ARM: highbank: remove DRAM bank setup

[karo-tx-uboot.git] / include / configs / db-mv784mp-gp.h

diff --git a/include/configs/db-mv784mp-gp.h b/include/configs/db-mv784mp-gp.h
index 897f473f0c3d1ca42d2180b510f393de3cc03133..41e6fdcb526b01aea465c433490fa6e440e71f12 100644 (file)
--- a/include/configs/db-mv784mp-gp.h
+++ b/include/configs/db-mv784mp-gp.h
@@ -24,10 +24,10 @@
  * Commands configuration
  */
 #define CONFIG_SYS_NO_FLASH            /* Declare no flash (NOR/SPI) */
-#include <config_cmd_default.h>
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SF
 #define CONFIG_CMD_SPI
@@ -53,7 +53,7 @@
 #define CONFIG_ENV_SECT_SIZE           (64 << 10) /* 64KiB sectors */
 
 #define CONFIG_PHY_MARVELL             /* there is a marvell phy */
-#define CONFIG_PHY_BASE_ADDR   0x10
+#define CONFIG_PHY_ADDR                        { 0x10, 0x11, 0x12, 0x13 }
 #define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_QSGMII
 #define PHY_ANEG_TIMEOUT       8000    /* PHY needs a longer aneg time */
 #define CONFIG_RESET_PHY_R
@@ -61,6 +61,34 @@
 #define CONFIG_SYS_CONSOLE_INFO_QUIET  /* don't print console @ startup */
 #define CONFIG_SYS_ALT_MEMTEST
 
+/* SATA support */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE
+
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+
+#define CONFIG_SYS_ATA_REG_OFFSET      0x0100 /* Offset for register access */
+#define CONFIG_SYS_ATA_DATA_OFFSET     0x0100 /* Offset for data I/O */
+#define CONFIG_SYS_ATA_ALT_OFFSET      0x0100
+
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE          4
+
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS          2
+#define CONFIG_SYS_IDE_MAXDEVICE       CONFIG_SYS_IDE_MAXBUS
+
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR       MVEBU_AXP_SATA_BASE
+#define CONFIG_SYS_ATA_IDE0_OFFSET     0x2000
+#define CONFIG_SYS_ATA_IDE1_OFFSET     0x4000
+
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_CMD_IDE */
+
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
@@ -110,7 +138,7 @@
 #define CONFIG_SYS_SPI_U_BOOT_OFFS     0x20000
 
 /* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
-#define CONFIG_SYS_MVEBU_DDR
+#define CONFIG_SYS_MVEBU_DDR_AXP
 #define CONFIG_SPD_EEPROM              0x4e
 
 #endif /* _CONFIG_DB_MV7846MP_GP_H */