#include <common.h>
#include "mip405.h"
#include <asm/processor.h>
-#include <405gp_i2c.h>
+#include <4xx_i2c.h>
#include <miiphy.h>
#include "../common/common_util.h"
+#include <stdio_dev.h>
#include <i2c.h>
#include <rtc.h>
-extern block_dev_desc_t * scsi_get_dev(int dev);
-extern block_dev_desc_t * ide_get_dev(int dev);
+
+DECLARE_GLOBAL_DATA_PTR;
#undef SDRAM_DEBUG
#define ENABLE_ECC /* for ecc boards */
#endif
-#define PLD_PART_REG PER_PLD_ADDR + 0
-#define PLD_VERS_REG PER_PLD_ADDR + 1
-#define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2
-#define PLD_IRQ_REG PER_PLD_ADDR + 3
-#define PLD_COM_MODE_REG PER_PLD_ADDR + 4
-#define PLD_EXT_CONF_REG PER_PLD_ADDR + 5
+#define PLD_PART_REG PER_PLD_ADDR + 0
+#define PLD_VERS_REG PER_PLD_ADDR + 1
+#define PLD_BOARD_CFG_REG PER_PLD_ADDR + 2
+#define PLD_IRQ_REG PER_PLD_ADDR + 3
+#define PLD_COM_MODE_REG PER_PLD_ADDR + 4
+#define PLD_EXT_CONF_REG PER_PLD_ADDR + 5
#define MEGA_BYTE (1024*1024)
void SDRAM_err (const char *s)
{
#ifndef SDRAM_DEBUG
- DECLARE_GLOBAL_DATA_PTR;
-
(void) get_clocks ();
gd->baudrate = 9600;
serial_init ();
int init_sdram (void)
{
- DECLARE_GLOBAL_DATA_PTR;
-
unsigned long tmp, baseaddr;
unsigned short i;
unsigned char trp_clocks,
unsigned char bc;
unsigned long sdram_tim, sdram_bank;
- /*i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);*/
+ /*i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);*/
(void) get_clocks ();
gd->baudrate = 9600;
serial_init ();
serial_puts ("\n");
#endif
i = 0;
- baseaddr = CFG_SDRAM_BASE;
+ baseaddr = CONFIG_SYS_SDRAM_BASE;
while (sdram_table[i].sz != 0xff) {
if (sdram_table[i].boardtype == bc)
break;
int checkboard (void)
{
- unsigned char s[50];
+ char s[50];
unsigned char bc, var;
int i;
backup_t *b = (backup_t *) s;
puts ("Board: ");
get_pcbrev_var(&bc,&var);
- i = getenv_r ("serial#", s, 32);
- if ((i == 0) || strncmp (s, BOARD_NAME,sizeof(BOARD_NAME))) {
+ i = getenv_r ("serial#", (char *)s, 32);
+ if ((i == 0) || strncmp ((char *)s, BOARD_NAME,sizeof(BOARD_NAME))) {
get_backup_values (b);
if (strncmp (b->signature, "MPL\0", 4) != 0) {
puts ("### No HW ID - assuming " BOARD_NAME);
/* ------------------------------------------------------------------------- */
static int test_dram (unsigned long ramsize);
-long int initdram (int board_type)
+phys_size_t initdram (int board_type)
{
unsigned long bank_reg[4], tmp, bank_size;
int misc_init_r (void)
{
- DECLARE_GLOBAL_DATA_PTR;
/* adjust flash start and size as well as the offset */
gd->bd->bi_flashstart=0-flash_info[0].size;
- gd->bd->bi_flashsize=flash_info[0].size-CFG_MONITOR_LEN;
+ gd->bd->bi_flashsize=flash_info[0].size-CONFIG_SYS_MONITOR_LEN;
gd->bd->bi_flashoffset=0;
/* check, if RTC is running */
start=get_timer(0);
/* if MIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
if (mfdcr(strap) & PSR_ROM_LOC)
- mtspr(ccr0, (mfspr(ccr0) & ~0x80));
+ mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
return (0);
}
{
unsigned long stop;
struct rtc_time newtm;
- unsigned char *s;
+ char *s;
mem_test_reloc();
/* write correct LED configuration */
- if (miiphy_write (0x1, 0x14, 0x2402) != 0) {
+ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x14, 0x2402) != 0) {
printf ("Error writing to the PHY\n");
}
/* since LED/CFG2 is not connected on the -2,
* write to correct capability information */
- if (miiphy_write (0x1, 0x4, 0x01E1) != 0) {
+ if (miiphy_write("ppc_4xx_eth0", 0x1, 0x4, 0x01E1) != 0) {
printf ("Error writing to the PHY\n");
}
print_mip405_rev ();
- show_stdio_dev ();
+ stdio_print_current_devices ();
check_env ();
/* check if RTC time is valid */
stop=get_timer(start);