSR2
- ldr r1, =CFG_GPSR2_VAL
+ ldr r1, =CONFIG_SYS_GPSR2_VAL
str r1, [r0]
ldr r0, =GPCR0
- ldr r1, =CFG_GPCR0_VAL
+ ldr r1, =CONFIG_SYS_GPCR0_VAL
str r1, [r0]
ldr r0, =GPCR1
- ldr r1, =CFG_GPCR1_VAL
+ ldr r1, =CONFIG_SYS_GPCR1_VAL
str r1, [r0]
ldr r0, =GPCR2
- ldr r1, =CFG_GPCR2_VAL
+ ldr r1, =CONFIG_SYS_GPCR2_VAL
str r1, [r0]
ldr r0, =GPDR0
- ldr r1, =CFG_GPDR0_VAL
+ ldr r1, =CONFIG_SYS_GPDR0_VAL
str r1, [r0]
ldr r0, =GPDR1
- ldr r1, =CFG_GPDR1_VAL
+ ldr r1, =CONFIG_SYS_GPDR1_VAL
str r1, [r0]
ldr r0, =GPDR2
- ldr r1, =CFG_GPDR2_VAL
+ ldr r1, =CONFIG_SYS_GPDR2_VAL
str r1, [r0]
ldr r0, =GAFR0_L
- ldr r1, =CFG_GAFR0_L_VAL
+ ldr r1, =CONFIG_SYS_GAFR0_L_VAL
str r1, [r0]
ldr r0, =GAFR0_U
- ldr r1, =CFG_GAFR0_U_VAL
+ ldr r1, =CONFIG_SYS_GAFR0_U_VAL
str r1, [r0]
ldr r0, =GAFR1_L
- ldr r1, =CFG_GAFR1_L_VAL
+ ldr r1, =CONFIG_SYS_GAFR1_L_VAL
str r1, [r0]
ldr r0, =GAFR1_U
- ldr r1, =CFG_GAFR1_U_VAL
+ ldr r1, =CONFIG_SYS_GAFR1_U_VAL
str r1, [r0]
ldr r0, =GAFR2_L
- ldr r1, =CFG_GAFR2_L_VAL
+ ldr r1, =CONFIG_SYS_GAFR2_L_VAL
str r1, [r0]
ldr r0, =GAFR2_U
- ldr r1, =CFG_GAFR2_U_VAL
+ ldr r1, =CONFIG_SYS_GAFR2_U_VAL
str r1, [r0]
ldr r0, =PSSR /* enable GPIO pins */
- ldr r1, =CFG_PSSR_VAL
+ ldr r1, =CONFIG_SYS_PSSR_VAL
str r1, [r0]
/* ldr r3, =MSC1 / low - bank 2 Lubbock Registers / SRAM */
-/* ldr r2, =CFG_MSC1_VAL / high - bank 3 Ethernet Controller */
+/* ldr r2, =CONFIG_SYS_MSC1_VAL / high - bank 3 Ethernet Controller */
/* str r2, [r3] / need to set MSC1 before trying to write to the HEX LEDs */
/* ldr r2, [r3] / need to read it back to make sure the value latches (see MSC section of manual) */
/* */
/*loop: */
/* */
/* ldr r0, =0xB0070001 */
-/* ldr r1, =_LED */
-/* str r0, [r1] / hex display */
+/* ldr r1, =_LED */
+/* str r0, [r1] / hex display */
/* ---------------------------------------------------------------- */
/* MSC registers: timing, bus width, mem type */
/* MSC0: nCS(0,1) */
- ldr r2, =CFG_MSC0_VAL
+ ldr r2, =CONFIG_SYS_MSC0_VAL
str r2, [r1, #MSC0_OFFSET]
ldr r2, [r1, #MSC0_OFFSET] /* read back to ensure */
/* that data latches */
/* MSC1: nCS(2,3) */
- ldr r2, =CFG_MSC1_VAL
+ ldr r2, =CONFIG_SYS_MSC1_VAL
str r2, [r1, #MSC1_OFFSET]
ldr r2, [r1, #MSC1_OFFSET]
/* MSC2: nCS(4,5) */
- ldr r2, =CFG_MSC2_VAL
+ ldr r2, =CONFIG_SYS_MSC2_VAL
str r2, [r1, #MSC2_OFFSET]
ldr r2, [r1, #MSC2_OFFSET]
/* ---------------------------------------------------------------- */
/* MECR: Memory Expansion Card Register */
- ldr r2, =CFG_MECR_VAL
+ ldr r2, =CONFIG_SYS_MECR_VAL
str r2, [r1, #MECR_OFFSET]
ldr r2, [r1, #MECR_OFFSET]
/* MCMEM0: Card Interface slot 0 timing */
- ldr r2, =CFG_MCMEM0_VAL
+ ldr r2, =CONFIG_SYS_MCMEM0_VAL
str r2, [r1, #MCMEM0_OFFSET]
ldr r2, [r1, #MCMEM0_OFFSET]
/* MCMEM1: Card Interface slot 1 timing */
- ldr r2, =CFG_MCMEM1_VAL
+ ldr r2, =CONFIG_SYS_MCMEM1_VAL
str r2, [r1, #MCMEM1_OFFSET]
ldr r2, [r1, #MCMEM1_OFFSET]
/* MCATT0: Card Interface Attribute Space Timing, slot 0 */
- ldr r2, =CFG_MCATT0_VAL
+ ldr r2, =CONFIG_SYS_MCATT0_VAL
str r2, [r1, #MCATT0_OFFSET]
ldr r2, [r1, #MCATT0_OFFSET]
/* MCATT1: Card Interface Attribute Space Timing, slot 1 */
- ldr r2, =CFG_MCATT1_VAL
+ ldr r2, =CONFIG_SYS_MCATT1_VAL
str r2, [r1, #MCATT1_OFFSET]
ldr r2, [r1, #MCATT1_OFFSET]
/* MCIO0: Card Interface I/O Space Timing, slot 0 */
- ldr r2, =CFG_MCIO0_VAL
+ ldr r2, =CONFIG_SYS_MCIO0_VAL
str r2, [r1, #MCIO0_OFFSET]
ldr r2, [r1, #MCIO0_OFFSET]
/* MCIO1: Card Interface I/O Space Timing, slot 1 */
- ldr r2, =CFG_MCIO1_VAL
+ ldr r2, =CONFIG_SYS_MCIO1_VAL
str r2, [r1, #MCIO1_OFFSET]
ldr r2, [r1, #MCIO1_OFFSET]
/* Before accessing MDREFR we need a valid DRI field, so we set */
/* this to power on defaults + DRI field. */
- ldr r3, =CFG_MDREFR_VAL
+ ldr r3, =CONFIG_SYS_MDREFR_VAL
ldr r2, =0xFFF
and r3, r3, r2
ldr r4, =0x03ca4000
/* Step 4a: assert MDREFR:K?RUN and configure */
/* MDREFR:K1DB2 and MDREFR:K2DB2 as desired. */
- ldr r4, =CFG_MDREFR_VAL
+ ldr r4, =CONFIG_SYS_MDREFR_VAL
str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */
ldr r4, [r1, #MDREFR_OFFSET]
/* Step 4d: write MDCNFG with MDCNFG:DEx deasserted (set to 0), to */
/* configure but not enable each SDRAM partition pair. */
- ldr r4, =CFG_MDCNFG_VAL
+ ldr r4, =CONFIG_SYS_MDCNFG_VAL
bic r4, r4, #(MDCNFG_DE0|MDCNFG_DE1)
str r4, [r1, #MDCNFG_OFFSET] /* write back MDCNFG */
/* Jan 2003, Errata #116, page 30. */
- ldr r3, =CFG_DRAM_BASE
+ ldr r3, =CONFIG_SYS_DRAM_BASE
str r2, [r3]
str r2, [r3]
str r2, [r3]
/* Step 4h: Write MDMRS. */
- ldr r2, =CFG_MDMRS_VAL
+ ldr r2, =CONFIG_SYS_MDMRS_VAL
str r2, [r1, #MDMRS_OFFSET]
projects / karo-tx-uboot.git / blobdiff