#include <malloc.h>
#include <pci.h>
#include <asm/4xx_pci.h>
+#include <asm/io.h>
#include "pci405.h"
DECLARE_GLOBAL_DATA_PTR;
/* Prototypes */
-int gunzip(void *, int, unsigned char *, unsigned long *);
-int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);/*cmd_boot.c*/
unsigned long fpga_done_state(void);
unsigned long fpga_init_state(void);
*/
#include "../common/fpga.c"
-#define FPGA_DONE_STATE_V11 (in32(GPIO0_IR) & CFG_FPGA_DONE)
-#define FPGA_DONE_STATE_V12 (in32(GPIO0_IR) & CFG_FPGA_DONE_V12)
+#define FPGA_DONE_STATE_V11 (in_be32((void*)GPIO0_IR) & CONFIG_SYS_FPGA_DONE)
+#define FPGA_DONE_STATE_V12 (in_be32((void*)GPIO0_IR) & CONFIG_SYS_FPGA_DONE_V12)
-#define FPGA_INIT_STATE_V11 (in32(GPIO0_IR) & CFG_FPGA_INIT)
-#define FPGA_INIT_STATE_V12 (in32(GPIO0_IR) & CFG_FPGA_INIT_V12)
+#define FPGA_INIT_STATE_V11 (in_be32((void*)GPIO0_IR) & CONFIG_SYS_FPGA_INIT)
+#define FPGA_INIT_STATE_V12 (in_be32((void*)GPIO0_IR) & CONFIG_SYS_FPGA_INIT_V12)
int board_revision(void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
/*
* Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x03000000);
- out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x00100200);
- out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x00100200);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
+ out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00100200);
+ out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00100200);
udelay(1000); /* wait some time before reading input */
- value = in32(GPIO0_IR) & 0x00100200; /* get config bits */
+ value = in_be32((void*)GPIO0_IR) & 0x00100200; /* get config bits */
/*
* Restore GPIO settings
*/
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
switch (value) {
case 0x00100200:
int board_early_init_f (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/*
* First pull fpga-prg pin low, to disable fpga logic (on version 1.2 board)
*/
- out32(GPIO0_ODR, 0x00000000); /* no open drain pins */
- out32(GPIO0_TCR, CFG_FPGA_PRG); /* setup for output */
- out32(GPIO0_OR, CFG_FPGA_PRG); /* set output pins to high */
- out32(GPIO0_OR, 0); /* pull prg low */
+ out_be32((void*)GPIO0_ODR, 0x00000000); /* no open drain pins */
+ out_be32((void*)GPIO0_TCR, CONFIG_SYS_FPGA_PRG); /* setup for output */
+ out_be32((void*)GPIO0_OR, CONFIG_SYS_FPGA_PRG); /* set output pins to high */
+ out_be32((void*)GPIO0_OR, 0); /* pull prg low */
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
* IRQ 30 (EXT IRQ 5) FPGA Timestamp; active low; level sensitive
* IRQ 31 (EXT IRQ 6) PCI Reset; active low; level sensitive
*/
- mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr(uicer, 0x00000000); /* disable all ints */
- mtdcr(uiccr, 0x00000000); /* set all to be non-critical*/
- mtdcr(uicpr, 0xFFFFFF80); /* set int polarities */
- mtdcr(uictr, 0x10000000); /* set int trigger levels */
- mtdcr(uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority*/
- mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0ER, 0x00000000); /* disable all ints */
+ mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
+ mtdcr(UIC0PR, 0xFFFFFF80); /* set int polarities */
+ mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
+ mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
/*
* Setup GPIO pins (IRQ4/GPIO21 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00008000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00008000);
/*
* Setup GPIO pins (CS6+CS7 as GPIO)
*/
- mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 25 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
-
-/* ------------------------------------------------------------------------- */
-
-int misc_init_f (void)
-{
- return 0; /* dummy implementation */
-}
-
-
int misc_init_r (void)
{
unsigned char *dst;
* FPGA can be gzip compressed (malloc) and booted this late.
*/
- dst = malloc(CFG_FPGA_MAX_SIZE);
- if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
+ dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
+ if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
printf ("GUNZIP ERROR - must RESET board to recover\n");
do_reset (NULL, 0, 0, NULL);
}
pci_write_config_dword(PCIDEVID_405GP, i, *ptr++);
}
}
- mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
+ mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
*magic = 0; /* clear pci reconfig magic again */
}
-#if 1 /* test-only */
/*
* Decrease PLB latency timeout and reduce priority of the PCI bridge master
*/
#define PCI0_BRDGOPT1 0x4a
pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f20);
-/* pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f60); */
-#define plb0_acr 0x87
/*
* Enable fairness and high bus utilization
*/
- mtdcr(plb0_acr, 0x98000000);
-
-#if 0 /* test-only */
- printf("CCR0=%08x\n", mfspr(ccr0)); /* test-only */
-/* mtspr(ccr0, (mfspr(ccr0) & 0xff8fffff) | 0x00100000); */
- mtspr(ccr0, (mfspr(ccr0) & 0xff8fffff) | 0x00000000);
-#endif
-/* printf("CCR0=%08x\n", mfspr(ccr0)); */ /* test-only */
-#endif
+ mtdcr(PLB0_ACR, 0x98000000);
free(dst);
return (0);
/*
* Check Board Identity:
*/
-
int checkboard (void)
{
char str[64];
- int i = getenv_r ("serial#", str, sizeof(str));
+ int i = getenv_f("serial#", str, sizeof(str));
puts ("Board: ");
printf(" (Rev 1.%ld", gd->board_type);
if (gd->board_type >= 2) {
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
* Setup GPIO pins (Trace/GPIO1 to GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg & ~0x08000000);
- out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x40000000);
- out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x40000000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg & ~0x08000000);
+ out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x40000000);
+ out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x40000000);
udelay(1000); /* wait some time before reading input */
- value = in32(GPIO0_IR) & 0x40000000; /* get config bits */
+ value = in_be32((void*)GPIO0_IR) & 0x40000000; /* get config bits */
if (value) {
puts(", 33 MHz PCI");
} else {
- puts(", 66 Mhz PCI");
+ puts(", 66 MHz PCI");
}
}
}
/* ------------------------------------------------------------------------- */
+#define UART1_MCR 0xef600404
int wpeeprom(int wp)
{
int wp_state = wp;
- volatile unsigned char *uart1_mcr = (volatile unsigned char *)0xef600404;
if (wp == 1) {
- *uart1_mcr &= ~0x02;
+ out_8((void *)UART1_MCR, in_8((void *)UART1_MCR) & ~0x02);
} else if (wp == 0) {
- *uart1_mcr |= 0x02;
+ out_8((void *)UART1_MCR, in_8((void *)UART1_MCR) | 0x02);
} else {
- if (*uart1_mcr & 0x02) {
+ if (in_8((void *)UART1_MCR) & 0x02) {
wp_state = 0;
} else {
wp_state = 1;
return wp_state;
}
-int do_wpeeprom(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int do_wpeeprom(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int wp = -1;
if (argc >= 2) {
U_BOOT_CMD(
wpeeprom, 2, 1, do_wpeeprom,
- "wpeeprom - Check/Enable/Disable I2C EEPROM write protection\n",
+ "Check/Enable/Disable I2C EEPROM write protection",
"wpeeprom\n"
" - check I2C EEPROM write protection state\n"
"wpeeprom 1\n"
" - enable I2C EEPROM write protection\n"
"wpeeprom 0\n"
- " - disable I2C EEPROM write protection\n"
- );
+ " - disable I2C EEPROM write protection"
+);
projects / karo-tx-uboot.git / blobdiff