cm-t35: add support for loading splash image from NAND

[karo-tx-uboot.git] / include / configs / cm_t35.h

diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index fe91c10409b2cff78f51d9b6223e4c1114f80594..726714dd2118f8c193d8921406c385d3adf15d5d 100644 (file)
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -37,6 +37,7 @@
  */
 #define CONFIG_OMAP    /* in a TI OMAP core */
 #define CONFIG_OMAP34XX        /* which is a 34XX */
+#define CONFIG_OMAP_GPIO
 #define CONFIG_CM_T3X  /* working with CM-T35 and CM-T3730 */
 
 #define CONFIG_SYS_TEXT_BASE   0x80008000
@@ -56,7 +57,6 @@
 #define V_OSCK                 26000000        /* Clock output from T2 */
 #define V_SCLK                 (V_OSCK >> 1)
 
-#undef CONFIG_USE_IRQ                          /* no support for IRQs */
 #define CONFIG_MISC_INIT_R
 
 #define CONFIG_OF_LIBFDT               1
@@ -77,7 +77,7 @@
 /*
  * Size of malloc() pool
  */
-#define CONFIG_ENV_SIZE                (128 << 10)     /* 128 KiB */
+#define CONFIG_ENV_SIZE                (16 << 10)      /* 16 KiB */
                                        /* Sector */
 #define CONFIG_SYS_MALLOC_LEN  (CONFIG_ENV_SIZE + (128 << 10))
 
@@ -114,9 +114,15 @@
 #define CONFIG_DOS_PARTITION
 
 /* USB */
-#define CONFIG_MUSB_UDC
 #define CONFIG_USB_OMAP3
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_MUSB_UDC
 #define CONFIG_TWL4030_USB
+#define CONFIG_CMD_USB
 
 /* USB device configuration */
 #define CONFIG_USB_DEVICE
@@ -151,11 +157,10 @@
 #define CONFIG_HARD_I2C
 #define CONFIG_SYS_I2C_SPEED           100000
 #define CONFIG_SYS_I2C_SLAVE           1
-#define CONFIG_SYS_I2C_BUS             0
-#define CONFIG_SYS_I2C_BUS_SELECT      1
 #define CONFIG_DRIVER_OMAP34XX_I2C
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_I2C_MULTI_BUS
 
 /*
  * TWL4030
@@ -173,7 +178,7 @@
 #define CONFIG_SYS_NAND_BASE           NAND_BASE       /* physical address */
                                                        /* to access nand at */
                                                        /* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
+#define GPMC_NAND_ECC_LP_x8_LAYOUT
 
 #define CONFIG_SYS_MAX_NAND_DEVICE     1               /* Max number of NAND */
                                                        /* devices */
@@ -187,6 +192,7 @@
 
 /* Environment information */
 #define CONFIG_BOOTDELAY               10
+#define CONFIG_ZERO_BOOTDELAY_CHECK
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
        "loadaddr=0x82000000\0" \
@@ -230,7 +236,7 @@
                "bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-       "if mmc rescan ${mmcdev}; then " \
+       "mmc dev ${mmcdev}; if mmc rescan; then " \
                "if run loadbootscript; then " \
                        "run bootscript; " \
                "else " \
@@ -250,7 +256,6 @@
 #define CONFIG_SYS_AUTOLOAD            "no"
 #define CONFIG_SYS_LONGHELP            /* undef to save memory */
 #define CONFIG_SYS_HUSH_PARSER         /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #define CONFIG_SYS_PROMPT              "CM-T3x # "
 #define CONFIG_SYS_CBSIZE              256     /* Console I/O Buffer Size */
 /* Print Buffer Size */
@@ -277,45 +282,26 @@
 #define CONFIG_SYS_PTV                 2       /* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ                  1000
 
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE       (128 << 10)     /* regular stack 128 KiB */
-
 /*-----------------------------------------------------------------------
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS   1       /* CS1 is never populated */
 #define PHYS_SDRAM_1           OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE      (32 << 20)      /* at least 32 MiB */
 
 /*-----------------------------------------------------------------------
  * FLASH and environment organization
  */
 
 /* **** PISMO SUPPORT *** */
-
 /* Configure the PISMO */
 #define PISMO1_NAND_SIZE               GPMC_SIZE_128M
-#define PISMO1_ONEN_SIZE               GPMC_SIZE_128M
-
-#define CONFIG_SYS_MONITOR_LEN         (256 << 10)     /* Reserve 2 sectors */
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE          PISMO1_NAND_BASE
-#endif
 
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_ONENAND_BASE                ONENAND_MAP
+#define CONFIG_SYS_MONITOR_LEN         (256 << 10)     /* Reserve 2 sectors */
 
 #define CONFIG_ENV_IS_IN_NAND
-#define ONENAND_ENV_OFFSET             0x260000 /* environment starts here */
 #define SMNAND_ENV_OFFSET              0x260000 /* environment starts here */
-
-#define CONFIG_SYS_ENV_SECT_SIZE       (128 << 10)     /* 128 KiB */
 #define CONFIG_ENV_OFFSET              SMNAND_ENV_OFFSET
 #define CONFIG_ENV_ADDR                        SMNAND_ENV_OFFSET
 
@@ -345,9 +331,22 @@
 #define STATUS_LED_BOOT                        STATUS_LED_BIT
 #define GREEN_LED_GPIO                 186 /* CM-T35 Green LED is GPIO186 */
 
+#define CONFIG_SPLASHIMAGE_GUARD
+
 /* GPIO banks */
 #ifdef CONFIG_STATUS_LED
 #define CONFIG_OMAP3_GPIO_6    /* GPIO186 is in GPIO bank 6  */
 #endif
 
+/* Display Configuration */
+#define CONFIG_OMAP3_GPIO_2
+#define CONFIG_VIDEO_OMAP3
+#define LCD_BPP                LCD_COLOR16
+
+#define CONFIG_LCD
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_SPLASH_SCREEN_PREPARE
+
 #endif /* __CONFIG_H */