/*
- * (C) Copyright 2005-2006
+ * (C) Copyright 2005-2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
*----------------------------------------------------------------------*/
#define CONFIG_BAMBOO 1 /* Board is BAMBOO */
#define CONFIG_440EP 1 /* Specific PPC440EP support */
+#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME bamboo
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/*
* 2nd ethernet port you have to "undef" the following define.
*/
#define CONFIG_BAMBOO_NAND 1 /* enable nand flash support */
-#define CFG_NAND_LEGACY
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
-#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
+#define CONFIG_SYS_FLASH_BASE 0xfff00000 /* start of FLASH */
+#define CONFIG_SYS_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
/*Don't change either of these*/
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/
-#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/
+#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* internal PCI regs*/
/*Don't change either of these*/
-#define CFG_USB_DEVICE 0x50000000
-#define CFG_NVRAM_BASE_ADDR 0x80000000
-#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_NAND_ADDR 0x90000000
-#define CFG_NAND2_ADDR 0x94000000
+#define CONFIG_SYS_USB_DEVICE 0x50000000
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0x80000000
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
+#define CONFIG_SYS_NAND_ADDR 0x90000000
+#define CONFIG_SYS_NAND2_ADDR 0x94000000
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in SDRAM)
*----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
-#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */
+#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */
+#define CONFIG_SYS_INIT_RAM_END (4 << 10)
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
+#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* NVRAM/RTC
*
* The DS1558 code assumes this condition
*
*----------------------------------------------------------------------*/
-#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
+#define CONFIG_SYS_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-/*
- * Define here the location of the environment variables (FLASH or EEPROM).
- * Note: DENX encourages to use redundant environment in FLASH.
- */
-#if 1
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
-#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_ADDR0 0x555
-#define CFG_FLASH_ADDR1 0x2aa
-#define CFG_FLASH_WORD_SIZE unsigned char
+#define CONFIG_SYS_FLASH_ADDR0 0x555
+#define CONFIG_SYS_FLASH_ADDR1 0x2aa
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char
-#define CFG_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */
-#define CFG_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */
+#define CONFIG_SYS_FLASH_2ND_16BIT_DEV 1 /* bamboo has 8 and 16bit device */
+#define CONFIG_SYS_FLASH_2ND_ADDR 0x87800000 /* bamboo has 8 and 16bit device */
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller. sr - 2006-08-25
+ */
+#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CONFIG_SYS_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#define CONFIG_SYS_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */
+
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 16
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CONFIG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#endif
/*-----------------------------------------------------------------------
- * NAND-FLASH related
+ * NAND FLASH
*----------------------------------------------------------------------*/
-#define NAND_CMD_REG (0x00) /* NandFlash Command Register */
-#define NAND_ADDR_REG (0x04) /* NandFlash Address Register */
-#define NAND_DATA_REG (0x08) /* NandFlash Data Register */
-#define NAND_ECC0_REG (0x10) /* NandFlash ECC Register0 */
-#define NAND_ECC1_REG (0x14) /* NandFlash ECC Register1 */
-#define NAND_ECC2_REG (0x18) /* NandFlash ECC Register2 */
-#define NAND_ECC3_REG (0x1C) /* NandFlash ECC Register3 */
-#define NAND_ECC4_REG (0x20) /* NandFlash ECC Register4 */
-#define NAND_ECC5_REG (0x24) /* NandFlash ECC Register5 */
-#define NAND_ECC6_REG (0x28) /* NandFlash ECC Register6 */
-#define NAND_ECC7_REG (0x2C) /* NandFlash ECC Register7 */
-#define NAND_CR0_REG (0x30) /* NandFlash Device Bank0 Config Register */
-#define NAND_CR1_REG (0x34) /* NandFlash Device Bank1 Config Register */
-#define NAND_CR2_REG (0x38) /* NandFlash Device Bank2 Config Register */
-#define NAND_CR3_REG (0x3C) /* NandFlash Device Bank3 Config Register */
-#define NAND_CCR_REG (0x40) /* NandFlash Core Configuration Register */
-#define NAND_STAT_REG (0x44) /* NandFlash Device Status Register */
-#define NAND_HWCTL_REG (0x48) /* NandFlash Direct Hwd Control Register */
-#define NAND_REVID_REG (0x50) /* NandFlash Core Revision Id Register */
-
-/* Nand Flash K9F1208U0A Command Set => Nand Flash 0 */
-#define NAND0_CMD_READ1_HALF1 0x00 /* Starting addr for 1rst half of registers */
-#define NAND0_CMD_READ1_HALF2 0x01 /* Starting addr for 2nd half of registers */
-#define NAND0_CMD_READ2 0x50
-#define NAND0_CMD_READ_ID 0x90
-#define NAND0_CMD_READ_STATUS 0x70
-#define NAND0_CMD_RESET 0xFF
-#define NAND0_CMD_PAGE_PROG 0x80
-#define NAND0_CMD_PAGE_PROG_TRUE 0x10
-#define NAND0_CMD_PAGE_PROG_DUMMY 0x11
-#define NAND0_CMD_BLOCK_ERASE 0x60
-#define NAND0_CMD_BLOCK_ERASE_END 0xD0
-
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_CMD_REG) = d;} while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_ADDR_REG) = d;} while(0)
-#define WRITE_NAND(d, adr) do {*(volatile u8 *)((ulong)adr+NAND_DATA_REG) = d;} while(0)
-#define READ_NAND(adr) (*(volatile u8 *)((ulong)adr+NAND_DATA_REG))
-#define NAND_WAIT_READY(nand) while (!(*(volatile u8 *)((ulong)nand->IO_ADDR+NAND_STAT_REG) & 0x01))
-
-/* not needed with 440EP NAND controller */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
+#define CONFIG_SYS_MAX_NAND_DEVICE 2
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_ADDR + 2 }
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_NAND_CS 1
+#else
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
+#endif
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------------- */
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#undef CONFIG_DDR_ECC /* don't use ECC */
-#define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */
-#define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51}
+#define CONFIG_SYS_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */
+#define SPD_EEPROM_ADDRESS {CONFIG_SYS_SIMULATE_SPD_EEPROM, 0x50, 0x51}
+#define CONFIG_SYS_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */
+#define CONFIG_PROG_SDRAM_TLB
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#ifdef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */
-#define CFG_ENV_OFFSET 0x0
-#endif /* CFG_ENV_IS_IN_EEPROM */
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */
+#define CONFIG_ENV_OFFSET 0x0
+#endif /* CONFIG_ENV_IS_IN_EEPROM */
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=bamboo\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/bamboo/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
- "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b 100000 fffa0000 60000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_HAS_ETH0
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#endif /* CONFIG_BAMBOO_NAND */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
#ifdef CONFIG_440EP
/* USB */
#define CONFIG_USB_OHCI
#define USB_2_0_DEVICE
#endif /*CONFIG_440EP*/
-#ifdef CONFIG_BAMBOO_NAND
-#define _CFG_CMD_NAND CFG_CMD_NAND
-#else
-#define _CFG_CMD_NAND 0
-#endif /* CONFIG_BAMBOO_NAND */
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_USB | \
- CFG_CMD_FAT | \
- CFG_CMD_EXT2 | \
- _CFG_CMD_NAND | \
- CFG_CMD_SNTP )
-
-#define CONFIG_SUPPORT_VFAT
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
/*
- * Miscellaneous configurable options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI 1 /* support kdi files */
+#ifdef CONFIG_BAMBOO_NAND
+#define CONFIG_CMD_NAND
+#endif
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SUPPORT_VFAT
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
/*-----------------------------------------------------------------------
* PCI stuff
#define CONFIG_PCI /* include pci support */
#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff