#include <common.h>
#include <asm/io.h>
#include <asm/errno.h>
+#include <asm/arch/hardware.h>
#include <asm/arch/mem.h>
#include <linux/mtd/omap_gpmc.h>
#include <linux/mtd/nand_ecc.h>
#define PRINT_REG(x) debug("+++ %.15s (0x%08x)=0x%08x\n", #x, &gpmc_cfg->x, readl(&gpmc_cfg->x))
-#ifdef CONFIG_SYS_GPMC_PREFETCH_ENABLE
-/**
- * gpmc_prefetch_enable - configures and starts prefetch transfer
- * @cs: cs (chip select) number
- * @fifo_th: fifo threshold to be used for read/ write
- * @count: number of bytes to be transferred
- * @is_write: prefetch read(0) or write post(1) mode
- */
-static inline void gpmc_prefetch_enable(int cs, int fifo_th,
- unsigned int count, int is_write)
-{
- writel(count, &gpmc_cfg->pref_config2);
-
- /* Set the prefetch read / post write and enable the engine.
- * Set which cs is has requested for.
- */
- uint32_t val = (cs << CS_NUM_SHIFT) |
- PREFETCH_ENABLEOPTIMIZEDACCESS |
- PREFETCH_FIFOTHRESHOLD(fifo_th) |
- ENABLE_PREFETCH |
- !!is_write;
- writel(val, &gpmc_cfg->pref_config1);
-
- /* Start the prefetch engine */
- writel(0x1, &gpmc_cfg->pref_control);
-}
-
-/**
- * gpmc_prefetch_reset - disables and stops the prefetch engine
- */
-static inline void gpmc_prefetch_reset(void)
-{
- /* Stop the PFPW engine */
- writel(0x0, &gpmc_cfg->pref_control);
-
- /* Reset/disable the PFPW engine */
- writel(0x0, &gpmc_cfg->pref_config1);
-}
-
-//#define FIFO_IOADDR (nand->IO_ADDR_R)
-#define FIFO_IOADDR PISMO1_NAND_BASE
-
-/**
- * read_buf_pref - read data from NAND controller into buffer
- * @mtd: MTD device structure
- * @buf: buffer to store date
- * @len: number of bytes to read
- */
-static void read_buf_pref(struct mtd_info *mtd, u_char *buf, int len)
-{
- gpmc_prefetch_enable(cs, PREFETCH_FIFOTHRESHOLD_MAX, len, 0);
- do {
- // Get number of bytes waiting in the FIFO
- uint32_t read_bytes = GPMC_PREFETCH_STATUS_FIFO_CNT(readl(&gpmc_cfg->pref_status));
-
- if (read_bytes == 0)
- continue;
- // Alignment of Destination Buffer
- while (read_bytes && ((unsigned int)buf & 3)) {
- *buf++ = readb(FIFO_IOADDR);
- read_bytes--;
- len--;
- }
- // Use maximum word size (32bit) inside this loop, because speed is limited by
- // GPMC bus arbitration with a maximum transfer rate of 3.000.000/sec.
- len -= read_bytes & ~3;
- while (read_bytes >= 4) {
- *((uint32_t*)buf) = readl(FIFO_IOADDR);
- buf += 4;
- read_bytes -= 4;
- }
- // Transfer the last (non-aligned) bytes only at the last iteration,
- // to maintain full speed up to the end of the transfer.
- if (read_bytes == len) {
- while (read_bytes) {
- *buf++ = readb(FIFO_IOADDR);
- read_bytes--;
- }
- len = 0;
- }
- } while (len > 0);
- gpmc_prefetch_reset();
-}
-
-/*
- * write_buf_pref - write buffer to NAND controller
- * @mtd: MTD device structure
- * @buf: data buffer
- * @len: number of bytes to write
- */
-static void write_buf_pref(struct mtd_info *mtd, const u_char *buf, int len)
-{
- /* configure and start prefetch transfer */
- gpmc_prefetch_enable(cs, PREFETCH_FIFOTHRESHOLD_MAX, len, 1);
-
- while (len) {
- // Get number of free bytes in the FIFO
- uint32_t write_bytes = GPMC_PREFETCH_STATUS_FIFO_CNT(readl(&gpmc_cfg->pref_status));
-
- // don't write more bytes than requested
- if (write_bytes > len)
- write_bytes = len;
-
- // Alignment of Source Buffer
- while (write_bytes && ((unsigned int)buf & 3)) {
- writeb(*buf++, FIFO_IOADDR);
- write_bytes--;
- len--;
- }
-
- // Use maximum word size (32bit) inside this loop, because speed is limited by
- // GPMC bus arbitration with a maximum transfer rate of 3.000.000/sec.
- len -= write_bytes & ~3;
- while (write_bytes >= 4) {
- writel(*((uint32_t*)buf), FIFO_IOADDR);
- buf += 4;
- write_bytes -= 4;
- }
-
- // Transfer the last (non-aligned) bytes only at the last iteration,
- // to maintain full speed up to the end of the transfer.
- if (write_bytes == len) {
- while (write_bytes) {
- writeb(*buf++, FIFO_IOADDR);
- write_bytes--;
- }
- len = 0;
- }
- }
-
- /* wait for data to be flushed out before resetting the prefetch */
- while ((len = GPMC_PREFETCH_STATUS_COUNT(readl(&gpmc_cfg->pref_status)))) {
- debug("%u bytes still in FIFO\n", PREFETCH_FIFOTHRESHOLD_MAX - len);
- ndelay(1);
- }
-
- /* disable and stop the PFPW engine */
- gpmc_prefetch_reset();
-}
-#endif /* CONFIG_SYS_GPMC_PREFETCH_ENABLE */
-
/*
* omap_nand_hwcontrol - Set the address pointers corretly for the
* following address/data/command operation
/* Check wait pin as dev ready indicator */
static int omap_dev_ready(struct mtd_info *mtd)
{
+ struct nand_chip *this = mtd->priv;
+ struct omap_nand_info *info = this->priv;
return !!(readl(&gpmc_cfg->status) & (1 << (8 + info->ws)));
}
projects / karo-tx-uboot.git / blobdiff